URL https://opencores.org/ocsvn/openarty/openarty/trunk

Subversion Repositories openarty

[/] [openarty/] [trunk/] [rtl/] [txuart.v] - Blame information for rev 3

Go to most recent revision | Details | Compare with Previous | View Log


////////////////////////////////////////////////////////////////////////////////
//
// Filename:    txuart.v
//
// Project:     FPGA library
//
// Purpose:     Transmit outputs over a single UART line.
//
//      To interface with this module, connect it to your system clock,
//      pass it the 32 bit setup register (defined below) and the byte
//      of data you wish to transmit.  Strobe the i_wr line high for one
//      clock cycle, and your data will be off.  Wait until the 'o_busy'
//      line is low before strobing the i_wr line again--this implementation
//      has NO BUFFER, so strobing i_wr while the core is busy will just
//      cause your data to be lost.  The output will be placed on the o_txuart
//      output line.  If you wish to set/send a break condition, assert the
//      i_break line otherwise leave it low.
//
//      There is a synchronous reset line, logic high.
//
//      Now for the setup register.  The register is 32 bits, so that this
//      UART may be set up over a 32-bit bus.
//
//      i_setup[29:28]  Indicates the number of data bits per word.  This will
//      either be 2'b00 for an 8-bit word, 2'b01 for a 7-bit word, 2'b10
//      for a six bit word, or 2'b11 for a five bit word.
//
//      i_setup[27]     Indicates whether or not to use one or two stop bits.
//              Set this to one to expect two stop bits, zero for one.
//
//      i_setup[26]     Indicates whether or not a parity bit exists.  Set this
//              to 1'b1 to include parity.
//
//      i_setup[25]     Indicates whether or not the parity bit is fixed.  Set
//              to 1'b1 to include a fixed bit of parity, 1'b0 to allow the
//              parity to be set based upon data.  (Both assume the parity
//              enable value is set.)
//
//      i_setup[24]     This bit is ignored if parity is not used.  Otherwise,
//              in the case of a fixed parity bit, this bit indicates whether
//              mark (1'b1) or space (1'b0) parity is used.  Likewise if the
//              parity is not fixed, a 1'b1 selects even parity, and 1'b0
//              selects odd.
//
//      i_setup[23:0]   Indicates the speed of the UART in terms of clocks.
//              So, for example, if you have a 200 MHz clock and wish to
//              run your UART at 9600 baud, you would take 200 MHz and divide
//              by 9600 to set this value to 24'd20834.  Likewise if you wished
//              to run this serial port at 115200 baud from a 200 MHz clock,
//              you would set the value to 24'd1736
//
//      Thus, to set the UART for the common setting of an 8-bit word, 
//      one stop bit, no parity, and 115200 baud over a 200 MHz clock, you
//      would want to set the setup value to:
//
//      32'h0006c8              // For 115,200 baud, 8 bit, no parity
//      32'h005161              // For 9600 baud, 8 bit, no parity
//      
//
//
// Creator:     Dan Gisselquist, Ph.D.
//              Gisselquist Technology, LLC
//
////////////////////////////////////////////////////////////////////////////////
//
// Copyright (C) 2015-2016, Gisselquist Technology, LLC
//
// This program is free software (firmware): you can redistribute it and/or
// modify it under the terms of  the GNU General Public License as published
// by the Free Software Foundation, either version 3 of the License, or (at
// your option) any later version.
//
// This program is distributed in the hope that it will be useful, but WITHOUT
// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
// for more details.
//
// You should have received a copy of the GNU General Public License along
// with this program.  (It's in the $(ROOT)/doc directory, run make with no
// target there if the PDF file isn't present.)  If not, see
// <http://www.gnu.org/licenses/> for a copy.
//
// License:     GPL, v3, as defined and found on www.gnu.org,
//              http://www.gnu.org/licenses/gpl.html
//
//
////////////////////////////////////////////////////////////////////////////////
//
//
//
`define TXU_BIT_ZERO    4'h0
`define TXU_BIT_ONE     4'h1
`define TXU_BIT_TWO     4'h2
`define TXU_BIT_THREE   4'h3
`define TXU_BIT_FOUR    4'h4
`define TXU_BIT_FIVE    4'h5
`define TXU_BIT_SIX     4'h6
`define TXU_BIT_SEVEN   4'h7
`define TXU_PARITY      4'h8    // Constant 1
`define TXU_STOP        4'h9    // Constant 1
`define TXU_SECOND_STOP 4'ha
// 4'hb // Unused
// 4'hc // Unused
// `define      TXU_START       4'hd    // An unused state
`define TXU_BREAK       4'he
`define TXU_IDLE        4'hf
//
//
module txuart(i_clk, i_reset, i_setup, i_break, i_wr, i_data, o_uart, o_busy);
        input                   i_clk, i_reset;
        input           [29:0]   i_setup;
        input                   i_break;
        input                   i_wr;
        input           [7:0]    i_data;
        output  reg             o_uart;
        output  wire            o_busy;
 
