OpenCores
URL https://opencores.org/ocsvn/zipcpu/zipcpu/trunk

Subversion Repositories zipcpu

[/] [zipcpu/] [trunk/] [rtl/] [core/] [zipcpu.v] - Blame information for rev 140

Go to most recent revision | Details | Compare with Previous | View Log

Line No. Rev Author Line
1 2 dgisselq
///////////////////////////////////////////////////////////////////////////////
2
//
3
// Filename:    zipcpu.v
4
//
5
// Project:     Zip CPU -- a small, lightweight, RISC CPU soft core
6
//
7
// Purpose:     This is the top level module holding the core of the Zip CPU
8
//              together.  The Zip CPU is designed to be as simple as possible.
9 56 dgisselq
//      (actual implementation aside ...)  The instruction set is about as
10
//      RISC as you can get, there are only 16 instruction types supported.
11
//      Please see the accompanying spec.pdf file for a description of these
12
//      instructions.
13 2 dgisselq
//
14 56 dgisselq
//      All instructions are 32-bits wide.  All bus accesses, both address and
15
//      data, are 32-bits over a wishbone bus.
16 2 dgisselq
//
17
//      The Zip CPU is fully pipelined with the following pipeline stages:
18
//
19 56 dgisselq
//              1. Prefetch, returns the instruction from memory. 
20 2 dgisselq
//
21
//              2. Instruction Decode
22
//
23
//              3. Read Operands
24
//
25
//              4. Apply Instruction
26
//
27
//              4. Write-back Results
28
//
29 56 dgisselq
//      Further information about the inner workings of this CPU may be
30
//      found in the spec.pdf file.  (The documentation within this file
31
//      had become out of date and out of sync with the spec.pdf, so look
32
//      to the spec.pdf for accurate and up to date information.)
33 2 dgisselq
//
34
//
35 69 dgisselq
//      In general, the pipelining is controlled by three pieces of logic
36
//      per stage: _ce, _stall, and _valid.  _valid means that the stage
37
//      holds a valid instruction.  _ce means that the instruction from the
38
//      previous stage is to move into this one, and _stall means that the
39
//      instruction from the previous stage may not move into this one.
40
//      The difference between these control signals allows individual stages
41
//      to propagate instructions independently.  In general, the logic works
42
//      as:
43
//
44
//
45
//      assign  (n)_ce = (n-1)_valid && (~(n)_stall)
46
//
47
//
48
//      always @(posedge i_clk)
49
//              if ((i_rst)||(clear_pipeline))
50
//                      (n)_valid = 0
51
//              else if (n)_ce
52
//                      (n)_valid = 1
53
//              else if (n+1)_ce
54
//                      (n)_valid = 0
55
//
56
//      assign (n)_stall = (  (n-1)_valid && ( pipeline hazard detection )  )
57
//                      || (  (n)_valid && (n+1)_stall );
58
//
59
//      and ...
60
//
61
//      always @(posedge i_clk)
62
//              if (n)_ce
63
//                      (n)_variable = ... whatever logic for this stage
64
//
65
//      Note that a stage can stall even if no instruction is loaded into
66
//      it.
67
//
68
//
69 2 dgisselq
// Creator:     Dan Gisselquist, Ph.D.
70 69 dgisselq
//              Gisselquist Technology, LLC
71 2 dgisselq
//
72
///////////////////////////////////////////////////////////////////////////////
73
//
74
// Copyright (C) 2015, Gisselquist Technology, LLC
75
//
76
// This program is free software (firmware): you can redistribute it and/or
77
// modify it under the terms of  the GNU General Public License as published
78
// by the Free Software Foundation, either version 3 of the License, or (at
79
// your option) any later version.
80
//
81
// This program is distributed in the hope that it will be useful, but WITHOUT
82
// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
83
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
84
// for more details.
85
//
86
// License:     GPL, v3, as defined and found on www.gnu.org,
87
//              http://www.gnu.org/licenses/gpl.html
88
//
89
//
90
///////////////////////////////////////////////////////////////////////////////
91
//
92 36 dgisselq
// We can either pipeline our fetches, or issue one fetch at a time.  Pipelined
93
// fetches are more complicated and therefore use more FPGA resources, while
94
// single fetches will cause the CPU to stall for about 5 stalls each 
95
// instruction cycle, effectively reducing the instruction count per clock to
96
// about 0.2.  However, the area cost may be worth it.  Consider:
97
//
98
//      Slice LUTs              ZipSystem       ZipCPU
99
//      Single Fetching         2521            1734
100
//      Pipelined fetching      2796            2046
101
//
102
//
103
//
104 25 dgisselq
`define CPU_CC_REG      4'he
105 2 dgisselq
`define CPU_PC_REG      4'hf
106 69 dgisselq
`define CPU_FPUERR_BIT  12      // Floating point error flag, set on error
107
`define CPU_DIVERR_BIT  11      // Divide error flag, set on divide by zero
108
`define CPU_BUSERR_BIT  10      // Bus error flag, set on error
109
`define CPU_TRAP_BIT    9       // User TRAP has taken place
110
`define CPU_ILL_BIT     8       // Illegal instruction
111 2 dgisselq
`define CPU_BREAK_BIT   7
112 69 dgisselq
`define CPU_STEP_BIT    6       // Will step one or two (VLIW) instructions
113 2 dgisselq
`define CPU_GIE_BIT     5
114
`define CPU_SLEEP_BIT   4
115 36 dgisselq
// Compile time defines
116 56 dgisselq
//
117
`include "cpudefs.v"
118
//
119 65 dgisselq
//
120 2 dgisselq
module  zipcpu(i_clk, i_rst, i_interrupt,
121
                // Debug interface
122 18 dgisselq
                i_halt, i_clear_pf_cache, i_dbg_reg, i_dbg_we, i_dbg_data,
123
                        o_dbg_stall, o_dbg_reg, o_dbg_cc,
124 2 dgisselq
                        o_break,
125
                // CPU interface to the wishbone bus
126 36 dgisselq
                o_wb_gbl_cyc, o_wb_gbl_stb,
127
                        o_wb_lcl_cyc, o_wb_lcl_stb,
128
                        o_wb_we, o_wb_addr, o_wb_data,
129 2 dgisselq
                        i_wb_ack, i_wb_stall, i_wb_data,
130 36 dgisselq
                        i_wb_err,
131 2 dgisselq
                // Accounting/CPU usage interface
132 65 dgisselq
                o_op_stall, o_pf_stall, o_i_count
133
`ifdef  DEBUG_SCOPE
134
                , o_debug
135
`endif
136
                );
137 48 dgisselq
        parameter       RESET_ADDRESS=32'h0100000, ADDRESS_WIDTH=24,
138 69 dgisselq
                        LGICACHE=6;
139 56 dgisselq
`ifdef  OPT_MULTIPLY
140 132 dgisselq
        parameter       IMPLEMENT_MPY = `OPT_MULTIPLY;
141 56 dgisselq
`else
142
        parameter       IMPLEMENT_MPY = 0;
143
`endif
144 71 dgisselq
`ifdef  OPT_DIVIDE
145
        parameter       IMPLEMENT_DIVIDE = 1;
146
`else
147
        parameter       IMPLEMENT_DIVIDE = 0;
148
`endif
149
`ifdef  OPT_IMPLEMENT_FPU
150
        parameter       IMPLEMENT_FPU = 1,
151
`else
152
        parameter       IMPLEMENT_FPU = 0,
153
`endif
154 69 dgisselq
                        IMPLEMENT_LOCK=1;
155
`ifdef  OPT_EARLY_BRANCHING
156
        parameter       EARLY_BRANCHING = 1;
157
`else
158
        parameter       EARLY_BRANCHING = 0;
159
`endif
160
        parameter       AW=ADDRESS_WIDTH;
161 2 dgisselq
        input                   i_clk, i_rst, i_interrupt;
162
        // Debug interface -- inputs
163 18 dgisselq
        input                   i_halt, i_clear_pf_cache;
164 2 dgisselq
        input           [4:0]    i_dbg_reg;
165
        input                   i_dbg_we;
166
        input           [31:0]   i_dbg_data;
167
        // Debug interface -- outputs
168
        output  reg             o_dbg_stall;
169
        output  reg     [31:0]   o_dbg_reg;
170 56 dgisselq
        output  reg     [3:0]    o_dbg_cc;
171 2 dgisselq
        output  wire            o_break;
172
        // Wishbone interface -- outputs
173 36 dgisselq
        output  wire            o_wb_gbl_cyc, o_wb_gbl_stb;
174
        output  wire            o_wb_lcl_cyc, o_wb_lcl_stb, o_wb_we;
175 48 dgisselq
        output  wire    [(AW-1):0]       o_wb_addr;
176
        output  wire    [31:0]   o_wb_data;
177 2 dgisselq
        // Wishbone interface -- inputs
178
        input                   i_wb_ack, i_wb_stall;
179
        input           [31:0]   i_wb_data;
180 36 dgisselq
        input                   i_wb_err;
181 2 dgisselq
        // Accounting outputs ... to help us count stalls and usage
182 9 dgisselq
        output  wire            o_op_stall;
183 2 dgisselq
        output  wire            o_pf_stall;
184 9 dgisselq
        output  wire            o_i_count;
185 56 dgisselq
        //
186 65 dgisselq
`ifdef  DEBUG_SCOPE
187 56 dgisselq
        output  reg     [31:0]   o_debug;
188 65 dgisselq
`endif
189 2 dgisselq
 
190 25 dgisselq
 
191 2 dgisselq
        // Registers
192 56 dgisselq
        //
193
        //      The distributed RAM style comment is necessary on the
194
        // SPARTAN6 with XST to prevent XST from oversimplifying the register
195
        // set and in the process ruining everything else.  It basically
196
        // optimizes logic away, to where it no longer works.  The logic
197
        // as described herein will work, this just makes sure XST implements
198
        // that logic.
199
        //
200
        (* ram_style = "distributed" *)
201 2 dgisselq
        reg     [31:0]   regset [0:31];
202 9 dgisselq
 
203
        // Condition codes
204 56 dgisselq
        // (BUS, TRAP,ILL,BREAKEN,STEP,GIE,SLEEP ), V, N, C, Z
205
        reg     [3:0]    flags, iflags;
206 83 dgisselq
        wire    [13:0]   w_uflags, w_iflags;
207 25 dgisselq
        reg             trap, break_en, step, gie, sleep;
208 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
209 65 dgisselq
        reg             ill_err_u, ill_err_i;
210 38 dgisselq
`else
211 65 dgisselq
        wire            ill_err_u, ill_err_i;
212 36 dgisselq
`endif
213 65 dgisselq
        reg             ibus_err_flag, ubus_err_flag;
214 69 dgisselq
        wire            idiv_err_flag, udiv_err_flag;
215
        wire            ifpu_err_flag, ufpu_err_flag;
216
        wire            ihalt_phase, uhalt_phase;
217 2 dgisselq
 
218 9 dgisselq
        // The master chip enable
219
        wire            master_ce;
220 2 dgisselq
 
221
        //
222
        //
223
        //      PIPELINE STAGE #1 :: Prefetch
224
        //              Variable declarations
225
        //
226 48 dgisselq
        reg     [(AW-1):0]       pf_pc;
227 69 dgisselq
        reg     new_pc;
228 18 dgisselq
        wire    clear_pipeline;
229 69 dgisselq
        assign  clear_pipeline = new_pc || i_clear_pf_cache;
230 9 dgisselq
 
231
        wire            dcd_stalled;
232 36 dgisselq
        wire            pf_cyc, pf_stb, pf_we, pf_busy, pf_ack, pf_stall, pf_err;
233 48 dgisselq
        wire    [(AW-1):0]       pf_addr;
234
        wire    [31:0]           pf_data;
235
        wire    [31:0]           instruction;
236
        wire    [(AW-1):0]       instruction_pc;
237 36 dgisselq
        wire    pf_valid, instruction_gie, pf_illegal;
238 2 dgisselq
 
