URL
https://opencores.org/ocsvn/rs232_interface/rs232_interface/trunk
Subversion Repositories rs232_interface
Compare Revisions
- This comparison shows the changes necessary to convert path
/rs232_interface
- from Rev 10 to Rev 11
- ↔ Reverse comparison
Rev 10 → Rev 11
/trunk/uart.vhd
47,6 → 47,7
signal rx_clk_en : std_logic; -- Received clock enable |
signal rx_rcv_init : std_logic; -- Start of reception |
signal rx_par_bit : std_logic; -- Calculated Parity bit |
signal rx_data_deb : std_logic; -- Debounce RX data |
signal rx_data_tmp : std_logic_vector(7 downto 0); -- Serial to parallel converter |
signal rx_data_cnt : std_logic_vector(2 downto 0); -- Count received bits |
|
73,7 → 74,7
end if; |
-- Reset condition |
if rst = RST_LVL then |
tx_clk_en := '0'; |
tx_clk_en <= '0'; |
counter := 0; |
end if; |
end if; |
141,42 → 142,40
end if; |
end process; |
|
rx_start_detect:process(clk) |
rx_debounceer:process(clk) |
variable deb_buf : std_logic_vector(3 downto 0); |
variable deb_val : std_logic; |
variable deb_old : std_logic; |
begin |
if clk'event and clk = '1' then |
-- Store previous debounce value |
deb_old := deb_val; |
-- Debounce logic |
if deb_buf = "0000" then |
deb_val := '0'; |
rx_data_deb <= '0'; |
elsif deb_buf = "1111" then |
deb_val := '1'; |
rx_data_deb <= '1'; |
end if; |
-- Data storage to debounce |
deb_buf := deb_buf(2 downto 0) & rx; |
deb_buf := deb_buf(2 downto 0) & rx; |
end if; |
end process; |
|
-- Check RX idle state |
if rx_fsm = idle then |
-- Falling edge detection |
if deb_old = '1' and deb_val = '0' then |
rx_rcv_init <= '1'; |
end if; |
-- Default assignments |
rx_start_detect:process(clk) |
variable rx_data_old : std_logic; |
begin |
if clk'event and clk = '1' then |
-- Falling edge detection |
if rx_data_old = '1' and rx_data_deb = '0' then |
rx_rcv_init <= '1'; |
else |
rx_rcv_init <= '0'; |
end if; |
-- Default assignments |
rx_data_old := rx_data_deb; |
-- Reset condition |
if rst = RST_LVL then |
deb_old := '0'; |
deb_val := '0'; |
deb_buf <= (others=>'0'); |
rx_data_old := '0'; |
rx_rcv_init <= '0'; |
end if; |
end if; |
end if; |
end process; |
|
|
rx_clk_gen:process(clk) |
184,7 → 183,7
begin |
if clk'event and clk = '1' then |
-- Normal Operation |
if counter = (CLK_FREQ*1_000_000)/SER_FREQ-1 and rx_rcv_init = '1' then |
if counter = (CLK_FREQ*1_000_000)/SER_FREQ-1 or rx_rcv_init = '1' then |
rx_clk_en <= '1'; |
counter := 0; |
else |
202,14 → 201,15
rx_proc:process(clk) |
begin |
if clk'event and clk = '1' then |
-- Default values |
rx_ready <= '0'; |
-- Enable on UART rate |
if rx_clk_en = '1' then |
-- Default values |
rx_ready <= '0'; |
-- FSM description |
case rx_fsm is |
-- Wait to transfer data |
when idle => |
if rx_rcv_init = '1' then |
if rx_data_deb = UART_START then |
rx_fsm <= data; |
end if; |
rx_par_bit <= '0'; |