        wire    [27:0]   clocks_per_baud, break_condition;
        wire    [1:0]    data_bits;
        wire            use_parity, parity_even, dblstop, fixd_parity;
        reg     [29:0]   r_setup;
        assign  clocks_per_baud = { 4'h0, r_setup[23:0] };
        assign  break_condition = { r_setup[23:0], 4'h0 };
        assign  data_bits   = r_setup[29:28];
        assign  dblstop     = r_setup[27];
        assign  use_parity  = r_setup[26];
        assign  fixd_parity = r_setup[25];
        assign  parity_even = r_setup[24];
 
        reg     [27:0]   baud_counter;
        reg     [3:0]    state;
        reg     [7:0]    lcl_data;
        reg             calc_parity, r_busy, zero_baud_counter;
 
        initial o_uart = 1'b1;
        initial r_busy = 1'b1;
        initial state  = `TXU_IDLE;
        initial lcl_data= 8'h0;
        initial calc_parity = 1'b0;
        // initial      baud_counter = clocks_per_baud;//ILLEGAL--not constant
        always @(posedge i_clk)
        begin
                if (i_reset)
                begin
                        o_uart <= 1'b1;
                        r_busy <= 1'b1;
                        state <= `TXU_IDLE;
                        lcl_data <= 8'h0;
                        calc_parity <= 1'b0;
                end else if (i_break)
                begin
                        o_uart <= 1'b0;
                        state <= `TXU_BREAK;
                        calc_parity <= 1'b0;
                        r_busy <= 1'b1;
                end else if (~zero_baud_counter)
                begin // r_busy needs to be set coming into here
                        r_busy <= 1'b1;
                end else if (state == `TXU_BREAK)
                begin
                        state <= `TXU_IDLE;
                        r_busy <= 1'b1;
                        o_uart <= 1'b1;
                        calc_parity <= 1'b0;
                end else if (state == `TXU_IDLE)        // STATE_IDLE
                begin
                        // baud_counter <= 0;
                        r_setup <= i_setup;
                        calc_parity <= 1'b0;
                        if ((i_wr)&&(~r_busy))
                        begin   // Immediately start us off with a start bit
                                o_uart <= 1'b0;
                                r_busy <= 1'b1;
                                case(data_bits)
                                2'b00: state <= `TXU_BIT_ZERO;
                                2'b01: state <= `TXU_BIT_ONE;
                                2'b10: state <= `TXU_BIT_TWO;
                                2'b11: state <= `TXU_BIT_THREE;
                                endcase
                                lcl_data <= i_data;
                                // baud_counter <= clocks_per_baud-28'h01;
                        end else begin // Stay in idle
                                o_uart <= 1'b1;
                                r_busy <= 0;
                                // lcl_data is irrelevant
                                // state <= state;
                        end
                end else begin
                        // One clock tick in each of these states ...
                        // baud_counter <= clocks_per_baud - 28'h01;
                        r_busy <= 1'b1;
                        if (state[3] == 0) // First 8 bits
                        begin
                                o_uart <= lcl_data[0];
                                calc_parity <= calc_parity ^ lcl_data[0];
                                if (state == `TXU_BIT_SEVEN)
                                        state <= (use_parity)?`TXU_PARITY:`TXU_STOP;
                                else
                                        state <= state + 1;
                                lcl_data <= { 1'b0, lcl_data[7:1] };
                        end else if (state == `TXU_PARITY)
                        begin
                                state <= `TXU_STOP;
                                if (fixd_parity)
                                        o_uart <= parity_even;
                                else
                                        o_uart <= calc_parity^((parity_even)? 1'b1:1'b0);
                        end else if (state == `TXU_STOP)
                        begin // two stop bit(s)
                                o_uart <= 1'b1;
                                if (dblstop)
                                        state <= `TXU_SECOND_STOP;
                                else
                                        state <= `TXU_IDLE;
                                calc_parity <= 1'b0;
                        end else // `TXU_SECOND_STOP and default:
                        begin
                                state <= `TXU_IDLE; // Go back to idle
                                o_uart <= 1'b1;
                                // Still r_busy, since we need to wait
                                // for the baud clock to finish counting
                                // out this last bit.
                        end
                end
        end
 
