Subversion Repositories xulalx25soc

////////////////////////////////////////////////////////////////////////////////

//

// Filename:    wbufifo.v

//

// Project:     XuLA2 board

//

// Purpose:     This was once a FIFO for a UART ... but now it works as a

//              synchronous FIFO for JTAG-wishbone conversion 36-bit codewords.  

//

//

// Creator:     Dan Gisselquist, Ph.D.

//              Gisselquist Technology, LLC

//

////////////////////////////////////////////////////////////////////////////////

//

// Copyright (C) 2015, Gisselquist Technology, LLC

//

// This program is free software (firmware): you can redistribute it and/or

// modify it under the terms of  the GNU General Public License as published

// by the Free Software Foundation, either version 3 of the License, or (at

// your option) any later version.

//

// This program is distributed in the hope that it will be useful, but WITHOUT

// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or

// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License

// for more details.

//

// License:     GPL, v3, as defined and found on www.gnu.org,

//              http://www.gnu.org/licenses/gpl.html

//

//

////////////////////////////////////////////////////////////////////////////////

//

//

module wbufifo(i_clk, i_rst, i_wr, i_data, i_rd, o_data, o_empty_n, o_err);

        parameter       BW=66, LGFLEN=10, FLEN=(1<<LGFLEN);

        input                   i_clk, i_rst;

        input                   i_wr;

        input   [(BW-1):0]       i_data;

        input                   i_rd;

        output  reg [(BW-1):0]   o_data;

        output  reg             o_empty_n;

        output  wire            o_err;

        reg     [(BW-1):0]       fifo[0:(FLEN-1)];

        reg     [(LGFLEN-1):0]   r_first, r_last;

        // Write

        initial r_first = 0;

        always @(posedge i_clk)

                if (i_rst)

                        r_first <= { (LGFLEN){1'b0} };

                else if (i_wr)

                begin // Cowardly refuse to overflow

                        if (r_first+1 != r_last)

                                r_first <= r_first+{{(LGFLEN-1){1'b0}},1'b1};

                        // else o_ovfl <= 1'b1;

                end

        always @(posedge i_clk)

                if (i_wr) // Write our new value regardless--on overflow or not

                        fifo[r_first] <= i_data;

        initial r_last = 0;

        // Reads

        //      Following a read, the next sample will be available on the

        //      next clock

        //      Clock   ReadCMD ReadAddr        Output

        //      0        0        0                fifo[0]

        //      1       1       0                fifo[0]

        //      2       0        1               fifo[1]

        //      3       0        1               fifo[1]

        //      4       1       1               fifo[1]

        //      5       1       2               fifo[2]

        //      6       0        3               fifo[3]

        //      7       0        3               fifo[3]

        always @(posedge i_clk)

                if (i_rst)

                        r_last <= { (LGFLEN){1'b0} };

                else if (i_rd)

                begin

                        if (r_first != r_last)

                                r_last <= r_last+{{(LGFLEN-1){1'b0}},1'b1};

                                // Last chases first

                                // Need to be prepared for a possible two

                                // reads in quick succession

                                // o_data <= fifo[r_last+1];

                        // else o_unfl <= 1'b1;

                end

        always @(posedge i_clk)

                o_data <= fifo[(i_rd)?(r_last+{{(LGFLEN-1){1'b0}},1'b1})

                                        :(r_last)];

        wire    [(LGFLEN-1):0]   nxt_first;

        assign  nxt_first = r_first+{{(LGFLEN-1){1'b0}},1'b1};

        assign  o_err = ((i_wr)&&(nxt_first == r_last))

                                ||((i_rd)&&(r_first == r_last));

        // wire [(LGFLEN-1):0]  fill;

        // assign       fill = (r_first-r_last);

        wire    [(LGFLEN-1):0]   nxt_last;

        assign  nxt_last = r_last+{{(LGFLEN-1){1'b0}},1'b1};

        always @(posedge i_clk)

                if (i_rst)

                        o_empty_n <= 1'b0;

                else

                        o_empty_n <= (~i_rd)&&(r_first != r_last)

                                        ||(i_rd)&&(r_first != nxt_last);

endmodule