239
        //
240
        //
241
        //      PIPELINE STAGE #2 :: Instruction Decode
242
        //              Variable declarations
243
        //
244
        //
245 83 dgisselq
        reg             opvalid, opvalid_mem, opvalid_alu;
246 69 dgisselq
        reg             opvalid_div, opvalid_fpu;
247
        wire            op_stall, dcd_ce, dcd_phase;
248
        wire    [3:0]    dcdOp;
249
        wire    [4:0]    dcdA, dcdB, dcdR;
250
        wire            dcdA_cc, dcdB_cc, dcdA_pc, dcdB_pc, dcdR_cc, dcdR_pc;
251
        wire    [3:0]    dcdF;
252
        wire            dcdR_wr, dcdA_rd, dcdB_rd,
253
                                dcdALU, dcdM, dcdDV, dcdFP,
254 71 dgisselq
                                dcdF_wr, dcd_gie, dcd_break, dcd_lock,
255 105 dgisselq
                                dcd_pipe, dcd_ljmp;
256 69 dgisselq
        reg             r_dcdvalid;
257
        wire            dcdvalid;
258
        wire    [(AW-1):0]       dcd_pc;
259
        wire    [31:0]   dcdI;
260
        wire            dcd_zI; // true if dcdI == 0
261 2 dgisselq
        wire    dcdA_stall, dcdB_stall, dcdF_stall;
262
 
263 69 dgisselq
        wire    dcd_illegal;
264
        wire                    dcd_early_branch;
265 48 dgisselq
        wire    [(AW-1):0]       dcd_branch_pc;
266 2 dgisselq
 
267
 
268
        //
269
        //
270
        //      PIPELINE STAGE #3 :: Read Operands
271
        //              Variable declarations
272
        //
273
        //
274
        //
275
        // Now, let's read our operands
276
        reg     [4:0]    alu_reg;
277
        reg     [3:0]    opn;
278
        reg     [4:0]    opR;
279 48 dgisselq
        reg     [31:0]   r_opA, r_opB;
280
        reg     [(AW-1):0]       op_pc;
281 25 dgisselq
        wire    [31:0]   w_opA, w_opB;
282 2 dgisselq
        wire    [31:0]   opA_nowait, opB_nowait, opA, opB;
283 56 dgisselq
        reg             opR_wr, opR_cc, opF_wr, op_gie;
284 83 dgisselq
        wire    [13:0]   opFl;
285 56 dgisselq
        reg     [5:0]    r_opF;
286
        wire    [7:0]    opF;
287 132 dgisselq
        wire            op_ce, op_phase, op_pipe;
288 56 dgisselq
        // Some pipeline control wires
289 69 dgisselq
`ifdef  OPT_PIPELINED
290 56 dgisselq
        reg     opA_alu, opA_mem;
291
        reg     opB_alu, opB_mem;
292
`endif
293 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
294 36 dgisselq
        reg     op_illegal;
295
`endif
296 69 dgisselq
        reg     op_break;
297
        wire    op_lock;
298 2 dgisselq
 
299
 
300
        //
301
        //
302
        //      PIPELINE STAGE #4 :: ALU / Memory
303
        //              Variable declarations
304
        //
305
        //
306 48 dgisselq
        reg     [(AW-1):0]       alu_pc;
307 132 dgisselq
        reg             alu_pc_valid, mem_pc_valid;
308 69 dgisselq
        wire            alu_phase;
309 2 dgisselq
        wire            alu_ce, alu_stall;
310
        wire    [31:0]   alu_result;
311
        wire    [3:0]    alu_flags;
312 71 dgisselq
        wire            alu_valid, alu_busy;
313 2 dgisselq
        wire            set_cond;
314
        reg             alu_wr, alF_wr, alu_gie;
315 56 dgisselq
        wire            alu_illegal_op;
316 38 dgisselq
        wire            alu_illegal;
317 2 dgisselq
 
318
 
319
 
320
        wire    mem_ce, mem_stalled;
321 38 dgisselq
`ifdef  OPT_PIPELINED_BUS_ACCESS
322
        wire    mem_pipe_stalled;
323
`endif
324 36 dgisselq
        wire    mem_valid, mem_ack, mem_stall, mem_err, bus_err,
325
                mem_cyc_gbl, mem_cyc_lcl, mem_stb_gbl, mem_stb_lcl, mem_we;
326 48 dgisselq
        wire    [4:0]            mem_wreg;
327 9 dgisselq
 
328 48 dgisselq
        wire                    mem_busy, mem_rdbusy;
329
        wire    [(AW-1):0]       mem_addr;
330
        wire    [31:0]           mem_data, mem_result;
331 2 dgisselq
 
332 69 dgisselq
        wire    div_ce, div_error, div_busy, div_valid;
333
        wire    [31:0]   div_result;
334
        wire    [3:0]    div_flags;
335 2 dgisselq
 
336 69 dgisselq
        assign  div_ce = (master_ce)&&(~clear_pipeline)&&(opvalid_div)
337
                                &&(~mem_rdbusy)&&(~div_busy)&&(~fpu_busy)
338
                                &&(set_cond);
339 2 dgisselq
 
340 69 dgisselq
        wire    fpu_ce, fpu_error, fpu_busy, fpu_valid;
341
        wire    [31:0]   fpu_result;
342
        wire    [3:0]    fpu_flags;
343
 
344
        assign  fpu_ce = (master_ce)&&(~clear_pipeline)&&(opvalid_fpu)
345
                                &&(~mem_rdbusy)&&(~div_busy)&&(~fpu_busy)
346
                                &&(set_cond);
347
 
348
 
349 2 dgisselq
        //
350
        //
351
        //      PIPELINE STAGE #5 :: Write-back
352
        //              Variable declarations
353
        //
354 25 dgisselq
        wire            wr_reg_ce, wr_flags_ce, wr_write_pc, wr_write_cc;
355 2 dgisselq
        wire    [4:0]    wr_reg_id;
356
        wire    [31:0]   wr_reg_vl;
357
        wire    w_switch_to_interrupt, w_release_from_interrupt;
358 48 dgisselq
        reg     [(AW-1):0]       upc, ipc;
359 2 dgisselq
 
360
 
361
 
362
        //
363
        //      MASTER: clock enable.
364
        //
365 38 dgisselq
        assign  master_ce = (~i_halt)&&(~o_break)&&(~sleep);
366 2 dgisselq
 
367
 
368
        //
369
        //      PIPELINE STAGE #1 :: Prefetch
370
        //              Calculate stall conditions
371 65 dgisselq
        //
372
        //      These are calculated externally, within the prefetch module.
373
        //
374 2 dgisselq
 
375
        //
376
        //      PIPELINE STAGE #2 :: Instruction Decode
377
        //              Calculate stall conditions
378 69 dgisselq
`ifdef  OPT_PIPELINED
379
        assign          dcd_ce = ((~dcdvalid)||(~dcd_stalled))&&(~clear_pipeline);
380
`else
381
        assign          dcd_ce = 1'b1;
382
`endif
383
`ifdef  OPT_PIPELINED
384
        assign          dcd_stalled = (dcdvalid)&&(op_stall);
385
`else
386
        // If not pipelined, there will be no opvalid_ anything, and the
387
        // op_stall will be false, dcdX_stall will be false, thus we can simply
388
        // do a ...
389
        assign          dcd_stalled = 1'b0;
390
`endif
391 2 dgisselq
        //
392
        //      PIPELINE STAGE #3 :: Read Operands
393
        //              Calculate stall conditions
394 69 dgisselq
        wire    op_lock_stall;
395
`ifdef  OPT_PIPELINED
396
        assign  op_stall = (opvalid)&&( // Only stall if we're loaded w/validins
397
                        // Stall if we're stopped, and not allowed to execute
398
                        // an instruction
399
                        // (~master_ce)         // Already captured in alu_stall
400
                        //
401 56 dgisselq
                        // Stall if going into the ALU and the ALU is stalled
402
                        //      i.e. if the memory is busy, or we are single
403 69 dgisselq
                        //      stepping.  This also includes our stalls for
404
                        //      op_break and op_lock, so we don't need to
405
                        //      include those as well here.
406 83 dgisselq
                        // This also includes whether or not the divide or
407
                        // floating point units are busy.
408
                        (alu_stall)
409 56 dgisselq
                        //
410
                        // Stall if we are going into memory with an operation
411
                        //      that cannot be pipelined, and the memory is
412
                        //      already busy
413 83 dgisselq
                        ||(mem_stalled) // &&(opvalid_mem) part of mem_stalled
414 69 dgisselq
                        )
415
                        ||(dcdvalid)&&(
416 71 dgisselq
                                // Stall if we need to wait for an operand A
417 69 dgisselq
                                // to be ready to read
418 71 dgisselq
                                (dcdA_stall)
419 69 dgisselq
                                // Likewise for B, also includes logic
420
                                // regarding immediate offset (register must
421
                                // be in register file if we need to add to
422
                                // an immediate)
423
                                ||(dcdB_stall)
424
                                // Or if we need to wait on flags to work on the
425
                                // CC register
426
                                ||(dcdF_stall)
427
                        );
428 71 dgisselq
        assign  op_ce = ((dcdvalid)||(dcd_illegal))&&(~op_stall)&&(~clear_pipeline);
429 65 dgisselq
`else
430 69 dgisselq
        assign  op_stall = (opvalid)&&(~master_ce);
431 71 dgisselq
        assign  op_ce = ((dcdvalid)||(dcd_illegal));
432 65 dgisselq
`endif
433 2 dgisselq
 
434
        //
435
        //      PIPELINE STAGE #4 :: ALU / Memory
436
        //              Calculate stall conditions
437 36 dgisselq
        //
438
        // 1. Basic stall is if the previous stage is valid and the next is
439
        //      busy.  
440
        // 2. Also stall if the prior stage is valid and the master clock enable
441
        //      is de-selected
442 56 dgisselq
        // 3. Stall if someone on the other end is writing the CC register,
443
        //      since we don't know if it'll put us to sleep or not.
444 36 dgisselq
        // 4. Last case: Stall if we would otherwise move a break instruction
445
        //      through the ALU.  Break instructions are not allowed through
446
        //      the ALU.
447 69 dgisselq
`ifdef  OPT_PIPELINED
448 71 dgisselq
        assign  alu_stall = (((~master_ce)||(mem_rdbusy)||(alu_busy))&&(opvalid_alu)) //Case 1&2
449 56 dgisselq
                        // Old case #3--this isn't an ALU stall though ...
450
                        ||((opvalid_alu)&&(wr_reg_ce)&&(wr_reg_id[4] == op_gie)
451
                                &&(wr_write_cc)) // Case 3
452 69 dgisselq
                        ||((opvalid)&&(op_lock)&&(op_lock_stall))
453
                        ||((opvalid)&&(op_break))
454
                        ||(div_busy)||(fpu_busy);
455 71 dgisselq
        assign  alu_ce = (master_ce)&&((opvalid_alu)||(op_illegal))
456 69 dgisselq
                                &&(~alu_stall)
457
                                &&(~clear_pipeline);
458
`else
459
        assign  alu_stall = ((~master_ce)&&(opvalid_alu))
460
                                ||((opvalid_alu)&&(op_break));
461 71 dgisselq
        assign  alu_ce = (master_ce)&&((opvalid_alu)||(op_illegal))&&(~alu_stall);
462 69 dgisselq
`endif
463 2 dgisselq
        //
464 65 dgisselq
 