        assign  o_busy = (r_busy);
 
 
        initial zero_baud_counter = 1'b0;
        always @(posedge i_clk)
        begin
                zero_baud_counter <= (baud_counter == 28'h01);
                if ((i_reset)||(i_break))
                        // Give ourselves 16 bauds before being ready
                        baud_counter <= break_condition;
                else if (~zero_baud_counter)
                        baud_counter <= baud_counter - 28'h01;
                else if (state == `TXU_BREAK)
                        // Give us two stop bits before becoming available
                        baud_counter <= clocks_per_baud<<2;
                else if (state == `TXU_IDLE)
                begin
                        if((i_wr)&&(~r_busy))
                                baud_counter <= clocks_per_baud - 28'h01;
                        else
                                zero_baud_counter <= 1'b1;
                end else
                        baud_counter <= clocks_per_baud - 28'h01;
        end
endmodule
 

Browse

Tools

Subversion Repositories openarty

[/] [openarty/] [trunk/] [rtl/] [txuart.v] - Blame information for rev 3

Line No.	Rev	Author	Line
1	3	dgisselq	`////////////////////////////////////////////////////////////////////////////////`
2			`//`
3			`// Filename: txuart.v`
4			`//`
5			`// Project: FPGA library`
6			`//`
7			`// Purpose: Transmit outputs over a single UART line.`
8			`//`
9			`// To interface with this module, connect it to your system clock,`
10			`// pass it the 32 bit setup register (defined below) and the byte`
11			`// of data you wish to transmit. Strobe the i_wr line high for one`
12			`// clock cycle, and your data will be off. Wait until the 'o_busy'`
13			`// line is low before strobing the i_wr line again--this implementation`
14			`// has NO BUFFER, so strobing i_wr while the core is busy will just`
15			`// cause your data to be lost. The output will be placed on the o_txuart`
16			`// output line. If you wish to set/send a break condition, assert the`
17			`// i_break line otherwise leave it low.`
18			`//`
19			`// There is a synchronous reset line, logic high.`
20			`//`
21			`// Now for the setup register. The register is 32 bits, so that this`
22			`// UART may be set up over a 32-bit bus.`
23			`//`
24			`// i_setup[29:28] Indicates the number of data bits per word. This will`
25			`// either be 2'b00 for an 8-bit word, 2'b01 for a 7-bit word, 2'b10`
26			`// for a six bit word, or 2'b11 for a five bit word.`
27			`//`
28			`// i_setup[27] Indicates whether or not to use one or two stop bits.`
29			`// Set this to one to expect two stop bits, zero for one.`
30			`//`
31			`// i_setup[26] Indicates whether or not a parity bit exists. Set this`
32			`// to 1'b1 to include parity.`
33			`//`
34			`// i_setup[25] Indicates whether or not the parity bit is fixed. Set`
35			`// to 1'b1 to include a fixed bit of parity, 1'b0 to allow the`
36			`// parity to be set based upon data. (Both assume the parity`
37			`// enable value is set.)`
38			`//`
39			`// i_setup[24] This bit is ignored if parity is not used. Otherwise,`
40			`// in the case of a fixed parity bit, this bit indicates whether`
41			`// mark (1'b1) or space (1'b0) parity is used. Likewise if the`
42			`// parity is not fixed, a 1'b1 selects even parity, and 1'b0`
43			`// selects odd.`
44			`//`
45			`// i_setup[23:0] Indicates the speed of the UART in terms of clocks.`
46			`// So, for example, if you have a 200 MHz clock and wish to`
