OpenCores
URL https://opencores.org/ocsvn/ttl_library/ttl_library/trunk

Subversion Repositories ttl_library

Compare Revisions

  • This comparison shows the changes necessary to convert path 
    /ttl_library/trunk
    from Rev 4 to Rev 5
    ↔ Reverse comparison
  •

Rev 4 → Rev 5

/Memories.vhd
0,0 → 1,606
-----------------------------------------------------------------------
-- Static RAM models (VHDL) --
-- David R Brooks --
-- December, 2016. Perth, Australia --
-- Compliance: VHDL 2008 --
-- NB Simulation only: they are NOT synthesizable. --
-- Based on: Manufacturers data sheets --
-- Pinouts & naming agree with Altium libraries & VHDL netlister. --
-- See StaticRAM.vhd --
-----------------------------------------------------------------------
 
-- NB The Hamburg SRAM component has been altered, splitting the bidirectional
-- data bus into separate IN & OUT parts. This is needed so that the bidirectional
-- data bus can be exported from these wrapper components.
 
-----------------------------------------------------------------------
-- HM6116: 2K x 8 CMOS static RAM (70 ns)
-- Verified 28/12/2016
-----------------------------------------------------------------------
library ieee;
use ieee.std_logic_1164.all;
 
use work.LSTTL.all;
use work.TTLPrivate.all;
use work.Memories.all;
 
entity HM6116 is
generic(
fname : String := ""; -- Name of initialisation file (if any)
-- min max
tRC : time := 70 ns; -- Read cycle (not used)
tAA : time := 70 ns; -- Address access
tACS : time := 70 ns; -- Chip select access
tAOE : time := 30 ns; -- OE\ to output valid
tCLZ : time := 5 ns; -- CS\ to output valid
tOLZ : time := 5 ns; -- OE\ to output valid
tCHZ : time := 20 ns; -- CS to output Hi-Z
tOHZR : time := 20 ns; -- OE to output Hi-Z
tOH : time := 3 ns; -- OP hold from addr change
tWC : time := 70 ns; -- Write cycle
tCW : time := 70 ns; -- CS to end of write
tAW : time := 70 ns; -- Address valid to end of write
tAS : time := 0 ns; -- Address setup time
tDS : time := 0 ns; -- Data setup time
tWP : time := 50 ns; -- Write pulse width
tWR : time := 0 ns; -- Write recovery time
tDW : time := 30 ns; -- Data valid to end of write
tDH : time := 0 ns; -- Data hold from end of write
tWHZ : time := 25 ns; -- Write to OP Hi-Z
tWLZ : time := 5 ns; -- Write to OP Lo-Z (not used)
tOHZW : time := 30 ns; -- OE to OP Hi-Z
tOW : time := 5 ns -- OP active from end of write
);
port(
X_1 : in std_logic; -- A7
X_2 : in std_logic; -- A6
X_3 : in std_logic; -- A5
X_4 : in std_logic; -- A4
X_5 : in std_logic; -- A3
X_6 : in std_logic; -- A2
X_7 : in std_logic; -- A1
X_8 : in std_logic; -- A0
X_9 : inout std_logic; -- IO0
X_10 : inout std_logic; -- IO1
X_11 : inout std_logic; -- IO2
X_12 : inout std_logic; -- GND
X_13 : inout std_logic; -- IO3
X_14 : inout std_logic; -- IO4
X_15 : inout std_logic; -- IO5
X_16 : inout std_logic; -- IO6
X_17 : inout std_logic; -- IO7
X_18 : in std_logic; -- CS\
X_19 : in std_logic; -- A10
X_20 : in std_logic; -- OE\
X_21 : in std_logic; -- WE\
X_22 : in std_logic; -- A9
X_23 : in std_logic; -- A8
X_24 : inout std_logic -- Vcc
);
end entity HM6116;
 
architecture BEHAV of HM6116 is
signal D, Q : std_logic_vector( 7 downto 0);
signal A : std_logic_vector(10 downto 0);
alias nCE is X_18;
alias nOE is X_20;
alias nWE is X_21;
constant finit : boolean := fname /= ""; -- Initialise at power-up, if file defined
begin
D <= (X_17, X_16, X_15, X_14, X_13, X_11, X_10, X_9);
(X_17, X_16, X_15, X_14, X_13, X_11, X_10, X_9) <= Q;
A <= (X_19, X_22, X_23, X_1, X_2, X_3, X_4, X_5, X_6, X_7, X_8);
MB: sram
generic map(
value_on_power_up => 'U', -- Memory array is filled with this at start
download_on_power_up => finit, -- if TRUE, RAM is downloaded at start of simulation
trace_ram_load => FALSE, -- Echoes the data downloaded to the RAM on the screen
enable_nWE_only_control => FALSE, -- Read-/write access controlled by nWE only
 