465
        //
466
        // Note: if you change the conditions for mem_ce, you must also change
467
        // alu_pc_valid.
468
        //
469 69 dgisselq
`ifdef  OPT_PIPELINED
470
        assign  mem_ce = (master_ce)&&(opvalid_mem)&&(~mem_stalled)
471 71 dgisselq
                        &&(~clear_pipeline);
472 69 dgisselq
`else
473
        // If we aren't pipelined, then no one will be changing what's in the
474
        // pipeline (i.e. clear_pipeline), while our only instruction goes
475
        // through the ... pipeline.
476 71 dgisselq
        assign  mem_ce = (master_ce)&&(opvalid_mem)&&(~mem_stalled);
477 69 dgisselq
`endif
478 65 dgisselq
`ifdef  OPT_PIPELINED_BUS_ACCESS
479 71 dgisselq
        assign  mem_stalled = (~master_ce)||(alu_busy)||((opvalid_mem)&&(
480 38 dgisselq
                                (mem_pipe_stalled)
481
                                ||((~op_pipe)&&(mem_busy))
482 69 dgisselq
                                ||(div_busy)
483
                                ||(fpu_busy)
484 38 dgisselq
                                // Stall waiting for flags to be valid
485
                                // Or waiting for a write to the PC register
486
                                // Or CC register, since that can change the
487
                                //  PC as well
488
                                ||((wr_reg_ce)&&(wr_reg_id[4] == op_gie)
489
                                        &&((wr_write_pc)||(wr_write_cc)))));
490
`else
491 69 dgisselq
`ifdef  OPT_PIPELINED
492 25 dgisselq
        assign  mem_stalled = (mem_busy)||((opvalid_mem)&&(
493 2 dgisselq
                                (~master_ce)
494
                                // Stall waiting for flags to be valid
495
                                // Or waiting for a write to the PC register
496 25 dgisselq
                                // Or CC register, since that can change the
497
                                //  PC as well
498
                                ||((wr_reg_ce)&&(wr_reg_id[4] == op_gie)&&((wr_write_pc)||(wr_write_cc)))));
499 69 dgisselq
`else
500
        assign  mem_stalled = (opvalid_mem)&&(~master_ce);
501 38 dgisselq
`endif
502 69 dgisselq
`endif
503 2 dgisselq
 
504
 
505
        //
506
        //
507
        //      PIPELINE STAGE #1 :: Prefetch
508
        //
509
        //
510 38 dgisselq
`ifdef  OPT_SINGLE_FETCH
511 9 dgisselq
        wire            pf_ce;
512
 
513 69 dgisselq
        assign          pf_ce = (~pf_valid)&&(~dcdvalid)&&(~opvalid)&&(~alu_valid);
514 48 dgisselq
        prefetch        #(ADDRESS_WIDTH)
515 69 dgisselq
                        pf(i_clk, i_rst, (pf_ce), (~dcd_stalled), pf_pc, gie,
516 2 dgisselq
                                instruction, instruction_pc, instruction_gie,
517 36 dgisselq
                                        pf_valid, pf_illegal,
518
                                pf_cyc, pf_stb, pf_we, pf_addr, pf_data,
519
                                pf_ack, pf_stall, pf_err, i_wb_data);
520 69 dgisselq
 
521
        initial r_dcdvalid = 1'b0;
522
        always @(posedge i_clk)
523
                if (i_rst)
524
                        r_dcdvalid <= 1'b0;
525
                else if (dcd_ce)
526 105 dgisselq
                        r_dcdvalid <= (pf_valid);
527
                else if (op_ce)
528 69 dgisselq
                        r_dcdvalid <= 1'b0;
529
        assign  dcdvalid = r_dcdvalid;
530
 
531 2 dgisselq
`else // Pipe fetch
532 69 dgisselq
 
533
`ifdef  OPT_TRADITIONAL_PFCACHE
534
        pfcache #(LGICACHE, ADDRESS_WIDTH)
535 105 dgisselq
                pf(i_clk, i_rst, (new_pc)||((dcd_early_branch)&&(~clear_pipeline)),
536 69 dgisselq
                                        i_clear_pf_cache,
537
                                // dcd_pc,
538
                                ~dcd_stalled,
539 105 dgisselq
                                ((dcd_early_branch)&&(~clear_pipeline))
540 69 dgisselq
                                        ? dcd_branch_pc:pf_pc,
541
                                instruction, instruction_pc, pf_valid,
542
                                pf_cyc, pf_stb, pf_we, pf_addr, pf_data,
543
                                        pf_ack, pf_stall, pf_err, i_wb_data,
544
                                pf_illegal);
545
`else
546 48 dgisselq
        pipefetch       #(RESET_ADDRESS, LGICACHE, ADDRESS_WIDTH)
547 105 dgisselq
                        pf(i_clk, i_rst, (new_pc)||((dcd_early_branch)&&(~clear_pipeline)),
548 36 dgisselq
                                        i_clear_pf_cache, ~dcd_stalled,
549
                                        (new_pc)?pf_pc:dcd_branch_pc,
550 2 dgisselq
                                        instruction, instruction_pc, pf_valid,
551
                                pf_cyc, pf_stb, pf_we, pf_addr, pf_data,
552 36 dgisselq
                                        pf_ack, pf_stall, pf_err, i_wb_data,
553 69 dgisselq
//`ifdef        OPT_PRECLEAR_BUS
554
                                //((dcd_clear_bus)&&(dcdvalid))
555
                                //||((op_clear_bus)&&(opvalid))
556
                                //||
557
//`endif
558 36 dgisselq
                                (mem_cyc_lcl)||(mem_cyc_gbl),
559
                                pf_illegal);
560 69 dgisselq
`endif
561 2 dgisselq
        assign  instruction_gie = gie;
562
 
563 69 dgisselq
        initial r_dcdvalid = 1'b0;
564 2 dgisselq
        always @(posedge i_clk)
565 69 dgisselq
                if ((i_rst)||(clear_pipeline))
566
                        r_dcdvalid <= 1'b0;
567 2 dgisselq
                else if (dcd_ce)
568 105 dgisselq
                        r_dcdvalid <= (pf_valid)&&(~clear_pipeline)&&(~dcd_ljmp)&&((~r_dcdvalid)||(~dcd_early_branch));
569 69 dgisselq
                else if (op_ce)
570
                        r_dcdvalid <= 1'b0;
571
        assign  dcdvalid = r_dcdvalid;
572 36 dgisselq
`endif
573 2 dgisselq
 
574 69 dgisselq
`ifdef  OPT_NEW_INSTRUCTION_SET
575
        idecode #(AW, IMPLEMENT_MPY, EARLY_BRANCHING, IMPLEMENT_DIVIDE,
576
                        IMPLEMENT_FPU)
577
                instruction_decoder(i_clk, (i_rst)||(clear_pipeline),
578
                        dcd_ce, dcd_stalled, instruction, instruction_gie,
579
                        instruction_pc, pf_valid, pf_illegal, dcd_phase,
580
                        dcd_illegal, dcd_pc, dcd_gie,
581
                        { dcdR_cc, dcdR_pc, dcdR },
582
                        { dcdA_cc, dcdA_pc, dcdA },
583
                        { dcdB_cc, dcdB_pc, dcdB },
584
                        dcdI, dcd_zI, dcdF, dcdF_wr, dcdOp,
585
                        dcdALU, dcdM, dcdDV, dcdFP, dcd_break, dcd_lock,
586
                        dcdR_wr,dcdA_rd, dcdB_rd,
587
                        dcd_early_branch,
588 105 dgisselq
                        dcd_branch_pc, dcd_ljmp,
589 71 dgisselq
                        dcd_pipe);
590 36 dgisselq
`else
591 69 dgisselq
        idecode_deprecated
592
                #(AW, IMPLEMENT_MPY, EARLY_BRANCHING, IMPLEMENT_DIVIDE,
593
                        IMPLEMENT_FPU)
594
                instruction_decoder(i_clk, (i_rst)||(clear_pipeline),
595
                        dcd_ce, dcd_stalled, instruction, instruction_gie,
596
                        instruction_pc, pf_valid, pf_illegal, dcd_phase,
597
                        dcd_illegal, dcd_pc, dcd_gie,
598
                        { dcdR_cc, dcdR_pc, dcdR },
599
                        { dcdA_cc, dcdA_pc, dcdA },
600
                        { dcdB_cc, dcdB_pc, dcdB },
601
                        dcdI, dcd_zI, dcdF, dcdF_wr, dcdOp,
602
                        dcdALU, dcdM, dcdDV, dcdFP, dcd_break, dcd_lock,
603
                        dcdR_wr,dcdA_rd, dcdB_rd,
604
                        dcd_early_branch,
605 71 dgisselq
                        dcd_branch_pc,
606
                        dcd_pipe);
607 105 dgisselq
        assign  dcd_ljmp = 1'b0;
608 36 dgisselq
`endif
609 2 dgisselq
 
610 38 dgisselq
`ifdef  OPT_PIPELINED_BUS_ACCESS
611 132 dgisselq
        reg             r_op_pipe;
612 2 dgisselq
 
613 132 dgisselq
        initial r_op_pipe = 1'b0;
614 38 dgisselq
        // To be a pipeable operation, there must be 
615
        //      two valid adjacent instructions
616
        //      Both must be memory instructions
617
        //      Both must be writes, or both must be reads
618
        //      Both operations must be to the same identical address,
619
        //              or at least a single (one) increment above that address
620 71 dgisselq
        //
621
        // However ... we need to know this before this clock, hence this is
622
        // calculated in the instruction decoder.
623 38 dgisselq
        always @(posedge i_clk)
624
                if (op_ce)
625 132 dgisselq
                        r_op_pipe <= dcd_pipe;
626
        assign  op_pipe = r_op_pipe;
627
`else
628
        assign  op_pipe = 1'b0;
629 38 dgisselq
`endif
630
 
631 2 dgisselq
        //
632
        //
633
        //      PIPELINE STAGE #3 :: Read Operands (Registers)
634
        //
635
        //
636 25 dgisselq
        assign  w_opA = regset[dcdA];
637
        assign  w_opB = regset[dcdB];
638 56 dgisselq
 
639 132 dgisselq
        wire    [8:0]    w_cpu_info;
640
        assign  w_cpu_info = {
641
`ifdef  OPT_ILLEGAL_INSTRUCTION
642
        1'b1,
643
`else
644
        1'b0,
645
`endif
646
`ifdef  OPT_MULTIPLY
647
        1'b1,
648
`else
649
        1'b0,
650
`endif
651
`ifdef  OPT_DIVIDE
652
        1'b1,
653
`else
654
        1'b0,
655
`endif
656
`ifdef  OPT_IMPLEMENT_FPU
657
        1'b1,
658
`else
659
        1'b0,
660
`endif
661
`ifdef  OPT_PIPELINED
662
        1'b1,
663
`else
664
        1'b0,
665
`endif
666
`ifdef  OPT_TRADITIONAL_CACHE
667
        1'b1,
668
`else
669
        1'b0,
670
`endif
671
`ifdef  OPT_EARLY_BRANCHING
672
        1'b1,
673
`else
674
        1'b0,
675
`endif
676
`ifdef  OPT_PIPELINED_BUS_ACCESS
677
        1'b1,
678
`else
679
        1'b0,
680
`endif
681
`ifdef  OPT_VLIW
682
        1'b1
683
`else
684
        1'b0
685
`endif
686
        };
687
 
688 56 dgisselq
        wire    [31:0]   w_pcA_v;
689
        generate
690
        if (AW < 32)
691
                assign  w_pcA_v = {{(32-AW){1'b0}}, (dcdA[4] == dcd_gie)?dcd_pc:upc };
692
        else
693
                assign  w_pcA_v = (dcdA[4] == dcd_gie)?dcd_pc:upc;
694
        endgenerate
695 71 dgisselq
 
696
`ifdef  OPT_PIPELINED
697
        reg     [4:0]    opA_id, opB_id;
698
        reg             opA_rd, opB_rd;
699 2 dgisselq
        always @(posedge i_clk)
700 71 dgisselq
                if (op_ce)
701
                begin
702
                        opA_id <= dcdA;
703
                        opB_id <= dcdB;
704
                        opA_rd <= dcdA_rd;
705
                        opB_rd <= dcdB_rd;
706
                end
707
`endif
708
 