47			`// run your UART at 9600 baud, you would take 200 MHz and divide`
48			`// by 9600 to set this value to 24'd20834. Likewise if you wished`
49			`// to run this serial port at 115200 baud from a 200 MHz clock,`
50			`// you would set the value to 24'd1736`
51			`//`
52			`// Thus, to set the UART for the common setting of an 8-bit word,`
53			`// one stop bit, no parity, and 115200 baud over a 200 MHz clock, you`
54			`// would want to set the setup value to:`
55			`//`
56			`// 32'h0006c8 // For 115,200 baud, 8 bit, no parity`
57			`// 32'h005161 // For 9600 baud, 8 bit, no parity`
58			`//`
59			`//`
60			`//`
61			`// Creator: Dan Gisselquist, Ph.D.`
62			`// Gisselquist Technology, LLC`
63			`//`
64			`////////////////////////////////////////////////////////////////////////////////`
65			`//`
66			`// Copyright (C) 2015-2016, Gisselquist Technology, LLC`
67			`//`
68			`// This program is free software (firmware): you can redistribute it and/or`
69			`// modify it under the terms of the GNU General Public License as published`
70			`// by the Free Software Foundation, either version 3 of the License, or (at`
71			`// your option) any later version.`
72			`//`
73			`// This program is distributed in the hope that it will be useful, but WITHOUT`
74			`// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or`
75			`// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License`
76			`// for more details.`
77			`//`
78			`// You should have received a copy of the GNU General Public License along`
79			`// with this program. (It's in the $(ROOT)/doc directory, run make with no`
80			`// target there if the PDF file isn't present.) If not, see`
81			`// <http://www.gnu.org/licenses/> for a copy.`
82			`//`
83			`// License: GPL, v3, as defined and found on www.gnu.org,`
84			`// http://www.gnu.org/licenses/gpl.html`
85			`//`
86			`//`
87			`////////////////////////////////////////////////////////////////////////////////`
88			`//`
89			`//`
90			`//`
91			`define TXU_BIT_ZERO 4'h0
92			`define TXU_BIT_ONE 4'h1
93			`define TXU_BIT_TWO 4'h2
94			`define TXU_BIT_THREE 4'h3
95			`define TXU_BIT_FOUR 4'h4
96			`define TXU_BIT_FIVE 4'h5
97			`define TXU_BIT_SIX 4'h6
98			`define TXU_BIT_SEVEN 4'h7
99			`define TXU_PARITY 4'h8 // Constant 1
100			`define TXU_STOP 4'h9 // Constant 1
101			`define TXU_SECOND_STOP 4'ha
102			`// 4'hb // Unused`
103			`// 4'hc // Unused`
104			// `define TXU_START 4'hd // An unused state
105			`define TXU_BREAK 4'he
106			`define TXU_IDLE 4'hf
107			`//`
108			`//`
109			`module txuart(i_clk, i_reset, i_setup, i_break, i_wr, i_data, o_uart, o_busy);`
110			`input i_clk, i_reset;`
111			`input [29:0] i_setup;`
112			`input i_break;`
113			`input i_wr;`
114			`input [7:0] i_data;`
115			`output reg o_uart;`
116			`output wire o_busy;`
117
118			`wire [27:0] clocks_per_baud, break_condition;`
119			`wire [1:0] data_bits;`
120			`wire use_parity, parity_even, dblstop, fixd_parity;`
121			`reg [29:0] r_setup;`
122			`assign clocks_per_baud = { 4'h0, r_setup[23:0] };`
123			`assign break_condition = { r_setup[23:0], 4'h0 };`
124			`assign data_bits = r_setup[29:28];`
125			`assign dblstop = r_setup[27];`
126			`assign use_parity = r_setup[26];`
127			`assign fixd_parity = r_setup[25];`
128			`assign parity_even = r_setup[24];`
129
130			`reg [27:0] baud_counter;`
131			`reg [3:0] state;`
132			`reg [7:0] lcl_data;`
133			`reg calc_parity, r_busy, zero_baud_counter;`
134
135			`initial o_uart = 1'b1;`
136			`initial r_busy = 1'b1;`
