Subversion Repositories openrisc

/////////////////////////////////////////////////////////////////////

////                                                             ////

////  WISHBONE rev.B2 compliant I2C Master bit-controller        ////

////                                                             ////

////                                                             ////

////  Author: Richard Herveille                                  ////

////          richard@asics.ws                                   ////

////          www.asics.ws                                       ////

////                                                             ////

////  Downloaded from: http://www.opencores.org/projects/i2c/    ////

////                                                             ////

/////////////////////////////////////////////////////////////////////

////                                                             ////

//// Copyright (C) 2001 Richard Herveille                        ////

////                    richard@asics.ws                         ////

////                                                             ////

//// This source file may be used and distributed without        ////

//// restriction provided that this copyright statement is not   ////

//// removed from the file and that any derivative work contains ////

//// the original copyright notice and the associated disclaimer.////

////                                                             ////

////     THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY     ////

//// EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED   ////

//// TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS   ////

//// FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE AUTHOR      ////

//// OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,         ////

//// INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES    ////

//// (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE   ////

//// GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR        ////

//// BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF  ////

//// LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT  ////

//// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT  ////

//// OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE         ////

//// POSSIBILITY OF SUCH DAMAGE.                                 ////

////                                                             ////

/////////////////////////////////////////////////////////////////////

//  CVS Log

//

//  $Id: i2c_master_bit_ctrl.v,v 1.14 2009-01-20 10:25:29 rherveille Exp $

//

//  $Date: 2009-01-20 10:25:29 $

//  $Revision: 1.14 $

//  $Author: rherveille $

//  $Locker:  $

//  $State: Exp $

//

// Change History:

//               $Log: $

//               Revision 1.14  2009/01/20 10:25:29  rherveille

//               Added clock synchronization logic

//               Fixed slave_wait signal

//

//               Revision 1.13  2009/01/19 20:29:26  rherveille

//               Fixed synopsys miss spell (synopsis)

//               Fixed cr[0] register width

//               Fixed ! usage instead of ~

//               Fixed bit controller parameter width to 18bits

//

//               Revision 1.12  2006/09/04 09:08:13  rherveille

//               fixed short scl high pulse after clock stretch

//               fixed slave model not returning correct '(n)ack' signal

//

//               Revision 1.11  2004/05/07 11:02:26  rherveille

//               Fixed a bug where the core would signal an arbitration lost (AL bit set), when another master controls the bus and the other master generates a STOP bit.

//

//               Revision 1.10  2003/08/09 07:01:33  rherveille

//               Fixed a bug in the Arbitration Lost generation caused by delay on the (external) sda line.

//               Fixed a potential bug in the byte controller's host-acknowledge generation.

//

//               Revision 1.9  2003/03/10 14:26:37  rherveille

//               Fixed cmd_ack generation item (no bug).

//

//               Revision 1.8  2003/02/05 00:06:10  rherveille

//               Fixed a bug where the core would trigger an erroneous 'arbitration lost' interrupt after being reset, when the reset pulse width < 3 clk cycles.

//

//               Revision 1.7  2002/12/26 16:05:12  rherveille

//               Small code simplifications

//

//               Revision 1.6  2002/12/26 15:02:32  rherveille

//               Core is now a Multimaster I2C controller

//

//               Revision 1.5  2002/11/30 22:24:40  rherveille

//               Cleaned up code

//

//               Revision 1.4  2002/10/30 18:10:07  rherveille

//               Fixed some reported minor start/stop generation timing issuess.

//

//               Revision 1.3  2002/06/15 07:37:03  rherveille

//               Fixed a small timing bug in the bit controller.\nAdded verilog simulation environment.

//

//               Revision 1.2  2001/11/05 11:59:25  rherveille

//               Fixed wb_ack_o generation bug.

//               Fixed bug in the byte_controller statemachine.

//               Added headers.

//

//

/////////////////////////////////////

// Bit controller section

/////////////////////////////////////

//

// Translate simple commands into SCL/SDA transitions

// Each command has 5 states, A/B/C/D/idle

//

// start:       SCL     ~~~~~~~~~~\____

//      SDA     ~~~~~~~~\______

//               x | A | B | C | D | i

//

// repstart     SCL     ____/~~~~\___

//      SDA     __/~~~\______

//               x | A | B | C | D | i

//

// stop SCL     ____/~~~~~~~~

//      SDA     ==\____/~~~~~

//               x | A | B | C | D | i

//

//- write       SCL     ____/~~~~\____

//      SDA     ==X=========X=

//               x | A | B | C | D | i

//

//- read        SCL     ____/~~~~\____

//      SDA     XXXX=====XXXX

//               x | A | B | C | D | i

//

// Timing:     Normal mode      Fast mode

///////////////////////////////////////////////////////////////////////

// Fscl        100KHz           400KHz

// Th_scl      4.0us            0.6us   High period of SCL

// Tl_scl      4.7us            1.3us   Low period of SCL

// Tsu:sta     4.7us            0.6us   setup time for a repeated start condition