709
        always @(posedge i_clk)
710 2 dgisselq
                if (op_ce) // &&(dcdvalid))
711
                begin
712
                        if ((wr_reg_ce)&&(wr_reg_id == dcdA))
713
                                r_opA <= wr_reg_vl;
714 25 dgisselq
                        else if (dcdA_pc)
715 56 dgisselq
                                r_opA <= w_pcA_v;
716 25 dgisselq
                        else if (dcdA_cc)
717 132 dgisselq
                                r_opA <= { w_cpu_info, w_opA[22:14], (dcdA[4])?w_uflags:w_iflags };
718 2 dgisselq
                        else
719 25 dgisselq
                                r_opA <= w_opA;
720 69 dgisselq
`ifdef  OPT_PIPELINED
721 71 dgisselq
                end else
722 48 dgisselq
                begin // We were going to pick these up when they became valid,
723
                        // but for some reason we're stuck here as they became
724
                        // valid.  Pick them up now anyway
725 71 dgisselq
                        // if (((opA_alu)&&(alu_wr))||((opA_mem)&&(mem_valid)))
726
                                // r_opA <= wr_reg_vl;
727
                        if ((wr_reg_ce)&&(wr_reg_id == opA_id)&&(opA_rd))
728 48 dgisselq
                                r_opA <= wr_reg_vl;
729 56 dgisselq
`endif
730 2 dgisselq
                end
731 56 dgisselq
 
732 69 dgisselq
        wire    [31:0]   w_opBnI, w_pcB_v;
733 56 dgisselq
        generate
734
        if (AW < 32)
735
                assign  w_pcB_v = {{(32-AW){1'b0}}, (dcdB[4] == dcd_gie)?dcd_pc:upc };
736
        else
737
                assign  w_pcB_v = (dcdB[4] == dcd_gie)?dcd_pc:upc;
738
        endgenerate
739
 
740 36 dgisselq
        assign  w_opBnI = (~dcdB_rd) ? 32'h00
741 56 dgisselq
                : (((wr_reg_ce)&&(wr_reg_id == dcdB)) ? wr_reg_vl
742
                : ((dcdB_pc) ? w_pcB_v
743 132 dgisselq
                : ((dcdB_cc) ? { w_cpu_info, w_opB[22:14], // w_opB[31:14],
744
                        (dcdB[4])?w_uflags:w_iflags}
745 56 dgisselq
                : w_opB)));
746
 
747 2 dgisselq
        always @(posedge i_clk)
748
                if (op_ce) // &&(dcdvalid))
749 36 dgisselq
                        r_opB <= w_opBnI + dcdI;
750 69 dgisselq
`ifdef  OPT_PIPELINED
751 71 dgisselq
                else if ((wr_reg_ce)&&(opB_id == wr_reg_id)&&(opB_rd))
752 48 dgisselq
                        r_opB <= wr_reg_vl;
753 56 dgisselq
`endif
754 2 dgisselq
 
755
        // The logic here has become more complex than it should be, no thanks
756
        // to Xilinx's Vivado trying to help.  The conditions are supposed to
757
        // be two sets of four bits: the top bits specify what bits matter, the
758
        // bottom specify what those top bits must equal.  However, two of
759
        // conditions check whether bits are on, and those are the only two
760
        // conditions checking those bits.  Therefore, Vivado complains that
761
        // these two bits are redundant.  Hence the convoluted expression
762
        // below, arriving at what we finally want in the (now wire net)
763
        // opF.
764
        always @(posedge i_clk)
765
                if (op_ce)
766 36 dgisselq
                begin // Set the flag condition codes, bit order is [3:0]=VNCZ
767 2 dgisselq
                        case(dcdF[2:0])
768 56 dgisselq
                        3'h0:   r_opF <= 6'h00; // Always
769 69 dgisselq
`ifdef  OPT_NEW_INSTRUCTION_SET
770
                        // These were remapped as part of the new instruction
771
                        // set in order to make certain that the low order
772
                        // two bits contained the most commonly used 
773
                        // conditions: Always, LT, Z, and NZ.
774
                        3'h1:   r_opF <= 6'h24; // LT
775
                        3'h2:   r_opF <= 6'h11; // Z
776
                        3'h3:   r_opF <= 6'h10; // NE
777
                        3'h4:   r_opF <= 6'h30; // GT (!N&!Z)
778
                        3'h5:   r_opF <= 6'h20; // GE (!N)
779
`else
780 56 dgisselq
                        3'h1:   r_opF <= 6'h11; // Z
781
                        3'h2:   r_opF <= 6'h10; // NE
782
                        3'h3:   r_opF <= 6'h20; // GE (!N)
783
                        3'h4:   r_opF <= 6'h30; // GT (!N&!Z)
784
                        3'h5:   r_opF <= 6'h24; // LT
785 69 dgisselq
`endif
786 56 dgisselq
                        3'h6:   r_opF <= 6'h02; // C
787
                        3'h7:   r_opF <= 6'h08; // V
788 2 dgisselq
                        endcase
789 36 dgisselq
                end // Bit order is { (flags_not_used), VNCZ mask, VNCZ value }
790 56 dgisselq
        assign  opF = { r_opF[3], r_opF[5], r_opF[1], r_opF[4:0] };
791 2 dgisselq
 
792 69 dgisselq
        wire    w_opvalid;
793 105 dgisselq
        assign  w_opvalid = (~clear_pipeline)&&(dcdvalid)&&(~dcd_ljmp);
794 36 dgisselq
        initial opvalid     = 1'b0;
795
        initial opvalid_alu = 1'b0;
796
        initial opvalid_mem = 1'b0;
797 91 dgisselq
        initial opvalid_div = 1'b0;
798
        initial opvalid_fpu = 1'b0;
799 2 dgisselq
        always @(posedge i_clk)
800
                if (i_rst)
801 25 dgisselq
                begin
802
                        opvalid     <= 1'b0;
803
                        opvalid_alu <= 1'b0;
804
                        opvalid_mem <= 1'b0;
805
                end else if (op_ce)
806
                begin
807 2 dgisselq
                        // Do we have a valid instruction?
808
                        //   The decoder may vote to stall one of its
809
                        //   instructions based upon something we currently
810
                        //   have in our queue.  This instruction must then
811
                        //   move forward, and get a stall cycle inserted.
812
                        //   Hence, the test on dcd_stalled here.  If we must
813
                        //   wait until our operands are valid, then we aren't
814
                        //   valid yet until then.
815 69 dgisselq
                        opvalid<= w_opvalid;
816 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
817 69 dgisselq
                        opvalid_alu <= ((dcdALU)||(dcd_illegal))&&(w_opvalid);
818
                        opvalid_mem <= (dcdM)&&(~dcd_illegal)&&(w_opvalid);
819
                        opvalid_div <= (dcdDV)&&(~dcd_illegal)&&(w_opvalid);
820
                        opvalid_fpu <= (dcdFP)&&(~dcd_illegal)&&(w_opvalid);
821 36 dgisselq
`else
822 69 dgisselq
                        opvalid_alu <= (dcdALU)&&(w_opvalid);
823
                        opvalid_mem <= (dcdM)&&(w_opvalid);
824
                        opvalid_div <= (dcdDV)&&(w_opvalid);
825
                        opvalid_fpu <= (dcdFP)&&(w_opvalid);
826 36 dgisselq
`endif
827 69 dgisselq
                end else if ((clear_pipeline)||(alu_ce)||(mem_ce)||(div_ce)||(fpu_ce))
828 25 dgisselq
                begin
829
                        opvalid     <= 1'b0;
830
                        opvalid_alu <= 1'b0;
831
                        opvalid_mem <= 1'b0;
832 69 dgisselq
                        opvalid_div <= 1'b0;
833
                        opvalid_fpu <= 1'b0;
834 25 dgisselq
                end
835 2 dgisselq
 
836
        // Here's part of our debug interface.  When we recognize a break
837
        // instruction, we set the op_break flag.  That'll prevent this
838
        // instruction from entering the ALU, and cause an interrupt before
839
        // this instruction.  Thus, returning to this code will cause the
840
        // break to repeat and continue upon return.  To get out of this
841
        // condition, replace the break instruction with what it is supposed
842
        // to be, step through it, and then replace it back.  In this fashion,
843
        // a debugger can step through code.
844 25 dgisselq
        // assign w_op_break = (dcd_break)&&(r_dcdI[15:0] == 16'h0001);
845
        initial op_break = 1'b0;
846 2 dgisselq
        always @(posedge i_clk)
847 25 dgisselq
                if (i_rst)      op_break <= 1'b0;
848
                else if (op_ce) op_break <= (dcd_break);
849
                else if ((clear_pipeline)||(~opvalid))
850
                                op_break <= 1'b0;
851 2 dgisselq
 
852 69 dgisselq
`ifdef  OPT_PIPELINED
853
        generate
854
        if (IMPLEMENT_LOCK != 0)
855
        begin
856
                reg     r_op_lock, r_op_lock_stall;
857
 
858
                initial r_op_lock_stall = 1'b0;
859
                always @(posedge i_clk)
860
                        if (i_rst)
861
                                r_op_lock_stall <= 1'b0;
862
                        else
863
                                r_op_lock_stall <= (~opvalid)||(~op_lock)
864
                                                ||(~dcdvalid)||(~pf_valid);
865
 
866
                assign  op_lock_stall = r_op_lock_stall;
867
 
868
                initial r_op_lock = 1'b0;
869
                always @(posedge i_clk)
870
                        if (i_rst)
871
                                r_op_lock <= 1'b0;
872 132 dgisselq
                        else if (op_ce)
873
                                r_op_lock <= (dcd_lock)&&(~clear_pipeline);
874 69 dgisselq
                assign  op_lock = r_op_lock;
875
 
876
        end else begin
877
                assign  op_lock_stall = 1'b0;
878
                assign  op_lock = 1'b0;
879
        end endgenerate
880
 
881
`else
882
        assign op_lock_stall = 1'b0;
883
        assign op_lock       = 1'b0;
884
`endif
885
 
886 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
887 71 dgisselq
        initial op_illegal = 1'b0;
888 2 dgisselq
        always @(posedge i_clk)
889 71 dgisselq
                if ((i_rst)||(clear_pipeline))
890
                        op_illegal <= 1'b0;
891
                else if(op_ce)
892 69 dgisselq
`ifdef  OPT_PIPELINED
893
                        op_illegal <=(dcd_illegal)||((dcd_lock)&&(IMPLEMENT_LOCK == 0));
894
`else
895
                        op_illegal <= (dcd_illegal)||(dcd_lock);
896 36 dgisselq
`endif
897 69 dgisselq
`endif
898 36 dgisselq
 
899 71 dgisselq
        // No generate on EARLY_BRANCHING here, since if EARLY_BRANCHING is not
900
        // set, dcd_early_branch will simply be a wire connected to zero and
901
        // this logic should just optimize.
902
        always @(posedge i_clk)
903
                if (op_ce)
904
                begin
905 83 dgisselq
                        opF_wr <= (dcdF_wr)&&((~dcdR_cc)||(~dcdR_wr))
906
                                &&(~dcd_early_branch)&&(~dcd_illegal);
907
                        opR_wr <= (dcdR_wr)&&(~dcd_early_branch)&&(~dcd_illegal);
908 71 dgisselq
                end
909 69 dgisselq
 
910 36 dgisselq
        always @(posedge i_clk)
911 2 dgisselq
                if (op_ce)
912
                begin
913
                        opn    <= dcdOp;        // Which ALU operation?
914 25 dgisselq
                        // opM  <= dcdM;        // Is this a memory operation?
915 2 dgisselq
                        // What register will these results be written into?
916 69 dgisselq
                        opR    <= dcdR;
917
                        opR_cc <= (dcdR_cc)&&(dcdR_wr)&&(dcdR[4]==dcd_gie);
918 2 dgisselq
                        // User level (1), vs supervisor (0)/interrupts disabled
919
                        op_gie <= dcd_gie;
920
 
921 69 dgisselq
 
922 2 dgisselq
                        //
923 48 dgisselq
                        op_pc  <= (dcd_early_branch)?dcd_branch_pc:dcd_pc;
924 2 dgisselq
                end
925
        assign  opFl = (op_gie)?(w_uflags):(w_iflags);
926
 
