URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
Compare Revisions
- This comparison shows the changes necessary to convert path
/openrisc/trunk/orpsocv2/boards/xilinx/ml501/sim
- from Rev 412 to Rev 415
- ↔ Reverse comparison
Rev 412 → Rev 415
/bin/Makefile
144,15 → 144,15
|
# BootROM code, which generates a verilog array select values |
BOOTROM_FILE=bootrom.v |
BOOTROM_SW_DIR=$(BOARD_SW_DIR)/bootrom |
BOOTROM_SRC=$(shell ls $(BOOTROM_SW_DIR)/* | grep -v $(BOOTROM_FILE)) |
BOOTROM_VERILOG=$(BOOTROM_SW_DIR)/$(BOOTROM_FILE) |
BOARD_BOOTROM_SW_DIR=$(BOARD_SW_DIR)/bootrom |
BOOTROM_SRC=$(shell ls $(BOARD_BOOTROM_SW_DIR)/* | grep -v $(BOOTROM_FILE)) |
BOOTROM_VERILOG=$(BOARD_BOOTROM_SW_DIR)/$(BOOTROM_FILE) |
|
bootrom: $(BOOTROM_VERILOG) |
|
$(BOOTROM_VERILOG): $(BOOTROM_SRC) |
$(Q)echo; echo "\t### Generating bootup ROM ###"; echo |
$(Q)$(MAKE) -C $(BOOTROM_SW_DIR) $(BOOTROM_FILE) |
$(Q)$(MAKE) -C $(BOARD_BOOTROM_SW_DIR) $(BOOTROM_FILE) |
|
# Suffix of file to check after each test for the string |
TEST_OUT_FILE_SUFFIX=-general.log |
161,6 → 161,7
# Dynamically generated verilog file defining configuration for various things |
# Rule actually generating this is found in definesgen.inc file. |
TEST_DEFINES_VLG=test-defines.v |
.PHONY: $(TEST_DEFINES_VLG) |
# Set V=1 when calling make to enable verbose output |
# mainly for debugging purposes. |
ifeq ($(V), 1) |
355,7 → 356,7
# DUT compile script |
modelsim_dut.scr: rtl $(RTL_VERILOG_SRC) $(RTL_VERILOG_INCLUDES) $(BOOTROM_VERILOG) |
$(Q)echo "+incdir+"$(BOARD_RTL_VERILOG_INCLUDE_DIR) > $@; |
$(Q)echo "+incdir+"$(BOOTROM_SW_DIR) >> $@; |
$(Q)echo "+incdir+"$(BOARD_BOOTROM_SW_DIR) >> $@; |
$(Q)echo "+incdir+"$(BOARD_BENCH_VERILOG_INCLUDE_DIR) >> $@; |
$(Q)echo "+libext+.v" >> $@; |
$(Q)for module in $(BOARD_RTL_VERILOG_MODULES); do if [ -d $(BOARD_RTL_VERILOG_DIR)/$$module ]; then echo "-y " $(BOARD_RTL_VERILOG_DIR)/$$module >> $@; fi; done |
473,6 → 474,9
SIM_SW_IMAGE ?=flash.in |
endif |
|
# Amount to pad the image we'll load into the SPI flash |
HEX_IMAGE_PADDING ?=0x1c0000 |
|
.PHONY : sw |
sw: $(SIM_SW_IMAGE) |
|
488,7 → 492,8
.PHONY: $(SW_TEST_DIR)/$(TEST).flashin |
$(SW_TEST_DIR)/$(TEST).flashin: |
$(Q) echo; echo "\t### Compiling software ###"; echo; |
$(Q)$(MAKE) -C $(SW_TEST_DIR) $(TEST).flashin |
$(Q)$(MAKE) -C $(SW_TEST_DIR) $(TEST).flashin \ |
HEX_IMAGE_PADDING=$(HEX_IMAGE_PADDING) |
|
.PHONY: $(SW_TEST_DIR)/$(TEST).vmem |
$(SW_TEST_DIR)/$(TEST).vmem: |
514,7 → 519,7
# No VPI support for now. $(Q) if [ -e $(VPI_SRC_C_DIR) ]; then $(MAKE) -C $(VPI_SRC_C_DIR) clean; fi |
|
clean-bootrom: |
$(MAKE) -C $(BOOTROM_SW_DIR) clean |
$(MAKE) -C $(BOARD_BOOTROM_SW_DIR) clean |
|
clean-out: |
$(Q)rm -rf $(RTL_SIM_RESULTS_DIR)/*.* |