// Tsu:sto     4.0us            0.6us   setup time for a stop conditon

// Tbuf        4.7us            1.3us   Bus free time between a stop and start condition

//

// synopsys translate_off

`include "timescale.v"

// synopsys translate_on

`include "i2c_master_slave_defines.v"

module i2c_master_bit_ctrl (

    input             clk,      // system clock

    input             rst,      // synchronous active high reset

    input             nReset,   // asynchronous active low reset

    input             ena,      // core enable signal

    input [15:0]      clk_cnt,  // clock prescale value

    input [ 3:0]      cmd,      // command (from byte controller)

    output reg        cmd_ack,  // command complete acknowledge

    output reg        busy,     // i2c bus busy

    output reg        al,       // i2c bus arbitration lost

    input             din,

    output reg        dout,

    input             scl_i,    // i2c clock line input

    output            scl_o,    // i2c clock line output

    output            scl_oen,  // i2c clock line output enable (active low)

    input             sda_i,    // i2c data line input

    output            sda_o,    // i2c data line output

    output            sda_oen,  // i2c data line output enable (active low)

    output reg        slave_adr_received,

    output reg [7:0]  slave_adr,

    input             master_mode,

    output reg        cmd_slave_ack,

    input [1:0]       slave_cmd ,

    input             sl_wait,

    output            slave_reset

                            );

   //

   // variable declarations

   //

   reg [ 1:0]          cSCL, cSDA;      // capture SCL and SDA

   reg [ 2:0]          fSCL, fSDA;      // SCL and SDA filter inputs

   reg                sSCL, sSDA;      // filtered and synchronized SCL and SDA inputs

   reg                dSCL, dSDA;      // delayed versions of sSCL and sSDA

   reg                dscl_oen;        // delayed scl_oen

   reg                sda_chk;         // check SDA output (Multi-master arbitration)

   reg                clk_en;          // clock generation signals

   reg                slave_wait;      // slave inserts wait states

   reg [15:0]          cnt;             // clock divider counter (synthesis)

   reg [13:0]          filter_cnt;      // clock divider for filter

   // state machine variable

   reg [17:0]          c_state; // synopsys enum_state

   reg [4:0]           slave_state;

   //

   // module body

   //

   // whenever the slave is not ready it can delay the cycle by pulling SCL low

   // delay scl_oen

   always @(posedge clk)

     dscl_oen <=  scl_oen;

   // slave_wait is asserted when master wants to drive SCL high, but the slave pulls it low

   // slave_wait remains asserted until the slave releases SCL

   always @(posedge clk or negedge nReset)

     if (!nReset) slave_wait <= 1'b0;

     else         slave_wait <= (scl_oen & ~dscl_oen & ~sSCL) | (slave_wait & ~sSCL);

   // master drives SCL high, but another master pulls it low

   // master start counting down its low cycle now (clock synchronization)

   wire               scl_sync   = dSCL & ~sSCL & scl_oen;

   // generate clk enable signal

   always @(posedge clk or negedge nReset)

     if (~nReset)

       begin

          cnt    <=  16'h0;

          clk_en <=  1'b1;

       end

     else if (rst || ~|cnt || !ena || scl_sync)

       begin

          cnt    <=  clk_cnt;

          clk_en <=  1'b1;

       end

     else if (slave_wait)

       begin

          cnt    <=  cnt;

          clk_en <=  1'b0;

       end

     else

       begin

          cnt    <=  cnt - 16'h1;

          clk_en <=  1'b0;

       end

   // generate bus status controller

   // capture SDA and SCL

   // reduce metastability risk

   always @(posedge clk or negedge nReset)

     if (!nReset)

       begin

          cSCL <=  2'b00;

          cSDA <=  2'b00;

       end

     else if (rst)

       begin

          cSCL <=  2'b00;

          cSDA <=  2'b00;

       end

     else

       begin

          cSCL <= {cSCL[0],scl_i};

          cSDA <= {cSDA[0],sda_i};

       end

   // filter SCL and SDA signals; (attempt to) remove glitches

   always @(posedge clk or negedge nReset)

     if      (!nReset     ) filter_cnt <= 14'h0;

     else if (rst || !ena ) filter_cnt <= 14'h0;