-- READ-cycle timing parameters
tAA_max => tAA, -- Address Access Time
tOHA_min => tOH, -- Output Hold Time
tACE_max => tACS, -- nCE/CE2 Access Time
tDOE_max => tAOE, -- nOE Access Time
tLZOE_min => tOLZ, -- nOE to Low-Z Output
tHZOE_max => tOHZW, -- OE to High-Z Output
tLZCE_min => tCLZ, -- nCE/CE2 to Low-Z Output
tHZCE_max => tCHZ, -- CE/nCE2 to High Z Output
-- WRITE-cycle timing parameters
tWC_min => tWC, -- Write Cycle Time
tSCE_min => tCW, -- nCE/CE2 to Write End
tAW_min => tAW, -- tAW Address Set-up Time to Write End
tHA_min => tWR, -- tHA Address Hold from Write End
tSA_min => tAS, -- Address Set-up Time
tPWE_min => tWP, -- nWE Pulse Width
tSD_min => tDW, -- Data Set-up to Write End
tHD_min => tDH, -- Data Hold from Write End
tHZWE_max => tWHZ, -- nWE Low to High-Z Output
tLZWE_min => tOW -- nWE High to Low-Z Output
)
port map(
nCE => nCE, -- low-active Chip-Enable of the SRAM device; defaults to '1' (inactive)
nOE => nOE, -- low-active Output-Enable of the SRAM device; defaults to '1' (inactive)
nWE => nWE, -- low-active Write-Enable of the SRAM device; defaults to '1' (inactive)
A => A, -- address bus of the SRAM device
D => D, -- data bus to the SRAM device
Q => Q, -- data bus from the SRAM device
CE2 => '1', -- high-active Chip-Enable of the SRAM device; defaults to '1' (active)
download => FALSE, -- A FALSE-to-TRUE transition on this signal downloads the data
download_filename => fname, -- name of the download source file
dump => FALSE, -- A FALSE-to-TRUE transition on this signal dumps data
dump_start => 0, -- Written to the dump-file are the memory words from memory address
dump_end => 0, -- dump_start to address dump_end (default: all addresses)
dump_filename => "" -- name of the dump destination file
);
end architecture BEHAV;
-----------------------------------------------------------------------
-- IS61C1024: 128K x 8 CMOS static RAM (ISSI) (20 ns)
-- Verified 28/12/2016
-----------------------------------------------------------------------
library ieee;
use ieee.std_logic_1164.all;
 
use work.LSTTL.all;
use work.TTLPrivate.all;
use work.Memories.all;
 
