OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

Compare Revisions

  • This comparison shows the changes necessary to convert path 
    /openrisc/trunk/rtos/rtems/make/custom
    from Rev 30 to Rev 173
    ↔ Reverse comparison
  •

Rev 30 → Rev 173

/rxgen960.cfg
0,0 → 1,74
#
# Config file for the generix RAMiX boards with i960
#
# $Id: rxgen960.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=i960
RTEMS_CPU_MODEL=i960rp
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=rxgen960
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mrp -D__i960RP__ -D__i960_RP__
 
# -pipe does not work in our local configuration of FSF GCC 2.6.0
# configured on top of Intel Release 2.4. We did this to replace
# the GCC 2.4.5 shipped with Intel Release 2.4.
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -mleaf-procedures
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
# ifeq ($(RTEMS_USE_GCC272),yes)
# ar x $(PROJECT_ROOT)/$(RTEMS_BSP_FAMILY)/lib/libbsp.a
 
# LD_LIBS += $(PROJECT_RELEASE)/lib/libbsp.a
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
@echo "rxgen960 does not support this gcc 2.7.2"
exit 1
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(OBJCOPY) -oformat binary $@ $(basename $@).bin
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
 
/default.cfg
0,0 → 1,35
# Default target settings
#
# Some of these values are redefined in the target specific .cfg files.
#
# Created by Jiri Gaisler, 16-03-97 (who is owed a debt of gratitude
# for converting RTEMS to autoconf. Thanks. --joel)
#
# $Id: default.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/target.cfg
include $(RTEMS_ROOT)/make/host.cfg
 
include $(RTEMS_ROOT)/make/main.cfg
include $(RTEMS_ROOT)/$(RTEMS_BSP)/make/bsp.cfg
 
# use the inline functions instead of the macros
# ref: src/exec/generic/Makefile
ifeq ($(RTEMS_USE_MACROS),yes)
INLINE=macros
INLINE_UPCASE=
else
INLINE=inline
INLINE_UPCASE=INLINE
endif
 
## Target compiler config file, if any
CONFIG.CC = $(RTEMS_ROOT)/make/compilers/gcc-target-default.cfg
 
## GCC specs extension file location
RTEMS_BSP_SPECS = $(PROJECT_ROOT)/$(RTEMS_BSP)/lib/bsp_specs
 
# Base name of start file
START_BASE=start
 
/gensh1.cfg
0,0 → 1,83
#
# gensh1.cfg
#
# default configuration for Hitachi sh1 processors
#
# Author: Ralf Corsepius (corsepiu@faw.uni-ulm.de)
#
# $Id: gensh1.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
HZ=20000000
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=sh
RTEMS_CPU_MODEL=sh7032
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=gensh1
 
# BSP specific preprocessor flags.
# These should only be used in BSP dependent directories.
BSP_CPPFLAGS=-DHZ=$(HZ)
 
#
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS=-m1
 
# debug flags: typically none, but we use -O1 as it produces better code
# CFLAGS_DEBUG_V = -O1
CFLAGS_DEBUG_V =
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V = -O4
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -e _start \
-T$(PROJECT_RELEASE)/lib/linkcmds\
-o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-Wl,-Map,$(basename $@).map \
$(LDLIBS) -o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
/i386ex.cfg
0,0 → 1,79
#
# Config file for the i386ex BSP
#
# $Id: i386ex.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=i386
RTEMS_CPU_MODEL=i386_nofp
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=i386ex
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS =
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# -fomit-frame-pointer breaks debugging and C++ exceptions
CFLAGS_OPTIMIZE_V=-O4
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# Something like this should produce a map file but this does not work.
 
# -Xlinker "-Map $(basename $@).map" $(LINK_OBJS)
#
# This is a good way to get debug information. The rdmp file is large
# though (1.9 Mb for hello) and greatly slows the build process.
# $(OBJDUMP) -x -m i386 -d $(basename $@).coff > $(basename $@).rdmp
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).coff \
-noinhibit-exec -Map $(basename $@).map \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).coff $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).coff > $(basename $@).num
$(SIZE) $(basename $@).coff
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).coff \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).coff $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).coff > $(basename $@).num
$(SIZE) $(basename $@).coff
endef
endif
 
# Miscellaneous additions go here
 
/gensh2.cfg
0,0 → 1,95
#
# gensh2.cfg
#
# default configuration for Hitachi sh1 processors
#
# Authors: Ralf Corsepius (corsepiu@faw.uni-ulm.de)
#
# $Id: gensh2.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
HZ:=29491200
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=sh
RTEMS_CPU_MODEL=sh7045
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=gensh2
 
# BSP specific preprocessor flags.
# These should only be used in BSP dependent directories.
BSP_CPPFLAGS=-DHZ=$(HZ)
 
#
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS= -m2
 
# debug flags: opt. is needed to fit in RAM. '-O1' has shown bad side-
# effects by failing to set up some hardware I/O registers in
# c/src/lib/libbsp/sh/gensh2/startup/hw_init.c (and perhaps elsewhere),
# which prevented proper chip initialization and muted SCI1 output.
# CFLAGS_DEBUG_V = -O4 --save-temps
CFLAGS_DEBUG_V = -O4 -g
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V = -O4
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# STANDALONE_EVB
# This switch compiles code to jump-start from FLASH, without a monitor
#
# START_HW_INIT
# This switch selects whether 'early_hw_init()' is called from
# 'start.S'; 'bsp_hw_init()' is always called from 'bspstart.c'
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "#define RTEMS_TEST_IO_STREAM 1" >>$@
@echo "/* #define STANDALONE_EVB 1 */" >>$@
@echo "#define START_HW_INIT 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -e _start \
-T$(PROJECT_RELEASE)/lib/linkcmds\
-o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -Wl,-Map,$(basename $@).map \
$(LDLIBS) -o $@ \
$(LINK_OBJS) $(LINK_LIBS) -lstdc++
$(NM) -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
/cvme961.cfg
0,0 → 1,73
#
# Config file for the Cyclone i960ca CVME961 BSP
#
# $Id: cvme961.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=i960
RTEMS_CPU_MODEL=i960ca
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=cvme961
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS=-mca
 
# -pipe does not work in our local configuration of FSF GCC 2.6.0
# configured on top of Intel Release 2.4. We did this to replace
# the GCC 2.4.5 shipped with Intel Release 2.4.
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -mleaf-procedures
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
 
define make-exe
$(LD) -u _sbrk $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
 
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
$(LDLIBS) -o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
 
/efi332.cfg
0,0 → 1,66
#
# Config file for the efi332 BSP
#
# $Id: efi332.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=mcpu32
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=efi332
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
CPU_CFLAGS = -mcpu32
 
# optimize flag: typically -0, could use -O4 or -fast, -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).nxe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).nxe \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
endif
 
 
# Miscellaneous additions go here
/eth_comm.cfg
0,0 → 1,71
#
# Config file for MPC860 based Ethernet Comm Board
#
# $Id: eth_comm.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=mpc860
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=eth_comm
 
CPU_DEFINES=-DPPC_VECTOR_FILE_BASE=0x00000000
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mcpu=860
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
# The --defsym arguments define arguments which are required by the linkcmds
# file which is designed for gcc 2.8
define make-exe
$(LD) $(XLDFLAGS) -T $(LINKCMDS) \
--defsym __fini=0 --defsym __init=0 \
-o $@ -u atexit -u __vectors -u download_entry \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).exe \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
 
 
/mvme162.cfg
0,0 → 1,103
#
# Config file for the mvme162 BSP
#
# $Id: mvme162.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
 
ifeq ($(RTEMS_MVME162_MODEL),mvme162lx)
 
RTEMS_CPU_MODEL=m68lc040
 
else
ifeq ($(RTEMS_MVME162_MODEL),)
 
RTEMS_MVME162_MODEL=mvme162
RTEMS_CPU_MODEL=m68040
 
endif # mvme162 - mc68040
endif # mvme162lx - mc68lc040
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=mvme162
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
 
ifeq ($(RTEMS_CPU_MODEL),m68040)
CPU_CFLAGS = -m68040
else
ifeq ($(RTEMS_CPU_MODEL),m68lc040)
CPU_CFLAGS = -m68040 -msoft-float
endif # mc68040
endif # mc68lc040
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "#undef $(RTEMS_MVME162_MODEL)" >>$@
@echo "#define $(RTEMS_MVME162_MODEL)" >>$@
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
 
ifeq ($(RTEMS_CPU_MODEL),m68lc040)
# override default location of Standard C Library
LIBC_LIBC=$(RTEMS_LIBC_DIR)/lib/msoft-float/libc.a
LIBC_LIBM=$(RTEMS_LIBC_DIR)/lib/msoft-float/libm.a
endif # mc68lc040
 
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).nxe \
$(START_FILE) $(LINK_OBJS) \
--start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-o $(basename $@).nxe $(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
endif
 
