URL
https://opencores.org/ocsvn/udp_ip_stack/udp_ip_stack/trunk
Subversion Repositories udp_ip_stack
Compare Revisions
- This comparison shows the changes necessary to convert path
/udp_ip_stack/tags/v2.0/bench/vhdl
- from Rev 11 to Rev 12
- ↔ Reverse comparison
Rev 11 → Rev 12
/IP_av2_complete_nomac_tb .vhd
0,0 → 1,451
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 13:54:32 06/04/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/ip1/IP_complete_nomac_tb.vhd |
-- Project Name: ip1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: IP_complete_nomac |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
LIBRARY ieee; |
USE ieee.std_logic_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use work.axi.all; |
use work.ipv4_types.all; |
use work.arp_types.all; |
use work.arp; |
use work.arpv2; |
|
|
ENTITY IP_av2_complete_nomac_tb IS |
END IP_av2_complete_nomac_tb; |
|
|
|
--configuration main of IP_av2_complete_nomac_tb is |
-- for behavior |
-- for uut : IP_complete_nomac |
-- use configuration work.IP_complete_nomac.multi_slot_arp; |
-- end for; |
-- end for; |
--end main; |
|
ARCHITECTURE behavior OF IP_av2_complete_nomac_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT IP_complete_nomac |
generic ( |
CLOCK_FREQ : integer := 125000000; -- freq of data_in_clk -- needed to timout cntr |
ARP_TIMEOUT : integer := 60 -- ARP response timeout (s) |
); |
Port ( |
-- IP Layer signals |
ip_tx_start : in std_logic; |
ip_tx : in ipv4_tx_type; -- IP tx cxns |
ip_tx_result : out std_logic_vector (1 downto 0); -- tx status (changes during transmission) |
ip_tx_data_out_ready : out std_logic; -- indicates IP TX is ready to take data |
ip_rx_start : out std_logic; -- indicates receipt of ip frame. |
ip_rx : out ipv4_rx_type; |
-- system signals |
rx_clk : in STD_LOGIC; |
tx_clk : in STD_LOGIC; |
reset : in STD_LOGIC; |
our_ip_address : in STD_LOGIC_VECTOR (31 downto 0); |
our_mac_address : in std_logic_vector (47 downto 0); |
control : in ip_control_type; |
-- status signals |
arp_pkt_count : out STD_LOGIC_VECTOR(7 downto 0); -- count of arp pkts received |
ip_pkt_count : out STD_LOGIC_VECTOR(7 downto 0); -- number of IP pkts received for us |
-- MAC Transmitter |
mac_tx_tdata : out std_logic_vector(7 downto 0); -- data byte to tx |
mac_tx_tvalid : out std_logic; -- tdata is valid |
mac_tx_tready : in std_logic; -- mac is ready to accept data |
mac_tx_tfirst : out std_logic; -- indicates first byte of frame |
mac_tx_tlast : out std_logic; -- indicates last byte of frame |
-- MAC Receiver |
mac_rx_tdata : in std_logic_vector(7 downto 0); -- data byte received |
mac_rx_tvalid : in std_logic; -- indicates tdata is valid |
mac_rx_tready : out std_logic; -- tells mac that we are ready to take data |
mac_rx_tlast : in std_logic -- indicates last byte of the trame |
); |
END COMPONENT; |
|
|
--Inputs |
signal ip_tx_start : std_logic := '0'; |
signal ip_tx : ipv4_tx_type; |
|
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal our_ip_address : std_logic_vector(31 downto 0) := (others => '0'); |
signal our_mac_address : std_logic_vector(47 downto 0) := (others => '0'); |
signal mac_tx_tready : std_logic := '0'; |
signal mac_rx_tdata : std_logic_vector(7 downto 0) := (others => '0'); |
signal mac_rx_tvalid : std_logic := '0'; |
signal mac_rx_tlast : std_logic := '0'; |
signal control : ip_control_type; |
|
--Outputs |
signal ip_tx_result : std_logic_vector (1 downto 0); -- tx status (changes during transmission) |
signal ip_tx_data_out_ready : std_logic; -- indicates IP TX is ready to take data |
signal ip_rx_start : std_logic; |
signal ip_rx : ipv4_rx_type; |
signal arp_pkt_count : std_logic_vector(7 downto 0); |
signal mac_tx_tdata : std_logic_vector(7 downto 0); |
signal mac_tx_tvalid : std_logic; |
signal mac_tx_tfirst : std_logic; |
signal mac_tx_tlast : std_logic; |
signal mac_rx_tready : std_logic; |
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: IP_complete_nomac PORT MAP ( |
ip_tx_start => ip_tx_start, |
ip_tx => ip_tx, |
ip_tx_result => ip_tx_result, |
ip_tx_data_out_ready => ip_tx_data_out_ready, |
ip_rx_start => ip_rx_start, |
ip_rx => ip_rx, |
rx_clk => clk, |
tx_clk => clk, |
reset => reset, |
our_ip_address => our_ip_address, |
our_mac_address => our_mac_address, |
control => control, |
arp_pkt_count => arp_pkt_count, |
mac_tx_tdata => mac_tx_tdata, |
mac_tx_tvalid => mac_tx_tvalid, |
mac_tx_tready => mac_tx_tready, |
mac_tx_tfirst => mac_tx_tfirst, |
mac_tx_tlast => mac_tx_tlast, |
mac_rx_tdata => mac_rx_tdata, |
mac_rx_tvalid => mac_rx_tvalid, |
mac_rx_tready => mac_rx_tready, |
mac_rx_tlast => mac_rx_tlast |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '1'; |
wait for clk_period/2; |
clk <= '0'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 80 ns; |
|
our_ip_address <= x"c0a80509"; -- 192.168.5.9 |
our_mac_address <= x"002320212223"; |
control.arp_controls.clear_cache <= '0'; |
ip_tx_start <= '0'; |
mac_tx_tready <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
-- check reset conditions |
assert ip_tx_result = IPTX_RESULT_NONE report "ip_tx_result not initialised correctly on reset"; |
assert ip_tx_data_out_ready = '0' report "ip_tx_data_out_ready not initialised correctly on reset"; |
assert mac_tx_tvalid = '0' report "mac_tx_tvalid not initialised correctly on reset"; |
assert mac_tx_tlast = '0' report " mac_tx_tlast not initialised correctly on reset"; |
assert arp_pkt_count = x"00" report " arp_pkt_count not initialised correctly on reset"; |
assert ip_rx_start = '0' report "ip_rx_start not initialised correctly on reset"; |
assert ip_rx.hdr.is_valid = '0' report "ip_rx.hdr.is_valid not initialised correctly on reset"; |
assert ip_rx.hdr.protocol = x"00" report "ip_rx.hdr.protocol not initialised correctly on reset"; |
assert ip_rx.hdr.data_length = x"0000" report "ip_rx.hdr.data_length not initialised correctly on reset"; |
assert ip_rx.hdr.src_ip_addr = x"00000000" report "ip_rx.hdr.src_ip_addr not initialised correctly on reset"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "ip_rx.hdr.num_frame_errors not initialised correctly on reset"; |
assert ip_rx.data.data_in = x"00" report "ip_rx.data.data_in not initialised correctly on reset"; |
assert ip_rx.data.data_in_valid = '0' report "ip_rx.data.data_in_valid not initialised correctly on reset"; |
assert ip_rx.data.data_in_last = '0' report "ip_rx.data.data_in_last not initialised correctly on reset"; |
|
-- insert stimulus here |
|
------------ |
-- TEST 1 -- basic functional rx test with received ip pkt |
------------ |
|
report "T1: Send an eth frame with IP pkt dst ip_address c0a80509, dst mac 002320212223"; |
|
mac_tx_tready <= '1'; |
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
|
-- user data |
mac_rx_tdata <= x"24"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert ip_rx.hdr.is_valid = '1' report "T1: ip_rx.hdr.is_valid not set"; |
assert ip_rx.hdr.protocol = x"11" report "T1: ip_rx.hdr.protocol not set correctly"; |
assert ip_rx.hdr.data_length = x"0004" report "T1: ip_rx.hdr.data_length not set correctly"; |
assert ip_rx.hdr.src_ip_addr = x"c0a80501" report "T1: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T1: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx.hdr.last_error_code = x"0" report "T1: ip_rx.hdr.last_error_code not set correctly"; |
assert ip_rx_start = '1' report "T1: ip_rx_start not set"; |
assert ip_rx.data.data_in_valid = '1' report "T1: ip_rx.data.data_in_valid not set"; |
|
mac_rx_tdata <= x"25"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"27"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert ip_rx.data.data_in_last = '1' report "T1: ip_rx.data.data_in_last not set"; |
|
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
assert ip_rx.data.data_in_valid = '0' report "T1: ip_rx.data.data_in_valid not cleared"; |
assert ip_rx.data.data_in_last = '0' report "T1: ip_rx.data.data_in_last not cleared"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T1: ip_rx.hdr.num_frame_errors non zero at end of test"; |
assert ip_rx.hdr.last_error_code = x"0" report "T1: ip_rx.hdr.last_error_code indicates error at end of test"; |
assert ip_rx_start = '0' report "T1: ip_rx_start not cleared"; |
|
------------ |
-- TEST 2 -- respond with IP TX |
------------ |
|
report "T2: respond with IP TX"; |
|
ip_tx.hdr.protocol <= x"35"; |
ip_tx.hdr.data_length <= x"0006"; |
ip_tx.hdr.dst_ip_addr <= x"c0123478"; |
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period; |
|
ip_tx_start <= '1'; wait for clk_period; |
|
ip_tx_start <= '0'; wait for clk_period; |
|
assert ip_tx_result = IPTX_RESULT_SENDING report "T2: result should be IPTX_RESULT_SENDING"; |
|
wait for clk_period*2; |
|
assert ip_tx_data_out_ready = '0' report "T2: IP data out ready asserted too early"; |
|
-- need to wait for ARP tx to complete |
|
wait for clk_period*50; |
|
assert mac_tx_tvalid = '0' report "T2: mac_tx_tvalid not cleared after ARP tx"; |
assert mac_tx_tlast = '0' report "T2: mac_tx_tlast not cleared after ARP tx"; |
|
-- now create the ARP response (rx) |
|
-- Send the reply |
-- Send an ARP reply: x"c0123478" has mac 02:12:03:23:04:54 |
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"02"; wait for clk_period; |
mac_rx_tdata <= x"12"; wait for clk_period; |
mac_rx_tdata <= x"03"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"04"; wait for clk_period; |
mac_rx_tdata <= x"54"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- HW type |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Protocol type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- HW size |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- protocol size |
mac_rx_tdata <= x"04"; wait for clk_period; |
-- Opcode |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"02"; wait for clk_period; |
-- Sender MAC |
mac_rx_tdata <= x"02"; wait for clk_period; |
mac_rx_tdata <= x"12"; wait for clk_period; |
mac_rx_tdata <= x"03"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"04"; wait for clk_period; |
mac_rx_tdata <= x"54"; wait for clk_period; |
-- Sender IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"12"; wait for clk_period; |
mac_rx_tdata <= x"34"; wait for clk_period; |
mac_rx_tdata <= x"78"; wait for clk_period; |
-- Target MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- Target IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '1'; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
|
wait until ip_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
ip_tx.data.data_out_valid <= '1'; |
ip_tx.data.data_out <= x"56"; wait for clk_period; |
ip_tx.data.data_out <= x"57"; wait for clk_period; |
ip_tx.data.data_out <= x"58"; wait for clk_period; |
ip_tx.data.data_out <= x"59"; wait for clk_period; |
ip_tx.data.data_out <= x"5a"; wait for clk_period; |
|
ip_tx.data.data_out <= x"5b"; |
ip_tx.data.data_out_last <= '1'; |
wait for clk_period; |
|
assert mac_tx_tlast = '1' report "T2: mac_tx_tlast not set on last byte"; |
|
wait for clk_period; |
|
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period*2; |
|
assert ip_tx_result = IPTX_RESULT_SENT report "T2: result should be SENT"; |
wait for clk_period*10; |
|
------------ |
-- TEST 3 -- Check that sending to the same IP addr doesnt cause an ARP req as the addr is cached |
------------ |
|
report "T3: Send 2nd IP TX to same IP addr - should not need to do ARP tx/rx"; |
ip_tx.hdr.protocol <= x"35"; |
ip_tx.hdr.data_length <= x"0006"; |
ip_tx.hdr.dst_ip_addr <= x"c0123478"; |
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period; |
ip_tx_start <= '1'; wait for clk_period; |
ip_tx_start <= '0'; wait for clk_period; |
assert ip_tx_result = IPTX_RESULT_SENDING report "T3: result should be IPTX_RESULT_SENDING"; |
wait for clk_period*2; |
assert ip_tx_data_out_ready = '0' report "T3: IP data out ready asserted too early"; |
wait until ip_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
ip_tx.data.data_out_valid <= '1'; |
ip_tx.data.data_out <= x"81"; wait for clk_period; |
ip_tx.data.data_out <= x"83"; wait for clk_period; |
ip_tx.data.data_out <= x"85"; wait for clk_period; |
ip_tx.data.data_out <= x"87"; wait for clk_period; |
ip_tx.data.data_out <= x"89"; wait for clk_period; |
|
ip_tx.data.data_out <= x"8b"; |
ip_tx.data.data_out_last <= '1'; |
wait for clk_period; |
|
assert mac_tx_tlast = '1' report "T3: mac_tx_tlast not set on last byte"; |
|
wait for clk_period; |
|
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period*2; |
|
assert ip_tx_result = IPTX_RESULT_SENT report "T3: result should be SENT"; |
wait for clk_period*2; |
|
|
|
report "-- end of tests --"; |
|
wait; |
end process; |
|
END; |
/UDP_av2_complete_nomac_tb.vhd
0,0 → 1,1415
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 09:57:01 06/13/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/udp1/UDP_complete_nomac_tb.vhd |