entity IS61C1024 is
generic(
fname : String := ""; -- Name of initialisation file (if any)
-- Read Cycle Min. Max. Unit Parameter
tRC : time := 20 ns; -- Read Cycle Time
tAA : time := 20 ns; -- Address Access Time
tOHA : time := 3 ns; -- Output Hold Time
tACE1 : time := 20 ns; -- CE1 Access Time
tACE2 : time := 20 ns; -- CE2 Access Time
tDOE : time := 9 ns; -- Access Time
tLZOE : time := 0 ns; -- OE to Low-Z Output
tHZOE : time := 7 ns; -- OE to High-Z Output
tLZCE1 : time := 3 ns; -- CE1 to Low-Z Output
tLZCE2 : time := 3 ns; -- CE2 to Low-Z Output
tHZCE : time := 9 ns; -- CE1 or CE2 to High-Z Output
tPU : time := 0 ns; -- CE1 or CE2 to Power-Up
tPD : time := 18 ns; -- CE1 or CE2 to Power-Down
-- Write Cycle Min. Max. Unit Parameter
tWC : time := 20 ns; -- Write Cycle Time
tSCE1 : time := 15 ns; -- CE1 to Write End
tSCE2 : time := 15 ns; -- CE2 to Write End
tAW : time := 15 ns; -- Address Setup Time to Write End
tHA : time := 0 ns; -- Address Hold from Write End
tSA : time := 0 ns; -- Address Setup Time
tPWE : time := 12 ns; -- WE Pulse Width
tSD : time := 10 ns; -- Data Setup to Write End
tHD : time := 0 ns; -- Data Hold from Write End
tHZWE : time := 10 ns; -- WE LOW to High-Z Output
tLZWE : time := 2 ns -- WE HIGH to Low-Z Output
);
port(
-- X_1
X_2 : in std_logic; -- A16
X_3 : in std_logic; -- A14
X_4 : in std_logic; -- A12
X_5 : in std_logic; -- A7
X_6 : in std_logic; -- A6
X_7 : in std_logic; -- A5
X_8 : in std_logic; -- A4
X_9 : in std_logic; -- A3
X_10 : in std_logic; -- A2
X_11 : in std_logic; -- A1
X_12 : in std_logic; -- A0
X_13 : inout std_logic; -- IO0
X_14 : inout std_logic; -- IO1
X_15 : inout std_logic; -- IO2
X_16 : inout std_logic; -- GND
X_17 : inout std_logic; -- IO3
X_18 : inout std_logic; -- IO4
X_19 : inout std_logic; -- IO5
X_20 : inout std_logic; -- IO6
X_21 : inout std_logic; -- IO7
X_22 : in std_logic; -- CE1\
X_23 : in std_logic; -- A10
X_24 : in std_logic; -- OE\
X_25 : in std_logic; -- A11
X_26 : in std_logic; -- A9
X_27 : in std_logic; -- A8
X_28 : in std_logic; -- A13
X_29 : in std_logic; -- WE\
X_30 : in std_logic; -- CE2
X_31 : in std_logic; -- A15
X_32 : inout std_logic -- Vcc
);
end entity IS61C1024;
architecture BEHAV of IS61C1024 is
signal D, Q : std_logic_vector( 7 downto 0);
signal A : std_logic_vector(16 downto 0);
alias nCE1 is X_22;
alias CE2 is X_30;
alias nOE is X_24;
alias nWE is X_29;
constant finit : boolean := fname /= ""; -- Initialise at power-up, if file defined
begin
(X_21, X_20, X_19, X_18, X_17, X_15, X_14, X_13) <= Q; -- Bidirectional bus
D <= (X_21, X_20, X_19, X_18, X_17, X_15, X_14, X_13);
A <= (X_2, X_31, X_3, X_28, X_4, X_25, X_23, X_26, X_27, X_5, X_6, X_7, X_8, X_9, X_10, X_11, X_12);
MB: sram
generic map(
value_on_power_up => 'U', -- Memory array is filled with this at start
download_on_power_up => finit, -- if TRUE, RAM is downloaded at start of simulation
trace_ram_load => FALSE, -- Echoes the data downloaded to the RAM on the screen
enable_nWE_only_control => FALSE, -- Read-/write access controlled by nWE only
 