# Miscellaneous additions go here
 
# BSP-specific tools
SLOAD=$(PROJECT_TOOLS)/sload
/ppcn_60x.cfg
0,0 → 1,94
#
# Config file for a Radstone Technology Plc. PowerPC 60x based VME board
#
# $Id: ppcn_60x.cfg
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=ppc603e
 
# This is the actual bsp directory used during the build process.
 
RTEMS_BSP_FAMILY=ppcn_60x
 
# This contains the compiler options necessary to select the CPU model
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# PPCN_60X_USE_DINK (ppcn_60x_bsp)
# PPCN_60X_USE_NONE (ppcn_60x_bsp)
# The Score603e board can be configured with 3 ROM monitors. Only two
# are appropriate for use with RTEMS. Set exactly one of these to "1"
# to indicate which ROM monitor is on the board you are using.
#
# PPC_VECTOR_FILE_BASE (ppc)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_USE_SPRG (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use some
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers.
#
# PPC_USE_DATA_CACHE (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use
# data cache instructions to optimize the context switch code.
# This code can conflict with debuggers or emulators.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define PPCN_60X_USE_DINK 1" >>$@
@echo "#define PPCN_60X_USE_NONE 0" >>$@
@echo "#define PPC_USE_DATA_CACHE 1" >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0100" >>$@
@echo "#define PPC_USE_SPRG 0" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mcpu=603
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
CFLAGS_OPTIMIZE_V=-O0 -fno-keep-inline-functions -fvolatile-global -fvolatile
#CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions -fvolatile-global -fvolatile
 
# The following is a linkcmds file which will work without using the
# -specs system in gcc 2.8.
# $(LD) $(XLDFLAGS) -T $(LINKCMDS) \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
# $(LD) $(XLDFLAGS) -Ttext 0x20000 \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
 
# $(CC) -mmvme -mrtems -nostartfiles -mcpu=603 \
# -o $(basename $@).exe -L $(PROJECT_RELEASE)/lib \
# $(START_FILE) $(LINK_OBJS) \
# $(LD_LIBS) \
# -Wl,-\( -Wl,-lc -Wl,-lrtemsall -Wl,-lgcc -Wl,-\)
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-o $(basename $@).exe $(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
 
# Miscellaneous additions go here
 
DRIVER_ARCHITECTURE=vmebus
/mvme147.cfg
0,0 → 1,67
#
# Config file for the mvme147 BSP
#
# $Id: mvme147.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=m68030
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=mvme147
 
# default flags
CPU_CFLAGS=
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).nxe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).nxe \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
endif
# Miscellaneous additions go here
 
 
/mvme167.cfg
0,0 → 1,102
#
# Config file for the mvme167 BSP
#
# $Id: mvme167.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
# THIS BSP USES ELF IMAGES. IT WILL NOT WORK WITH COFF UNLESS CHANGES
# ARE MADE TO THE LINKCMDS FILE.
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=m68040
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=mvme167
 
#
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it. We also specify the BSP during compilation.
# This should really get its own flag, but it works here.
#
 
CPU_CFLAGS = -m68040 -DRTEMS_BSP=$(RTEMS_BSP)
CFLAGS_DEBUG_V += -ggdb
 
# optimize flag: typically -O, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# CD2401_INT_LEVEL
# Interrupt level for the CD2401.
#
# CD2401_POLLED_IO
# 0 for interrupt-driven, 1 for polled I/O.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define CD2401_INT_LEVEL 1" >>$@
@echo "#define CD2401_POLLED_IO 1" >>$@
endef
 
# Here is the rule to actually build a $(ARCH)/foo.exe
# It also builds $(ARCH)/foo.nm
# Usage ref: src/tests/sptest/sp1/Makefile
#
# We use TFTP to transfer files to the MVME167. We generate binary files
# rather than S-records. We skip the header during downloads.
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
 
# The MC68040 does not implement all MC68881/MC68882 instructions, so use
# either the gcc floating-point software support (msoft-float libraries), or
# use the Motorola FPSP floating-point emulator in
# rtems/c/src/lib/libcpu/m68k/m68040/fpsp
# The default is to use the FPSP.
# To use the msoft-float libraries, uncomment the three lines below.
# You then should comment the M68KFPSPInstallExceptionHandlers() statement
# in rtems/c/src/lib/libbsp/m68k/mvme167/startup/bststart.c in bsp_start().
# Floating-point support will then be limited. See the mvme167 README file
# for more details.
 
# LIBC_LIBC = $(RTEMS_LIBC_DIR)/lib/msoft-float/libc.a
# LIBC_LIBM = $(RTEMS_LIBC_DIR)/lib/msoft-float/libm.a
# LIBGCC = $(shell $(CC) -msoft-float -print-libgcc-file-name)
 
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).nm
$(STRIP) -o $(basename $@) $@
$(SIZE) $(basename $@).exe
endef
endif
 
# Miscellaneous additions go here
/posix.cfg
0,0 → 1,36
#
# Config file for the posix based RTEMS
#
# $Id: posix.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
# include $(RTEMS_ROOT)/make/target.cfg
include $(RTEMS_ROOT)/make/host.cfg
 
# Set them here, otherwise gcc-target-default.cfg will set them to values
# not working on some os variants (linux-RH5.0, glibc versions 2.0.0 - 2.0.7)
# These should be available on all unices
LIBC_LIBC=-lc
LIBC_LIBM=-lm
 
include $(RTEMS_ROOT)/make/custom/$(RTEMS_HOST)-posix.cfg
 
# Not applicable - let's override 'em
LINKCMDS=
START_FILE=
START_BASE=
 
# Here is the rule to actually build a $(ARCH)/foo.exe
# It also builds $(ARCH)/foo.sr and $(ARCH)/foo.nm
# Usage ref: src/tests/sptest/sp1/Makefile
#
# 'NODE' is set to 1 or 2 for multi cpu tests (ref: mptests/mp01/node1/Makefile)
# If NODE is set as an environment variable, don't trust it, zero it out.
# (NODE turns out to be a very common environment variable)
ifeq (,$(NODE))
NODE=0
else
ifeq "$(origin NODE)" "environment"
NODE=0
endif
endif
/gen68360_040.cfg
0,0 → 1,15
#
# Configuration file for a 68040 using the 68360 in companion mode
#
# $Id: gen68360_040.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
#
# All gen68360 configurations share the same base file, only the cpu model
# differs.
#
 
RTEMS_GEN68360_COMPANION_MODE=yes
 
include $(RTEMS_ROOT)/make/custom/gen68360.cfg
 
/p4000.cfg
0,0 → 1,65
#
# Config file for the algorithmics p4000 evaluation board
#
# $Id: p4000.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
# NOTE: this file is broken !
 
CPU_DEFINES+=-DP4000 -DCPU_R4000 -DP3_DIAG -D_R4000 -D__mips=3
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=p4000
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(CC) $(LDFLAGS) -nostdlib -o $(basename $@).exe \
-T$(PROJECT_RELEASE)/lib/linkcmds $(LINK_OBJS) $(LINK_LIBS) $(LD_PATHS:%=-L %)
$(OBJCOPY) -O srec $(basename $@).exe $(basename $@).srec1
$(PACKHEX) < $(basename $@).srec1 > $(basename $@).srec
$(RM) $(basename $@).srec1
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).exe \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).exe $(basename $@).srec1
$(PACKHEX) < $(basename $@).srec1 > $(basename $@).srec
$(RM) $(basename $@).srec1
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
endif
 
# Miscellaneous additions go here
 
/papyrus.cfg
0,0 → 1,85
#
# Config file for a PowerPC 403 based papyrus card
#
# $Id: papyrus.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=ppc403
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=papyrus
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
#
# PPC_VECTOR_FILE_BASE (PowerPC)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_USE_SPRG (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use some
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0100" >>$@
@echo "#define PPC_USE_SPRG 1" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mcpu=403
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions
 
# No start file
START_BASE=
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
# The --defsym arguments define arguments which are required by the linkcmds
# file which is designed for gcc 2.8
define make-exe
$(LD) $(XLDFLAGS) -T $(LINKCMDS) \
--defsym __fini=0 --defsym __init=0 \
-o $@ -u atexit -u __vectors -u download_entry \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).exe \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
 
 
/p4600.cfg
0,0 → 1,77
#
# Config file for the algorithmics p4000 evaluation board with R4600 cpu
#
# $Id: p4600.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=mips64orion
RTEMS_CPU_MODEL=R4600
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=p4000
 
CPU_CFLAGS=-mcpu=4600 -G0
CCMIPS_CFLAGS_CPU=-cpu=r4600
 
CPU_DEFINES+=-DP4000 -DCPU_R4000 -DP3_DIAG -D_R4000 -D__mips=3
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
# This rule was used in 3.6.0
# $(CC) $(LDFLAGS) -nostdlib -o $(basename $@).exe \
# -T$(PROJECT_RELEASE)/lib/linkcmds $(LINK_FILES) $(LD_PATHS:%=-L %)
 