-- Project Name: udp1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: UDP_Complete_nomac |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Revision 0.02 - Added test for IP broadcast tx |
-- Revision 0.03 - Added tests for ARP timeout |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
library IEEE; |
use IEEE.STD_LOGIC_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use work.axi.all; |
use work.ipv4_types.all; |
use work.arp_types.all; |
|
ENTITY UDP_av2_complete_nomac_tb IS |
END UDP_av2_complete_nomac_tb; |
|
ARCHITECTURE behavior OF UDP_av2_complete_nomac_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT UDP_Complete_nomac |
generic ( |
CLOCK_FREQ : integer := 125000000; -- freq of data_in_clk -- needed to timout cntr |
ARP_TIMEOUT : integer := 60 -- ARP response timeout (s) |
); |
Port ( |
-- UDP TX signals |
udp_tx_start : in std_logic; -- indicates req to tx UDP |
udp_txi : in udp_tx_type; -- UDP tx cxns |
udp_tx_result : out std_logic_vector (1 downto 0);-- tx status (changes during transmission) |
udp_tx_data_out_ready: out std_logic; -- indicates udp_tx is ready to take data |
-- UDP RX signals |
udp_rx_start : out std_logic; -- indicates receipt of udp header |
udp_rxo : out udp_rx_type; |
-- IP RX signals |
ip_rx_hdr : out ipv4_rx_header_type; |
-- system signals |
rx_clk : in STD_LOGIC; |
tx_clk : in STD_LOGIC; |
reset : in STD_LOGIC; |
our_ip_address : in STD_LOGIC_VECTOR (31 downto 0); |
our_mac_address : in std_logic_vector (47 downto 0); |
control : in udp_control_type; |
-- status signals |
arp_pkt_count : out STD_LOGIC_VECTOR(7 downto 0); -- count of arp pkts received |
ip_pkt_count : out STD_LOGIC_VECTOR(7 downto 0); -- number of IP pkts received for us |
-- MAC Transmitter |
mac_tx_tdata : out std_logic_vector(7 downto 0); -- data byte to tx |
mac_tx_tvalid : out std_logic; -- tdata is valid |
mac_tx_tready : in std_logic; -- mac is ready to accept data |
mac_tx_tfirst : out std_logic; -- indicates first byte of frame |
mac_tx_tlast : out std_logic; -- indicates last byte of frame |
-- MAC Receiver |
mac_rx_tdata : in std_logic_vector(7 downto 0); -- data byte received |
mac_rx_tvalid : in std_logic; -- indicates tdata is valid |
mac_rx_tready : out std_logic; -- tells mac that we are ready to take data |
mac_rx_tlast : in std_logic -- indicates last byte of the trame |
); |
END COMPONENT; |
|
|
|
type state_type is (IDLE, WAIT_RX_DONE, DATA_OUT); |
type count_mode_type is (RST, INCR, HOLD); |
type set_clr_type is (SET, CLR, HOLD); |
|
|
--Inputs |
signal udp_tx_start_int : std_logic := '0'; |
signal udp_tx_int : udp_tx_type; |
signal clk_int : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal our_ip_address : std_logic_vector(31 downto 0) := (others => '0'); |
signal our_mac_address : std_logic_vector(47 downto 0) := (others => '0'); |
signal mac_tx_tready : std_logic := '0'; |
signal mac_rx_tdata : std_logic_vector(7 downto 0) := (others => '0'); |
signal mac_rx_tvalid : std_logic := '0'; |
signal mac_rx_tlast : std_logic := '0'; |
signal control : udp_control_type; |
|
--Outputs |
signal udp_rx_start_int : std_logic; |
signal udp_rx_int : udp_rx_type; |
signal ip_rx_hdr : ipv4_rx_header_type; |
signal udp_tx_result : std_logic_vector (1 downto 0); |
signal udp_tx_data_out_ready_int: std_logic; |
|
signal arp_pkt_count : std_logic_vector(7 downto 0); |
signal ip_pkt_count : std_logic_vector(7 downto 0); |
signal mac_tx_tdata : std_logic_vector(7 downto 0); |
signal mac_tx_tvalid : std_logic; |
signal mac_tx_tfirst : std_logic; |
signal mac_tx_tlast : std_logic; |
signal mac_rx_tready : std_logic; |
|
signal pbtx_led : std_logic; |
signal pbtx : std_logic := '0'; |
|
-- state signals |
signal state : state_type; |
signal count : unsigned (7 downto 0); |
signal tx_hdr : udp_tx_header_type; |
signal tx_start_reg : std_logic; |
signal tx_started_reg : std_logic; |
signal tx_fin_reg : std_logic; |
|
|
-- control signals |
signal next_state : state_type; |
signal set_state : std_logic; |
signal set_count : count_mode_type; |
signal set_hdr : std_logic; |
signal set_tx_start : set_clr_type; |
signal set_last : std_logic; |
signal set_tx_started : set_clr_type; |
signal set_tx_fin : set_clr_type; |
signal first_byte_rx : STD_LOGIC_VECTOR(7 downto 0); |
|
|
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: UDP_Complete_nomac |
generic map ( |
CLOCK_FREQ => 10, -- artificially low count to enable pragmatic testing |
ARP_TIMEOUT => 20 |
) |
PORT MAP ( |
udp_tx_start => udp_tx_start_int, |
udp_txi => udp_tx_int, |
udp_tx_result => udp_tx_result, |
udp_tx_data_out_ready => udp_tx_data_out_ready_int, |
udp_rx_start => udp_rx_start_int, |
udp_rxo => udp_rx_int, |
ip_rx_hdr => ip_rx_hdr, |
rx_clk => clk_int, |
tx_clk => clk_int, |
reset => reset, |
our_ip_address => our_ip_address, |
our_mac_address => our_mac_address, |
control => control, |
arp_pkt_count => arp_pkt_count, |
ip_pkt_count => ip_pkt_count, |
mac_tx_tdata => mac_tx_tdata, |
mac_tx_tvalid => mac_tx_tvalid, |
mac_tx_tready => mac_tx_tready, |
mac_tx_tfirst => mac_tx_tfirst, |
mac_tx_tlast => mac_tx_tlast, |
mac_rx_tdata => mac_rx_tdata, |
mac_rx_tvalid => mac_rx_tvalid, |
mac_rx_tready => mac_rx_tready, |
mac_rx_tlast => mac_rx_tlast |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk_int <= '0'; |
wait for clk_period/2; |
clk_int <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 100 ns; |
|
our_ip_address <= x"c0a80509"; -- 192.168.5.9 |
our_mac_address <= x"002320212223"; |
control.ip_controls.arp_controls.clear_cache <= '0'; |
mac_tx_tready <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
-- check reset conditions |
assert udp_tx_result = UDPTX_RESULT_NONE report "udp_tx_result not initialised correctly on reset"; |
assert udp_tx_data_out_ready_int = '0' report "ip_udp_txitx.data.data_out_ready not initialised correctly on reset"; |
assert mac_tx_tvalid = '0' report "mac_tx_tvalid not initialised correctly on reset"; |
assert mac_tx_tlast = '0' report "mac_tx_tlast not initialised correctly on reset"; |
assert arp_pkt_count = x"00" report "arp_pkt_count not initialised correctly on reset"; |
assert ip_pkt_count = x"00" report "ip_pkt_count not initialised correctly on reset"; |
assert udp_rx_start_int = '0' report "udp_rx_start not initialised correctly on reset"; |
assert udp_rx_int.hdr.is_valid = '0' report "udp_rx_int.hdr.is_valid not initialised correctly on reset"; |
assert udp_rx_int.hdr.data_length = x"0000" report "udp_rx_int.hdr.data_length not initialised correctly on reset"; |
assert udp_rx_int.hdr.src_ip_addr = x"00000000" report "udp_rx_int.hdr.src_ip_addr not initialised correctly on reset"; |
assert udp_rx_int.hdr.src_port = x"0000" report "udp_rx_int.hdr.src_port not initialised correctly on reset"; |
assert udp_rx_int.hdr.dst_port = x"0000" report "udp_rx_int.hdr.dst_port not initialised correctly on reset"; |
assert udp_rx_int.data.data_in = x"00" report "udp_rx_start.data.data_in not initialised correctly on reset"; |
assert udp_rx_int.data.data_in_valid = '0' report "udp_rx_start.data.data_in_valid not initialised correctly on reset"; |
assert udp_rx_int.data.data_in_last = '0' report "udp_rx_start.data.data_in_last not initialised correctly on reset"; |
assert ip_rx_hdr.is_valid = '0' report "ip_rx_hdr.is_valid not initialised correctly on reset"; |
assert ip_rx_hdr.protocol = x"00" report "ip_rx_hdr.protocol not initialised correctly on reset"; |
assert ip_rx_hdr.data_length = x"0000" report "ip_rx_hdr.data_length not initialised correctly on reset"; |
assert ip_rx_hdr.src_ip_addr = x"00000000" report "ip_rx_hdr.src_ip_addr not initialised correctly on reset"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "ip_rx_hdr.num_frame_errors not initialised correctly on reset"; |
|
|
-- insert stimulus here |
|
------------ |
-- TEST 1 -- send ARP request |
------------ |
|
report "T1: Send an ARP request: who has 192.168.5.9? Tell 192.168.5.1"; |
|
mac_tx_tready <= '1'; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- HW type |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Protocol type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- HW size |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- protocol size |
mac_rx_tdata <= x"04"; wait for clk_period; |
-- Opcode |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Sender MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- Sender IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Target MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- Target IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '1'; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
|
-- check we got the ARP pkt |
assert arp_pkt_count = x"01" report "T1: arp_pkt_count wrong value"; |
assert ip_pkt_count = x"00" report "T1: ip_pkt_count wrong value"; |
assert udp_tx_result = UDPTX_RESULT_NONE report "T1: udp_tx_result wrong value"; |
assert udp_tx_data_out_ready_int = '0' report "T1: ip_udp_txitx.data.data_out_ready wrong value"; |
assert udp_rx_start_int = '0' report "T1: udp_rx_start wrong value"; |
assert udp_rx_int.hdr.is_valid = '0' report "T1: udp_rx_int.hdr.is_valid wrong value"; |
assert ip_rx_hdr.is_valid = '0' report "T1: ip_rx_hdr.is_valid wrong value"; |
|
-- check we tx a response |
|
wait for clk_period*25; |
assert mac_tx_tvalid = '1' report "T1: not transmitting a response"; |
wait for clk_period*25; |
assert mac_tx_tvalid = '0' report "T1: tx held on for too long"; |
|
------------ |
-- TEST 2 -- send UDP pkt (same as sample from Java program) |
------------ |
|
report "T2: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"68"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T2: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T2: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T2: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T2: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T2: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T2: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T2: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T2: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T2: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T2: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T2: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T2: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T2: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T2: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T2: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T2: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T2: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T2: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"01" report "T2: ip pkt cnt incorrect"; |
|
wait for clk_period*20; |
|
------------ |
-- TEST 3 -- send UDP pkt again (same as sample from Java program) |
------------ |
|
report "T3: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"68"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T3: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T3: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T3: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T3: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T3: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T3: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T3: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T3: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T3: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T3: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T3: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T3: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T3: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T3: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T3: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T3: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T3: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T3: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"02" report "T3: ip pkt cnt incorrect"; |
|
wait for clk_period*50; |
|
------------ |
-- TEST 4 -- send UDP pkt with specific UDP data to force a broadcast tx in reply |
------------ |
|
report "T4: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"42"; wait for clk_period; -- First byte 'B' triggers a reply to broadcast addr |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T4: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T4: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T4: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T4: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T4: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T4: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T4: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T4: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T4: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T4: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T4: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T4: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T4: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
