URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
Compare Revisions
- This comparison shows the changes necessary to convert path
/openrisc/trunk/orpsocv2/boards/actel/ordb1a3pe1500/backend/par/bin
- from Rev 542 to Rev 544
- ↔ Reverse comparison
Rev 542 → Rev 544
/orsoccpuexpio.mkpinassigns
192,3 → 192,21
ETH0_SMII_TX_PIN ?=$(ORSOCEXPBOARD_ETHA_TX_PIN) |
ETH0_SMII_SYNC_PIN ?=$(ORSOCEXPBOARD_ETHA_SYNC_PIN) |
#ETH0_PHY_RSTN_PIN ?= $(ORSOCEXPBOARD_AC97_RESET_PIN) # Put this somewhere for now |
|
# |
# SD Card controller |
# |
SDC_BUS_IN_SETTINGS=-iostd LVTTL -REGISTER No -OUT_DRIVE 12 -SLEW High -RES_PULL Up -SKEW Off -OUT_LOAD 35 -fixed yes |
SDC_BUS_IO_SETTINGS=-iostd LVTTL -REGISTER No -OUT_DRIVE 12 -SLEW High -RES_PULL Up -SKEW Off -OUT_LOAD 35 -fixed yes |
SDC_BUS_OUT_SETTINGS=-iostd LVTTL -REGISTER No -OUT_DRIVE 12 -SLEW High -RES_PULL Up -SKEW Off -OUT_LOAD 35 -fixed yes |
|
# Got mapping from here: |
# http://pinouts.ru/Memory/sdcard_pinout.shtml |
# |
SDC_CARD_DETECT_PIN=$(ORSOCEXPBOARD_SDCARD_CD_PIN) |
SDC_CMD_PIN=$(ORSOCEXPBOARD_SDCARD_DI_PIN) |
SDC_CLK_PIN=$(ORSOCEXPBOARD_SDCARD_SCLK_PIN) |
SDC_DAT0_PIN=$(ORSOCEXPBOARD_SDCARD_DO_PIN) |
SDC_DAT1_PIN=$(ORSOCEXPBOARD_SDCARD_DAT1_PIN) |
SDC_DAT2_PIN=$(ORSOCEXPBOARD_SDCARD_DAT2_PIN) |
SDC_DAT3_PIN=$(ORSOCEXPBOARD_SDCARD_CS_PIN) |
/Makefile
509,14 → 509,6
echo "set_io i2c3_scl_io " $(I2C_BUS_SETTINGS) " -pinname "$(I2C_3_SCL_PIN) >> $@; \ |
echo "set_io i2c3_sda_io " $(I2C_BUS_SETTINGS) " -pinname "$(I2C_3_SDA_PIN) >> $@; \ |
fi |
$(Q)if [ ! -z $$MP2_0 ]; then \ |
echo "set_io mp2_0_i -pinname "$(MP2_0_I_PIN) >> $@; \ |
echo "set_io mp2_0_o -pinname "$(MP2_0_O_PIN) >> $@; \ |
fi |
$(Q)if [ ! -z $$MP2_1 ]; then \ |
echo "set_io mp2_1_i -pinname "$(MP2_1_I_PIN) >> $@; \ |
echo "set_io mp2_1_o -pinname "$(MP2_1_O_PIN) >> $@; \ |
fi |
$(Q)if [ ! -z $$VERSATILE_SDRAM ]; then \ |
echo "set_io sdram_a_pad_o\\[0\\] "$(SDRAM_CTRL_BUS_SETTINGS)" -pinname "$(SDRAM_A0_PIN) >> $@; \ |
echo "set_io sdram_a_pad_o\\[1\\] "$(SDRAM_CTRL_BUS_SETTINGS)" -pinname "$(SDRAM_A1_PIN) >> $@; \ |
636,6 → 628,15
echo "set_io eth0_rst_n_o "$(RST_BUS_SETTING)" -pinname "$(ETH0_PHY_RSTN_PIN) >> $@; \ |
fi; \ |
fi |
# Optimised away as it is not used: echo "set_io sdc_card_detect_pad_i " $(SDC_BUS_IN_SETTINGS) " -pinname "$(SDC_CARD_DETECT_PIN) >> $@; |
$(Q)if [ ! -z $$SDC_CONTROLLER ]; then \ |
echo "set_io sdc_cmd_pad_io " $(SDC_BUS_IO_SETTINGS) " -pinname "$(SDC_CMD_PIN) >> $@; \ |
echo "set_io sdc_dat_pad_io\\[0\\] " $(SDC_BUS_IO_SETTINGS) " -pinname "$(SDC_DAT0_PIN) >> $@; \ |
echo "set_io sdc_dat_pad_io\\[1\\] " $(SDC_BUS_IO_SETTINGS) " -pinname "$(SDC_DAT1_PIN) >> $@; \ |
echo "set_io sdc_dat_pad_io\\[2\\] " $(SDC_BUS_IO_SETTINGS) " -pinname "$(SDC_DAT2_PIN) >> $@; \ |
echo "set_io sdc_dat_pad_io\\[3\\] " $(SDC_BUS_IO_SETTINGS) " -pinname "$(SDC_DAT3_PIN) >> $@; \ |
echo "set_io sdc_clk_pad_o " $(SDC_BUS_OUT_SETTINGS) " -pinname "$(SDC_CLK_PIN) >> $@; \ |
fi |
$(Q)echo "" >> $@ |
|
|