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) \
--start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).exe $(basename $@).srec1
$(PACKHEX) < $(basename $@).srec1 > $(basename $@).srec
$(RM) $(basename $@).srec1
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-o $@ $(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $@ $(basename $@).srec1
$(PACKHEX) < $(basename $@).srec1 > $(basename $@).srec
$(RM) $(basename $@).srec1
$(NM) -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
 
/Solaris-posix.cfg
0,0 → 1,63
#
# Config file for the Solaris based RTEMS UNIX
#
# $Id: Solaris-posix.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU=unix
RTEMS_CPU_FAMILY=sparc
RTEMS_CPU_MODEL=sparc_v8
RTEMS_UNIX_FLAVOR=solaris
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=posix
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# The following define the memory reserved in the executable for the
# RTEMS Workspace and the C Program Heap.
LIBC_DEFINES += -DWORKSPACE_MB=2
LIBC_DEFINES += -DHEAPSPACE_MB=1
LIBC_DEFINES +=-DRTEMS_UNIXLIB -DRTEMS_UNIX -DMALLOC_PROVIDED -DRTEMS_DEBUG
 
DEFINES += -D__EXTENSIONS__ -Dsolaris2
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V = -O2
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# RTEMS_UNIX (unix)
# Define this to indicate this is an RTEMS UNIX port.
 
define make-target-options
echo "/* #define NDEBUG 1 */ " >>$@
echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
echo "/* #define RTEMS_DEBUG 1 */" >>$@
echo "#define RTEMS_UNIX 1 " >>$@
endef
 
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ $(LINK_OBJS) $(LINK_LIBS)
$(NM) -ng $@ > $(basename $@).num
$(SIZE) $@
endef
 
# *****************************************************************
 
 
# Miscellaneous additions go here
/idp.cfg
0,0 → 1,73
#
# Config file for the IDP BSP
#
# $Id: idp.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=m68ec040
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=idp
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -msoft-float
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
 
# override default location of Standard C Library
LIBC_LIBC=$(RTEMS_LIBC_DIR)/lib/msoft-float/libc.a
LIBC_LIBM=$(RTEMS_LIBC_DIR)/lib/msoft-float/libm.a
 
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).nxe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).nxe \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
endif
 
# Miscellaneous additions go here
/HPUX9-posix.cfg
0,0 → 1,68
#
# Config file for HPUX running the posix bsp
#
# $Id: HPUX9-posix.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
# Specify here the host and target "architectures"
RTEMS_CPU=unix
RTEMS_CPU_FAMILY=hppa1_1
RTEMS_CPU_MODEL=hppa7200
RTEMS_UNIX_FLAVOR=hpux
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=posix
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# use the macros instead of the inline functions
# The macros work better when mixed with other compilers.
INLINE=macros
INLINE_UPCASE=MACRO
 
# RTEMS_LIBC_DIR must already be set (by configuration) DOES NOT MATTER
LIBC_DEFINES=-DRTEMS_UNIXLIB -DRTEMS_UNIX -DMALLOC_PROVIDED -DRTEMS_DEBUG
 
# The following define the memory reserved in the executable for the
# RTEMS Workspace and the C Program Heap.
# NOTE: some of the timing tests need > 1M workspace
LIBC_DEFINES += -DWORKSPACE_MB=2
LIBC_DEFINES += -DHEAPSPACE_MB=1
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V = -O2
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# RTEMS_UNIX (unix)
# Define this to indicate this is an RTEMS UNIX port.
 
define make-target-options
echo "/* #define NDEBUG 1 */ " >>$@
echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
echo "/* #define RTEMS_DEBUG 1 */" >>$@
echo "#define RTEMS_UNIX 1 " >>$@
endef
 
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ $(LINK_OBJS) $(LINK_LIBS)
$(NM) -ng $@ > $(basename $@).num
$(SIZE) $@
endef
 
# Miscellaneous additions go here
 
/erc32.cfg
0,0 → 1,97
#
# Config file for the European Space Agency ERC32
# a V7 SPARC processor derived from the Cypress 601/602 set.
#
# $Id: erc32.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=sparc
RTEMS_CPU_MODEL=erc32
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=erc32
 
# The -mflat avoids the use of save/restore instructions. It has
# a negative impact on the performance of RTEMS and should not be used.
 
ifeq ($(RTEMS_USE_GCC272),yes)
# -mno-v8 says not to use v8 level instructions. i.e. use v7 only
CPU_CFLAGS = -mno-v8 -mcypress
else
# -mcpu=cypress says to optimize for a Cypress 60x chipset
CPU_CFLAGS = -mcpu=cypress
endif
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4
 
# This makes the target dependent options file
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# CONSOLE_USE_POLLED (erc32_bsp)
# CONSOLE_USE_INTERRUPTS (erc32_bsp)
# The erc32 console driver can operate in either polled or interrupt mode.
# Under the simulator (especially when FAST_UART is defined), polled seems
# to operate better. It is common for a task to print a line (like the
# end of test message) and then exit. In this case, the program returns
# control to the simulator command line before the program has even queued
# the output to the uart. Thus sis has no chance of getting the data out.
#
# SIMSPARC_FAST_IDLE (erc32_bsp)
# If defined, speed up the clock ticks while the idle task is running so
# time spent in the idle task is minimized. This significantly reduces
# the wall time required to execute the RTEMS test suites.
#
# FPU_REVB (erc32_bsp)
# If defined, enables work-around for bug 3.14 in FPU rev.B or rev.C
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define NO_TABLE_MOVE 1" >>$@
@echo "#define CONSOLE_USE_INTERRUPTS 0" >>$@
@echo "#define CONSOLE_USE_POLLED !CONSOLE_USE_INTERRUPTS" >>$@
@echo "/* #define SIMSPARC_FAST_IDLE 1 */" >>$@
@echo "#define FPU_REVB 1" >>$@
endef
 
 
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) -u _sbrk $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).exe \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
endif
# Miscellaneous additions go here
 
/dmv152.cfg
0,0 → 1,80
#
# Config file for the dmv152 BSP
#
# $Id: dmv152.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=m68020
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=dmv152
 
#
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
 
CPU_CFLAGS =
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# USE_CHANNEL_A (DMV152)
# USE_CHANNEL_B (DMV152)
# One and only one of these should be set to 1 to indicate which
# serial port is used as the RTEMS console.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define USE_CHANNEL_A 1" >>$@
@echo "#define USE_CHANNEL_B 0" >>$@
endef
 
# Here is the rule to actually build a $(ARCH)/foo.exe
# It also builds $(ARCH)/foo.sr and $(ARCH)/foo.nm
# Usage ref: src/tests/sptest/sp1/Makefile
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).nxe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).nxe \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $@
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
endif
 
# Miscellaneous additions go here
/no_bsp.cfg
0,0 → 1,31
#
# Configuration file for the "no_bsp" board
#
# $Id: no_bsp.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=no_cpu
RTEMS_CPU_MODEL=no_cpu_model
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=no_bsp
 
# Define this to yes if C++ is included in the development environment.
# This requires that at least the GNU C++ compiler and libg++ be installed.
#
# Need "main" in BSP so can't link C++ sample test or you will get
# duplicate symbol errors for main
#
HAS_CPLUSPLUS=no
 
# Miscellaneous additions go here
define make-exe
$(LD) $(LDFLAGS) -N -e _start \
-T$(PROJECT_RELEASE)/lib/linkcmds\
-o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
/mvme2307.cfg
0,0 → 1,108
#
# Config file for the PowerPC 604 based mvme2307
#
# $Id: mvme2307.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=mpc604
RTEMS_PPC_EXCEPTION_PROCESSING_MODEL=new
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=motorola_powerpc
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# CONSOLE_USE_POLLED (mvme2307_bsp)
# CONSOLE_USE_INTERRUPTS (mvme2307_bsp)
# The mvme2307 console driver has the structure to operate in either
# polled or interrupt mode. However both modes only trap to the
# monitor currently.
#
# PPC_VECTOR_FILE_BASE (PowerPC)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_USE_SPRG (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use some
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define PPCN_60X_USE_DINK 0" >>$@
@echo "#define PPCN_60X_USE_NONE 1" >>$@
@echo "#define PPC_USE_DATA_CACHE 1" >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0100" >>$@
@echo "#define PPC_USE_SPRG 1"
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mcpu=604 -mmultiple -mstring -mstrict-align
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
#CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions
CFLAGS_OPTIMIZE_V = -O4
 