     else if (~|filter_cnt) filter_cnt <= clk_cnt >> 2; //16x I2C bus frequency

     else                   filter_cnt <= filter_cnt -1;

   always @(posedge clk or negedge nReset)

     if (!nReset)

       begin

          fSCL <= 3'b111;

          fSDA <= 3'b111;

       end

     else if (rst)

       begin

          fSCL <= 3'b111;

          fSDA <= 3'b111;

       end

     else if (~|filter_cnt)

       begin

          fSCL <= {fSCL[1:0],cSCL[1]};

          fSDA <= {fSDA[1:0],cSDA[1]};

       end

   // generate filtered SCL and SDA signals

   always @(posedge clk or negedge nReset)

     if (~nReset)

       begin

          sSCL <=  1'b1;

          sSDA <=  1'b1;

          dSCL <=  1'b1;

          dSDA <=  1'b1;

       end

     else if (rst)

       begin

          sSCL <=  1'b1;

          sSDA <=  1'b1;

          dSCL <=  1'b1;

          dSDA <=  1'b1;

       end

     else

       begin

          sSCL <=  &fSCL[2:1] | &fSCL[1:0] | (fSCL[2] & fSCL[0]);

          sSDA <=  &fSDA[2:1] | &fSDA[1:0] | (fSDA[2] & fSDA[0]);

          dSCL <=  sSCL;

          dSDA <=  sSDA;

       end

   // detect start condition => detect falling edge on SDA while SCL is high

   // detect stop condition => detect rising edge on SDA while SCL is high

   reg sta_condition;

   reg sto_condition;

   always @(posedge clk or negedge nReset)

     if (~nReset)

       begin

          sta_condition <=  1'b0;

          sto_condition <=  1'b0;

       end

     else if (rst)

       begin

          sta_condition <=  1'b0;

          sto_condition <=  1'b0;

       end

     else

       begin

          sta_condition  <=  ~sSDA &  dSDA & sSCL;

          sto_condition  <=   sSDA & ~dSDA & sSCL;

       end

   // generate i2c bus busy signal

   always @(posedge clk or negedge nReset)

     if      (!nReset) busy <=  1'b0;

     else if (rst    ) busy <=  1'b0;

     else              busy <=  (sta_condition | busy) & ~sto_condition;

   //

   // generate arbitration lost signal

   // aribitration lost when:

   // 1) master drives SDA high, but the i2c bus is low

   // 2) stop detected while not requested

   reg cmd_stop;

   always @(posedge clk or negedge nReset)

     if (~nReset)

       cmd_stop <=  1'b0;

     else if (rst)

       cmd_stop <=  1'b0;

     else if (clk_en)

       cmd_stop <=  cmd == `I2C_CMD_STOP;

   always @(posedge clk or negedge nReset)

     if (~nReset)

       al <=  1'b0;

     else if (rst)

       al <=  1'b0;

     else

       al <=  (sda_chk & ~sSDA & sda_oen) | (|c_state & sto_condition & ~cmd_stop);

   // generate dout signal (store SDA on rising edge of SCL)

   always @(posedge clk)

     if (sSCL & ~dSCL) dout <=  sSDA;

   // generate statemachine

   // nxt_state decoder

   parameter [17:0] idle    = 18'b0_0000_0000_0000_0000;

   parameter [17:0] start_a = 18'b0_0000_0000_0000_0001;

   parameter [17:0] start_b = 18'b0_0000_0000_0000_0010;

   parameter [17:0] start_c = 18'b0_0000_0000_0000_0100;

   parameter [17:0] start_d = 18'b0_0000_0000_0000_1000;

   parameter [17:0] start_e = 18'b0_0000_0000_0001_0000;

   parameter [17:0] stop_a  = 18'b0_0000_0000_0010_0000;

   parameter [17:0] stop_b  = 18'b0_0000_0000_0100_0000;

   parameter [17:0] stop_c  = 18'b0_0000_0000_1000_0000;

   parameter [17:0] stop_d  = 18'b0_0000_0001_0000_0000;

   parameter [17:0] rd_a    = 18'b0_0000_0010_0000_0000;

   parameter [17:0] rd_b    = 18'b0_0000_0100_0000_0000;

   parameter [17:0] rd_c    = 18'b0_0000_1000_0000_0000;

   parameter [17:0] rd_d    = 18'b0_0001_0000_0000_0000;

   parameter [17:0] wr_a    = 18'b0_0010_0000_0000_0000;

   parameter [17:0] wr_b    = 18'b0_0100_0000_0000_0000;

   parameter [17:0] wr_c    = 18'b0_1000_0000_0000_0000;