-- READ-cycle timing parameters
tAA_max => tAA, -- Address Access Time
tOHA_min => tOHA, -- Output Hold Time
tACE_max => tACE1, -- nCE/CE2 Access Time
tDOE_max => tDOE, -- nOE Access Time
tLZOE_min => tLZOE, -- nOE to Low-Z Output
tHZOE_max => tHZOE, -- OE to High-Z Output
tLZCE_min => tLZCE1, -- nCE/CE2 to Low-Z Output
tHZCE_max => tHZCE, -- CE/nCE2 to High Z Output
-- WRITE-cycle timing parameters
tWC_min => tWC, -- Write Cycle Time
tSCE_min => tSCE1, -- nCE/CE2 to Write End
tAW_min => tAW, -- tAW Address Set-up Time to Write End
tHA_min => tHA, -- tHA Address Hold from Write End
tSA_min => tSA, -- Address Set-up Time
tPWE_min => tPWE, -- nWE Pulse Width
tSD_min => tSD, -- Data Set-up to Write End
tHD_min => tHD, -- Data Hold from Write End
tHZWE_max => tHZWE, -- nWE Low to High-Z Output
tLZWE_min => tLZWE -- nWE High to Low-Z Output
)
port map(
nCE => nCE1, -- low-active Chip-Enable of the SRAM device; defaults to '1' (inactive)
nOE => nOE, -- low-active Output-Enable of the SRAM device; defaults to '1' (inactive)
nWE => nWE, -- low-active Write-Enable of the SRAM device; defaults to '1' (inactive)
A => A, -- address bus of the SRAM device
D => D, -- data bus to the SRAM device
Q => Q, -- data bus from the SRAM device
CE2 => CE2, -- high-active Chip-Enable of the SRAM device; defaults to '1' (active)
download => FALSE, -- A FALSE-to-TRUE transition on this signal downloads the data
download_filename => fname, -- name of the download source file
dump => FALSE, -- A FALSE-to-TRUE transition on this signal dumps data
dump_start => 0, -- Written to the dump-file are the memory words from memory address
dump_end => 0, -- dump_start to address dump_end (default: all addresses)
dump_filename => "" -- name of the dump destination file
);
end architecture BEHAV;
-----------------------------------------------------------------------
-- MB84256A-10LL : 32K x 8 CMOS static RAM (Fujitsu)
-- Verified 28/12/2016
-----------------------------------------------------------------------
library ieee;
use ieee.std_logic_1164.all;
 
use work.LSTTL.all;
use work.TTLPrivate.all;
use work.Memories.all;
 
entity MB84256 is
generic(
fname : String := ""; -- Name of initialisation file (if any)
-- Read Cycle Min Max
tRC : time := 100 ns; -- Read cycle time
tAA : time := 100 ns; -- Address access time
tACS : time := 100 ns; -- nCS1 access time
tOE : time := 40 ns; -- Output enable to output valid
tOH : time := 20 ns; -- Output hold from address change
tCLZ : time := 10 ns; -- Chip select to output Lo-Z
tOLZ : time := 5 ns; -- Output enable to output Lo-Z
tCHZ : time := 40 ns; -- Chip select to output Hi-Z
tOHZ : time := 40 ns; -- Output enable to output Hi-Z
-- Write Cycle Min Max
tWC : time := 100 ns; -- Write cycle time
tAW : time := 80 ns; -- Address valid to end of write
tCW : time := 80 ns; -- Chip select to end of write
tDW : time := 40 ns; -- Data valid to end of write
tDH : time := 0 ns; -- Data hold time
tWP : time := 60 ns; -- Write pulse width
tAS : time := 0 ns; -- Address setup time
tWR : time := 5 ns; -- Write recovery time
tWLZ : time := 5 ns; -- nWE to output Lo-Z
tWHZ : time := 40 ns -- nWE to output Hi-Z
);
port(
X_1 : in std_logic; -- A14
X_2 : in std_logic; -- A12
X_3 : in std_logic; -- A7
X_4 : in std_logic; -- A6
X_5 : in std_logic; -- A5
X_6 : in std_logic; -- A4
X_7 : in std_logic; -- A3
X_8 : in std_logic; -- A2
X_9 : in std_logic; -- A1
X_10 : in std_logic; -- A0
X_11 : inout std_logic; -- IO0
X_12 : inout std_logic; -- IO1
X_13 : inout std_logic; -- IO2
X_14 : inout std_logic; -- GND
X_15 : inout std_logic; -- IO3
X_16 : inout std_logic; -- IO4
X_17 : inout std_logic; -- IO5
X_18 : inout std_logic; -- IO6
X_19 : inout std_logic; -- IO7
X_20 : in std_logic; -- CS\
X_21 : in std_logic; -- A10
X_22 : in std_logic; -- OE\
X_23 : in std_logic; -- A11
X_24 : in std_logic; -- A9
X_25 : in std_logic; -- A8
X_26 : in std_logic; -- A13
X_27 : in std_logic; -- WE\
X_28 : inout std_logic -- Vcc
);
end entity MB84256;
 