# debug flags: typically none, but at least -O1 is required due to this
# BSP using inlined code
CFLAGS_DEBUG_V = -O1
 
# profile flags: typically none, but at least -O1 is required due to this
# BSP using inlined code
CFLAGS_PROFILE_V = -O1
 
# The following is a linkcmds file which will work without using the
# -specs system in gcc 2.8.
# $(LD) $(XLDFLAGS) -T $(LINKCMDS) \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
# $(LD) $(XLDFLAGS) -Ttext 0x20000 \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
 
# $(CC) -mmvme -mrtems -nostartfiles -mcpu=603 \
# -o $(basename $@).exe -L $(PROJECT_RELEASE)/lib \
# $(START_FILE) $(LINK_OBJS) \
# $(LD_LIBS) \
# -Wl,-\( -Wl,-lc -Wl,-lrtemsall -Wl,-lgcc -Wl,-\)
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ $(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
# The following commands make a bootable image but will not work outside
# the build tree.
# test -d ${PROJECT_RELEASE}/bin || mkdir ${PROJECT_RELEASE}/bin
# $(CP) $@ $(PROJECT_ROOT)/powerpc-rtems/c/mvme2307/lib/libbsp/powerpc/$(RTEMS_BSP_FAMILY)/bootloader/$(ARCH); \
# ( cd $(PROJECT_ROOT)/powerpc-rtems/c/mvme2307/lib/libbsp/powerpc/$(RTEMS_BSP_FAMILY)/bootloader; \
# $(MAKE) bootloader BINARY_LOADED=$@; )
# f=`basename $@ .exe`; \
# cp $(PROJECT_ROOT)/powerpc-rtems/c/mvme2307/lib/libbsp/powerpc/$(RTEMS_BSP_FAMILY)/bootloader/bootloader \
# ${PROJECT_RELEASE}/bin/$${f}$(LIB_VARIANT).exe \
# && chmod 755 \
# ${PROJECT_RELEASE}/bin/$${f}$(LIB_VARIANT).exe
endef
 
 
# Miscellaneous additions go here
 
# No start file
START_BASE=
/ts_386ex.cfg
0,0 → 1,88
#
# Config file for the ts-386ex BSP
#
# $Id: ts_386ex.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=i386
RTEMS_CPU_MODEL=i386_nofp
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=ts_386ex
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it. Enables software floating-point
# emulation since we don't have a i387 co-processor.
#
CPU_CFLAGS =-msoft-float -mno-fp-ret-in-387
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# -fomit-frame-pointer breaks debugging and C++ exceptions
CFLAGS_OPTIMIZE_V= -O4
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# BSP_DEBUG (BSP)
# Enables some debugging in the BSP package.
#
# LOAD_RTC_AT_START (BSP)
# Initialize RTC and load into system clock at startup. This will break
# some tests.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "#define RTEMS_DEBUG 1" >>$@
@echo "/* #define UARTDEBUG 1 */" >>$@
@echo "/* #define BSP_DEBUG 1 */" >>$@
@echo "#define LOAD_RTC_AT_START 1" >>$@
endef
 
# Something like this should produce a map file but this does not work.
 
# -Xlinker "-Map $(basename $@).map" $(LINK_OBJS)
#
# This is a good way to get debug information. The rdmp file is large
# though (1.9 Mb for hello) and greatly slows the build process.
# $(OBJDUMP) -x -m i386 -d $(basename $@).coff > $(basename $@).rdmp
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).coff \
-noinhibit-exec -Map $(basename $@).map \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).coff $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).coff > $(basename $@).num
$(SIZE) $(basename $@).coff
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).elf \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O binary $(basename $@).elf $(basename $@).exe
$(NM) -g -n $(basename $@).elf > $(basename $@).num
$(SIZE) $(basename $@).elf
endef
endif
 
# Miscellaneous additions go here
 
/helas403.cfg
0,0 → 1,91
#
# Config file for a PowerPC 403 based helas403 card
#
# $Id: helas403.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
# this is derived from:
#
# Config file for a PowerPC 403 based papyrus card
#
# Id: papyrus.cfg,v 1.7 1998/06/27 17:09:47 joel Exp
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=ppc403
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=helas403
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
#
# PPC_VECTOR_FILE_BASE (PowerPC)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_USE_SPRG (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use some
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0100" >>$@
@echo "#define PPC_USE_SPRG 1" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mcpu=403
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions
 
# No start file
START_BASE=
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
# The --defsym arguments define arguments which are required by the linkcmds
# file which is designed for gcc 2.8
define make-exe
$(LD) $(XLDFLAGS) -T $(LINKCMDS) \
--defsym __fini=0 --defsym __init=0 \
-o $@ -u atexit -u __vectors -u download_entry \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).exe \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
 
 
/mvme147s.cfg
0,0 → 1,16
#
# Config file for the mvme147s BSP
#
# $Id: mvme147s.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
#
# mvme147s and mvme147 use the same toolset
#
 
include $(RTEMS_ROOT)/make/custom/mvme147.cfg
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=mvme147s
 
# Miscellaneous additions go here
/dmv177.cfg
0,0 → 1,112
#
# Config file for a PowerPC 603e based DY-4 VMEbus Single Board Computer.
# This BSP should work with the following models:
#
# + SVME-171/DMV-171
# + SVME-176/DMV-176
#
# $Id: dmv177.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=ppc603e
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=dmv177
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# CONSOLE_USE_POLLED (psim_bsp)
# CONSOLE_USE_INTERRUPTS (psim_bsp)
# The psim console driver has the structure to operate in either
# polled or interrupt mode. However both modes only trap to the
# monitor currently.
#
# PPC_VECTOR_FILE_BASE (ppc)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_USE_SPRG (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use some
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers.
#
# PPC_USE_DATA_CACHE (RTEMS PowerPC port/BSP)
# If defined, then the PowerPC specific code in RTEMS will use
# data cache instructions to optimize the context switch code.
# This code can conflict with debuggers or emulators. It is known
# to break the Corelis PowerPC emulator with at least some combinations
# of PowerPC 603e revisions and emulator versions.
# The BSP actually contains the call that enables this.
#
# PPC_USE_INSTRUCTION_CACHE (RTEMS PowerPC port/BSP)
# If defined, then the PowerPC specific code in RTEMS will use
# data cache instructions to optimize the context switch code.
# This code can conflict with debuggers or emulators.
# The BSP actually contains the call that enables this.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define CONSOLE_USE_INTERRUPTS 0" >>$@
@echo "#define CONSOLE_USE_POLLED !CONSOLE_USE_INTERRUPTS" >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0100" >>$@
@echo "#define PPC_USE_SPRG 0" >>$@
@echo "#define PPC_USE_DATA_CACHE 0" >>$@
@echo "#define PPC_USE_INSTRUCTION_CACHE 1" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mcpu=603
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions
 
# Define this to yes if this target supports a real-time clock.
HAS_RTC=yes
 
# The following is a ld command file which works without using the
# -specs system in gcc 2.8. IT HAS NEVER BEEN TESTED WITH THIS BSP!!!
# $(LD) $(XLDFLAGS) -T $(LINKCMDS) \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
# $(LD) $(XLDFLAGS) -Ttext 0x20000 \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
 
# $(CC) -mmvme -mrtems -nostartfiles -mcpu=603 \
# -o $(basename $@).exe -L $(PROJECT_RELEASE)/lib \
# $(START_FILE) $(LINK_OBJS) \
# $(LD_LIBS) \
# -Wl,-\( -Wl,-lc -Wl,-lrtemsall -Wl,-lgcc -Wl,-\)
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-o $(basename $@).nxe $(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
$(STRIP) $(basename $@).nxe
endef
 
# Miscellaneous additions go here
 
# Let the HWAPI know which set of drivers to build
DRIVER_ARCHITECTURE=vmebus
/ods68302.cfg
0,0 → 1,106
#
# Config file for a "ODS 68302" BSP
#
# Differs from the gen68302 by providing most of the boot code as C
# code. This allows separate board definitions to be based on C
# header files. The file is based on the VARIANT defined.
#
# $Id: ods68302.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=m68302
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=ods68302
 
#
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
# 68000+softfloat results in gcc 2.95.2 giving default libraries.
# CPU_CFLAGS = -m68302 -msoft-float
CPU_CFLAGS = -m68302
CPU_DEFINES = \
-DVARIANT=$(BSP_VARIANT) -DMC68302_BASE=$(MC68302_BASE) \
-DRAM_BASE=$(RAM_BASE) -DRAM_SIZE=$(RAM_SIZE) \
-DROM_BASE=$(ROM_BASE) -DROM_SIZE=$(ROM_SIZE)
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# debugging please
CFLAGS_DEBUG_V =
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "#define RTEMS_DEBUG 1" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
 
