URL
https://opencores.org/ocsvn/de1_olpcl2294_system/de1_olpcl2294_system/trunk
Subversion Repositories de1_olpcl2294_system
Compare Revisions
- This comparison shows the changes necessary to convert path
/de1_olpcl2294_system/trunk/sw/ecos/openocd
- from Rev 2 to Rev 3
- ↔ Reverse comparison
Rev 2 → Rev 3
/lpc2294.cfg
1,59 → 1,59
|
#daemon configuration |
telnet_port 4444 |
gdb_port 3333 |
|
|
#interface |
interface ft2232 |
ft2232_device_desc "Olimex OpenOCD JTAG A" |
ft2232_layout "olimex-jtag" |
ft2232_vid_pid 0x15BA 0x0003 |
jtag_khz 1000 |
|
if { [info exists CHIPNAME] } { |
set _CHIPNAME $CHIPNAME |
} else { |
set _CHIPNAME lpc2294 |
} |
|
if { [info exists ENDIAN] } { |
set _ENDIAN $ENDIAN |
} else { |
set _ENDIAN little |
} |
|
if { [info exists CPUTAPID ] } { |
set _CPUTAPID $CPUTAPID |
} else { |
# force an error till we get a good number |
set _CPUTAPID 0xffffffff |
} |
|
|
#use combined on interfaces or targets that can't set TRST/SRST separately |
jtag_nsrst_delay 25 |
jtag_ntrst_delay 25 |
|
reset_config trst_and_srst separate |
# reset_config trst_only |
|
|
#jtag scan chain |
# jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID |
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id 0x4f1f0f0f |
|
set _TARGETNAME [format "%s.cpu" $_CHIPNAME] |
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 |
$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 |
|
#flash configuration |
#flash bank lpc2000 <base> <size> 0 0 <target#> <variant> |
flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum |
|
# flash bank cfi 0x81000000 0x100000 2 2 0 |
|
|
# For more information about the configuration files, take a look at: |
# openocd.texi |
|
|
#daemon configuration |
telnet_port 4444 |
gdb_port 3333 |
|
|
#interface |
interface ft2232 |
ft2232_device_desc "Olimex OpenOCD JTAG A" |
ft2232_layout "olimex-jtag" |
ft2232_vid_pid 0x15BA 0x0003 |
jtag_khz 1000 |
|
if { [info exists CHIPNAME] } { |
set _CHIPNAME $CHIPNAME |
} else { |
set _CHIPNAME lpc2294 |
} |
|
if { [info exists ENDIAN] } { |
set _ENDIAN $ENDIAN |
} else { |
set _ENDIAN little |
} |
|
if { [info exists CPUTAPID ] } { |
set _CPUTAPID $CPUTAPID |
} else { |
# force an error till we get a good number |
set _CPUTAPID 0xffffffff |
} |
|
|
#use combined on interfaces or targets that can't set TRST/SRST separately |
jtag_nsrst_delay 25 |
jtag_ntrst_delay 25 |
|
reset_config trst_and_srst separate |
# reset_config trst_only |
|
|
#jtag scan chain |
# jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID |
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id 0x4f1f0f0f |
|
set _TARGETNAME [format "%s.cpu" $_CHIPNAME] |
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4 |
$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0 |
|
#flash configuration |
#flash bank lpc2000 <base> <size> 0 0 <target#> <variant> |
flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum |
|
# flash bank cfi 0x81000000 0x100000 2 2 0 |
|
|
# For more information about the configuration files, take a look at: |
# openocd.texi |
|