927 69 dgisselq
`ifdef  OPT_VLIW
928
        reg     r_op_phase;
929
        initial r_op_phase = 1'b0;
930
        always @(posedge i_clk)
931
                if ((i_rst)||(clear_pipeline))
932
                        r_op_phase <= 1'b0;
933
                else if (op_ce)
934
                        r_op_phase <= dcd_phase;
935
        assign  op_phase = r_op_phase;
936
`else
937
        assign  op_phase = 1'b0;
938
`endif
939
 
940 2 dgisselq
        // This is tricky.  First, the PC and Flags registers aren't kept in
941
        // register set but in special registers of their own.  So step one
942
        // is to select the right register.  Step to is to replace that
943
        // register with the results of an ALU or memory operation, if such
944
        // results are now available.  Otherwise, we'd need to insert a wait
945
        // state of some type.
946
        //
947
        // The alternative approach would be to define some sort of
948
        // op_stall wire, which would stall any upstream stage.
949
        // We'll create a flag here to start our coordination.  Once we
950
        // define this flag to something other than just plain zero, then
951
        // the stalls will already be in place.
952 69 dgisselq
`ifdef  OPT_PIPELINED
953 83 dgisselq
        assign  opA = ((wr_reg_ce)&&(wr_reg_id == opA_id)) // &&(opA_rd))
954 71 dgisselq
                        ?  wr_reg_vl : r_opA;
955 56 dgisselq
`else
956
        assign  opA = r_opA;
957
`endif
958 48 dgisselq
 
959 69 dgisselq
`ifdef  OPT_PIPELINED
960 83 dgisselq
        // Stall if we have decoded an instruction that will read register A
961
        //      AND ... something that may write a register is running
962
        //      AND (series of conditions here ...)
963
        //              The operation might set flags, and we wish to read the
964
        //                      CC register
965
        //              OR ... (No other conditions)
966
        assign  dcdA_stall = (dcdA_rd) // &&(dcdvalid) is checked for elsewhere
967
                                &&((opvalid)||(mem_rdbusy)
968
                                        ||(div_busy)||(fpu_busy))
969
                                &&((opF_wr)&&(dcdA_cc));
970 56 dgisselq
`else
971 69 dgisselq
        // There are no pipeline hazards, if we aren't pipelined
972
        assign  dcdA_stall = 1'b0;
973 56 dgisselq
`endif
974 36 dgisselq
 
975 69 dgisselq
`ifdef  OPT_PIPELINED
976 71 dgisselq
        assign  opB = ((wr_reg_ce)&&(wr_reg_id == opB_id)&&(opB_rd))
977
                        ? wr_reg_vl: r_opB;
978 56 dgisselq
`else
979
        assign  opB = r_opB;
980
`endif
981
 
982 69 dgisselq
`ifdef  OPT_PIPELINED
983 83 dgisselq
        // Stall if we have decoded an instruction that will read register B
984
        //      AND ... something that may write a (unknown) register is running
985
        //      AND (series of conditions here ...)
986
        //              The operation might set flags, and we wish to read the
987
        //                      CC register
988
        //              OR the operation might set register B, and we still need
989
        //                      a clock to add the offset to it
990
        assign  dcdB_stall = (dcdB_rd) // &&(dcdvalid) is checked for elsewhere
991
                                // If the op stage isn't valid, yet something
992
                                // is running, then it must have been valid.
993
                                // We'll use the last values from that stage
994
                                // (opR_wr, opF_wr, opR) in our logic below.
995
                                &&((opvalid)||(mem_rdbusy)
996 132 dgisselq
                                        ||(div_busy)||(fpu_busy)||(alu_busy))
997 83 dgisselq
                                &&(
998 38 dgisselq
                                // Stall on memory ops writing to my register
999
                                //      (i.e. loads), or on any write to my
1000
                                //      register if I have an immediate offset
1001 132 dgisselq
                                //      Actually, this is worse.  I can't tell
1002
                                //      whether or not my register is going to
1003
                                //      be written to, so 
1004 38 dgisselq
                                // Note the exception for writing to the PC:
1005
                                //      if I write to the PC, the whole next
1006
                                //      instruction is invalid, not just the
1007
                                //      operand.  That'll get wiped in the
1008
                                //      next operation anyway, so don't stall
1009 83 dgisselq
                                //      here.  This keeps a BC X, BNZ Y from
1010
                                //      stalling between the two branches.
1011
                                //      BC X, BRA Y is still clear, since BRA Y
1012
                                //      is an early branch instruction.
1013
                                //      (This exception is commented out in
1014
                                //      order to help keep our logic simple, and
1015
                                //      because multiple conditional branches
1016
                                //      following each other constitutes a
1017
                                //      fairly unusualy code structure.)
1018
                                //      
1019 132 dgisselq
                                ((~dcd_zI)&&(
1020
                                        ((opR == dcdB)&&(opR_wr))
1021
                                        ||(((opvalid_mem)||(mem_rdbusy))
1022
                                        &&(op_pipe))))
1023 83 dgisselq
                                // Stall following any instruction that will
1024
                                // set the flags, if we're going to need the
1025
                                // flags (CC) register for opB.
1026
                                ||((opF_wr)&&(dcdB_cc))
1027 38 dgisselq
                                // Stall on any ongoing memory operation that
1028 71 dgisselq
                                // will write to opB -- captured above
1029
                                // ||((mem_busy)&&(~mem_we)&&(mem_last_reg==dcdB)&&(~dcd_zI))
1030
                                );
1031 91 dgisselq
        assign  dcdF_stall = ((~dcdF[3])
1032
                                        ||((dcdA_rd)&&(dcdA_cc))
1033
                                        ||((dcdB_rd)&&(dcdB_cc)))
1034
                                        &&(opvalid)&&(opR_cc);
1035
                                // &&(dcdvalid) is checked for elsewhere
1036 56 dgisselq
`else
1037 69 dgisselq
        // No stalls without pipelining, 'cause how can you have a pipeline
1038
        // hazard without the pipeline?
1039
        assign  dcdB_stall = 1'b0;
1040 91 dgisselq
        assign  dcdF_stall = 1'b0;
1041 56 dgisselq
`endif
1042 2 dgisselq
        //
1043
        //
1044
        //      PIPELINE STAGE #4 :: Apply Instruction
1045
        //
1046
        //
1047 69 dgisselq
`ifdef  OPT_NEW_INSTRUCTION_SET
1048 56 dgisselq
        cpuops  #(IMPLEMENT_MPY) doalu(i_clk, i_rst, alu_ce,
1049 25 dgisselq
                        (opvalid_alu), opn, opA, opB,
1050 71 dgisselq
                        alu_result, alu_flags, alu_valid, alu_illegal_op,
1051
                        alu_busy);
1052 69 dgisselq
`else
1053
        cpuops_deprecated       #(IMPLEMENT_MPY) doalu(i_clk, i_rst, alu_ce,
1054
                        (opvalid_alu), opn, opA, opB,
1055
                        alu_result, alu_flags, alu_valid, alu_illegal_op);
1056 71 dgisselq
        assign  alu_busy = 1'b0;
1057 69 dgisselq
`endif
1058 2 dgisselq
 
1059 69 dgisselq
        generate
1060
        if (IMPLEMENT_DIVIDE != 0)
1061
        begin
1062 83 dgisselq
                div thedivide(i_clk, (i_rst)||(clear_pipeline), div_ce, opn[0],
1063 69 dgisselq
                        opA, opB, div_busy, div_valid, div_error, div_result,
1064
                        div_flags);
1065
        end else begin
1066
                assign  div_error = 1'b1;
1067
                assign  div_busy  = 1'b0;
1068
                assign  div_valid = 1'b0;
1069
                assign  div_result= 32'h00;
1070
                assign  div_flags = 4'h0;
1071
        end endgenerate
1072
 
1073
        generate
1074
        if (IMPLEMENT_FPU != 0)
1075
        begin
1076
                //
1077
                // sfpu thefpu(i_clk, i_rst, fpu_ce,
1078
                //      opA, opB, fpu_busy, fpu_valid, fpu_err, fpu_result,
1079
                //      fpu_flags);
1080
                //
1081
                assign  fpu_error = 1'b1;
1082
                assign  fpu_busy  = 1'b0;
1083
                assign  fpu_valid = 1'b0;
1084
                assign  fpu_result= 32'h00;
1085
                assign  fpu_flags = 4'h0;
1086
        end else begin
1087
                assign  fpu_error = 1'b1;
1088
                assign  fpu_busy  = 1'b0;
1089
                assign  fpu_valid = 1'b0;
1090
                assign  fpu_result= 32'h00;
1091
                assign  fpu_flags = 4'h0;
1092
        end endgenerate
1093
 
1094
 
1095 2 dgisselq
        assign  set_cond = ((opF[7:4]&opFl[3:0])==opF[3:0]);
1096
        initial alF_wr   = 1'b0;
1097
        initial alu_wr   = 1'b0;
1098
        always @(posedge i_clk)
1099
                if (i_rst)
1100
                begin
1101
                        alu_wr   <= 1'b0;
1102
                        alF_wr   <= 1'b0;
1103
                end else if (alu_ce)
1104
                begin
1105 65 dgisselq
                        // alu_reg <= opR;
1106 2 dgisselq
                        alu_wr  <= (opR_wr)&&(set_cond);
1107
                        alF_wr  <= (opF_wr)&&(set_cond);
1108 71 dgisselq
                end else if (~alu_busy) begin
1109 2 dgisselq
                        // These are strobe signals, so clear them if not
1110
                        // set for any particular clock
1111 65 dgisselq
                        alu_wr <= (i_halt)&&(i_dbg_we);
1112 2 dgisselq
                        alF_wr <= 1'b0;
1113
                end
1114 69 dgisselq
 
1115
`ifdef  OPT_VLIW
1116
        reg     r_alu_phase;
1117
        initial r_alu_phase = 1'b0;
1118 2 dgisselq
        always @(posedge i_clk)
1119 69 dgisselq
                if (i_rst)
1120
                        r_alu_phase <= 1'b0;
1121
                else if ((alu_ce)||(mem_ce)||(div_ce)||(fpu_ce))
1122
                        r_alu_phase <= op_phase;
1123
        assign  alu_phase = r_alu_phase;
1124
`else
1125
        assign  alu_phase = 1'b0;
1126
`endif
1127
 
1128
        always @(posedge i_clk)
1129
                if ((alu_ce)||(div_ce)||(fpu_ce))
1130 65 dgisselq
                        alu_reg <= opR;
1131
                else if ((i_halt)&&(i_dbg_we))
1132
                        alu_reg <= i_dbg_reg;
1133 69 dgisselq
 
1134 132 dgisselq
        //
1135
        // DEBUG Register write access starts here
1136
        //
1137 65 dgisselq
        reg             dbgv;
1138
        initial dbgv = 1'b0;
1139
        always @(posedge i_clk)
1140
                dbgv <= (~i_rst)&&(~alu_ce)&&((i_halt)&&(i_dbg_we));
1141 132 dgisselq
        reg     [31:0]   dbg_val;
1142 65 dgisselq
        always @(posedge i_clk)
1143 132 dgisselq
                dbg_val <= i_dbg_data;
1144
        always @(posedge i_clk)
1145 2 dgisselq
                if ((alu_ce)||(mem_ce))
1146
                        alu_gie  <= op_gie;
1147
        always @(posedge i_clk)
1148 65 dgisselq
                if ((alu_ce)||((master_ce)&&(opvalid_mem)&&(~clear_pipeline)
1149
                                &&(~mem_stalled)))
1150 2 dgisselq
                        alu_pc  <= op_pc;
1151 65 dgisselq
 