report "T4: waiting for mac data tx"; |
wait until mac_tx_tvalid = '1'; |
report "T4: starting mac data tx"; |
wait for clk_period; |
|
-- check the mac data being transmitted |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T4: incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T4: incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T4: incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T4: incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T4: incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T4: incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T4: incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"45" report "T4: incorrect ver.hlen"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect srv type"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect len 0"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T4: incorrect len 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T4: incorrect ident 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect ident 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect flag&frag 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect flag&frag 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"80" report "T4: incorrect TTL"; wait for clk_period; |
assert mac_tx_tdata = x"11" report "T4: incorrect protocol"; wait for clk_period; |
assert mac_tx_tdata = x"75" report "T4: incorrect hdr.cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"1c" report "T4: incorrect hdr.cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T4: incorrect src ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T4: incorrect src ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T4: incorrect src ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T4: incorrect src ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"ff" report "T4: incorrect dst ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"26" report "T4: incorrect src port 0"; wait for clk_period; |
assert mac_tx_tdata = x"94" report "T4: incorrect src port 1"; wait for clk_period; |
assert mac_tx_tdata = x"f4" report "T4: incorrect dst port 0"; wait for clk_period; |
assert mac_tx_tdata = x"9a" report "T4: incorrect dst port 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T4: incorrect udp len 0"; wait for clk_period; |
assert mac_tx_tdata = x"0c" report "T4: incorrect udp len 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect udp cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect udp cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"40" report "T4: incorrect udp data 0"; wait for clk_period; |
assert mac_tx_tdata = x"41" report "T4: incorrect udp data 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"42" report "T4: incorrect udp data 2"; |
assert mac_tx_tlast = '0' report "T4: tlast asserted too soon"; wait for clk_period; |
assert mac_tx_tdata = x"43" report "T4: incorrect udp data 3"; |
assert mac_tx_tlast = '1' report "T4: tlast not asserted"; wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENT report "T4: TX did not complete"; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T4: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T4: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T4: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T4: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T4: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"03" report "T4: ip pkt cnt incorrect"; |
|
------------ |
-- TEST 5 -- send UDP pkt with dst=bc addr to ensure we can receive broadcast tx |
------------ |
|
report "T5: Send UDP IP pkt dst ip_address bc, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"68"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T5: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T5: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T5: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T5: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T5: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T5: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T5: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T5: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T5: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T5: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T5: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T5: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T5: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
|
report "T5: waiting for mac data tx"; |
if mac_tx_tvalid = '0' then |
wait until mac_tx_tvalid = '1'; |
wait for clk_period; |
end if; |
report "T5: starting mac data tx"; |
|
-- check the mac data being transmitted |
assert mac_tx_tdata = x"00" report "T5: incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T5: incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"18" report "T5: incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"29" report "T5: incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"26" report "T5: incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"7c" report "T5: incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T5: incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T5: incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T5: incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T5: incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T5: incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T5: incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T5: incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"45" report "T5: incorrect ver.hlen"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect srv type"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect len 0"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T5: incorrect len 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T5: incorrect ident 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect ident 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect flag&frag 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect flag&frag 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"80" report "T5: incorrect TTL"; wait for clk_period; |
assert mac_tx_tdata = x"11" report "T5: incorrect protocol"; wait for clk_period; |
assert mac_tx_tdata = x"af" report "T5: incorrect hdr.cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"72" report "T5: incorrect hdr.cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T5: incorrect src ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T5: incorrect src ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T5: incorrect src ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T5: incorrect src ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T5: incorrect dst ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T5: incorrect dst ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T5: incorrect dst ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T5: incorrect dst ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"26" report "T5: incorrect src port 0"; wait for clk_period; |
assert mac_tx_tdata = x"94" report "T5: incorrect src port 1"; wait for clk_period; |
assert mac_tx_tdata = x"f4" report "T5: incorrect dst port 0"; wait for clk_period; |
assert mac_tx_tdata = x"9a" report "T5: incorrect dst port 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T5: incorrect udp len 0"; wait for clk_period; |
assert mac_tx_tdata = x"0c" report "T5: incorrect udp len 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect udp cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect udp cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"50" report "T5: incorrect udp data 0"; wait for clk_period; |
assert mac_tx_tdata = x"51" report "T5: incorrect udp data 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"52" report "T5: incorrect udp data 2"; |
assert mac_tx_tlast = '0' report "T5: tlast asserted too soon"; wait for clk_period; |
assert mac_tx_tdata = x"53" report "T5: incorrect udp data 3"; |
assert mac_tx_tlast = '1' report "T5: tlast not asserted"; wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENT report "T5: TX did not complete"; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T5: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T5: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T5: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T5: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T5: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"04" report "T5: ip pkt cnt incorrect"; |
|
|
------------ |
-- TEST 6 -- send UDP pkt with data to trigger the sending of a pkt to unknown IP addr to force an ARP timeout |
------------ |
|
report "T6: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694 with data x43 to trig tx to unknown IP"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"43"; wait for clk_period; -- First byte 'C' triggers a reply to unknown addr |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T6: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T6: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T6: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T6: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T6: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T6: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T6: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T6: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T6: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T6: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T6: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T6: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T6: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
report "T6: waiting for mac data tx"; |
wait until mac_tx_tvalid = '1'; |
report "T6: starting mac data tx"; |
wait for clk_period; |
|
-- check the mac data being transmitted is valid ARP request |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T6: incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T6: incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T6: incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T6: incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T6: incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T6: incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T6: incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"06" report "T6: incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T6: incorrect HW type.0"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T6: incorrect HW type.1"; wait for clk_period; |
assert mac_tx_tdata = x"08" report "T6: incorrect prot.0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect prot.1"; wait for clk_period; |
assert mac_tx_tdata = x"06" report "T6: incorrect HW size"; wait for clk_period; |
assert mac_tx_tdata = x"04" report "T6: incorrect prot size"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect opcode.0"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T6: incorrect opcode.1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T6: incorrect sndr mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T6: incorrect sndr mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T6: incorrect sndr mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T6: incorrect sndr mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T6: incorrect sndr mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T6: incorrect sndr mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T6: incorrect sndr ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T6: incorrect sndr ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T6: incorrect sndr ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T6: incorrect sndr ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T6: incorrect trg ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"bb" report "T6: incorrect trg ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"cc" report "T6: incorrect trg ip 2"; |
assert mac_tx_tlast = '0' report "T6: tlast asserted too soon"; |
wait for clk_period; |
|
assert mac_tx_tdata = x"dd" report "T6: incorrect trg ip 3"; |
assert mac_tx_tlast = '1' report "T6: tlast should be set"; |
wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENDING report "T6: TX should still be in sending phase"; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T6: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T6: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T6: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T6: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T6: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"05" report "T6: ip pkt cnt incorrect"; |
|
-- check for error on tx as a result of ARP timeout |