137			initial state = `TXU_IDLE;
138			`initial lcl_data= 8'h0;`
139			`initial calc_parity = 1'b0;`
140			`// initial baud_counter = clocks_per_baud;//ILLEGAL--not constant`
141			`always @(posedge i_clk)`
142			`begin`
143			`if (i_reset)`
144			`begin`
145			`o_uart <= 1'b1;`
146			`r_busy <= 1'b1;`
147			state <= `TXU_IDLE;
148			`lcl_data <= 8'h0;`
149			`calc_parity <= 1'b0;`
150			`end else if (i_break)`
151			`begin`
152			`o_uart <= 1'b0;`
153			state <= `TXU_BREAK;
154			`calc_parity <= 1'b0;`
155			`r_busy <= 1'b1;`
156			`end else if (~zero_baud_counter)`
157			`begin // r_busy needs to be set coming into here`
158			`r_busy <= 1'b1;`
159			end else if (state == `TXU_BREAK)
160			`begin`
161			state <= `TXU_IDLE;
162			`r_busy <= 1'b1;`
163			`o_uart <= 1'b1;`
164			`calc_parity <= 1'b0;`
165			end else if (state == `TXU_IDLE) // STATE_IDLE
166			`begin`
167			`// baud_counter <= 0;`
168			`r_setup <= i_setup;`
169			`calc_parity <= 1'b0;`
170			`if ((i_wr)&&(~r_busy))`
171			`begin // Immediately start us off with a start bit`
172			`o_uart <= 1'b0;`
173			`r_busy <= 1'b1;`
174			`case(data_bits)`
175			2'b00: state <= `TXU_BIT_ZERO;
176			2'b01: state <= `TXU_BIT_ONE;
177			2'b10: state <= `TXU_BIT_TWO;
178			2'b11: state <= `TXU_BIT_THREE;
179			`endcase`
180			`lcl_data <= i_data;`
181			`// baud_counter <= clocks_per_baud-28'h01;`
182			`end else begin // Stay in idle`
183			`o_uart <= 1'b1;`
184			`r_busy <= 0;`
185			`// lcl_data is irrelevant`
186			`// state <= state;`
187			`end`
188			`end else begin`
189			`// One clock tick in each of these states ...`
190			`// baud_counter <= clocks_per_baud - 28'h01;`
191			`r_busy <= 1'b1;`
192			`if (state[3] == 0) // First 8 bits`
193			`begin`
194			`o_uart <= lcl_data[0];`
195			`calc_parity <= calc_parity ^ lcl_data[0];`
196			if (state == `TXU_BIT_SEVEN)
197			state <= (use_parity)?`TXU_PARITY:`TXU_STOP;
198			`else`
199			`state <= state + 1;`
200			`lcl_data <= { 1'b0, lcl_data[7:1] };`
201			end else if (state == `TXU_PARITY)
202			`begin`
203			state <= `TXU_STOP;
204			`if (fixd_parity)`
205			`o_uart <= parity_even;`
206			`else`
207			`o_uart <= calc_parity^((parity_even)? 1'b1:1'b0);`
208			end else if (state == `TXU_STOP)
209			`begin // two stop bit(s)`
210			`o_uart <= 1'b1;`
211			`if (dblstop)`
212			state <= `TXU_SECOND_STOP;
213			`else`
214			state <= `TXU_IDLE;
215			`calc_parity <= 1'b0;`
216			end else // `TXU_SECOND_STOP and default:
217			`begin`
218			state <= `TXU_IDLE; // Go back to idle
219			`o_uart <= 1'b1;`
220			`// Still r_busy, since we need to wait`
221			`// for the baud clock to finish counting`
222			`// out this last bit.`
223			`end`
224			`end`
225			`end`
226
227			`assign o_busy = (r_busy);`
228
229
230			`initial zero_baud_counter = 1'b0;`
231			`always @(posedge i_clk)`
232			`begin`
233			`zero_baud_counter <= (baud_counter == 28'h01);`
234			`if ((i_reset)\|\|(i_break))`
235			`// Give ourselves 16 bauds before being ready`
236			`baud_counter <= break_condition;`
237			`else if (~zero_baud_counter)`
238			`baud_counter <= baud_counter - 28'h01;`
239			else if (state == `TXU_BREAK)
240			`// Give us two stop bits before becoming available`
241			`baud_counter <= clocks_per_baud<<2;`
242			else if (state == `TXU_IDLE)
243			`begin`
244			`if((i_wr)&&(~r_busy))`
245			`baud_counter <= clocks_per_baud - 28'h01;`
246			`else`
247			`zero_baud_counter <= 1'b1;`
248			`end else`
249			`baud_counter <= clocks_per_baud - 28'h01;`
250			`end`
251			`endmodule`
252