architecture BEHAV of MB84256 is
signal D, Q : std_logic_vector( 7 downto 0);
signal A : std_logic_vector(14 downto 0);
alias nCS is X_20;
alias nOE is X_22;
alias nWE is X_27;
constant finit : boolean := fname /= ""; -- Initialise at power-up, if file defined
begin
(X_19, X_18, X_17, X_16, X_15, X_13, X_12, X_11) <= Q; -- Bidirectional bus
D <= (X_19, X_18, X_17, X_16, X_15, X_13, X_12, X_11);
A <= (X_1, X_26, X_2, X_23, X_21, X_24, X_25, X_3, X_4, X_5, X_6, X_7, X_8, X_9, X_10);
MB: sram
generic map(
value_on_power_up => 'U', -- Memory array is filled with this at start
download_on_power_up => finit, -- if TRUE, RAM is downloaded at start of simulation
trace_ram_load => FALSE, -- Echoes the data downloaded to the RAM on the screen
enable_nWE_only_control => FALSE, -- Read-/write access controlled by nWE only
 
-- READ-cycle timing parameters
tAA_max => tAA, -- Address Access Time
tOHA_min => tOH, -- Output Hold Time
tACE_max => tACS, -- nCE/CE2 Access Time
tDOE_max => tOE, -- nOE Access Time
tLZOE_min => tOLZ, -- nOE to Low-Z Output
tHZOE_max => tOHZ, -- OE to High-Z Output
tLZCE_min => tCLZ, -- nCE/CE2 to Low-Z Output
tHZCE_max => tCHZ, -- CE/nCE2 to High Z Output
-- WRITE-cycle timing parameters
tWC_min => tWC, -- Write Cycle Time
tSCE_min => tCW, -- nCE/CE2 to Write End
tAW_min => tAW, -- tAW Address Set-up Time to Write End
tHA_min => tWR, -- tHA Address Hold from Write End
tSA_min => tAS, -- Address Set-up Time
tPWE_min => tWP, -- nWE Pulse Width
tSD_min => tDW, -- Data Set-up to Write End
tHD_min => tDH, -- Data Hold from Write End
tHZWE_max => tWHZ, -- nWE Low to High-Z Output
tLZWE_min => tWLZ -- nWE High to Low-Z Output
)
port map(
nCE => nCS, -- low-active Chip-Enable of the SRAM device; defaults to '1' (inactive)
nOE => nOE, -- low-active Output-Enable of the SRAM device; defaults to '1' (inactive)
nWE => nWE, -- low-active Write-Enable of the SRAM device; defaults to '1' (inactive)
A => A, -- address bus of the SRAM device
D => D, -- data bus to the SRAM device
Q => Q, -- data bus from the SRAM device
CE2 => '1', -- high-active Chip-Enable of the SRAM device; defaults to '1' (active)
download => FALSE, -- A FALSE-to-TRUE transition on this signal downloads the data
download_filename => fname, -- name of the download source file
dump => FALSE, -- A FALSE-to-TRUE transition on this signal dumps data
dump_start => 0, -- Written to the dump-file are the memory words from memory address
dump_end => 0, -- dump_start to address dump_end (default: all addresses)
dump_filename => "" -- name of the dump destination file
);
end architecture BEHAV;
-----------------------------------------------------------------------
-- CY7C1021-V33: 64K x 16 CMOS static RAM (Cypress)
-----------------------------------------------------------------------
library ieee;
use ieee.std_logic_1164.all;
 
use work.LSTTL.all;
use work.TTLPrivate.all;
use work.Memories.all;
 