# override default location of Standard C Library
LIBC_LIBC=$(RTEMS_LIBC_DIR)/lib/m68000/libc.a
LIBC_LIBM=$(RTEMS_LIBC_DIR)/lib/m68000/libm.a
 
define make-exe
$(LD) $(LDFLAGS) -N -Ttext $(ROM_BASE) \
-defsym MC68302_BASE=$(MC68302_BASE) \
-T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-Wl,-defsym -Wl,MC68302_BASE=$(MC68302_BASE) \
-o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
# Miscellaneous additions go here
 
ifeq "$(strip $(BSP_VARIANT))" ""
BSP_VARIANT=bare
MC68302_BASE=0x00700000
RAM_BASE=0x00000000
RAM_SIZE=0x00100000
 
ifeq ($(RTEMS_DEBUGGER),yes)
ROM_BASE=0x00010000
LINKCMDS=$(PROJECT_RELEASE)/lib/debugrom
else
ROM_BASE=0x00C00000
LINKCMDS=$(PROJECT_RELEASE)/lib/rom
endif
 
ROM_SIZE=0x00100000
 
else
 
# pattern match the variant to set the memory map
 
endif
/efi68k.cfg
0,0 → 1,70
#
# Config file for the efi68k BSP
#
# $Id: efi68k.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=m68000
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=efi68k
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
# 68000+softfloat results in gcc 2.95.2 giving default libraries.
# CPU_CFLAGS = -m68000 -msoft-float
CPU_CFLAGS = -m68000
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).nxe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).nxe \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $@
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
endif
 
# Miscellaneous additions go here
/portsw.cfg
0,0 → 1,56
#
# Custom file for "portsw" -- AMD 29205 based board
#
# $Id: portsw.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
# Note: This file is broken for sure
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=a29k
RTEMS_CPU_MODEL=a29205
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=portsw
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -e _start \
-T$(PROJECT_RELEASE)/lib/linkcmds\
-o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) -Wl,-Map,$(basename $@).map \
$(LDLIBS) -o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
/mvme136.cfg
0,0 → 1,71
#
# Config file for the mvme136 BSP
#
# $Id: mvme136.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=m68020
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=mvme136
 
#
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS =
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).nxe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).nxe \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O srec $(basename $@).nxe $(basename $@).i
$(SED) -e 's/.$$//' -e '/^S0/d' $(basename $@).i | \
$(PACKHEX) > $(basename $@).exe
$(NM) -g -n $(basename $@).nxe > $(basename $@).num
$(SIZE) $(basename $@).nxe
endef
endif
# Miscellaneous additions go here
 
 
 
/Linux-posix.cfg
0,0 → 1,65
#
# Config file for the Linux 1.x based RTEMS UNIX
#
# $Id: Linux-posix.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU=unix
RTEMS_CPU_FAMILY=i386
RTEMS_CPU_MODEL=i486dx
RTEMS_UNIX_FLAVOR=linux
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=posix
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# RTEMS_LIBC_DIR must already be set (by configuration) DOES NOT MATTER
LIBC_DEFINES =-D_POSIX_C_SOURCE
LIBC_DEFINES+=-DRTEMS_UNIXLIB -DRTEMS_UNIX -DMALLOC_PROVIDED -DRTEMS_DEBUG
 
# The following define the memory reserved in the executable for the
# RTEMS Workspace and the C Program Heap.
LIBC_DEFINES += -DWORKSPACE_MB=2
LIBC_DEFINES += -DHEAPSPACE_MB=1
 
DEFINES += -D_BSD_SOURCE
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V = -O2
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# RTEMS_UNIX (unix)
# Define this to indicate this is an RTEMS UNIX port.
 
define make-target-options
echo "/* #define NDEBUG 1 */ " >>$@
echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
echo "/* #define RTEMS_DEBUG 1 */" >>$@
echo "#define RTEMS_UNIX 1 " >>$@
endef
 
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ $(LINK_OBJS) $(LINK_LIBS)
$(NM) -ng $@ > $(basename $@).num
$(SIZE) $@
endef
 
 
# *****************************************************************
# Miscellaneous additions go here
/bender.cfg
0,0 → 1,30
#
# Configuration file for the "bender" chip
#
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=or1k
RTEMS_CPU_MODEL=or1k_model
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=bender
 
# Define this to yes if C++ is included in the development environment.
# This requires that at least the GNU C++ compiler and libg++ be installed.
#
# Need "main" in BSP so can't link C++ sample test or you will get
# duplicate symbol errors for main
#
HAS_CPLUSPLUS=no
 
# Miscellaneous additions go here
define make-exe
$(LD) $(LDFLAGS) -N -e ___rst \
-T$(PROJECT_RELEASE)/lib/linkcmds\
-o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) -lrtemsall -lcsupport -lposix -lc -lbsp /projects/or32-rtems/lib/gcc-lib/or32-rtems/2.95.2/libgcc.a -lm -lc -lcsupport --start-group --end-group
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
/Cygwin-posix.cfg
0,0 → 1,65
#
# Config file for the Cygwin based RTEMS UNIX
#
# $Id: Cygwin-posix.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU=unix
RTEMS_CPU_FAMILY=i386
RTEMS_CPU_MODEL=i486dx
RTEMS_UNIX_FLAVOR=cygwin
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=posix
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# RTEMS_LIBC_DIR must already be set (by configuration) DOES NOT MATTER
LIBC_DEFINES =-D_POSIX_C_SOURCE
LIBC_DEFINES+=-DRTEMS_UNIXLIB -DRTEMS_UNIX -DMALLOC_PROVIDED -DRTEMS_DEBUG
 
# The following define the memory reserved in the executable for the
# RTEMS Workspace and the C Program Heap.
LIBC_DEFINES += -DWORKSPACE_MB=2
LIBC_DEFINES += -DHEAPSPACE_MB=1
 
DEFINES += -D_BSD_SOURCE
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V = -O2
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# RTEMS_UNIX (unix)
# Define this to indicate this is an RTEMS UNIX port.
 
define make-target-options
echo "/* #define NDEBUG 1 */ " >>$@
echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
echo "/* #define RTEMS_DEBUG 1 */" >>$@
echo "#define RTEMS_UNIX 1 " >>$@
endef
 
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ $(LINK_OBJS) $(LINK_LIBS)
$(NM) -ng $@ > $(basename $@).num
$(SIZE) $@
endef
 
 
# *****************************************************************
# Miscellaneous additions go here
/mvme162lx.cfg
0,0 → 1,17
#
# Configuration file for a MVME162LX
#
# This is an MVME162 model with ...
#
# $Id: mvme162lx.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
#
# All mvme162 configurations share the same base file, only the cpu model
# differs.
#
 
RTEMS_MVME162_MODEL=mvme162lx
 
include $(RTEMS_ROOT)/make/custom/mvme162.cfg
 
/simhppa.cfg
0,0 → 1,131
#
# Config file for the 7100 pa-risc simulator
#
# $Id: simhppa.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=hppa1.1
RTEMS_CPU_MODEL=hppa7200
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=simhppa
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
# Possibles:
# -mpa-risc-1-1 -- HPPA 1.1 instead of 1.0
# -mportable-runtime
#
CPU_CFLAGS = -mpa-risc-1-1 -mportable-runtime
 
# Possibles:
# -Wall -- lots of warnings
# -pipe -- compiler uses pipes to talk to phases (usually faster)
# -ansi -- ANSI C compliance
# -fasm -- ANSI, but allow inline assembler
# -mgas -- we are using gas as assembler
# -fno-keep-inline-functions -- do not emit any inlines as static
CFLAGS_DEFAULT = $(CPU_CFLAGS) -Wall -ansi -fasm -mgas
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions
 
# This makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# SIMHPPA_FAST_IDLE (simhppa)
# If defined, speed up the clock ticks while the idle task is running so
# time spent in the idle task is minimized. This significantly reduces
# the wall time required to execute the RTEMS test suites.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define SIMHPPA_FAST_IDLE 1 " >>$@
endef
 
#
# GNU ld options
# `-Tbss ORG'
# `-Tdata ORG'
# `-Ttext ORG'
# Use ORG as the starting address for--respectively--the `bss',
# `data', or the `text' segment of the output file. ORG must be a
# single hexadecimal integer; for compatibility with other linkers,
# you may omit the leading `0x' usually associated with hexadecimal
# values.
 