|
wait for clk_period*10*20; |
assert udp_tx_result = IPTX_RESULT_ERR report "T6: TX should resulkt in error (arp timeout)"; |
|
wait for clk_period*10; |
|
------------ |
-- TEST 7 -- send UDP pkt again to ensure that we can rx a pkt and tx after a timeout |
------------ |
|
report "T7: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"68"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T7: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T7: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T7: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T7: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T7: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T7: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T7: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T7: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T7: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T7: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T7: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T7: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T7: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period*2; |
|
-- the mac address will be cached, so udp tx should occur straight away |
assert udp_tx_result = IPTX_RESULT_SENDING report "T7: TX should be sending"; |
|
report "T7: waiting for mac data tx"; |
if mac_tx_tvalid = '0' then |
wait until mac_tx_tvalid = '1'; |
wait for clk_period; |
end if; |
report "T7: starting mac data tx"; |
|
-- check the mac data being transmitted |
assert mac_tx_tdata = x"00" report "T7: incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"18" report "T7: incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"29" report "T7: incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"26" report "T7: incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"7c" report "T7: incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T7: incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T7: incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T7: incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T7: incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"45" report "T7: incorrect ver.hlen"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect srv type"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect len 0"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T7: incorrect len 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: incorrect ident 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect ident 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect flag&frag 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect flag&frag 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"80" report "T7: incorrect TTL"; wait for clk_period; |
assert mac_tx_tdata = x"11" report "T7: incorrect protocol"; wait for clk_period; |
assert mac_tx_tdata = x"af" report "T7: incorrect hdr.cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"72" report "T7: incorrect hdr.cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T7: incorrect src ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T7: incorrect src ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T7: incorrect src ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T7: incorrect src ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T7: incorrect dst ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T7: incorrect dst ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T7: incorrect dst ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T7: incorrect dst ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"26" report "T7: incorrect src port 0"; wait for clk_period; |
assert mac_tx_tdata = x"94" report "T7: incorrect src port 1"; wait for clk_period; |
assert mac_tx_tdata = x"f4" report "T7: incorrect dst port 0"; wait for clk_period; |
assert mac_tx_tdata = x"9a" report "T7: incorrect dst port 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: incorrect udp len 0"; wait for clk_period; |
assert mac_tx_tdata = x"0c" report "T7: incorrect udp len 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect udp cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect udp cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"40" report "T7: incorrect udp data 0"; wait for clk_period; |
assert mac_tx_tdata = x"41" report "T7: incorrect udp data 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"42" report "T7: incorrect udp data 2"; |
assert mac_tx_tlast = '0' report "T7: tlast asserted too soon"; wait for clk_period; |
assert mac_tx_tdata = x"43" report "T7: incorrect udp data 3"; |
assert mac_tx_tlast = '1' report "T7: tlast not asserted"; wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENT report "T7: TX did not complete"; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T7: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T7: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T7: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T7: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T7: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"06" report "T7: ip pkt cnt incorrect"; |
|
|
|
report "--- end of tests ---"; |
wait; |
end process; |
|
-- AUTO TX process - on receipt of any UDP pkt, send a response. data sent is modified if a broadcast was received. |
|
-- TX response process - COMB |
tx_proc_combinatorial: process( |
-- inputs |
udp_rx_start_int, udp_rx_int, udp_tx_data_out_ready_int, udp_tx_result, ip_rx_hdr, |
udp_tx_int.data.data_out_valid, PBTX, |
-- state |
state, count, tx_hdr, tx_start_reg, tx_started_reg, tx_fin_reg, |
-- controls |
next_state, set_state, set_count, set_hdr, set_tx_start, set_last, |
set_tx_started, set_tx_fin, first_byte_rx |
) |
begin |
-- set output_followers |
udp_tx_int.hdr <= tx_hdr; |
udp_tx_int.data.data_out_last <= set_last; |
udp_tx_start_int <= tx_start_reg; |
|
-- set control signal defaults |
next_state <= IDLE; |
set_state <= '0'; |
set_count <= HOLD; |
set_hdr <= '0'; |
set_tx_start <= HOLD; |
set_last <= '0'; |
set_tx_started <= HOLD; |
set_tx_fin <= HOLD; |
first_byte_rx <= (others => '0'); |
|
-- FSM |
case state is |
|
when IDLE => |
udp_tx_int.data.data_out <= (others => '0'); |
udp_tx_int.data.data_out_valid <= '0'; |
if udp_rx_start_int = '1' or PBTX = '1' then |
if udp_rx_start_int = '1' then |
first_byte_rx <= udp_rx_int.data.data_in; |
else |
first_byte_rx <= x"00"; |
end if; |
set_tx_fin <= CLR; |
set_count <= RST; |
set_hdr <= '1'; |
if udp_rx_int.data.data_in_last = '1' then |
set_tx_started <= SET; |
set_tx_start <= SET; |
next_state <= DATA_OUT; |
set_state <= '1'; |
else |
next_state <= WAIT_RX_DONE; |
set_state <= '1'; |
end if; |
end if; |
|
when WAIT_RX_DONE => |
-- wait until RX pkt fully received |
if udp_rx_int.data.data_in_last = '1' then |
set_tx_started <= SET; |
set_tx_start <= SET; |
next_state <= DATA_OUT; |
set_state <= '1'; |
end if; |
|
when DATA_OUT => |
if udp_tx_result = UDPTX_RESULT_ERR then |
-- have an error from the IP TX layer, clear down the TX |
set_tx_start <= CLR; |
set_tx_fin <= SET; |
set_tx_started <= CLR; |
next_state <= IDLE; |
set_state <= '1'; |
else |
if udp_tx_result = UDPTX_RESULT_SENDING then |
set_tx_start <= CLR; -- reset out start req as soon as we know we are sending |
end if; |
if ip_rx_hdr.is_broadcast = '1' then |
udp_tx_int.data.data_out <= std_logic_vector(count) or x"50"; |
else |
udp_tx_int.data.data_out <= std_logic_vector(count) or x"40"; |
end if; |
udp_tx_int.data.data_out_valid <= udp_tx_data_out_ready_int; |
if udp_tx_data_out_ready_int = '1' then |
if unsigned(count) = x"03" then |
set_last <= '1'; |
set_tx_fin <= SET; |
set_tx_started <= CLR; |
next_state <= IDLE; |
set_state <= '1'; |
else |
set_count <= INCR; |
end if; |
end if; |
end if; |
|
end case; |
end process; |
|
|
|
-- TX response process - SEQ |
tx_proc_sequential: process(clk_int) |
begin |
if rising_edge(clk_int) then |
if reset = '1' then |
-- reset state variables |
state <= IDLE; |
count <= x"00"; |
tx_start_reg <= '0'; |
tx_hdr.dst_ip_addr <= (others => '0'); |
tx_hdr.dst_port <= (others => '0'); |
tx_hdr.src_port <= (others => '0'); |
tx_hdr.data_length <= (others => '0'); |
tx_hdr.checksum <= (others => '0'); |
tx_started_reg <= '0'; |
tx_fin_reg <= '0'; |
PBTX_LED <= '0'; |
else |
PBTX_LED <= PBTX; |
|
-- Next rx_state processing |
if set_state = '1' then |
state <= next_state; |
else |
state <= state; |
end if; |
|
-- count processing |
case set_count is |
when RST => count <= x"00"; |
when INCR => count <= count + 1; |
when HOLD => count <= count; |
end case; |
|
-- set tx hdr |
if set_hdr = '1' then |
-- if the first byte of the rx pkt is 'B' then send to broadcast, otherwise send to reply IP |
if first_byte_rx = x"42" then |
tx_hdr.dst_ip_addr <= IP_BC_ADDR; -- send to Broadcast addr |
elsif first_byte_rx = x"43" then |
tx_hdr.dst_ip_addr <= x"c0bbccdd"; -- set dst unknown so get ARP timeout |
else |
tx_hdr.dst_ip_addr <= udp_rx_int.hdr.src_ip_addr; -- reply to sender |
end if; |
tx_hdr.dst_port <= udp_rx_int.hdr.src_port; |
tx_hdr.src_port <= udp_rx_int.hdr.dst_port; |
tx_hdr.data_length <= x"0004"; |
tx_hdr.checksum <= x"0000"; |
else |
tx_hdr <= tx_hdr; |
end if; |
|
-- set tx start signal |
case set_tx_start is |
when SET => tx_start_reg <= '1'; |
when CLR => tx_start_reg <= '0'; |
when HOLD => tx_start_reg <= tx_start_reg; |
end case; |
|
-- set tx started signal |
case set_tx_started is |
when SET => tx_started_reg <= '1'; |
when CLR => tx_started_reg <= '0'; |
when HOLD => tx_started_reg <= tx_started_reg; |
end case; |
|
-- set tx finished signal |
case set_tx_fin is |
when SET => tx_fin_reg <= '1'; |
when CLR => tx_fin_reg <= '0'; |
when HOLD => tx_fin_reg <= tx_fin_reg; |
end case; |
|
|
end if; |
end if; |
|
end process; |
|
END; |
/arpv2_tb.vhd
0,0 → 1,956
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 12:35:50 05/31/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/arp1/arp_tb.vhd |
-- Project Name: arp1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: arp |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Revision 0.02 - Added tests for ARP timeout |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
LIBRARY ieee; |
USE ieee.std_logic_1164.ALL; |
USE ieee.numeric_std.ALL; |
use work.arp_types.all; |
|
ENTITY arpv2_tb IS |
END arpv2_tb; |
|
ARCHITECTURE behavior OF arpv2_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT arpv2 |
generic ( |
CLOCK_FREQ : integer := 125000000; -- freq of data_in_clk -- needed to timout cntr |
ARP_TIMEOUT : integer := 60; -- ARP response timeout (s) |
MAX_ARP_ENTRIES : integer := 255 -- max entries in the arp store |
); |
Port ( |
-- lookup request signals |
arp_req_req : in arp_req_req_type; |
arp_req_rslt : out arp_req_rslt_type; |
-- MAC layer RX signals |
data_in_clk : in STD_LOGIC; |
reset : in STD_LOGIC; |
data_in : in STD_LOGIC_VECTOR (7 downto 0); -- ethernet frame (from dst mac addr through to last byte of frame) |
data_in_valid : in STD_LOGIC; -- indicates data_in valid on clock |
data_in_last : in STD_LOGIC; -- indicates last data in frame |
-- MAC layer TX signals |
mac_tx_req : out std_logic; -- indicates that ip wants access to channel (stays up for as long as tx) |
mac_tx_granted : in std_logic; -- indicates that access to channel has been granted |
data_out_clk : in std_logic; |
data_out_ready : in std_logic; -- indicates system ready to consume data |
data_out_valid : out std_logic; -- indicates data out is valid |
data_out_first : out std_logic; -- with data out valid indicates the first byte of a frame |
data_out_last : out std_logic; -- with data out valid indicates the last byte of a frame |
data_out : out std_logic_vector (7 downto 0); -- ethernet frame (from dst mac addr through to last byte of frame) |
-- system signals |
our_mac_address : in STD_LOGIC_VECTOR (47 downto 0); |
our_ip_address : in STD_LOGIC_VECTOR (31 downto 0); |
control : in arp_control_type; |
req_count : out STD_LOGIC_VECTOR(7 downto 0) -- count of arp pkts received |
); |
END COMPONENT; |
|
|
--Inputs |
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal data_in : std_logic_vector(7 downto 0) := (others => '0'); |
signal data_in_valid : std_logic := '0'; |
signal data_in_last : std_logic := '0'; |
signal our_mac_address : std_logic_vector(47 downto 0) := (others => '0'); |
signal our_ip_address : std_logic_vector(31 downto 0) := (others => '0'); |
signal data_out_ready : std_logic; |
signal data_out_valid : std_logic; |
signal data_out_first : std_logic; |
signal data_out_last : std_logic; |
signal data_out : std_logic_vector (7 downto 0); |
signal req_count : STD_LOGIC_VECTOR(7 downto 0); |
signal arp_req_req : arp_req_req_type; |
signal arp_req_rslt : arp_req_rslt_type; |
signal mac_tx_req : std_logic; |
signal mac_tx_granted : std_logic; |
signal control : arp_control_type; |
|
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: arpv2 |