1152 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
1153 56 dgisselq
        reg     r_alu_illegal;
1154
        initial r_alu_illegal = 0;
1155 38 dgisselq
        always @(posedge i_clk)
1156 71 dgisselq
                if (clear_pipeline)
1157
                        r_alu_illegal <= 1'b0;
1158
                else if ((alu_ce)||(mem_ce))
1159 56 dgisselq
                        r_alu_illegal <= op_illegal;
1160
        assign  alu_illegal = (alu_illegal_op)||(r_alu_illegal);
1161 38 dgisselq
`endif
1162
 
1163 2 dgisselq
        initial alu_pc_valid = 1'b0;
1164 132 dgisselq
        initial mem_pc_valid = 1'b0;
1165 2 dgisselq
        always @(posedge i_clk)
1166 132 dgisselq
                if (i_rst)
1167
                        alu_pc_valid <= 1'b0;
1168
                else
1169
                        alu_pc_valid <= (alu_ce);
1170
        always @(posedge i_clk)
1171
                if (i_rst)
1172
                        mem_pc_valid <= 1'b0;
1173
                else
1174
                        mem_pc_valid <= (mem_ce);
1175 2 dgisselq
 
1176 69 dgisselq
        wire    bus_lock;
1177
`ifdef  OPT_PIPELINED
1178
        generate
1179
        if (IMPLEMENT_LOCK != 0)
1180
        begin
1181 132 dgisselq
                reg     [1:0]    r_bus_lock;
1182
                initial r_bus_lock = 2'b00;
1183 69 dgisselq
                always @(posedge i_clk)
1184
                        if (i_rst)
1185 132 dgisselq
                                r_bus_lock <= 2'b00;
1186 69 dgisselq
                        else if ((op_ce)&&(op_lock))
1187 132 dgisselq
                                r_bus_lock <= 2'b11;
1188
                        else if ((|r_bus_lock)&&((~opvalid_mem)||(~op_ce)))
1189
                                r_bus_lock <= r_bus_lock + 2'b11;
1190
                assign  bus_lock = |r_bus_lock;
1191 69 dgisselq
        end else begin
1192
                assign  bus_lock = 1'b0;
1193
        end endgenerate
1194
`else
1195
        assign  bus_lock = 1'b0;
1196
`endif
1197
 
1198 38 dgisselq
`ifdef  OPT_PIPELINED_BUS_ACCESS
1199 71 dgisselq
        pipemem #(AW,IMPLEMENT_LOCK) domem(i_clk, i_rst,(mem_ce)&&(set_cond), bus_lock,
1200 38 dgisselq
                                (opn[0]), opB, opA, opR,
1201
                                mem_busy, mem_pipe_stalled,
1202
                                mem_valid, bus_err, mem_wreg, mem_result,
1203
                        mem_cyc_gbl, mem_cyc_lcl,
1204
                                mem_stb_gbl, mem_stb_lcl,
1205
                                mem_we, mem_addr, mem_data,
1206
                                mem_ack, mem_stall, mem_err, i_wb_data);
1207
 
1208
`else // PIPELINED_BUS_ACCESS
1209 71 dgisselq
        memops  #(AW,IMPLEMENT_LOCK) domem(i_clk, i_rst,(mem_ce)&&(set_cond), bus_lock,
1210 2 dgisselq
                                (opn[0]), opB, opA, opR,
1211 38 dgisselq
                                mem_busy,
1212
                                mem_valid, bus_err, mem_wreg, mem_result,
1213 36 dgisselq
                        mem_cyc_gbl, mem_cyc_lcl,
1214
                                mem_stb_gbl, mem_stb_lcl,
1215
                                mem_we, mem_addr, mem_data,
1216
                                mem_ack, mem_stall, mem_err, i_wb_data);
1217 38 dgisselq
`endif // PIPELINED_BUS_ACCESS
1218 65 dgisselq
        assign  mem_rdbusy = ((mem_busy)&&(~mem_we));
1219 2 dgisselq
 
1220
        // Either the prefetch or the instruction gets the memory bus, but 
1221
        // never both.
1222 48 dgisselq
        wbdblpriarb     #(32,AW) pformem(i_clk, i_rst,
1223 36 dgisselq
                // Memory access to the arbiter, priority position
1224
                mem_cyc_gbl, mem_cyc_lcl, mem_stb_gbl, mem_stb_lcl,
1225
                        mem_we, mem_addr, mem_data, mem_ack, mem_stall, mem_err,
1226 2 dgisselq
                // Prefetch access to the arbiter
1227 36 dgisselq
                pf_cyc, 1'b0, pf_stb, 1'b0, pf_we, pf_addr, pf_data,
1228
                        pf_ack, pf_stall, pf_err,
1229 2 dgisselq
                // Common wires, in and out, of the arbiter
1230 36 dgisselq
                o_wb_gbl_cyc, o_wb_lcl_cyc, o_wb_gbl_stb, o_wb_lcl_stb,
1231
                        o_wb_we, o_wb_addr, o_wb_data,
1232
                        i_wb_ack, i_wb_stall, i_wb_err);
1233 2 dgisselq
 
1234 132 dgisselq
 
1235
 
1236 2 dgisselq
        //
1237
        //
1238 132 dgisselq
        //
1239
        //
1240
        //
1241
        //
1242
        //
1243
        //
1244 2 dgisselq
        //      PIPELINE STAGE #5 :: Write-back results
1245
        //
1246
        //
1247
        // This stage is not allowed to stall.  If results are ready to be
1248
        // written back, they are written back at all cost.  Sleepy CPU's
1249
        // won't prevent write back, nor debug modes, halting the CPU, nor
1250
        // anything else.  Indeed, the (master_ce) bit is only as relevant
1251
        // as knowinig something is available for writeback.
1252
 
1253
        //
1254
        // Write back to our generic register set ...
1255
        // When shall we write back?  On one of two conditions
1256
        //      Note that the flags needed to be checked before issuing the
1257
        //      bus instruction, so they don't need to be checked here.
1258
        //      Further, alu_wr includes (set_cond), so we don't need to
1259
        //      check for that here either.
1260 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
1261 132 dgisselq
        assign  wr_reg_ce = (dbgv)||(~alu_illegal)&&
1262 83 dgisselq
                        (((alu_wr)&&(~clear_pipeline)
1263
                                &&((alu_valid)||(div_valid)||(fpu_valid)))
1264
                        ||(mem_valid));
1265 36 dgisselq
`else
1266 132 dgisselq
        assign  wr_reg_ce = (dbgv)||((alu_wr)&&(~clear_pipeline))||(mem_valid)||(div_valid)||(fpu_valid);
1267 36 dgisselq
`endif
1268 2 dgisselq
        // Which register shall be written?
1269 38 dgisselq
        //      COULD SIMPLIFY THIS: by adding three bits to these registers,
1270
        //              One or PC, one for CC, and one for GIE match
1271 69 dgisselq
        //      Note that the alu_reg is the register to write on a divide or
1272
        //      FPU operation.
1273 2 dgisselq
        assign  wr_reg_id = (alu_wr)?alu_reg:mem_wreg;
1274 25 dgisselq
        // Are we writing to the CC register?
1275
        assign  wr_write_cc = (wr_reg_id[3:0] == `CPU_CC_REG);
1276 2 dgisselq
        // Are we writing to the PC?
1277
        assign  wr_write_pc = (wr_reg_id[3:0] == `CPU_PC_REG);
1278
        // What value to write?
1279 71 dgisselq
        assign  wr_reg_vl = ((mem_valid) ? mem_result
1280
                                :((div_valid|fpu_valid))
1281
                                        ? ((div_valid) ? div_result:fpu_result)
1282
                                :((dbgv) ? dbg_val : alu_result));
1283 2 dgisselq
        always @(posedge i_clk)
1284
                if (wr_reg_ce)
1285
                        regset[wr_reg_id] <= wr_reg_vl;
1286
 
1287
        //
1288
        // Write back to the condition codes/flags register ...
1289
        // When shall we write to our flags register?  alF_wr already
1290
        // includes the set condition ...
1291 69 dgisselq
        assign  wr_flags_ce = ((alF_wr)||(div_valid)||(fpu_valid))&&(~clear_pipeline)&&(~alu_illegal);
1292 83 dgisselq
        assign  w_uflags = { uhalt_phase, ufpu_err_flag,
1293 71 dgisselq
                        udiv_err_flag, ubus_err_flag, trap, ill_err_u,
1294
                        1'b0, step, 1'b1, sleep,
1295
                        ((wr_flags_ce)&&(alu_gie))?alu_flags:flags };
1296 83 dgisselq
        assign  w_iflags = { ihalt_phase, ifpu_err_flag,
1297 71 dgisselq
                        idiv_err_flag, ibus_err_flag, trap, ill_err_i,
1298
                        break_en, 1'b0, 1'b0, sleep,
1299
                        ((wr_flags_ce)&&(~alu_gie))?alu_flags:iflags };
1300 69 dgisselq
 
1301
 
1302 2 dgisselq
        // What value to write?
1303
        always @(posedge i_clk)
1304
                // If explicitly writing the register itself
1305 25 dgisselq
                if ((wr_reg_ce)&&(wr_reg_id[4])&&(wr_write_cc))
1306 2 dgisselq
                        flags <= wr_reg_vl[3:0];
1307
                // Otherwise if we're setting the flags from an ALU operation
1308
                else if ((wr_flags_ce)&&(alu_gie))
1309 69 dgisselq
                        flags <= (div_valid)?div_flags:((fpu_valid)?fpu_flags
1310
                                : alu_flags);
1311 2 dgisselq
 
1312
        always @(posedge i_clk)
1313 25 dgisselq
                if ((wr_reg_ce)&&(~wr_reg_id[4])&&(wr_write_cc))
1314 2 dgisselq
                        iflags <= wr_reg_vl[3:0];
1315
                else if ((wr_flags_ce)&&(~alu_gie))
1316 69 dgisselq
                        iflags <= (div_valid)?div_flags:((fpu_valid)?fpu_flags
1317
                                : alu_flags);
1318 2 dgisselq
 
1319
        // The 'break' enable  bit.  This bit can only be set from supervisor
1320
        // mode.  It control what the CPU does upon encountering a break
1321
        // instruction.
1322
        //
1323
        // The goal, upon encountering a break is that the CPU should stop and
1324
        // not execute the break instruction, choosing instead to enter into
1325
        // either interrupt mode or halt first.  
1326
        //      if ((break_en) AND (break_instruction)) // user mode or not
1327
        //              HALT CPU
1328
        //      else if (break_instruction) // only in user mode
1329
        //              set an interrupt flag, go to supervisor mode
1330
        //              allow supervisor to step the CPU.
1331
        //      Upon a CPU halt, any break condition will be reset.  The
1332
        //      external debugger will then need to deal with whatever
1333
        //      condition has taken place.
1334
        initial break_en = 1'b0;
1335
        always @(posedge i_clk)
1336
                if ((i_rst)||(i_halt))
1337
                        break_en <= 1'b0;
1338 25 dgisselq
                else if ((wr_reg_ce)&&(~wr_reg_id[4])&&(wr_write_cc))
1339 2 dgisselq
                        break_en <= wr_reg_vl[`CPU_BREAK_BIT];
1340 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
1341 36 dgisselq
        assign  o_break = ((break_en)||(~op_gie))&&(op_break)
1342
                                &&(~alu_valid)&&(~mem_valid)&&(~mem_busy)
1343 69 dgisselq
                                &&(~div_busy)&&(~fpu_busy)
1344 36 dgisselq
                                &&(~clear_pipeline)
1345
                        ||((~alu_gie)&&(bus_err))
1346 69 dgisselq
                        ||((~alu_gie)&&(div_valid)&&(div_error))
1347
                        ||((~alu_gie)&&(fpu_valid)&&(fpu_error))
1348 71 dgisselq
                        ||((~alu_gie)&&(alu_pc_valid)&&(alu_illegal));
1349 36 dgisselq
`else
1350
        assign  o_break = (((break_en)||(~op_gie))&&(op_break)
1351
                                &&(~alu_valid)&&(~mem_valid)&&(~mem_busy)
1352
                                &&(~clear_pipeline))
1353 118 dgisselq
                        ||((~alu_gie)&&(bus_err))
1354
                        ||((~alu_gie)&&(div_valid)&&(div_error))
1355
                        ||((~alu_gie)&&(fpu_valid)&&(fpu_error));
1356 36 dgisselq
`endif
1357 2 dgisselq
 