   parameter [17:0] wr_d    = 18'b1_0000_0000_0000_0000;

   reg scl_oen_master ;

   reg sda_oen_master ;

   reg sda_oen_slave;

   reg scl_oen_slave;

   always @(posedge clk or negedge nReset)

     if (!nReset)

       begin

          c_state <=  idle;

          cmd_ack <=  1'b0;

          scl_oen_master <=  1'b1;

          sda_oen_master <=  1'b1;

          sda_chk <=  1'b0;

       end

     else if (rst | al)

       begin

          c_state <=  idle;

          cmd_ack <=  1'b0;

          scl_oen_master <=  1'b1;

          sda_oen_master <=  1'b1;

          sda_chk <=  1'b0;

       end

     else

       begin

          cmd_ack   <=  1'b0; // default no command acknowledge + assert cmd_ack only 1clk cycle

          if (clk_en )

            case (c_state) // synopsys full_case parallel_case

              // idle state

              idle:

                begin

                   case (cmd) // synopsys full_case parallel_case

                     `I2C_CMD_START: c_state <=  start_a;

                     `I2C_CMD_STOP:  c_state <=  stop_a;

                     `I2C_CMD_WRITE: c_state <=  wr_a;

                     `I2C_CMD_READ:  c_state <=  rd_a;

                     default:        c_state <=  idle;

                   endcase

                   scl_oen_master <=  scl_oen_master; // keep SCL in same state

                   sda_oen_master <=  sda_oen_master; // keep SDA in same state

                   sda_chk <=  1'b0;    // don't check SDA output

                end

              // start

              start_a:

                begin

                   c_state <=  start_b;

                   scl_oen_master <=  scl_oen_master; // keep SCL in same state

                   sda_oen_master <=  1'b1;    // set SDA high

                   sda_chk <=  1'b0;    // don't check SDA output

                end

              start_b:

                begin

                   c_state <=  start_c;

                   scl_oen_master <=  1'b1; // set SCL high

                   sda_oen_master <=  1'b1; // keep SDA high

                   sda_chk <=  1'b0; // don't check SDA output

                end

              start_c:

                begin

                   c_state <=  start_d;

                   scl_oen_master <=  1'b1; // keep SCL high

                   sda_oen_master <=  1'b0; // set SDA low

                   sda_chk <=  1'b0; // don't check SDA output

                end

              start_d:

                begin

                   c_state <=  start_e;

                   scl_oen_master <=  1'b1; // keep SCL high

                   sda_oen_master <=  1'b0; // keep SDA low

                   sda_chk <=  1'b0; // don't check SDA output

                end

              start_e:

                begin

                   c_state <=  idle;

                   cmd_ack <=  1'b1;

                   scl_oen_master <=  1'b0; // set SCL low

                   sda_oen_master <=  1'b0; // keep SDA low

                   sda_chk <=  1'b0; // don't check SDA output

                end

              // stop

              stop_a:

                begin

                   c_state <=  stop_b;

                   scl_oen_master <=  1'b0; // keep SCL low

                   sda_oen_master <=  1'b0; // set SDA low

                   sda_chk <=  1'b0; // don't check SDA output

                end

              stop_b:

                begin

                   c_state <=  stop_c;

                   scl_oen_master <=  1'b1; // set SCL high

                   sda_oen_master <=  1'b0; // keep SDA low

                   sda_chk <=  1'b0; // don't check SDA output

                end

              stop_c:

                begin

                   c_state <=  stop_d;

                   scl_oen_master <=  1'b1; // keep SCL high

                   sda_oen_master <=  1'b0; // keep SDA low

                   sda_chk <=  1'b0; // don't check SDA output

                end

              stop_d:

                begin

                   c_state <=  idle;

                   cmd_ack <=  1'b1;

                   scl_oen_master <=  1'b1; // keep SCL high

                   sda_oen_master <=  1'b1; // set SDA high

                   sda_chk <=  1'b0; // don't check SDA output

                end

              // read

              rd_a:

                begin

                   c_state <=  rd_b;

                   scl_oen_master <=  1'b0; // keep SCL low

                   sda_oen_master <=  1'b1; // tri-state SDA

                   sda_chk <=  1'b0; // don't check SDA output

                end

              rd_b:

                begin

                   c_state <=  rd_c;

                   scl_oen_master <=  1'b1; // set SCL high

                   sda_oen_master <=  1'b1; // keep SDA tri-stated

                   sda_chk <=  1'b0; // don't check SDA output

                end

              rd_c:

                begin

                   c_state <=  rd_d;