generic map ( |
CLOCK_FREQ => 10, -- artificially low count to enable pragmatic testing |
ARP_TIMEOUT => 20 |
) |
PORT MAP ( |
-- lookup request mappings |
arp_req_req => arp_req_req, |
arp_req_rslt => arp_req_rslt, |
-- rx mappings |
data_in_clk => clk, |
reset => reset, |
data_in => data_in, |
data_in_valid => data_in_valid, |
data_in_last => data_in_last, |
-- tx mappings |
mac_tx_req => mac_tx_req, |
mac_tx_granted => mac_tx_granted, |
data_out_clk => clk, |
data_out_ready => data_out_ready, |
data_out_valid => data_out_valid, |
data_out_first => data_out_first, |
data_out_last => data_out_last, |
data_out => data_out, |
-- system mappings |
our_mac_address => our_mac_address, |
our_ip_address => our_ip_address, |
control => control, |
req_count => req_count |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '0'; |
wait for clk_period/2; |
clk <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 100 ns; |
|
our_ip_address <= x"c0a80509"; -- 192.168.5.9 |
our_mac_address <= x"002320212223"; |
mac_tx_granted <= '1'; -- FIXME 0 |
control.clear_cache <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
assert mac_tx_req = '0' report "mac_tx_req asserted on reset"; |
|
-- insert stimulus here |
arp_req_req.lookup_req <= '0'; |
arp_req_req.ip <= (others => '0'); |
data_out_ready <= '1'; |
|
report "T1: Send an ARP request: who has 192.168.5.9? Tell 192.168.5.1"; |
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"18"; wait for clk_period; |
data_in <= x"29"; wait for clk_period; |
data_in <= x"26"; wait for clk_period; |
data_in <= x"7c"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Sender MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"18"; wait for clk_period; |
data_in <= x"29"; wait for clk_period; |
data_in <= x"26"; wait for clk_period; |
data_in <= x"7c"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
|
report "T1: Expect that we send an 'I have 192.168.5.9' msg"; |
|
-- check tx arbitration signals |
|
report "T1: waiting for tx req"; |
wait until mac_tx_req = '1'; |
|
-- ready to tx |
data_out_ready <= '1'; |
mac_tx_granted <= '1'; |
report "T1: waiting for data_out_valid"; |
wait until data_out_valid = '1'; |
report "T1: got data_out_valid"; |
wait for clk_period*10; |
data_out_ready <= '0'; |
wait for clk_period*2; |
data_out_ready <= '1'; |
wait for clk_period*12; |
assert data_out = x"02" report "T1: expected opcode = 02 for reply 'I have'"; |
-- expect our mac 00 23 20 21 22 23 |
wait for clk_period; |
assert data_out = x"00" report "T1: incorrect our mac.0"; |
wait for clk_period; |
assert data_out = x"23" report "T1: incorrect our mac.1"; |
wait for clk_period; |
assert data_out = x"20" report "T1: incorrect our mac.2"; |
wait for clk_period; |
assert data_out = x"21" report "T1: incorrect our mac.3"; |
wait for clk_period; |
assert data_out = x"22" report "T1: incorrect our mac.4"; |
wait for clk_period; |
assert data_out = x"23" report "T1: incorrect our mac.5"; |
-- expect our IP c0 a8 05 05 |
wait for clk_period; |
assert data_out = x"c0" report "T1: incorrect our IP.0"; |
wait for clk_period; |
assert data_out = x"a8" report "T1: incorrect our IP.1"; |
wait for clk_period; |
assert data_out = x"05" report "T1: incorrect our IP.2"; |
wait for clk_period; |
assert data_out = x"09" report "T1: incorrect our IP.3"; |
|
-- expect target mac 00 23 18 29 26 7c |
wait for clk_period; |
assert data_out = x"00" report "T1: incorrect target mac.0"; |
wait for clk_period; |
assert data_out = x"23" report "T1: incorrect target mac.1"; |
wait for clk_period; |
assert data_out = x"18" report "T1: incorrect target mac.2"; |
wait for clk_period; |
assert data_out = x"29" report "T1: incorrect target mac.3"; |
wait for clk_period; |
assert data_out = x"26" report "T1: incorrect target mac.4"; |
wait for clk_period; |
assert data_out = x"7c" report "T1: incorrect target mac.5"; |
-- expect target IP c0 a8 05 01 |
wait for clk_period; |
assert data_out = x"c0" report "T1: incorrect target IP.0"; |
wait for clk_period; |
assert data_out = x"a8" report "T1: incorrect target IP.1"; |
wait for clk_period; |
assert data_out = x"05" report "T1: incorrect target IP.2"; |
assert data_out_last = '0' report "T1: data out last incorrectly set on target IP.2 byte"; |
wait for clk_period; |
assert data_out = x"01" report "T1: incorrect target IP.3"; |
assert data_out_last = '1' report "T1: data out last should be set"; |
|
wait for clk_period*10; |
|
report "T2: Send another ARP request: who has 192.168.5.8? Tell 192.168.5.1, holding off transmitter"; |
data_out_ready <= '0'; |
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"18"; wait for clk_period; |
data_in <= x"29"; wait for clk_period; |
data_in <= x"26"; wait for clk_period; |
data_in <= x"7c"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Sender MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"18"; wait for clk_period; |
data_in <= x"29"; wait for clk_period; |
data_in <= x"26"; wait for clk_period; |
data_in <= x"7c"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
|
-- ready to tx |
wait for clk_period*10; |
data_out_ready <= '1'; |
|
wait for clk_period*50; |
|
report "T3: Send a request for the IP that is already in the store"; |
arp_req_req.ip <= x"c0a80501"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
report "T3: wait for reply from store"; |
wait until arp_req_rslt.got_mac = '1' or arp_req_rslt.got_err = '1'; |
assert arp_req_rslt.got_mac = '1' report "T3: expected got mac"; |
assert arp_req_rslt.got_err = '0' report "T3: expected got err = 0"; |
assert arp_req_rslt.mac = x"00231829267c" report "T3: wrong mac value"; |
wait for clk_period*2; |
|
-- the entry that was in the store should now be in the cache - check it |
report "T4: Send a request for the IP that is already in the cache"; |
arp_req_req.ip <= x"c0a80501"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
assert arp_req_rslt.got_mac = '1' report "T4: expected got mac"; |
assert arp_req_rslt.got_err = '0' report "T4: expected got err = 0"; |
assert arp_req_rslt.mac = x"00231829267c" report "T4: wrong mac value"; |
|
wait for clk_period*50; |
|
report "T5 - Send a request for the IP that is not cached or in the store"; |
arp_req_req.ip <= x"c0a80503"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
report "T5: waiting for data_out_valid"; |
wait until data_out_valid = '1'; |
report "T5: got data_out_valid"; |
wait for clk_period*10; |
data_out_ready <= '0'; |
wait for clk_period*2; |
data_out_ready <= '1'; |
wait for clk_period*12; |
assert data_out = x"01" report "T5: expected opcode = 01 for request 'who has'"; |
-- expect our mac 00 23 20 21 22 23 |
wait for clk_period; |
assert data_out = x"00" report "T5: incorrect our mac.0"; |
wait for clk_period; |
assert data_out = x"23" report "T5: incorrect our mac.1"; |
wait for clk_period; |
assert data_out = x"20" report "T5: incorrect our mac.2"; |
wait for clk_period; |
assert data_out = x"21" report "T5: incorrect our mac.3"; |
wait for clk_period; |
assert data_out = x"22" report "T5: incorrect our mac.4"; |
wait for clk_period; |
assert data_out = x"23" report "T5: incorrect our mac.5"; |
-- expect our IP c0 a8 05 05 |
wait for clk_period; |
assert data_out = x"c0" report "T5: incorrect our IP.0"; |
wait for clk_period; |
assert data_out = x"a8" report "T5: incorrect our IP.1"; |
wait for clk_period; |
assert data_out = x"05" report "T5: incorrect our IP.2"; |
wait for clk_period; |
assert data_out = x"09" report "T5: incorrect our IP.3"; |
|
-- expect empty target mac |
wait for clk_period; |
assert data_out = x"00" report "T5: incorrect target mac.0"; |
wait for clk_period; |
assert data_out = x"00" report "T5: incorrect target mac.1"; |
wait for clk_period; |
assert data_out = x"00" report "T5: incorrect target mac.2"; |
wait for clk_period; |
assert data_out = x"00" report "T5: incorrect target mac.3"; |
wait for clk_period; |
assert data_out = x"00" report "T5: incorrect target mac.4"; |
wait for clk_period; |
assert data_out = x"00" report "T5: incorrect target mac.5"; |
-- expect target IP c0 a8 05 01 |
wait for clk_period; |
assert data_out = x"c0" report "T5: incorrect target IP.0"; |
wait for clk_period; |
assert data_out = x"a8" report "T5: incorrect target IP.1"; |
wait for clk_period; |
assert data_out = x"05" report "T5: incorrect target IP.2"; |
assert data_out_last = '0' report "T5: data out last incorrectly set on target IP.2 byte"; |
wait for clk_period; |
assert data_out = x"03" report "T5: incorrect target IP.3"; |
assert data_out_last = '1' report "T5: data out last should be set"; |
|
wait for clk_period*10; |
|
-- Send the reply |
data_out_ready <= '1'; |
|
report "T5.2: Send an ARP reply: 192.168.5.3 has mac 02:12:03:23:04:54"; |
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"12"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"02"; wait for clk_period; |
-- Sender MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"12"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"20"; wait for clk_period; |
data_in <= x"21"; wait for clk_period; |
data_in <= x"22"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T5.2: expected got mac"; |
assert arp_req_rslt.got_err = '0' report "T5.2: expected got err = 0"; |
assert arp_req_rslt.mac = x"021203230454" report "T5.2: wrong mac value"; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
wait for clk_period*4; |
|
report "T6: check that both these IPs remain in the store"; |
arp_req_req.ip <= x"c0a80501"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
wait for clk_period; |
report "T6.1: wait for reply from store"; |
wait until arp_req_rslt.got_mac = '1' or arp_req_rslt.got_err = '1'; |
assert arp_req_rslt.got_mac = '1' report "T6.1: expected got mac"; |
assert arp_req_rslt.got_err = '0' report "T6.1: expected got err = 0"; |
assert arp_req_rslt.mac = x"00231829267c" report "T6.1: wrong mac value"; |
wait for clk_period*2; |
|
arp_req_req.ip <= x"c0a80503"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
wait for clk_period; |
report "T6.2: wait for reply from store"; |
wait until arp_req_rslt.got_mac = '1' or arp_req_rslt.got_err = '1'; |
assert arp_req_rslt.got_mac = '1' report "T6.2: expected got mac"; |
assert arp_req_rslt.got_err = '0' report "T6.2: expected got err = 0"; |
assert arp_req_rslt.mac = x"021203230454" report "T6.2: wrong mac value"; |
wait for clk_period*2; |
|
report "T7 - test that receipt of wrong I Have does not satisfy a current req"; |
arp_req_req.ip <= x"c0a8050e"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
report "T7: waiting for data_out_valid"; |
wait until data_out_valid = '1'; |
report "T7: got data_out_valid"; |
wait for clk_period*10; |
data_out_ready <= '0'; |
wait for clk_period*2; |
data_out_ready <= '1'; |
wait for clk_period*12; |
assert data_out = x"01" report "T7: expected opcode = 01 for request 'who has'"; |
-- expect our mac 00 23 20 21 22 23 |
wait for clk_period; |
assert data_out = x"00" report "T7: incorrect our mac.0"; |
wait for clk_period; |
assert data_out = x"23" report "T7: incorrect our mac.1"; |
wait for clk_period; |
assert data_out = x"20" report "T7: incorrect our mac.2"; |
wait for clk_period; |
assert data_out = x"21" report "T7: incorrect our mac.3"; |
wait for clk_period; |
assert data_out = x"22" report "T7: incorrect our mac.4"; |
wait for clk_period; |
assert data_out = x"23" report "T7: incorrect our mac.5"; |
-- expect our IP c0 a8 05 05 |
wait for clk_period; |
assert data_out = x"c0" report "T7: incorrect our IP.0"; |
wait for clk_period; |
assert data_out = x"a8" report "T7: incorrect our IP.1"; |
wait for clk_period; |
assert data_out = x"05" report "T7: incorrect our IP.2"; |
wait for clk_period; |
assert data_out = x"09" report "T7: incorrect our IP.3"; |
|
-- expect empty target mac |
wait for clk_period; |
assert data_out = x"00" report "T7: incorrect target mac.0"; |
wait for clk_period; |
assert data_out = x"00" report "T7: incorrect target mac.1"; |
wait for clk_period; |
assert data_out = x"00" report "T7: incorrect target mac.2"; |
wait for clk_period; |
assert data_out = x"00" report "T7: incorrect target mac.3"; |
wait for clk_period; |
assert data_out = x"00" report "T7: incorrect target mac.4"; |
wait for clk_period; |
assert data_out = x"00" report "T7: incorrect target mac.5"; |
-- expect target IP c0 a8 05 0e |
wait for clk_period; |
assert data_out = x"c0" report "T7: incorrect target IP.0"; |
wait for clk_period; |
assert data_out = x"a8" report "T7: incorrect target IP.1"; |
wait for clk_period; |
assert data_out = x"05" report "T7: incorrect target IP.2"; |
assert data_out_last = '0' report "T7: data out last incorrectly set on target IP.2 byte"; |
wait for clk_period; |
assert data_out = x"0e" report "T7: incorrect target IP.3"; |
assert data_out_last = '1' report "T7: data out last should be set"; |