# 'NODE' is set to 1 or 2 for multi cpu tests (ref: mptests/mp01/node1/Makefile)
# If NODE is set as an environment variable, don't trust it, zero it out.
# (NODE turns out to be a very common environment variable)
ifeq (,$(NODE))
NODE=0
else
ifeq "$(origin NODE)" "environment"
NODE=0
endif
endif
 
# XXX some/all of this should move into 'linkcmds'
# single processor
DATA_0_BASE=0x40001000
TEXT_0_BASE=0x00001000
 
# first node (mptests number them from 1)
DATA_1_BASE=$(DATA_0_BASE)
TEXT_1_BASE=$(TEXT_0_BASE)
 
# second node (mptests number them from 1)
DATA_2_BASE=0x48001000
TEXT_2_BASE=0x08001000
 
# for hpux ld
#LD_LOC_OPTIONS=-D $(DATA_$(NODE)_BASE) -R $(TEXT_$(NODE)_BASE)
# for gnu ld
LD_LOC_OPTIONS=-Tdata $(DATA_$(NODE)_BASE) -Ttext $(TEXT_$(NODE)_BASE)
GCC_LD_LOC_OPTIONS=-W,l-T -W,ldata -W,l$(DATA_$(NODE)_BASE) \
-W,l-T -W,ltext -W,l$(TEXT_$(NODE)_BASE)
 
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LDARGS) $(LD) $(LD_LOC_OPTIONS) $(XLDFLAGS) -a archive \
-o $@ -u atexit \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) $(GCC_LD_LOC_OPTIONS) \
-o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
 
# BSP-specific tools
PRINTDUMP=$(PROJECT_TOOLS)/print_dump
/pc386.cfg
0,0 → 1,146
#
# Config file for the PC 386 BSP
#
# $Id: pc386.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=i386
ifeq ($(RTEMS_CPU_MODEL),)
RTEMS_CPU_MODEL=i386_fp
endif
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=pc386
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
# NOTE: CPU_CFLAGS is set by pc386 variants.
# CPU_CFLAGS =
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# -fomit-frame-pointer breaks debugging and C++ exceptions
CFLAGS_OPTIMIZE_V=-O4
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "/* #define RTEMS_TEST_NO_PAUSE 1 */" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# Here is the rule to actually build a $(ARCH)/foo.exe
# It also builds $(ARCH)/foo.sr and $(ARCH)/foo.nm
# Usage ref: src/tests/sptest/sp1/Makefile
 
#+--------------------------------------------------------------------------+
#| Set the value of RELOCADDR to the address where you want your image to
#| load. If you'll be using GRUB to load the images it will have to be >=
#| 0x100000 (1024K). If you are using NetBoot to load the images it can be
#| >= 0x10000 (64K) AND <= 0x97C00 (607K) OR >= 0x100000 (1024K). The memory
#| top is of course another limit. Make sure there is enough space before the
#| upper memory limits for the image and the memory allocated by it to fit.
#| Make sure the value you choose is aligned to 4 bytes.
#+--------------------------------------------------------------------------+
RELOCADDR=0x00100000
 
START16FILE=$(PROJECT_RELEASE)/lib/start16$(LIB_VARIANT).bin
START16ADDR=0x00097C00
HEADERADDR=0x00097E00
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(LD) -N -T $(LINKCMDS) -Ttext $(RELOCADDR) -e start -nostdlib \
-o $(basename $@).obj \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(OBJCOPY) -O a.out-i386 \
--remove-section=.rodata \
--remove-section=.comment \
--remove-section=.note \
--strip-unneeded $(basename $@).obj $@
$(OBJCOPY) -O binary $(basename $@).obj $(basename $@).bin
$(BIN2BOOT) -v $(basename $@).bt $(HEADERADDR)\
$(START16FILE) $(START16ADDR) 0 $(basename $@).bin $(RELOCADDR) 0
$(NM) -g -n $(basename $@).obj > $(basename $@).num
$(SIZE) $(basename $@).obj
test -d ${PROJECT_RELEASE}/BootImgs \
|| mkdir ${PROJECT_RELEASE}/BootImgs
cp $(basename $@).bt \
${PROJECT_RELEASE}/BootImgs/$(basename $@)$(LIB_VARIANT).bt
chmod 755 \
${PROJECT_RELEASE}/BootImgs/$(basename $@)$(LIB_VARIANT).bt
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -Wl,-Ttext,$(RELOCADDR) \
-o $(basename $@).obj \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O elf32-i386 \
--remove-section=.rodata \
--remove-section=.comment \
--remove-section=.note \
--strip-unneeded $(basename $@).obj $@
$(OBJCOPY) -O binary $(basename $@).obj $(basename $@).bin
$(PROJECT_TOOLS)/bin2boot -v $(basename $@).bt $(HEADERADDR)\
$(START16FILE) $(START16ADDR) 0 $(basename $@).bin $(RELOCADDR) 0
$(NM) -g -n $(basename $@).obj > $(basename $@).num
$(SIZE) $(basename $@).obj
test -d ${PROJECT_RELEASE}/BootImgs \
|| mkdir ${PROJECT_RELEASE}/BootImgs
f=`basename $@ .exe`; \
cp $(basename $@).bt \
${PROJECT_RELEASE}/BootImgs/$${f}$(LIB_VARIANT).bt \
&& chmod 755 \
${PROJECT_RELEASE}/BootImgs/$${f}$(LIB_VARIANT).bt
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -Wl,-Ttext,$(RELOCADDR) \
-o $@ $(LINK_OBJS) $(LINK_LIBS)
endef
define make-cxx-exe
$(LINK.cc) $(AM_CFLAGS) $(AM_CXXFLAGS) $(AM_LDFLAGS) \
-Wl,-Ttext,$(RELOCADDR) -o $(basename $@).obj \
$(LINK_OBJS) $(LINK_LIBS)
$(OBJCOPY) -O elf32-i386 \
--remove-section=.rodata \
--remove-section=.comment \
--remove-section=.note \
--strip-unneeded $(basename $@).obj $@
$(OBJCOPY) -O binary $(basename $@).obj $(basename $@).bin
$(PROJECT_TOOLS)/bin2boot -v $(basename $@).bt $(HEADERADDR)\
$(START16FILE) $(START16ADDR) 0 $(basename $@).bin $(RELOCADDR) 0
$(NM) -g -n $(basename $@).obj > $(basename $@).num
$(SIZE) $(basename $@).obj
test -d ${PROJECT_RELEASE}/BootImgs \
|| mkdir ${PROJECT_RELEASE}/BootImgs
f=`basename $@ .exe`; \
cp $(basename $@).bt \
${PROJECT_RELEASE}/BootImgs/$${f}$(LIB_VARIANT).bt \
&& chmod 755 \
${PROJECT_RELEASE}/BootImgs/$${f}$(LIB_VARIANT).bt
$(LINK.cc) $(AM_CFLAGS) $(AM_CXXFLAGS) $(AM_LDFLAGS) \
-Wl,-Ttext,$(RELOCADDR) \
-o $(basename $@).coff $(LINK_OBJS) $(LINK_LIBS)
endef
endif
 
# Miscellaneous additions go here
 
# BSP-specific tools
BIN2BOOT=$(PROJECT_TOOLS)/bin2boot
/pc486.cfg
0,0 → 1,11
#
# Configuration file for a PC using an i486DX Class CPU
#
# $Id: pc486.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU_MODEL=i486dx
CPU_CFLAGS = -mcpu=i486
 
include $(RTEMS_ROOT)/make/custom/pc386.cfg
 
/pc586.cfg
0,0 → 1,11
#
# Configuration file for a PC using a Pentium Class CPU
#
# $Id: pc586.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU_MODEL=pentium
CPU_CFLAGS = -mcpu=i586
 
include $(RTEMS_ROOT)/make/custom/pc386.cfg
 
/pc686.cfg
0,0 → 1,11
#
# Configuration file for a PC using a PentiumPro Class CPU
#
# $Id: pc686.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU_MODEL=pentiumpro
CPU_CFLAGS = -mcpu=i686
 
include $(RTEMS_ROOT)/make/custom/pc386.cfg
 
/psim.cfg
0,0 → 1,100
#
# Config file for the PowerPC 60x simulator - psim
#
# $Id: psim.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=ppc603e
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=psim
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# CONSOLE_USE_POLLED (psim_bsp)
# CONSOLE_USE_INTERRUPTS (psim_bsp)
# The psim console driver has the structure to operate in either
# polled or interrupt mode. However both modes only trap to the
# monitor currently.
#
# PSIM_FAST_IDLE (psim_bsp)
# If defined, speed up the clock ticks while the idle task is running so
# time spent in the idle task is minimized. This significantly reduces
# the wall time required to execute the RTEMS test suites.
#
# PPC_VECTOR_FILE_BASE (PowerPC)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_USE_SPRG (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use some
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers.
 