                   scl_oen_master <=  1'b1; // keep SCL high

                   sda_oen_master <=  1'b1; // keep SDA tri-stated

                   sda_chk <=  1'b0; // don't check SDA output

                end

              rd_d:

                begin

                   c_state <=  idle;

                   cmd_ack <=  1'b1;

                   scl_oen_master <=  1'b0; // set SCL low

                   sda_oen_master <=  1'b1; // keep SDA tri-stated

                   sda_chk <=  1'b0; // don't check SDA output

                end

              // write

              wr_a:

                begin

                   c_state <=  wr_b;

                   scl_oen_master <=  1'b0; // keep SCL low

                   sda_oen_master <=  din;  // set SDA

                   sda_chk <=  1'b0; // don't check SDA output (SCL low)

                end

              wr_b:

                begin

                   c_state <=  wr_c;

                   scl_oen_master <=  1'b1; // set SCL high

                   sda_oen_master <=  din;  // keep SDA

                   sda_chk <=  1'b0; // don't check SDA output yet

                   // allow some time for SDA and SCL to settle

                end

              wr_c:

                begin

                   c_state <=  wr_d;

                   scl_oen_master <=  1'b1; // keep SCL high

                   sda_oen_master <=  din;

                   sda_chk <=  1'b1; // check SDA output

                end

              wr_d:

                begin

                   c_state <=  idle;

                   cmd_ack <=  1'b1;

                   scl_oen_master <=  1'b0; // set SCL low

                   sda_oen_master <=  din;

                   sda_chk <=  1'b0; // don't check SDA output (SCL low)

                end

            endcase

       end

   //----------Addition for slave mode...

   reg [3:0] slave_cnt;

   //The SCL can only be driven when Master mode

   assign sda_oen = master_mode ? sda_oen_master : sda_oen_slave ;

   assign scl_oen = master_mode ? scl_oen_master : scl_oen_slave ;

   reg       slave_act;

   reg       slave_adr_received_d;

   //A 1 cycle pulse slave_adr_recived is generated when a slave adress is recvied after a startcommand.

   always @(posedge clk or negedge nReset)

     if (!nReset) begin

        slave_adr <=  8'h0;

        slave_cnt <=  4'h8;

        slave_adr_received <=  1'b0;

        slave_act <=  1'b0;

     end

     else begin

        slave_adr_received <=  1'b0;

        if ((sSCL & ~dSCL) && slave_cnt != 4'h0 && slave_act)    begin

           slave_adr <=  {slave_adr[6:0], sSDA};

           slave_cnt <=  slave_cnt -1;

        end

        else if (slave_cnt == 4'h0 && !sta_condition && slave_act) begin

           slave_adr_received <=  1'b1;

           slave_act <=  1'b0;

        end

        if (sta_condition) begin

           slave_cnt <=  4'h8;

           slave_adr <=  8'h0;

           slave_adr_received <=  1'b0;

           slave_act <=  1'b1;

        end

        if(sto_condition) begin

           slave_adr_received <=  1'b0;

           slave_act <=  1'b0;

        end

     end

   parameter [4:0] slave_idle    = 5'b0_0000;

   parameter [4:0] slave_wr      = 5'b0_0001;

   parameter [4:0] slave_wr_a    = 5'b0_0010;

   parameter [4:0] slave_rd      = 5'b0_0100;

   parameter [4:0] slave_rd_a    = 5'b0_1000;

   parameter [4:0] slave_wait_next_cmd_1   = 5'b1_0000;

   parameter [4:0] slave_wait_next_cmd_2   = 5'b1_0001;

   always @(posedge clk or negedge nReset)

     if (!nReset)

       begin

          slave_state <=  slave_idle;

          cmd_slave_ack   <=  1'b0;

          sda_oen_slave   <=  1'b1;

          scl_oen_slave   <=  1'b1;

       end

     else if (rst | sta_condition || !ena)

       begin

          slave_state <=  slave_idle;

          cmd_slave_ack   <=  1'b0;

          sda_oen_slave   <=  1'b1;

          scl_oen_slave   <=  1'b1;

       end

     else

       begin

          cmd_slave_ack   <=  1'b0; // default no command acknowledge + assert cmd_ack only 1clk cycle

          if (sl_wait)

            scl_oen_slave   <=  1'b0;

          else

            scl_oen_slave   <=  1'b1;

          case (slave_state)

            slave_idle:

              begin

                 case (slave_cmd) // synopsys full_case parallel_case                             

                   `I2C_SLAVE_CMD_WRITE: slave_state <=  slave_wr;

                   `I2C_SLAVE_CMD_READ:

                     begin

                        slave_state <=  slave_rd;