1358
 
1359
        // The sleep register.  Setting the sleep register causes the CPU to
1360
        // sleep until the next interrupt.  Setting the sleep register within
1361
        // interrupt mode causes the processor to halt until a reset.  This is
1362 25 dgisselq
        // a panic/fault halt.  The trick is that you cannot be allowed to
1363
        // set the sleep bit and switch to supervisor mode in the same 
1364
        // instruction: users are not allowed to halt the CPU.
1365 2 dgisselq
        always @(posedge i_clk)
1366 69 dgisselq
                if ((i_rst)||(w_switch_to_interrupt))
1367 2 dgisselq
                        sleep <= 1'b0;
1368 25 dgisselq
                else if ((wr_reg_ce)&&(wr_write_cc)&&(~alu_gie))
1369
                        // In supervisor mode, we have no protections.  The
1370
                        // supervisor can set the sleep bit however he wants.
1371 69 dgisselq
                        // Well ... not quite.  Switching to user mode and
1372
                        // sleep mode shouold only be possible if the interrupt
1373
                        // flag isn't set.
1374
                        //      Thus: if (i_interrupt)&&(wr_reg_vl[GIE])
1375
                        //              don't set the sleep bit
1376
                        //      otherwise however it would o.w. be set
1377
                        sleep <= (wr_reg_vl[`CPU_SLEEP_BIT])
1378
                                &&((~i_interrupt)||(~wr_reg_vl[`CPU_GIE_BIT]));
1379 25 dgisselq
                else if ((wr_reg_ce)&&(wr_write_cc)&&(wr_reg_vl[`CPU_GIE_BIT]))
1380
                        // In user mode, however, you can only set the sleep
1381
                        // mode while remaining in user mode.  You can't switch
1382
                        // to sleep mode *and* supervisor mode at the same
1383
                        // time, lest you halt the CPU.
1384
                        sleep <= wr_reg_vl[`CPU_SLEEP_BIT];
1385 2 dgisselq
 
1386
        always @(posedge i_clk)
1387
                if ((i_rst)||(w_switch_to_interrupt))
1388
                        step <= 1'b0;
1389 25 dgisselq
                else if ((wr_reg_ce)&&(~alu_gie)&&(wr_reg_id[4])&&(wr_write_cc))
1390 2 dgisselq
                        step <= wr_reg_vl[`CPU_STEP_BIT];
1391 132 dgisselq
                else if (((alu_pc_valid)||(mem_pc_valid))&&(step)&&(gie))
1392 2 dgisselq
                        step <= 1'b0;
1393
 
1394
        // The GIE register.  Only interrupts can disable the interrupt register
1395
        assign  w_switch_to_interrupt = (gie)&&(
1396
                        // On interrupt (obviously)
1397 69 dgisselq
                        ((i_interrupt)&&(~alu_phase)&&(~bus_lock))
1398 2 dgisselq
                        // If we are stepping the CPU
1399 132 dgisselq
                        ||(((alu_pc_valid)||(mem_pc_valid))&&(step)&&(~alu_phase)&&(~bus_lock))
1400 2 dgisselq
                        // If we encounter a break instruction, if the break
1401 36 dgisselq
                        //      enable isn't set.
1402 69 dgisselq
                        ||((master_ce)&&(~mem_rdbusy)&&(~div_busy)&&(~fpu_busy)
1403
                                &&(op_break)&&(~break_en))
1404 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
1405 36 dgisselq
                        // On an illegal instruction
1406 71 dgisselq
                        ||((alu_pc_valid)&&(alu_illegal))
1407 36 dgisselq
`endif
1408 71 dgisselq
                        // On division by zero.  If the divide isn't
1409
                        // implemented, div_valid and div_error will be short
1410
                        // circuited and that logic will be bypassed
1411
                        ||((div_valid)&&(div_error))
1412
                        // Same thing on a floating point error.
1413
                        ||((fpu_valid)&&(fpu_error))
1414
                        //      
1415 69 dgisselq
                        ||(bus_err)
1416 2 dgisselq
                        // If we write to the CC register
1417
                        ||((wr_reg_ce)&&(~wr_reg_vl[`CPU_GIE_BIT])
1418 25 dgisselq
                                &&(wr_reg_id[4])&&(wr_write_cc))
1419 2 dgisselq
                        );
1420
        assign  w_release_from_interrupt = (~gie)&&(~i_interrupt)
1421
                        // Then if we write the CC register
1422
                        &&(((wr_reg_ce)&&(wr_reg_vl[`CPU_GIE_BIT])
1423 25 dgisselq
                                &&(~wr_reg_id[4])&&(wr_write_cc))
1424 2 dgisselq
                        );
1425
        always @(posedge i_clk)
1426
                if (i_rst)
1427
                        gie <= 1'b0;
1428
                else if (w_switch_to_interrupt)
1429
                        gie <= 1'b0;
1430
                else if (w_release_from_interrupt)
1431
                        gie <= 1'b1;
1432
 
1433 25 dgisselq
        initial trap = 1'b0;
1434
        always @(posedge i_clk)
1435
                if (i_rst)
1436
                        trap <= 1'b0;
1437 132 dgisselq
                else if (w_release_from_interrupt)
1438
                        trap <= 1'b0;
1439 69 dgisselq
                else if ((alu_gie)&&(wr_reg_ce)&&(~wr_reg_vl[`CPU_GIE_BIT])
1440
                                &&(wr_write_cc)) // &&(wr_reg_id[4]) implied
1441 25 dgisselq
                        trap <= 1'b1;
1442 132 dgisselq
                else if ((wr_reg_ce)&&(wr_write_cc)&&(wr_reg_id[4]))
1443
                        trap <= wr_reg_vl[`CPU_TRAP_BIT];
1444 25 dgisselq
 
1445 38 dgisselq
`ifdef  OPT_ILLEGAL_INSTRUCTION
1446 65 dgisselq
        initial ill_err_i = 1'b0;
1447 36 dgisselq
        always @(posedge i_clk)
1448
                if (i_rst)
1449 65 dgisselq
                        ill_err_i <= 1'b0;
1450 132 dgisselq
                // Only the debug interface can clear this bit
1451 65 dgisselq
                else if ((dbgv)&&(wr_reg_id == {1'b0, `CPU_CC_REG})
1452
                                &&(~wr_reg_vl[`CPU_ILL_BIT]))
1453
                        ill_err_i <= 1'b0;
1454 71 dgisselq
                else if ((alu_pc_valid)&&(alu_illegal)&&(~alu_gie))
1455 65 dgisselq
                        ill_err_i <= 1'b1;
1456
        initial ill_err_u = 1'b0;
1457
        always @(posedge i_clk)
1458
                if (i_rst)
1459
                        ill_err_u <= 1'b0;
1460
                // The bit is automatically cleared on release from interrupt
1461 36 dgisselq
                else if (w_release_from_interrupt)
1462 65 dgisselq
                        ill_err_u <= 1'b0;
1463
                // If the supervisor writes to this register, clearing the
1464
                // bit, then clear it
1465
                else if (((~alu_gie)||(dbgv))
1466
                                &&(wr_reg_ce)&&(~wr_reg_vl[`CPU_ILL_BIT])
1467
                                &&(wr_reg_id[4])&&(wr_write_cc))
1468
                        ill_err_u <= 1'b0;
1469 71 dgisselq
                else if ((alu_pc_valid)&&(alu_illegal)&&(alu_gie))
1470 65 dgisselq
                        ill_err_u <= 1'b1;
1471 38 dgisselq
`else
1472 65 dgisselq
        assign ill_err_u = 1'b0;
1473
        assign ill_err_i = 1'b0;
1474 36 dgisselq
`endif
1475 65 dgisselq
        // Supervisor/interrupt bus error flag -- this will crash the CPU if
1476
        // ever set.
1477
        initial ibus_err_flag = 1'b0;
1478 36 dgisselq
        always @(posedge i_clk)
1479
                if (i_rst)
1480 65 dgisselq
                        ibus_err_flag <= 1'b0;
1481
                else if ((dbgv)&&(wr_reg_id == {1'b0, `CPU_CC_REG})
1482
                                &&(~wr_reg_vl[`CPU_BUSERR_BIT]))
1483
                        ibus_err_flag <= 1'b0;
1484
                else if ((bus_err)&&(~alu_gie))
1485
                        ibus_err_flag <= 1'b1;
1486
        // User bus error flag -- if ever set, it will cause an interrupt to
1487
        // supervisor mode.  
1488
        initial ubus_err_flag = 1'b0;
1489
        always @(posedge i_clk)
1490
                if (i_rst)
1491
                        ubus_err_flag <= 1'b0;
1492 36 dgisselq
                else if (w_release_from_interrupt)
1493 65 dgisselq
                        ubus_err_flag <= 1'b0;
1494
                else if (((~alu_gie)||(dbgv))&&(wr_reg_ce)
1495
                                &&(~wr_reg_vl[`CPU_BUSERR_BIT])
1496
                                &&(wr_reg_id[4])&&(wr_write_cc))
1497
                        ubus_err_flag <= 1'b0;
1498 36 dgisselq
                else if ((bus_err)&&(alu_gie))
1499 65 dgisselq
                        ubus_err_flag <= 1'b1;
1500 36 dgisselq
 
1501 69 dgisselq
        generate
1502
        if (IMPLEMENT_DIVIDE != 0)
1503
        begin
1504
                reg     r_idiv_err_flag, r_udiv_err_flag;
1505
 
1506
                // Supervisor/interrupt divide (by zero) error flag -- this will
1507
                // crash the CPU if ever set.  This bit is thus available for us
1508
                // to be able to tell if/why the CPU crashed.
1509
                initial r_idiv_err_flag = 1'b0;
1510
                always @(posedge i_clk)
1511
                        if (i_rst)
1512
                                r_idiv_err_flag <= 1'b0;
1513
                        else if ((dbgv)&&(wr_reg_id == {1'b0, `CPU_CC_REG})
1514
                                        &&(~wr_reg_vl[`CPU_DIVERR_BIT]))
1515
                                r_idiv_err_flag <= 1'b0;
1516
                        else if ((div_error)&&(div_valid)&&(~alu_gie))
1517
                                r_idiv_err_flag <= 1'b1;
1518
                // User divide (by zero) error flag -- if ever set, it will
1519
                // cause a sudden switch interrupt to supervisor mode.  
1520
                initial r_udiv_err_flag = 1'b0;
1521
                always @(posedge i_clk)
1522
                        if (i_rst)
1523
                                r_udiv_err_flag <= 1'b0;
1524
                        else if (w_release_from_interrupt)
1525
                                r_udiv_err_flag <= 1'b0;
1526
                        else if (((~alu_gie)||(dbgv))&&(wr_reg_ce)
1527
                                        &&(~wr_reg_vl[`CPU_DIVERR_BIT])
1528
                                        &&(wr_reg_id[4])&&(wr_write_cc))
1529
                                r_udiv_err_flag <= 1'b0;
1530
                        else if ((div_error)&&(alu_gie)&&(div_valid))
1531
                                r_udiv_err_flag <= 1'b1;
1532
 
1533
                assign  idiv_err_flag = r_idiv_err_flag;
1534
                assign  udiv_err_flag = r_udiv_err_flag;
1535
        end else begin
1536
                assign  idiv_err_flag = 1'b0;
1537
                assign  udiv_err_flag = 1'b0;
1538
        end endgenerate
1539
 