|
wait for clk_period*10; |
|
-- Send the reply |
data_out_ready <= '1'; |
|
report "T7.2: Send an arbitrary unwanted ARP reply: 192.168.7.3 has mac 57:12:34:19:23:9a"; |
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"57"; wait for clk_period; |
data_in <= x"12"; wait for clk_period; |
data_in <= x"34"; wait for clk_period; |
data_in <= x"19"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"9a"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"02"; wait for clk_period; |
-- Sender MAC |
data_in <= x"57"; wait for clk_period; |
data_in <= x"12"; wait for clk_period; |
data_in <= x"34"; wait for clk_period; |
data_in <= x"19"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"9a"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"07"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"20"; wait for clk_period; |
data_in <= x"21"; wait for clk_period; |
data_in <= x"22"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
assert arp_req_rslt.got_mac = '0' report "T7.2: expected got mac = 0"; |
assert arp_req_rslt.got_err = '0' report "T7.2: expected got err = 0"; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
wait for clk_period*4; |
|
-- Send the reply |
data_out_ready <= '1'; |
|
report "T7.3: Send a wanted ARP reply: 192.168.5.e has mac 76:34:98:55:aa:37"; |
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"76"; wait for clk_period; |
data_in <= x"34"; wait for clk_period; |
data_in <= x"98"; wait for clk_period; |
data_in <= x"55"; wait for clk_period; |
data_in <= x"aa"; wait for clk_period; |
data_in <= x"37"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"02"; wait for clk_period; |
-- Sender MAC |
data_in <= x"76"; wait for clk_period; |
data_in <= x"34"; wait for clk_period; |
data_in <= x"98"; wait for clk_period; |
data_in <= x"55"; wait for clk_period; |
data_in <= x"aa"; wait for clk_period; |
data_in <= x"37"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"0e"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"20"; wait for clk_period; |
data_in <= x"21"; wait for clk_period; |
data_in <= x"22"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T7.3: expected got mac"; |
assert arp_req_rslt.got_err = '0' report "T7.3: expected got err = 0"; |
assert arp_req_rslt.mac = x"76349855aa37" report "T7.3: wrong mac value"; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
wait for clk_period*4; |
|
|
report "T8: Request 192.168.5.4 (not cached), dont send a reply and wait for timeout"; |
arp_req_req.ip <= x"c0a80504"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
assert mac_tx_req = '1' report "T8: should be requesting TX channel"; |
wait for clk_period*220; |
assert arp_req_rslt.got_mac = '0' report "T8: should not have got mac"; |
assert arp_req_rslt.got_err = '1' report "T8: should have got err"; |
|
report "T9: Request 192.168.5.7 (not cached= and Send an ARP reply: 192.168.5.7 has mac 02:15:03:23:04:54"; |
arp_req_req.ip <= x"c0a80507"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '0' report "T9: should not yet have mac"; |
assert arp_req_rslt.got_err = '0' report "T9: should not have got err"; |
|
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
assert mac_tx_req = '1' report "T9: should be requesting TX channel"; |
wait for clk_period*50; |
-- Send the reply |
data_out_ready <= '1'; |
|
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"15"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"02"; wait for clk_period; |
-- Sender MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"15"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"07"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"20"; wait for clk_period; |
data_in <= x"21"; wait for clk_period; |
data_in <= x"22"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T9: should have got mac"; |
assert arp_req_rslt.mac = x"021503230454" report "T9: incorrect mac"; |
assert arp_req_rslt.got_err = '0' report "T9: should not have got err"; |
wait for clk_period*10; |
|
report "T10: Request 192.168.5.7 again an expect it to be in the cache"; |
arp_req_req.ip <= x"c0a80507"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T10: should have mac"; |
assert arp_req_rslt.got_err = '0' report "T10: should not have got err"; |
|
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
|
report "T11: Clear the cache, Request 192.168.5.7 again an expect a 'who has' to be sent"; |
control.clear_cache <= '1'; |
wait for clk_period; |
control.clear_cache <= '0'; |
wait for clk_period; |
|
arp_req_req.ip <= x"c0a80507"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '0' report "T11: should not yet have mac"; |
assert arp_req_rslt.got_err = '0' report "T11: should not have got err"; |
|
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
|
|
assert mac_tx_req = '1' report "T11: should be requesting TX channel"; |
wait for clk_period*50; |
-- Send the reply |
data_out_ready <= '1'; |
|
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"15"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"02"; wait for clk_period; |
-- Sender MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"15"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"55"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"07"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"20"; wait for clk_period; |
data_in <= x"21"; wait for clk_period; |
data_in <= x"22"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T11: should have got mac"; |
assert arp_req_rslt.mac = x"021503235554" report "T11: incorrect mac"; |
assert arp_req_rslt.got_err = '0' report "T11: should not have got err"; |
wait for clk_period*10; |
|
report "--- end of tests ---"; |
wait; |
end process; |
|
END; |
/IP_complete_nomac_tb.vhd
0,0 → 1,438
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 13:54:32 06/04/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/ip1/IP_complete_nomac_tb.vhd |
-- Project Name: ip1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: IP_complete_nomac |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
LIBRARY ieee; |
USE ieee.std_logic_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use work.axi.all; |
use work.ipv4_types.all; |
use work.arp_types.all; |
|
ENTITY IP_complete_nomac_tb IS |
END IP_complete_nomac_tb; |
|
ARCHITECTURE behavior OF IP_complete_nomac_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT IP_complete_nomac |
generic ( |
CLOCK_FREQ : integer := 125000000; -- freq of data_in_clk -- needed to timout cntr |
ARP_TIMEOUT : integer := 60 -- ARP response timeout (s) |
); |
Port ( |
-- IP Layer signals |
ip_tx_start : in std_logic; |
ip_tx : in ipv4_tx_type; -- IP tx cxns |
ip_tx_result : out std_logic_vector (1 downto 0); -- tx status (changes during transmission) |
ip_tx_data_out_ready : out std_logic; -- indicates IP TX is ready to take data |
ip_rx_start : out std_logic; -- indicates receipt of ip frame. |
ip_rx : out ipv4_rx_type; |
-- system signals |
rx_clk : in STD_LOGIC; |
tx_clk : in STD_LOGIC; |
reset : in STD_LOGIC; |
our_ip_address : in STD_LOGIC_VECTOR (31 downto 0); |
our_mac_address : in std_logic_vector (47 downto 0); |
control : in ip_control_type; |
-- status signals |
arp_pkt_count : out STD_LOGIC_VECTOR(7 downto 0); -- count of arp pkts received |
ip_pkt_count : out STD_LOGIC_VECTOR(7 downto 0); -- number of IP pkts received for us |
-- MAC Transmitter |
mac_tx_tdata : out std_logic_vector(7 downto 0); -- data byte to tx |
mac_tx_tvalid : out std_logic; -- tdata is valid |
mac_tx_tready : in std_logic; -- mac is ready to accept data |
mac_tx_tfirst : out std_logic; -- indicates first byte of frame |
mac_tx_tlast : out std_logic; -- indicates last byte of frame |
-- MAC Receiver |
mac_rx_tdata : in std_logic_vector(7 downto 0); -- data byte received |
mac_rx_tvalid : in std_logic; -- indicates tdata is valid |
mac_rx_tready : out std_logic; -- tells mac that we are ready to take data |
mac_rx_tlast : in std_logic -- indicates last byte of the trame |
); |
END COMPONENT; |
|
|
--Inputs |
signal ip_tx_start : std_logic := '0'; |
signal ip_tx : ipv4_tx_type; |
|
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal our_ip_address : std_logic_vector(31 downto 0) := (others => '0'); |
signal our_mac_address : std_logic_vector(47 downto 0) := (others => '0'); |
signal mac_tx_tready : std_logic := '0'; |
signal mac_rx_tdata : std_logic_vector(7 downto 0) := (others => '0'); |
signal mac_rx_tvalid : std_logic := '0'; |
signal mac_rx_tlast : std_logic := '0'; |
signal control : ip_control_type; |
|
--Outputs |
signal ip_tx_result : std_logic_vector (1 downto 0); -- tx status (changes during transmission) |
signal ip_tx_data_out_ready : std_logic; -- indicates IP TX is ready to take data |
signal ip_rx_start : std_logic; |
signal ip_rx : ipv4_rx_type; |
signal arp_pkt_count : std_logic_vector(7 downto 0); |
signal mac_tx_tdata : std_logic_vector(7 downto 0); |
signal mac_tx_tvalid : std_logic; |
signal mac_tx_tfirst : std_logic; |
signal mac_tx_tlast : std_logic; |
signal mac_rx_tready : std_logic; |
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: IP_complete_nomac PORT MAP ( |
ip_tx_start => ip_tx_start, |
ip_tx => ip_tx, |
ip_tx_result => ip_tx_result, |
ip_tx_data_out_ready => ip_tx_data_out_ready, |
ip_rx_start => ip_rx_start, |
ip_rx => ip_rx, |
rx_clk => clk, |
tx_clk => clk, |
reset => reset, |
our_ip_address => our_ip_address, |
our_mac_address => our_mac_address, |
control => control, |
arp_pkt_count => arp_pkt_count, |
mac_tx_tdata => mac_tx_tdata, |
mac_tx_tvalid => mac_tx_tvalid, |
mac_tx_tready => mac_tx_tready, |
mac_tx_tfirst => mac_tx_tfirst, |
mac_tx_tlast => mac_tx_tlast, |
mac_rx_tdata => mac_rx_tdata, |
mac_rx_tvalid => mac_rx_tvalid, |
mac_rx_tready => mac_rx_tready, |
mac_rx_tlast => mac_rx_tlast |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '1'; |
wait for clk_period/2; |
clk <= '0'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 80 ns; |
|
our_ip_address <= x"c0a80509"; -- 192.168.5.9 |
our_mac_address <= x"002320212223"; |
control.arp_controls.clear_cache <= '0'; |
ip_tx_start <= '0'; |
mac_tx_tready <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
-- check reset conditions |
assert ip_tx_result = IPTX_RESULT_NONE report "ip_tx_result not initialised correctly on reset"; |
assert ip_tx_data_out_ready = '0' report "ip_tx_data_out_ready not initialised correctly on reset"; |
assert mac_tx_tvalid = '0' report "mac_tx_tvalid not initialised correctly on reset"; |
assert mac_tx_tlast = '0' report " mac_tx_tlast not initialised correctly on reset"; |
assert arp_pkt_count = x"00" report " arp_pkt_count not initialised correctly on reset"; |
assert ip_rx_start = '0' report "ip_rx_start not initialised correctly on reset"; |
assert ip_rx.hdr.is_valid = '0' report "ip_rx.hdr.is_valid not initialised correctly on reset"; |
assert ip_rx.hdr.protocol = x"00" report "ip_rx.hdr.protocol not initialised correctly on reset"; |
assert ip_rx.hdr.data_length = x"0000" report "ip_rx.hdr.data_length not initialised correctly on reset"; |
assert ip_rx.hdr.src_ip_addr = x"00000000" report "ip_rx.hdr.src_ip_addr not initialised correctly on reset"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "ip_rx.hdr.num_frame_errors not initialised correctly on reset"; |
assert ip_rx.data.data_in = x"00" report "ip_rx.data.data_in not initialised correctly on reset"; |
assert ip_rx.data.data_in_valid = '0' report "ip_rx.data.data_in_valid not initialised correctly on reset"; |
assert ip_rx.data.data_in_last = '0' report "ip_rx.data.data_in_last not initialised correctly on reset"; |
|
-- insert stimulus here |
|
------------ |
-- TEST 1 -- basic functional rx test with received ip pkt |
------------ |
|
report "T1: Send an eth frame with IP pkt dst ip_address c0a80509, dst mac 002320212223"; |
|
mac_tx_tready <= '1'; |
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
|
-- user data |
mac_rx_tdata <= x"24"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert ip_rx.hdr.is_valid = '1' report "T1: ip_rx.hdr.is_valid not set"; |
assert ip_rx.hdr.protocol = x"11" report "T1: ip_rx.hdr.protocol not set correctly"; |
assert ip_rx.hdr.data_length = x"0004" report "T1: ip_rx.hdr.data_length not set correctly"; |
assert ip_rx.hdr.src_ip_addr = x"c0a80501" report "T1: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T1: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx.hdr.last_error_code = x"0" report "T1: ip_rx.hdr.last_error_code not set correctly"; |
assert ip_rx_start = '1' report "T1: ip_rx_start not set"; |
assert ip_rx.data.data_in_valid = '1' report "T1: ip_rx.data.data_in_valid not set"; |
|
mac_rx_tdata <= x"25"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"27"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert ip_rx.data.data_in_last = '1' report "T1: ip_rx.data.data_in_last not set"; |
|
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