entity CY7C1021 is
generic(
fnevn : String := ""; -- Name of even-byte initialisation file (if any)
fnodd : String := ""; -- Name of odd-byte initialisation file (if any)
-- READ CYCLE Min Max
tRC : time := 10 ns; -- Read Cycle Time
tAA : time := 10 ns; -- Address to Data Valid
tOHA : time := 3 ns; -- Data Hold from Address Change
tACE : time := 10 ns; -- CE LOW to Data Valid
tDOE : time := 5 ns; -- OE LOW to Data Valid
tLZOE : time := 0 ns; -- OE LOW to Low Z
tHZOE : time := 5 ns; -- OE HIGH to High Z
tLZCE : time := 3 ns; -- CE LOW to Low Z
tHZCE : time := 5 ns; -- CE HIGH to High Z
tPU : time := 0 ns; -- CE LOW to Power-Up
tPD : time := 10 ns; -- CE HIGH to Power-Down
tDBE : time := 5 ns; -- Byte Enable to Data Valid
tLZBE : time := 0 ns; -- Byte Enable to Low Z
tHZBE : time := 5 ns; -- Byte Disable to High Z
-- WRITE CYCLE
tWC : time := 10 ns; -- Write Cycle Time
tSCE : time := 8 ns; -- CE LOW to Write End
tAW : time := 7 ns; -- Address Set-Up to Write End
tHA : time := 0 ns; -- Address Hold from Write End
tSA : time := 0 ns; -- Address Set-Up to Write Start
tPWE : time := 7 ns; -- WE Pulse Width
tSD : time := 5 ns; -- Data Set-Up to Write End
tHD : time := 0 ns; -- Data Hold from Write End
tLZWE : time := 3 ns; -- WE HIGH to Low Z
tHZWE : time := 5 ns; -- WE LOW to High Z
tBW : time := 7 ns -- Byte Enable to End of Write
);
port(
X_1 : in std_logic; -- A4
X_2 : in std_logic; -- A3
X_3 : in std_logic; -- A2
X_4 : in std_logic; -- A1
X_5 : in std_logic; -- A0
X_6 : in std_logic; -- CE\
X_7 : inout std_logic; -- IO0
X_8 : inout std_logic; -- IO1
X_9 : inout std_logic; -- IO2
X_10 : inout std_logic; -- IO3
X_11 : inout std_logic; -- Vcc
X_12 : inout std_logic; -- GND
X_13 : inout std_logic; -- IO4
X_14 : inout std_logic; -- IO5
X_15 : inout std_logic; -- IO6
X_16 : inout std_logic; -- IO7
X_17 : in std_logic; -- WE\
X_18 : inout std_logic; -- A15
X_19 : inout std_logic; -- A14
X_20 : inout std_logic; -- A13
X_21 : inout std_logic; -- A12
-- X_22
-- X_23
X_24 : in std_logic; -- A11
X_25 : in std_logic; -- A10
X_26 : in std_logic; -- A9
X_27 : in std_logic; -- A8
-- X_28
X_29 : inout std_logic; -- IO8
X_30 : inout std_logic; -- IO9
X_31 : inout std_logic; -- IO10
X_32 : inout std_logic; -- IO11
X_33 : inout std_logic; -- VCC
X_34 : inout std_logic; -- GND
X_35 : inout std_logic; -- IO12
X_36 : inout std_logic; -- IO13
X_37 : inout std_logic; -- IO14
X_38 : inout std_logic; -- IO15
X_39 : in std_logic; -- BLE\
X_40 : in std_logic; -- BHE\
X_41 : in std_logic; -- OE\
X_42 : in std_logic; -- A7
X_43 : in std_logic; -- A6
X_44 : in std_logic -- A5
);
end entity CY7C1021;
 
architecture BEHAV of CY7C1021 is
signal D1, Q1, D2, Q2 : std_logic_vector( 7 downto 0);
signal AD : std_logic_vector(15 downto 0);
signal CE1, CE2 : std_logic;
 