 
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define CONSOLE_USE_INTERRUPTS 0" >>$@
@echo "#define CONSOLE_USE_POLLED !CONSOLE_USE_INTERRUPTS" >>$@
@echo "#define PSIM_FAST_IDLE 1" >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0xFFF00100" >>$@
@echo "#define PPC_USE_SPRG 1" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mcpu=603
#-ffunction-sections
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions
 
# The following is a linkcmds file which will work without using the
# -specs system in gcc 2.8.
# $(LD) $(XLDFLAGS) -T $(LINKCMDS) \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
# $(LD) $(XLDFLAGS) -Ttext 0x20000 \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
 
# $(CC) -mmvme -mrtems -nostartfiles -mcpu=603 \
# -o $(basename $@).exe -L $(PROJECT_RELEASE)/lib \
# $(START_FILE) $(LINK_OBJS) \
# $(LD_LIBS) \
# -Wl,-\( -Wl,-lc -Wl,-lrtemsall -Wl,-lgcc -Wl,-\)
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
$(CC) $(CFLAGS) -o $(basename $@).exe $(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
else
# -Wl,--gc-sections
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).exe \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
# Miscellaneous additions go here
/bare.cfg
0,0 → 1,53
#
# Config file for the "bare" BSP
#
# $Id: bare.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=bare
 
RTEMS_BSP=bare
 
RTEMS_CPU_MODEL=$(BARE_CPU_MODEL)
 
CPU_CFLAGS=$(BARE_CPU_CFLAGS)
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# this target has no start file
START_BASE=
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
define make-exe
echo "Cannot do a link with the bare bsp."
echo "#!/bin/sh" > $(basename $@).exe
echo "echo \"Cannot do a link with the bare bsp.\"" >> $(basename $@).exe
endef
 
# Miscellaneous additions go here
/score603e.cfg
0,0 → 1,131
#
# Config file for a PowerPC 603e based Vista VMEbus Single Board Computer.
# This BSP should work with the following models:
#
# + Vista SCORE 603e
#
# $Id: score603e.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=ppc603e
 
# Set the default generation if it has not been overridden
ifeq ($(SCORE603E_GENERATION),)
SCORE603E_GENERATION=2
endif
 
 
# This is the actual bsp directory used during the build process.
 
RTEMS_BSP_FAMILY=score603e
 
ifeq ($(SCORE603E_GENERATION),1)
RTEMS_BSP=score603e_g1
 
else
ifeq ($(SCORE603E_GENERATION),2)
RTEMS_BSP=score603e
 
endif # generation 2
endif # generation 1
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# CONSOLE_USE_POLLED (score603e_bsp)
# CONSOLE_USE_INTERRUPTS (score603e_bsp)
# The score603e console driver has the structure to operate in either
# polled or interrupt mode. However both modes only trap to the
# monitor currently.
#
# SCORE603E_USE_SDS (score603e_bsp)
# SCORE603E_USE_OPEN_FIRMWARE (score603e_bsp)
# SCORE603E_USE_NONE (score603e_bsp)
# The Score603e board can be configured with 3 ROM monitors. Only two
# are appropriate for use with RTEMS. Set exactly one of these to "1"
# to indicate which ROM monitor is on the board you are using.
#
# PPC_VECTOR_FILE_BASE (ppc)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_USE_SPRG (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use some
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers.
#
# PPC_USE_DATA_CACHE (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use
# data cache instructions to optimize the context switch code.
# This code can conflict with debuggers or emulators.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define CONSOLE_USE_INTERRUPTS 0" >>$@
@echo "#define INITIALIZE_COM_PORTS 1" >>$@
@echo "#define SCORE603E_GENERATION $(SCORE603E_GENERATION)" >>$@
@echo "#define SCORE603E_USE_SDS 0" >>$@
@echo "#define SCORE603E_USE_NONE 0" >>$@
@echo "#define SCORE603E_USE_DINK 1" >>$@
@echo "#define SCORE603E_USE_OPEN_FIRMWARE 0" >>$@
@echo "#define PPC_USE_DATA_CACHE 0" >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0100" >>$@
@echo "#define PPC_USE_SPRG 0" >>$@
@echo "#define HAS_PMC_PSC8 0" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
CPU_CFLAGS = -mcpu=603
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE: some level of -O may be actually required by inline assembler
CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions
# CFLAGS_OPTIMIZE_V=-O0
 
# The following is a linkcmds file which will work without using the
# -specs system in gcc 2.8.
# $(LD) $(XLDFLAGS) -T $(LINKCMDS) \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
# $(LD) $(XLDFLAGS) -Ttext 0x20000 \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
 
ifeq ($(RTEMS_USE_GCC272),yes)
define make-exe
@echo gcc 2.7.2 style linking not supported by score603e
@exit 1
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-o $(basename $@).elf $(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $(basename $@).elf > $(basename $@).num
$(SIZE) $(basename $@).elf
$(OBJCOPY) -O srec $(basename $@).elf $(basename $@).s1
sed -e 's/.$$//' $(basename $@).s1 | \
$(PACKHEX) >$(basename $@).exe
rm -f $(basename $@).s1
endef
endif
 
# Miscellaneous additions go here
 
DRIVER_ARCHITECTURE=vmebus
/FreeBSD-posix.cfg
0,0 → 1,63
#
# Config file for the FreeBSD 2.x based RTEMS UNIX
#
#
 
RTEMS_CPU=unix
RTEMS_CPU_FAMILY=i386
RTEMS_CPU_MODEL=i486dx
RTEMS_UNIX_FLAVOR=freebsd
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=posix
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# RTEMS_LIBC_DIR must already be set (by configuration) DOES NOT MATTER
LIBC_DEFINES =-D_POSIX_C_SOURCE
LIBC_DEFINES+=-DRTEMS_UNIXLIB -DRTEMS_UNIX -DMALLOC_PROVIDED -DRTEMS_DEBUG
 
# The following define the memory reserved in the executable for the
# RTEMS Workspace and the C Program Heap.
LIBC_DEFINES += -DWORKSPACE_MB=2
LIBC_DEFINES += -DHEAPSPACE_MB=1
 
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V = -O2
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# NO_TABLE_MOVE (SPARC PORT)
# do not have a second trap table -- use the BSP's
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# RTEMS_UNIX (unix)
# Define this to indicate this is an RTEMS UNIX port.
 
define make-target-options
echo "/* #define NDEBUG 1 */ " >>$@
echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
echo "/* #define RTEMS_DEBUG 1 */" >>$@
echo "#define RTEMS_UNIX 1 " >>$@
endef
 
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ $(LINK_OBJS) $(LINK_LIBS)
$(NM) -ng $@ > $(basename $@).num
$(SIZE) $@
endef
 
 
# *****************************************************************
# Miscellaneous additions go here
/mcp750.cfg
0,0 → 1,110
#
# Config file for Motorola MCP750 -- a MPC750 CompactPCI board
#
# $Id: mcp750.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=powerpc
RTEMS_CPU_MODEL=mpc750
RTEMS_PPC_EXCEPTION_PROCESSING_MODEL=new
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=motorola_powerpc
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
# PPC_VECTOR_FILE_BASE (ppc)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_USE_SPRG (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use some
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers.
#
# PPC_USE_DATA_CACHE (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use
# data cache instructions to optimize the context switch code.
# This code can conflict with debuggers or emulators.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define PPCN_60X_USE_DINK 0" >>$@
@echo "#define PPCN_60X_USE_NONE 1" >>$@
@echo "#define PPC_USE_DATA_CACHE 1" >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0100" >>$@
@echo "#define PPC_USE_SPRG 1" >>$@
endef
 
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
# NOTE : cheking egcc 1.1.1 source code shows that the last know processor
# is the 604 model and that this is the default generation option.
#
CPU_CFLAGS = -mcpu=750
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
# NOTE2: some level of -O may be actually required by inline assembler (at least
# -O2 so far.
# NOTE2 Apparently nobody really knows the status or r2 and r13.
# As far as I know, small data are pointer impose a very specific compliation
# model => not used.
# Currently the sdata2 and sbss2 sections are empty => r2 is not used...
CFLAGS_OPTIMIZE_V=-O4 -mmultiple -mstring -mstrict-align
#CFLAGS_OPTIMIZE_V=-O4 -fno-keep-inline-functions -fvolatile-global -fvolatile -mstrict-align -mcpu=750
 
# debug flags: typically none, but at least -O1 is required due to this
# BSP using inlined code
CFLAGS_DEBUG_V = -O1 -mmultiple -mstring -mstrict-align
 
 
# The following is a ld command file which works without using the
# -specs system in gcc 2.8. IT HAS NEVER BEEN TESTED WITH THIS BSP!!!
# $(LD) $(XLDFLAGS) -T $(LINKCMDS) \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
# $(LD) $(XLDFLAGS) -Ttext 0x20000 \
# -o $@ -u atexit -u __vectors -u download_entry $(LINK_FILES)
 
