Subversion Repositories xulalx25soc

////////////////////////////////////////////////////////////////////////////////

//

// Filename:    wbubus.v

//

// Project:     XuLA2 board

//

// Purpose:     This is the top level file for the entire JTAG-USB to Wishbone

//              bus conversion.  (It's also the place to start debugging, should

//      things not go as planned.)  Bytes come into this routine, bytes go out,

//      and the wishbone bus (external to this routine) is commanded in between.

//

//

//

// Creator:     Dan Gisselquist, Ph.D.

//              Gisselquist Technology, LLC

//

////////////////////////////////////////////////////////////////////////////////

//

// Copyright (C) 2015, Gisselquist Technology, LLC

//

// This program is free software (firmware): you can redistribute it and/or

// modify it under the terms of  the GNU General Public License as published

// by the Free Software Foundation, either version 3 of the License, or (at

// your option) any later version.

//

// This program is distributed in the hope that it will be useful, but WITHOUT

// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or

// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License

// for more details.

//

// License:     GPL, v3, as defined and found on www.gnu.org,

//              http://www.gnu.org/licenses/gpl.html

//

//

////////////////////////////////////////////////////////////////////////////////

//

//

//

module  wbubus(i_clk, i_rx_stb, i_rx_data,

                o_wb_cyc, o_wb_stb, o_wb_we, o_wb_addr, o_wb_data,

                i_wb_ack, i_wb_stall, i_wb_err, i_wb_data,

                i_interrupt,

                o_tx_stb, o_tx_data, i_tx_busy);

        parameter       LGWATCHDOG=19;

        input                   i_clk;

        input                   i_rx_stb;

        input           [7:0]    i_rx_data;

        output  wire            o_wb_cyc, o_wb_stb, o_wb_we;

        output  wire    [31:0]   o_wb_addr, o_wb_data;

        input                   i_wb_ack, i_wb_stall, i_wb_err;

        input           [31:0]   i_wb_data;

        input                   i_interrupt;

        output  wire            o_tx_stb;

        output  wire    [7:0]    o_tx_data;

        input                   i_tx_busy;

        // output       wire    [31:0]  o_dbg;

        reg             r_wdt_reset;

        // Decode ASCII input requests into WB bus cycle requests

        wire            in_stb;

        wire    [35:0]   in_word;

        wbuinput        getinput(i_clk, i_rx_stb, i_rx_data, in_stb, in_word);

        wire    w_bus_busy, fifo_in_stb, exec_stb, w_bus_reset;

        wire    [35:0]   fifo_in_word, exec_word;

// `define      NO_INPUT_FIFO

`ifdef  NO_INPUT_FIFO

        assign  fifo_in_stb = in_stb;

        assign  fifo_in_word = in_word;

        assign  w_bus_reset = 1'b0;

`else

        wire            ififo_empty_n, ififo_err;

        assign  fifo_in_stb = (~w_bus_busy)&&(ififo_empty_n);

        assign  w_bus_reset = r_wdt_reset;

        wbufifo #(36,6) padififo(i_clk, w_bus_reset,

                                in_stb, in_word, fifo_in_stb, fifo_in_word,

                                ififo_empty_n, ififo_err);

`endif

        // Take requests in, Run the bus, send results out

        // This only works if no requests come in while requests

        // are pending.

        wbuexec runwb(i_clk, r_wdt_reset, fifo_in_stb, fifo_in_word, w_bus_busy,

                o_wb_cyc, o_wb_stb, o_wb_we, o_wb_addr, o_wb_data,

                i_wb_ack, i_wb_stall, i_wb_err, i_wb_data,

                exec_stb, exec_word);

        /*

        wire    [31:0]  cyc_debug;

        assign  cyc_debug = { 1'b0, o_wb_cyc, o_wb_stb, o_wb_we, i_wb_ack, i_wb_stall,

                                (i_wb_err||r_wdt_reset), o_wb_addr[14:0],

                                o_wb_data[4:0], i_wb_data[4:0] };

        assign  o_dbg = cyc_debug;

        */

        /*

        wire    [31:0]  fif_debug;

        assign  fif_debug = {

                        (exec_stb)&&(exec_word[35:30] == 6'h05),// 1

                        fifo_in_stb, fifo_in_word[35:30],       // 7

                        exec_stb, exec_word[35:30],             // 7

                        o_wb_cyc, o_wb_stb, o_wb_we,

                                i_wb_ack, i_wb_stall,           // 5

                        w_bus_busy, ififo_empty_n, w_bus_reset, // 3

                        i_rx_stb, o_wb_addr[7:0] };             // 9

        assign  o_dbg = fif_debug;

        */

        wire            ofifo_err;

        // wire [30:0]  out_dbg;

        wbuoutput       wroutput(i_clk, w_bus_reset,

                        exec_stb, exec_word,

                        o_wb_cyc, i_interrupt, exec_stb,

                        o_tx_stb, o_tx_data, i_tx_busy, ofifo_err);

        // Add in a watchdog timer to the bus

        reg     [(LGWATCHDOG-1):0]       r_wdt_timer;

        initial r_wdt_reset = 1'b0;

        initial r_wdt_timer = 0;

        always @(posedge i_clk)

                if ((~o_wb_cyc)||(i_wb_ack))

                begin

                        r_wdt_timer <= 0;

                        r_wdt_reset <= 1'b0;

                end else if (&r_wdt_timer)

                begin

                        r_wdt_reset <= 1'b1;

                        r_wdt_timer <= 0;

                end else begin

                        r_wdt_timer <= r_wdt_timer+{{(LGWATCHDOG-1){1'b0}},1'b1};

                        r_wdt_reset <= 1'b0;

                end

endmodule