assert ip_rx.data.data_in_valid = '0' report "T1: ip_rx.data.data_in_valid not cleared"; |
assert ip_rx.data.data_in_last = '0' report "T1: ip_rx.data.data_in_last not cleared"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T1: ip_rx.hdr.num_frame_errors non zero at end of test"; |
assert ip_rx.hdr.last_error_code = x"0" report "T1: ip_rx.hdr.last_error_code indicates error at end of test"; |
assert ip_rx_start = '0' report "T1: ip_rx_start not cleared"; |
|
------------ |
-- TEST 2 -- respond with IP TX |
------------ |
|
report "T2: respond with IP TX"; |
|
ip_tx.hdr.protocol <= x"35"; |
ip_tx.hdr.data_length <= x"0006"; |
ip_tx.hdr.dst_ip_addr <= x"c0123478"; |
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period; |
|
ip_tx_start <= '1'; wait for clk_period; |
|
ip_tx_start <= '0'; wait for clk_period; |
|
assert ip_tx_result = IPTX_RESULT_SENDING report "T2: result should be IPTX_RESULT_SENDING"; |
|
wait for clk_period*2; |
|
assert ip_tx_data_out_ready = '0' report "T2: IP data out ready asserted too early"; |
|
-- need to wait for ARP tx to complete |
|
wait for clk_period*50; |
|
assert mac_tx_tvalid = '0' report "T2: mac_tx_tvalid not cleared after ARP tx"; |
assert mac_tx_tlast = '0' report "T2: mac_tx_tlast not cleared after ARP tx"; |
|
-- now create the ARP response (rx) |
|
-- Send the reply |
-- Send an ARP reply: x"c0123478" has mac 02:12:03:23:04:54 |
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"02"; wait for clk_period; |
mac_rx_tdata <= x"12"; wait for clk_period; |
mac_rx_tdata <= x"03"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"04"; wait for clk_period; |
mac_rx_tdata <= x"54"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- HW type |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Protocol type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- HW size |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- protocol size |
mac_rx_tdata <= x"04"; wait for clk_period; |
-- Opcode |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"02"; wait for clk_period; |
-- Sender MAC |
mac_rx_tdata <= x"02"; wait for clk_period; |
mac_rx_tdata <= x"12"; wait for clk_period; |
mac_rx_tdata <= x"03"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"04"; wait for clk_period; |
mac_rx_tdata <= x"54"; wait for clk_period; |
-- Sender IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"12"; wait for clk_period; |
mac_rx_tdata <= x"34"; wait for clk_period; |
mac_rx_tdata <= x"78"; wait for clk_period; |
-- Target MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- Target IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '1'; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
|
wait until ip_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
ip_tx.data.data_out_valid <= '1'; |
ip_tx.data.data_out <= x"56"; wait for clk_period; |
ip_tx.data.data_out <= x"57"; wait for clk_period; |
ip_tx.data.data_out <= x"58"; wait for clk_period; |
ip_tx.data.data_out <= x"59"; wait for clk_period; |
ip_tx.data.data_out <= x"5a"; wait for clk_period; |
|
ip_tx.data.data_out <= x"5b"; |
ip_tx.data.data_out_last <= '1'; |
wait for clk_period; |
|
assert mac_tx_tlast = '1' report "T2: mac_tx_tlast not set on last byte"; |
|
wait for clk_period; |
|
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period*2; |
|
assert ip_tx_result = IPTX_RESULT_SENT report "T2: result should be SENT"; |
wait for clk_period*10; |
|
------------ |
-- TEST 3 -- Check that sending to the same IP addr doesnt cause an ARP req as the addr is cached |
------------ |
|
report "T3: Send 2nd IP TX to same IP addr - should not need to do ARP tx/rx"; |
ip_tx.hdr.protocol <= x"35"; |
ip_tx.hdr.data_length <= x"0006"; |
ip_tx.hdr.dst_ip_addr <= x"c0123478"; |
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period; |
ip_tx_start <= '1'; wait for clk_period; |
ip_tx_start <= '0'; wait for clk_period; |
assert ip_tx_result = IPTX_RESULT_SENDING report "T3: result should be IPTX_RESULT_SENDING"; |
wait for clk_period*2; |
assert ip_tx_data_out_ready = '0' report "T3: IP data out ready asserted too early"; |
wait until ip_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
ip_tx.data.data_out_valid <= '1'; |
ip_tx.data.data_out <= x"81"; wait for clk_period; |
ip_tx.data.data_out <= x"83"; wait for clk_period; |
ip_tx.data.data_out <= x"85"; wait for clk_period; |
ip_tx.data.data_out <= x"87"; wait for clk_period; |
ip_tx.data.data_out <= x"89"; wait for clk_period; |
|
ip_tx.data.data_out <= x"8b"; |
ip_tx.data.data_out_last <= '1'; |
wait for clk_period; |
|
assert mac_tx_tlast = '1' report "T3: mac_tx_tlast not set on last byte"; |
|
wait for clk_period; |
|
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period*2; |
|
assert ip_tx_result = IPTX_RESULT_SENT report "T3: result should be SENT"; |
wait for clk_period*2; |
|
|
|
report "-- end of tests --"; |
|
wait; |
end process; |
|
END; |
/arp_STORE_tb.vhd
0,0 → 1,384
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 07:38:43 02/13/2012 |
-- Design Name: |
-- Module Name: arp_STORE_tb.vhd |
-- Project Name: udp3 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: arp_STORE_br |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
library IEEE; |
use IEEE.STD_LOGIC_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use ieee.std_logic_unsigned.all; |
use work.arp_types.all; |
|
ENTITY arp_STORE_tb IS |
END arp_STORE_tb; |
|
ARCHITECTURE behavior OF arp_STORE_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT arp_STORE_br |
generic ( |
MAX_ARP_ENTRIES : integer := 256 -- max entries in the store |
); |
PORT( |
-- read signals |
read_req : in arp_store_rdrequest_t; -- requesting a '1' or store |
read_result : out arp_store_result_t; -- the result |
-- write signals |
write_req : in arp_store_wrrequest_t; -- requesting a '1' or store |
-- control and status signals |
clear_store : in std_logic; -- erase all entries |
entry_count : out unsigned(7 downto 0); -- how many entries currently in store |
-- system signals |
clk : in std_logic; |
reset : in STD_LOGIC |
); |
END COMPONENT; |
|
|
--Inputs |
signal read_req : arp_store_rdrequest_t; |
signal write_req : arp_store_wrrequest_t; |
signal clear_store : std_logic := '0'; |
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
|
--Outputs |
signal read_result : arp_store_result_t; |
signal entry_count : unsigned(7 downto 0); -- how many entries currently in store |
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: arp_STORE_br |
generic map ( |
MAX_ARP_ENTRIES => 4 |
) |
PORT MAP ( |
read_req => read_req, |
read_result => read_result, |
write_req => write_req, |
clear_store => clear_store, |
entry_count => entry_count, |
clk => clk, |
reset => reset |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '0'; |
wait for clk_period/2; |
clk <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
read_req.req <= '0'; |
read_req.ip <= (others => '0'); |
write_req.req <= '0'; |
write_req.entry.ip <= (others => '0'); |
write_req.entry.mac <= (others => '0'); |
reset <= '1'; |
-- hold reset state |
wait for clk_period*10; |
reset <= '0'; |
|
-- insert stimulus here |
report "T1 - look for something when store is empty"; |
read_req.ip <= x"12345678"; |
read_req.req <= '1'; |
wait for clk_period*4; |
assert read_result.status = NOT_FOUND report "T1: expected NOT_FOUND"; |
wait for clk_period; |
read_req.req <= '0'; |
wait for clk_period; |
assert read_result.status = IDLE report "T1: expected IDLE"; |
assert entry_count = x"00" report "T1: wrong entry count"; |
|
report "T2 - insert first entry into store"; |
write_req.entry.ip <= x"12345678"; |
write_req.entry.mac <= x"002398127645"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
assert entry_count = x"01" report "T2: wrong entry count"; |
|
report "T3 - check if can find this single entry"; |
read_req.ip <= x"12345678"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T3: expected FOUND"; |
assert read_result.entry.ip = x"12345678" report "T3: wrong ip addr"; |
assert read_result.entry.mac = x"002398127645" report "T3: wrong mac addr"; |
wait for clk_period; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T3: expected IDLE"; |
|
report "T4 - check unable to find missing entry with one entry in store"; |
read_req.ip <= x"12345679"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = NOT_FOUND report "T4: expected NOT_FOUND"; |
wait for clk_period; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T4: expected IDLE"; |
|
report "T5 - insert 2nd entry into store and check can find both entries"; |
write_req.entry.ip <= x"12345679"; |
write_req.entry.mac <= x"101202303404"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
assert entry_count = x"02" report "T4: wrong entry count"; |
read_req.ip <= x"12345678"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T5.1: expected FOUND"; |
assert read_result.entry.ip = x"12345678" report "T5.1: wrong ip addr"; |
assert read_result.entry.mac = x"002398127645" report "T5.1: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T5.1: expected IDLE"; |
read_req.ip <= x"12345679"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T5.2: expected FOUND"; |
assert read_result.entry.ip = x"12345679" report "T5.2: wrong ip addr"; |
assert read_result.entry.mac = x"101202303404" report "T5.2: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T5.2: expected IDLE"; |
|
report "T6 - insert 2 more entries so that the store is full. check can find all"; |
write_req.entry.ip <= x"1234567a"; |
write_req.entry.mac <= x"10120230340a"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
write_req.entry.ip <= x"1234567b"; |
write_req.entry.mac <= x"10120230340b"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
assert entry_count = x"04" report "T6: wrong entry count"; |
read_req.ip <= x"12345678"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T6.1: expected FOUND"; |
assert read_result.entry.ip = x"12345678" report "T6.1: wrong ip addr"; |
assert read_result.entry.mac = x"002398127645" report "T6.1: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T6.1: expected IDLE"; |
read_req.ip <= x"12345679"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T6.2: expected FOUND"; |
assert read_result.entry.ip = x"12345679" report "T6.2: wrong ip addr"; |
assert read_result.entry.mac = x"101202303404" report "T6.2: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T6.2: expected IDLE"; |
read_req.ip <= x"1234567a"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T6.3: expected FOUND"; |
assert read_result.entry.ip = x"1234567a" report "T6.3: wrong ip addr"; |
assert read_result.entry.mac = x"10120230340a" report "T6.3: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T6.3: expected IDLE"; |
read_req.ip <= x"1234567b"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T6.4: expected FOUND"; |
assert read_result.entry.ip = x"1234567b" report "T6.4: wrong ip addr"; |
assert read_result.entry.mac = x"10120230340b" report "T6.4: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T6.4: expected IDLE"; |
|
report "T7 - with store full, check that we dont find missing item"; |
read_req.ip <= x"1233367b"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = NOT_FOUND report "T7: expected NOT_FOUND"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T7: expected IDLE"; |
|
report "T8 - insert additional entry into store - will erase one of the others"; |
write_req.entry.ip <= x"12345699"; |
write_req.entry.mac <= x"992398127699"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
assert entry_count = x"04" report "T8: wrong entry count"; |
read_req.ip <= x"12345699"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T8: expected FOUND"; |
assert read_result.entry.ip = x"12345699" report "T8: wrong ip addr"; |
assert read_result.entry.mac = x"992398127699" report "T8: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T8: expected IDLE"; |
|
report "T9 - clear the store and ensure cant find something that was there"; |
clear_store <= '1'; |
wait for clk_period; |
clear_store <= '0'; |
wait for clk_period; |
assert entry_count = x"00" report "T9: wrong entry count"; |
read_req.ip <= x"12345699"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = NOT_FOUND report "T9: expected NOT_FOUND"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T9: expected IDLE"; |
|
report "T10 - refill the store with three entries"; |
write_req.entry.ip <= x"12345675"; |
write_req.entry.mac <= x"10120230340a"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
write_req.entry.ip <= x"12345676"; |
write_req.entry.mac <= x"10120230340b"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
write_req.entry.ip <= x"12345677"; |
write_req.entry.mac <= x"10120230340c"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
assert entry_count = x"03" report "T10: wrong entry count"; |
|
report "T11 - check middle entry, then change it and check again"; |