constant finitE : boolean := fnevn /= ""; -- Initialise at power-up, if file defined
constant finitO : boolean := fnodd /= "";
alias nCE is X_6;
alias nWE is X_17;
alias nBLE is X_39;
alias nBHE is X_40;
alias nOE is X_41;
begin
(X_16, X_15, X_14, X_13, X_10, X_9, X_8, X_7 ) <= Q1; -- Bidirectional bus
D1 <= (X_16, X_15, X_14, X_13, X_10, X_9, X_8, X_7 );
(X_38, X_37, X_36, X_35, X_32, X_31, X_30, X_29) <= Q2; -- Bidirectional bus
D2 <= (X_38, X_37, X_36, X_35, X_32, X_31, X_30, X_29);
AD <= (X_18, X_19, X_20, X_21, X_24, X_25, X_26, X_27,
X_42, X_43, X_44, X_1, X_2, X_3, X_4, X_5 );
CE1 <= not nBLE;
CE2 <= not nBHE;
LB: sram -- Generic RAM component
generic map(
value_on_power_up => 'U', -- Memory array is filled with this at start
download_on_power_up => finitE, -- if TRUE, RAM is downloaded at start of simulation
trace_ram_load => false, -- Echoes the data downloaded to the RAM on the screen
enable_nWE_only_control => false, -- Read-/write access controlled by nWE only
-- READ-cycle timing parameters
tAA_max => tAA, -- Address Access Time
tOHA_min => tOHA, -- Output Hold Time
tACE_max => tACE, -- nCE/CE2 Access Time
tDOE_max => tDOE, -- nOE Access Time
tLZOE_min => tLZOE, -- nOE to Low-Z Output
tHZOE_max => tHZOE, -- OE to High-Z Output
tLZCE_min => tLZCE, -- nCE/CE2 to Low-Z Output
tHZCE_max => tHZCE, -- CE/nCE2 to High Z Output
-- WRITE-cycle timing parameters
tWC_min => tWC, -- Write Cycle Time
tSCE_min => tSCE, -- nCE/CE2 to Write End
tAW_min => tAW, -- tAW Address Set-up Time to Write End
tHA_min => tHA, -- tHA Address Hold from Write End
tSA_min => tSA, -- Address Set-up Time
tPWE_min => tPWE, -- nWE Pulse Width
tSD_min => tSD, -- Data Set-up to Write End
tHD_min => tHD, -- Data Hold from Write End
tHZWE_max => tHZWE, -- nWE Low to High-Z Output
tLZWE_min => tLZWE -- nWE High to Low-Z Output
)
port map(
nCE => nCE, -- low-active Chip-Enable of the SRAM device; defaults to '1' (inactive)
nOE => nOE, -- low-active Output-Enable of the SRAM device; defaults to '1' (inactive)
nWE => nWE, -- low-active Write-Enable of the SRAM device; defaults to '1' (inactive)
A => AD, -- address bus of the SRAM device
D => D1, -- data bus to the SRAM device
Q => Q1, -- data bus from the SRAM device
CE2 => CE1, -- high-active Chip-Enable of the SRAM device; defaults to '1' (active)
download => false, -- A FALSE-to-TRUE transition on this signal downloads the data
download_filename => "fnevn" -- name of the download source file
);
 
HB: sram -- Generic RAM component
generic map(
value_on_power_up => 'U', -- Memory array is filled with this at start
download_on_power_up => finitO, -- if TRUE, RAM is downloaded at start of simulation
trace_ram_load => false, -- Echoes the data downloaded to the RAM on the screen
enable_nWE_only_control => false, -- Read-/write access controlled by nWE only
-- READ-cycle timing parameters
tAA_max => tAA, -- Address Access Time
tOHA_min => tOHA, -- Output Hold Time
tACE_max => tACE, -- nCE/CE2 Access Time
tDOE_max => tDOE, -- nOE Access Time
tLZOE_min => tLZOE, -- nOE to Low-Z Output
tHZOE_max => tHZOE, -- OE to High-Z Output
tLZCE_min => tLZCE, -- nCE/CE2 to Low-Z Output
tHZCE_max => tHZCE, -- CE/nCE2 to High Z Output
-- WRITE-cycle timing parameters
tWC_min => tWC, -- Write Cycle Time
tSCE_min => tSCE, -- nCE/CE2 to Write End
tAW_min => tAW, -- tAW Address Set-up Time to Write End
tHA_min => tHA, -- tHA Address Hold from Write End
tSA_min => tSA, -- Address Set-up Time
tPWE_min => tPWE, -- nWE Pulse Width
tSD_min => tSD, -- Data Set-up to Write End
tHD_min => tHD, -- Data Hold from Write End
tHZWE_max => tHZWE, -- nWE Low to High-Z Output
tLZWE_min => tLZWE -- nWE High to Low-Z Output
)
port map(
nCE => nCE, -- low-active Chip-Enable of the SRAM device; defaults to '1' (inactive)
nOE => nOE, -- low-active Output-Enable of the SRAM device; defaults to '1' (inactive)
nWE => nWE, -- low-active Write-Enable of the SRAM device; defaults to '1' (inactive)
A => AD, -- address bus of the SRAM device
D => D2, -- data bus to the SRAM device
Q => Q2, -- data bus from the SRAM device
CE2 => CE2, -- high-active Chip-Enable of the SRAM device; defaults to '1' (active)
download => false, -- A FALSE-to-TRUE transition on this signal downloads the data
download_filename => "fnodd" -- name of the download source file
);
end architecture BEHAV;

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.