1540
        generate
1541
        if (IMPLEMENT_FPU !=0)
1542
        begin
1543
                // Supervisor/interrupt floating point error flag -- this will
1544
                // crash the CPU if ever set.
1545
                reg             r_ifpu_err_flag, r_ufpu_err_flag;
1546
                initial r_ifpu_err_flag = 1'b0;
1547
                always @(posedge i_clk)
1548
                        if (i_rst)
1549
                                r_ifpu_err_flag <= 1'b0;
1550
                        else if ((dbgv)&&(wr_reg_id == {1'b0, `CPU_CC_REG})
1551
                                        &&(~wr_reg_vl[`CPU_FPUERR_BIT]))
1552
                                r_ifpu_err_flag <= 1'b0;
1553
                        else if ((fpu_error)&&(fpu_valid)&&(~alu_gie))
1554
                                r_ifpu_err_flag <= 1'b1;
1555
                // User floating point error flag -- if ever set, it will cause
1556
                // a sudden switch interrupt to supervisor mode.  
1557
                initial r_ufpu_err_flag = 1'b0;
1558
                always @(posedge i_clk)
1559
                        if (i_rst)
1560
                                r_ufpu_err_flag <= 1'b0;
1561
                        else if (w_release_from_interrupt)
1562
                                r_ufpu_err_flag <= 1'b0;
1563
                        else if (((~alu_gie)||(dbgv))&&(wr_reg_ce)
1564
                                        &&(~wr_reg_vl[`CPU_FPUERR_BIT])
1565
                                        &&(wr_reg_id[4])&&(wr_write_cc))
1566
                                r_ufpu_err_flag <= 1'b0;
1567
                        else if ((fpu_error)&&(alu_gie)&&(fpu_valid))
1568
                                r_ufpu_err_flag <= 1'b1;
1569
 
1570
                assign  ifpu_err_flag = r_ifpu_err_flag;
1571
                assign  ufpu_err_flag = r_ufpu_err_flag;
1572
        end else begin
1573
                assign  ifpu_err_flag = 1'b0;
1574
                assign  ufpu_err_flag = 1'b0;
1575
        end endgenerate
1576
 
1577
`ifdef  OPT_VLIW
1578
        reg             r_ihalt_phase, r_uhalt_phase;
1579
 
1580
        initial r_ihalt_phase = 0;
1581
        initial r_uhalt_phase = 0;
1582
        always @(posedge i_clk)
1583
                if (~alu_gie)
1584
                        r_ihalt_phase <= alu_phase;
1585
        always @(posedge i_clk)
1586
                if (alu_gie)
1587
                        r_uhalt_phase <= alu_phase;
1588
                else if (w_release_from_interrupt)
1589
                        r_uhalt_phase <= 1'b0;
1590
 
1591
        assign  ihalt_phase = r_ihalt_phase;
1592
        assign  uhalt_phase = r_uhalt_phase;
1593
`else
1594
        assign  ihalt_phase = 1'b0;
1595
        assign  uhalt_phase = 1'b0;
1596
`endif
1597
 
1598 2 dgisselq
        //
1599
        // Write backs to the PC register, and general increments of it
1600
        //      We support two: upc and ipc.  If the instruction is normal,
1601
        // we increment upc, if interrupt level we increment ipc.  If
1602
        // the instruction writes the PC, we write whichever PC is appropriate.
1603
        //
1604
        // Do we need to all our partial results from the pipeline?
1605
        // What happens when the pipeline has gie and ~gie instructions within
1606
        // it?  Do we clear both?  What if a gie instruction tries to clear
1607
        // a non-gie instruction?
1608
        always @(posedge i_clk)
1609 9 dgisselq
                if ((wr_reg_ce)&&(wr_reg_id[4])&&(wr_write_pc))
1610 48 dgisselq
                        upc <= wr_reg_vl[(AW-1):0];
1611 132 dgisselq
                else if ((alu_gie)&&
1612
                                (((alu_pc_valid)&&(~clear_pipeline))
1613
                                ||(mem_pc_valid)))
1614 2 dgisselq
                        upc <= alu_pc;
1615
 
1616
        always @(posedge i_clk)
1617
                if (i_rst)
1618
                        ipc <= RESET_ADDRESS;
1619
                else if ((wr_reg_ce)&&(~wr_reg_id[4])&&(wr_write_pc))
1620 48 dgisselq
                        ipc <= wr_reg_vl[(AW-1):0];
1621 132 dgisselq
                else if ((~alu_gie)&&
1622
                                (((alu_pc_valid)&&(~clear_pipeline))
1623
                                ||(mem_pc_valid)))
1624 2 dgisselq
                        ipc <= alu_pc;
1625
 
1626
        always @(posedge i_clk)
1627
                if (i_rst)
1628
                        pf_pc <= RESET_ADDRESS;
1629
                else if (w_switch_to_interrupt)
1630
                        pf_pc <= ipc;
1631
                else if (w_release_from_interrupt)
1632
                        pf_pc <= upc;
1633
                else if ((wr_reg_ce)&&(wr_reg_id[4] == gie)&&(wr_write_pc))
1634 48 dgisselq
                        pf_pc <= wr_reg_vl[(AW-1):0];
1635 69 dgisselq
`ifdef  OPT_PIPELINED
1636 105 dgisselq
                else if ((dcd_early_branch)&&(~clear_pipeline))
1637 69 dgisselq
                        pf_pc <= dcd_branch_pc + 1;
1638
                else if ((new_pc)||((~dcd_stalled)&&(pf_valid)))
1639 56 dgisselq
                        pf_pc <= pf_pc + {{(AW-1){1'b0}},1'b1};
1640 69 dgisselq
`else
1641
                else if ((alu_pc_valid)&&(~clear_pipeline))
1642
                        pf_pc <= alu_pc;
1643
`endif
1644 2 dgisselq
 
1645
        initial new_pc = 1'b1;
1646
        always @(posedge i_clk)
1647 18 dgisselq
                if ((i_rst)||(i_clear_pf_cache))
1648 2 dgisselq
                        new_pc <= 1'b1;
1649
                else if (w_switch_to_interrupt)
1650
                        new_pc <= 1'b1;
1651
                else if (w_release_from_interrupt)
1652
                        new_pc <= 1'b1;
1653
                else if ((wr_reg_ce)&&(wr_reg_id[4] == gie)&&(wr_write_pc))
1654
                        new_pc <= 1'b1;
1655
                else
1656
                        new_pc <= 1'b0;
1657
 
1658
        //
1659
        // The debug interface
1660 56 dgisselq
        generate
1661
        if (AW<32)
1662
        begin
1663
                always @(posedge i_clk)
1664 2 dgisselq
                begin
1665
                        o_dbg_reg <= regset[i_dbg_reg];
1666
                        if (i_dbg_reg[3:0] == `CPU_PC_REG)
1667 48 dgisselq
                                o_dbg_reg <= {{(32-AW){1'b0}},(i_dbg_reg[4])?upc:ipc};
1668 2 dgisselq
                        else if (i_dbg_reg[3:0] == `CPU_CC_REG)
1669 56 dgisselq
                        begin
1670 83 dgisselq
                                o_dbg_reg[13:0] <= (i_dbg_reg[4])?w_uflags:w_iflags;
1671 56 dgisselq
                                o_dbg_reg[`CPU_GIE_BIT] <= gie;
1672
                        end
1673 2 dgisselq
                end
1674 56 dgisselq
        end else begin
1675
                always @(posedge i_clk)
1676
                begin
1677
                        o_dbg_reg <= regset[i_dbg_reg];
1678
                        if (i_dbg_reg[3:0] == `CPU_PC_REG)
1679
                                o_dbg_reg <= (i_dbg_reg[4])?upc:ipc;
1680
                        else if (i_dbg_reg[3:0] == `CPU_CC_REG)
1681
                        begin
1682 83 dgisselq
                                o_dbg_reg[13:0] <= (i_dbg_reg[4])?w_uflags:w_iflags;
1683 56 dgisselq
                                o_dbg_reg[`CPU_GIE_BIT] <= gie;
1684
                        end
1685
                end
1686
        end endgenerate
1687
 
1688 2 dgisselq
        always @(posedge i_clk)
1689 56 dgisselq
                o_dbg_cc <= { o_break, bus_err, gie, sleep };
1690 18 dgisselq
 
1691
        always @(posedge i_clk)
1692 25 dgisselq
                o_dbg_stall <= (i_halt)&&(
1693 36 dgisselq
                        (pf_cyc)||(mem_cyc_gbl)||(mem_cyc_lcl)||(mem_busy)
1694 132 dgisselq
                        ||((~opvalid)&&(~i_rst)&&(~dcd_illegal))
1695
                        ||((~dcdvalid)&&(~i_rst)&&(~pf_illegal)));
1696 2 dgisselq
 
1697
        //
1698
        //
1699
        // Produce accounting outputs: Account for any CPU stalls, so we can
1700
        // later evaluate how well we are doing.
1701
        //
1702
        //
1703 71 dgisselq
        assign  o_op_stall = (master_ce)&&(op_stall);
1704 9 dgisselq
        assign  o_pf_stall = (master_ce)&&(~pf_valid);
1705 38 dgisselq
        assign  o_i_count  = (alu_pc_valid)&&(~clear_pipeline);
1706 56 dgisselq
 
1707 65 dgisselq
`ifdef  DEBUG_SCOPE
1708 56 dgisselq
        always @(posedge i_clk)
1709 65 dgisselq
                o_debug <= {
1710 132 dgisselq
                        o_break, i_wb_err, pf_pc[1:0],
1711
                        flags,
1712 56 dgisselq
                        pf_valid, dcdvalid, opvalid, alu_valid, mem_valid,
1713
                        op_ce, alu_ce, mem_ce,
1714 65 dgisselq
                        //
1715
                        master_ce, opvalid_alu, opvalid_mem,
1716
                        //
1717
                        alu_stall, mem_busy, op_pipe, mem_pipe_stalled,
1718
                        mem_we,
1719
                        // ((opvalid_alu)&&(alu_stall))
1720
                        // ||((opvalid_mem)&&(~op_pipe)&&(mem_busy))
1721
                        // ||((opvalid_mem)&&( op_pipe)&&(mem_pipe_stalled)));
1722
                        // opA[23:20], opA[3:0],
1723 132 dgisselq
                        gie, sleep, wr_reg_ce, wr_reg_vl[4:0]
1724 71 dgisselq
                /*
1725 69 dgisselq
                        i_rst, master_ce, (new_pc),
1726
                        ((dcd_early_branch)&&(dcdvalid)),
1727
                        pf_valid, pf_illegal,
1728
                        op_ce, dcd_ce, dcdvalid, dcd_stalled,
1729
                        pf_cyc, pf_stb, pf_we, pf_ack, pf_stall, pf_err,
1730
                        pf_pc[7:0], pf_addr[7:0]
1731 71 dgisselq
                */
1732 132 dgisselq
                /*
1733
                        i_wb_err, gie, alu_illegal,
1734
                              (new_pc)||((dcd_early_branch)&&(~clear_pipeline)),
1735
                        mem_busy,
1736
                                (mem_busy)?{ (o_wb_gbl_stb|o_wb_lcl_stb), o_wb_we,
1737
                                        o_wb_addr[8:0] }
1738
                                        : { instruction[31:21] },
1739
                        pf_valid, (pf_valid) ? alu_pc[14:0]
1740
                                :{ pf_cyc, pf_stb, pf_pc[12:0] }
1741
                */
1742
                /*
1743
                        i_wb_err, gie, new_pc, dcd_early_branch,        // 4
1744
                        pf_valid, pf_cyc, pf_stb, instruction_pc[0],    // 4
1745
                        instruction[30:27],                             // 4
1746
                        dcd_gie, mem_busy, o_wb_gbl_cyc, o_wb_gbl_stb,  // 4
1747
                        dcdvalid,
1748
                        ((dcd_early_branch)&&(~clear_pipeline))         // 15
1749
                                        ? dcd_branch_pc[14:0]:pf_pc[14:0]
1750
                */
1751 56 dgisselq
                        };
1752 65 dgisselq
`endif
1753 56 dgisselq
 
1754 2 dgisselq
endmodule

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.