# $(CC) -mmvme -mrtems -nostartfiles -mcpu=603 \
# -o $(basename $@).exe -L $(PROJECT_RELEASE)/lib \
# $(START_FILE) $(LINK_OBJS) \
# $(LD_LIBS) \
# -Wl,-\( -Wl,-lc -Wl,-lrtemsall -Wl,-lgcc -Wl,-\)
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-o $@ $(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
test -d ${PROJECT_RELEASE}/bin || mkdir ${PROJECT_RELEASE}/bin
$(CP) $@ $(PROJECT_ROOT)/powerpc-rtems/c/mcp750/lib/libbsp/powerpc/$(RTEMS_BSP_FAMILY)/bootloader/$(ARCH); \
( cd $(PROJECT_ROOT)/powerpc-rtems/c/mcp750/lib/libbsp/powerpc/$(RTEMS_BSP_FAMILY)/bootloader; \
$(MAKE) bootloader BINARY_LOADED=$@; )
f=`basename $@ .exe`; \
cp $(PROJECT_ROOT)/powerpc-rtems/c/mcp750/lib/libbsp/powerpc/$(RTEMS_BSP_FAMILY)/bootloader/bootloader \
${PROJECT_RELEASE}/bin/$${f}$(LIB_VARIANT).exe \
&& chmod 755 \
${PROJECT_RELEASE}/bin/$${f}$(LIB_VARIANT).exe
endef
 
# Miscellaneous additions go here
 
# Let the HWAPI know which set of drivers to build
DRIVER_ARCHITECTURE=compactpci
/Makefile.am
0,0 → 1,23
##
## $Id: Makefile.am,v 1.2 2001-09-27 12:02:52 chris Exp $
##
 
AUTOMAKE_OPTIONS = foreign 1.4
 
rtems_makedir = $(prefix)/make
rtems_make_customdir = $(rtems_makedir)/custom
 
rtems_make_custom_DATA = default.cfg
 
EXTRA_DIST = Cygwin-posix.cfg FreeBSD-posix.cfg HPUX9-posix.cfg \
Linux-posix.cfg Solaris-posix.cfg bare.cfg cvme961.cfg dmv152.cfg \
dmv177.cfg efi332.cfg efi68k.cfg erc32.cfg eth_comm.cfg gen68302.cfg \
gen68340.cfg gen68360.cfg gen68360_040.cfg gensh1.cfg helas403.cfg \
i386ex.cfg idp.cfg mcp750.cfg mvme136.cfg mvme147.cfg mvme147s.cfg \
mvme162.cfg mvme162lx.cfg mvme167.cfg mvme2307.cfg no_bsp.cfg \
ods68302.cfg p4000.cfg p4600.cfg p4650.cfg papyrus.cfg pc386.cfg \
portsw.cfg posix.cfg ppcn_60x.cfg psim.cfg score603e.cfg simhppa.cfg \
ts_386ex.cfg
 
## -------------------------------------------------------
include $(top_srcdir)/automake/host.am
/gen68302.cfg
0,0 → 1,69
#
# Config file for a "generic 68302" BSP
#
# $Id: gen68302.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=m68k
RTEMS_CPU_MODEL=m68302
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=gen68302
 
#
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#
# 68000+softfloat results in gcc 2.95.2 giving default libraries.
# CPU_CFLAGS = -m68302 -msoft-float
CPU_CFLAGS = -m68302
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
 
# override default location of Standard C Library
LIBC_LIBC=$(RTEMS_LIBC_DIR)/lib/m68000/libc.a
LIBC_LIBM=$(RTEMS_LIBC_DIR)/lib/m68000/libm.a
 
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
# Miscellaneous additions go here
/gen68340.cfg
0,0 → 1,84
#
# Config file for a "generic 68340" BSP
#
# $Id: gen68340.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU=m68k
 
RTEMS_CPU_MODEL=mcpu32
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=gen68340
 
CPU_CFLAGS = -mcpu32
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
 
# override default location of Standard C Library
LIBC_LIBC=$(RTEMS_LIBC_DIR)/lib/m68000/msoft-float/libc.a
LIBC_LIBM=$(RTEMS_LIBC_DIR)/lib/m68000/msoft-float/libm.a
 
define make-exe
@ echo
@ echo "WARNING: newlib may use bit test instructions!!"
@ echo
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
 
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) \
-o $@ $(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
# if you want to make a prom image
# m68k-rtems-objcopy --adjust-section-vma \
# .data=`m68k-rtems-objdump --section-headers $(basename $@).exe | \
# awk 'function h2d(x) { x=toupper(x); digits=length(x); s=0 ; \
# for (p=digits; p>0; p--) \
# s += (16^(p-1)) * ( index("0123456789ABCDEF",\
# substr(x,1+digits-p,1)) -1 );\
# return s } ;\
# /\.text/ { base = $$4 ; size = $$3 };\
# END { printf("0x%x", h2d(base) + h2d(size)) }'\
# ` $(basename $@).exe
# if you want to convert it to ieee
# m68k-rtems-objcopy --output-target=ieee --debugging \
# $(basename $@).exe $(basename $@).ieee
endif
 
 
# Miscellaneous additions go here
/p4650.cfg
0,0 → 1,75
#
# Config file for the algorithmics p4000 evaluation board with R4650 cpu
#
# $Id: p4650.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
RTEMS_CPU=mips64orion
RTEMS_CPU_MODEL=R4650
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=p4000
 
CPU_CFLAGS=-m4650 -G0
CCMIPS_CFLAGS_CPU=-cpu=r4650
 
CPU_DEFINES+=-DP4000 -DCPU_R4000 -DP3_DIAG -D_R4000 -D__mips=3
 
# This section makes the target dependent options file.
 
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
 
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
 
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
# This rule was used in 3.6.0
# $(CC) $(LDFLAGS) -nostdlib -o $(basename $@).exe \
# -T$(PROJECT_RELEASE)/lib/linkcmds $(LINK_FILES) $(LD_PATHS:%=-L %)
 
define make-exe
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) \
--start-group $(LINK_LIBS) --end-group $(LD_LIBS)
$(OBJCOPY) -O srec $(basename $@).exe $(basename $@).srec1
$(PACKHEX) < $(basename $@).srec1 > $(basename $@).srec
$(RM) $(basename $@).srec1
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $(basename $@).exe \
$(LINK_OBJS) $(LINK_LIBS) $(LD_LIBS)
$(OBJCOPY) -O srec $(basename $@).exe $(basename $@).srec1
$(PACKHEX) < $(basename $@).srec1 > $(basename $@).srec
$(RM) $(basename $@).srec1
$(NM) -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
endif
 
# Miscellaneous additions go here
/gen68360.cfg
0,0 → 1,90
#
# Config file for a "generic 68360" BSP
#
# $Id: gen68360.cfg,v 1.2 2001-09-27 12:02:52 chris Exp $
#
 
RTEMS_CPU=m68k
 
ifeq ($(RTEMS_GEN68360_COMPANION_MODE),yes)
RTEMS_CPU_MODEL=m68040
else
RTEMS_CPU_MODEL=mcpu32
endif
 
include $(RTEMS_ROOT)/make/custom/default.cfg
 
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=gen68360
 
#
# You must use versions of gcc and gas that support the -mcpu32 option.
#
ifeq ($(RTEMS_GEN68360_COMPANION_MODE),yes)
CPU_CFLAGS= -m68040
else
CPU_CFLAGS = -mcpu32
endif
 
# optimize flag: typically -0, could use -O4 or -fast
# -O4 is ok for RTEMS
CFLAGS_OPTIMIZE_V=-O4 -fomit-frame-pointer
 
# This section makes the target dependent options file.
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#
 
ifeq ($(RTEMS_GEN68360_COMPANION_MODE),yes)
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
endef
else
define make-target-options
@echo "/* #define NDEBUG 1 */ " >>$@
@echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
@echo "/* #define RTEMS_DEBUG 1 */" >>$@
@echo "#define RTEMS__mcpu32p__ 1" >>$@
endef
endif
 
# The following are definitions of make-exe which will work using ld as
# is currently required. It is expected that as of gcc 2.8, the end user
# will be able to override parts of the compilers specs and link using gcc.
 
ifeq ($(RTEMS_USE_GCC272),yes)
 
# override default location of Standard C Library
LIBC_LIBC=$(RTEMS_LIBC_DIR)/lib/m68000/msoft-float/libc.a
LIBC_LIBM=$(RTEMS_LIBC_DIR)/lib/m68000/msoft-float/libm.a
 
define make-exe
@ echo
@ echo "WARNING: newlib may use bit test instructions!!"
@ echo
$(LD) $(LDFLAGS) -N -T $(LINKCMDS) -o $(basename $@).exe \
$(START_FILE) $(LINK_OBJS) --start-group $(LINK_LIBS) --end-group
$(NM) -g -n $(basename $@).exe > $(basename $@).num
$(SIZE) $(basename $@).exe
endef
else
 
define make-exe
$(LINK.c) $(AM_CFLAGS) $(AM_LDFLAGS) -o $@ \
$(LINK_OBJS) $(LINK_LIBS)
$(NM) -g -n $@ > $(basename $@).num
$(SIZE) $@
endef
endif
 
 
# Miscellaneous additions go here

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.