read_req.ip <= x"12345676"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T11.1: expected FOUND"; |
assert read_result.entry.ip = x"12345676" report "T11.1: wrong ip addr"; |
assert read_result.entry.mac = x"10120230340b" report "T11.1: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T11.1: expected IDLE"; |
write_req.entry.ip <= x"12345676"; |
write_req.entry.mac <= x"10120990340b"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait for clk_period; |
assert entry_count = x"03" report "T11: wrong entry count"; |
read_req.ip <= x"12345676"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T11.2: expected FOUND"; |
assert read_result.entry.ip = x"12345676" report "T11.2: wrong ip addr"; |
assert read_result.entry.mac = x"10120990340b" report "T11.2: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T11.2: expected IDLE"; |
|
report "T12 - check 2nd write at beginning"; |
-- clear store, write 1st entry, overwrite the entry, and check |
clear_store <= '1'; |
wait for clk_period; |
clear_store <= '0'; |
wait for clk_period; |
assert entry_count = x"00" report "T12.1: wrong entry count"; |
write_req.entry.ip <= x"12345678"; |
write_req.entry.mac <= x"002398127645"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
assert entry_count = x"01" report "T12.2: wrong entry count"; |
write_req.entry.ip <= x"12345678"; |
write_req.entry.mac <= x"002398127647"; |
write_req.req <= '1'; |
wait for clk_period; |
write_req.req <= '0'; |
wait until read_result.status = IDLE; |
wait for clk_period; |
assert entry_count = x"01" report "T12.3: wrong entry count"; |
read_req.ip <= x"12345678"; |
read_req.req <= '1'; |
wait until read_result.status = FOUND or read_result.status = NOT_FOUND; |
wait for clk_period; |
assert read_result.status = FOUND report "T12.4: expected FOUND"; |
assert read_result.entry.ip = x"12345678" report "T12.4: wrong ip addr"; |
assert read_result.entry.mac = x"002398127647" report "T12.4: wrong mac addr"; |
read_req.req <= '0'; |
wait for clk_period*2; |
assert read_result.status = IDLE report "T12.5: expected IDLE"; |
|
report "--- end of tests ---"; |
wait; |
end process; |
|
END; |
/IPv4_TX_tb.vhd
0,0 → 1,363
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 09:35:58 06/03/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/ip1/IPv4_TX_tb.vhd |
-- Project Name: ip1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: IPv4_TX |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Revision 0.02 - Added test for IP broadcast tx |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
LIBRARY ieee; |
USE ieee.std_logic_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use work.axi.all; |
use work.ipv4_types.all; |
use work.arp_types.all; |
|
|
ENTITY IPv4_TX_tb IS |
END IPv4_TX_tb; |
|
ARCHITECTURE behavior OF IPv4_TX_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT IPv4_TX |
PORT( |
-- IP Layer signals |
ip_tx_start : in std_logic; |
ip_tx : in ipv4_tx_type; -- IP tx cxns |
ip_tx_result : out std_logic_vector (1 downto 0); -- tx status (changes during transmission) |
ip_tx_data_out_ready : out std_logic; -- indicates IP TX is ready to take data |
|
-- system signals |
clk : in STD_LOGIC; -- same clock used to clock mac data and ip data |
reset : in STD_LOGIC; |
our_ip_address : in STD_LOGIC_VECTOR (31 downto 0); |
our_mac_address : in std_logic_vector (47 downto 0); |
-- ARP lookup signals |
arp_req_req : out arp_req_req_type; |
arp_req_rslt : in arp_req_rslt_type; |
-- MAC layer TX signals |
mac_tx_req : out std_logic; -- indicates that ip wants access to channel (stays up for as long as tx) |
mac_tx_granted : in std_logic; -- indicates that access to channel has been granted |
mac_data_out_ready : in std_logic; -- indicates system ready to consume data |
mac_data_out_valid : out std_logic; -- indicates data out is valid |
mac_data_out_first : out std_logic; -- with data out valid indicates the first byte of a frame |
mac_data_out_last : out std_logic; -- with data out valid indicates the last byte of a frame |
mac_data_out : out std_logic_vector (7 downto 0) -- ethernet frame (from dst mac addr through to last byte of frame) |
); |
END COMPONENT; |
|
|
--Inputs |
signal ip_tx_start : std_logic := '0'; |
signal ip_tx : ipv4_tx_type; |
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal our_ip_address : std_logic_vector(31 downto 0) := (others => '0'); |
signal our_mac_address : std_logic_vector(47 downto 0) := (others => '0'); |
signal mac_tx_granted : std_logic := '0'; |
signal mac_data_out_ready : std_logic := '0'; |
signal arp_req_rslt : arp_req_rslt_type; |
|
--Outputs |
signal ip_tx_result : std_logic_vector (1 downto 0); -- tx status (changes during transmission) |
signal ip_tx_data_out_ready : std_logic; -- indicates IP TX is ready to take data |
signal mac_tx_req : std_logic; |
signal mac_data_out_valid : std_logic; |
signal mac_data_out_last : std_logic; |
signal mac_data_out_first : std_logic; |
signal mac_data_out : std_logic_vector(7 downto 0); |
signal arp_req_req : arp_req_req_type; |
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: IPv4_TX PORT MAP ( |
ip_tx_start => ip_tx_start, |
ip_tx => ip_tx, |
ip_tx_result => ip_tx_result, |
ip_tx_data_out_ready => ip_tx_data_out_ready, |
clk => clk, |
reset => reset, |
our_ip_address => our_ip_address, |
our_mac_address => our_mac_address, |
arp_req_req => arp_req_req, |
arp_req_rslt => arp_req_rslt, |
mac_tx_req => mac_tx_req, |
mac_tx_granted => mac_tx_granted, |
mac_data_out_ready => mac_data_out_ready, |
mac_data_out_valid => mac_data_out_valid, |
mac_data_out_first => mac_data_out_first, |
mac_data_out_last => mac_data_out_last, |
mac_data_out => mac_data_out |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '0'; |
wait for clk_period/2; |
clk <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
our_ip_address <= x"c0a80509"; -- 192.168.5.9 |
our_mac_address <= x"002320212223"; |
ip_tx_start <= '0'; |
mac_tx_granted <= '0'; |
mac_data_out_ready <= '0'; |
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
arp_req_rslt.got_mac <= '0'; |
arp_req_rslt.got_err <= '0'; |
arp_req_rslt.mac <= (others => '0'); |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
-- check reset conditions |
assert arp_req_req.lookup_req = '0' report "arp_req_req.lookup_req not initialised correctly on reset"; |
assert ip_tx_result = IPTX_RESULT_NONE report "ip_tx_result not initialised correctly on reset"; |
assert ip_tx_data_out_ready = '0' report "ip_tx_data_out_ready not initialised correctly on reset"; |
assert mac_tx_req = '0' report "mac_tx_req not initialised correctly on reset"; |
assert mac_data_out_valid = '0' report "mac_data_out_valid not initialised correctly on reset"; |
assert mac_data_out_last = '0' report "mac_data_out_last not initialised correctly on reset"; |
|
-- insert stimulus here |
|
------------ |
-- TEST 1 -- basic functional tx test with some delays for arp and chn access |
------------ |
|
report "T1: basic functional tx test with some delays for arp and chn access"; |
|
ip_tx.hdr.protocol <= x"35"; |
ip_tx.hdr.data_length <= x"0008"; |
ip_tx.hdr.dst_ip_addr <= x"c0123478"; |
ip_tx_start <= '1'; |
wait for clk_period; |
ip_tx_start <= '0'; |
arp_req_rslt.got_mac <= '0'; |
arp_req_rslt.got_err <= '0'; |
|
assert arp_req_req.lookup_req = '1' report "T1: lookup_req not set on tx start"; |
wait for clk_period; |
assert ip_tx_result = IPTX_RESULT_SENDING report "T1: result should be IPTX_RESULT_SENDING"; |
|
wait for clk_period*10; -- simulate arp lookup time |
arp_req_rslt.mac <= x"050423271016"; |
arp_req_rslt.got_mac <= '1'; |
|
wait for clk_period*2; |
|
assert arp_req_req.lookup_req = '0' report "T1: lookup_req not clear after setting"; |
assert mac_tx_req = '1' report "T1: mac_tx_req not set after getting mac"; |
|
wait for clk_period*10; -- simulate mac chn access time |
mac_tx_granted <= '1'; |
wait for clk_period*2; |
mac_data_out_ready <= '1'; |
assert mac_data_out_valid = '0' report "T1: mac_data_out_valid asserted too early"; |
|
wait for clk_period; |
|
assert ip_tx_data_out_ready = '0' report "T1: IP data out ready asserted too early"; |
wait for clk_period; |
assert mac_data_out_valid = '1' report "T1: mac_data_out_valid not asserted"; |
|
-- wait until in eth hdr |
wait for clk_period*3; |
-- go mac not ready for 2 clocks |
mac_data_out_ready <= '0'; |
wait for clk_period*2; |
mac_data_out_ready <= '1'; |
|
|
wait until ip_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
ip_tx.data.data_out_valid <= '1'; |
ip_tx.data.data_out <= x"56"; wait for clk_period; |
-- delay data in for 1 clk cycle |
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out <= x"57"; wait for clk_period; |
ip_tx.data.data_out_valid <= '1'; wait for clk_period; |
ip_tx.data.data_out <= x"58"; wait for clk_period; |
ip_tx.data.data_out <= x"59"; wait for clk_period; |
|
-- delay mac ready for 2 clk cycles |
mac_data_out_ready <= '0'; |
ip_tx.data.data_out <= x"5a"; wait for clk_period; |
assert ip_tx_data_out_ready = '0' report "T1: ip_tx_data_out_ready not cleared when mac not ready"; |
|
ip_tx.data.data_out <= x"5a"; wait for clk_period; |
mac_data_out_ready <= '1'; |
wait until ip_tx_data_out_ready = '1'; |
wait for clk_period; |
assert ip_tx_data_out_ready = '1' report "T1: ip_tx_data_out_ready not set when mac ready"; |
ip_tx.data.data_out <= x"5b"; wait for clk_period; |
ip_tx.data.data_out <= x"5c"; wait for clk_period; |
|
ip_tx.data.data_out <= x"5d"; |
ip_tx.data.data_out_last <= '1'; |
wait for clk_period; |
assert mac_data_out_last = '1' report "T1: mac_datda_out_last not set on last byte"; |
|
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period*2; |
|
assert ip_tx_result = IPTX_RESULT_SENT report "T1: result should be IPTX_RESULT_SENT"; |
assert mac_tx_req = '0' report "T1: mac_tx_req held on too long after TX"; |
|
mac_tx_granted <= '0'; |
wait for clk_period*2; |
|
------------ |
-- TEST 2 -- basic functional tx test with no delays for arp and chn access |
------------ |
|
report "T2: basic functional tx test with no delays for arp and chn access"; |
|
ip_tx.hdr.protocol <= x"11"; |
ip_tx.hdr.data_length <= x"0006"; |
ip_tx.hdr.dst_ip_addr <= x"c0123478"; |
ip_tx_start <= '1'; |
wait for clk_period; |
ip_tx_start <= '0'; wait for clk_period; |
arp_req_rslt.got_mac <= '0'; |
|
assert arp_req_req.lookup_req = '1' report "T2: lookup_req not set on tx start"; |
assert ip_tx_result = IPTX_RESULT_SENDING report "T2: result should be IPTX_RESULT_SENDING"; |
|
wait for clk_period; -- simulate arp lookup time |
arp_req_rslt.mac <= x"050423271016"; |
arp_req_rslt.got_mac <= '1'; |
|
wait for clk_period*2; |
|
assert arp_req_req.lookup_req = '0' report "T2: lookup_req not clear after setting"; |
assert mac_tx_req = '1' report "T2: mac_tx_req not set after getting mac"; |
|
wait for clk_period; -- simulate mac chn access time |
mac_tx_granted <= '1'; |
wait for clk_period*2; |
mac_data_out_ready <= '1'; |
|
assert ip_tx_data_out_ready = '0' report "T2: IP data out ready asserted too early"; |
|
wait until ip_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
ip_tx.data.data_out_valid <= '1'; |
ip_tx.data.data_out <= x"c1"; wait for clk_period; |
ip_tx.data.data_out <= x"c2"; wait for clk_period; |
ip_tx.data.data_out <= x"c3"; wait for clk_period; |
ip_tx.data.data_out <= x"c4"; wait for clk_period; |
ip_tx.data.data_out <= x"c5"; wait for clk_period; |
|
ip_tx.data.data_out <= x"c6"; |
ip_tx.data.data_out_last <= '1'; |
wait for clk_period; |
|
assert mac_data_out_last = '1' report "T2: mac_datda_out_last not set on last byte"; |
|
|
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period*2; |
|
assert ip_tx_result = IPTX_RESULT_SENT report "T2: result should be IPTX_RESULT_SENT"; |
assert mac_tx_req = '0' report "T2: mac_tx_req held on too long after TX"; |
|
mac_tx_granted <= '0'; |
wait for clk_period*2; |
|
------------ |
-- TEST 3 -- tx test for IP broadcast, should be no arp req |
------------ |
|
report "T3: tx test for IP broadcast, should be no arp req"; |
|
ip_tx.hdr.protocol <= x"11"; |
ip_tx.hdr.data_length <= x"0006"; |
ip_tx.hdr.dst_ip_addr <= x"ffffffff"; |
ip_tx_start <= '1'; |
wait for clk_period; |
ip_tx_start <= '0'; wait for clk_period; |
arp_req_rslt.got_mac <= '0'; |
|
assert arp_req_req.lookup_req = '0' report "T3: its trying to do an ARP req tx start"; |
assert ip_tx_result = IPTX_RESULT_SENDING report "T3: result should be IPTX_RESULT_SENDING"; |
|
wait for clk_period; -- simulate mac chn access time |
mac_tx_granted <= '1'; |
wait for clk_period*2; |
mac_data_out_ready <= '1'; |
|
assert ip_tx_data_out_ready = '0' report "T3: IP data out ready asserted too early"; |
|
wait until ip_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
ip_tx.data.data_out_valid <= '1'; |
ip_tx.data.data_out <= x"c1"; wait for clk_period; |
ip_tx.data.data_out <= x"c2"; wait for clk_period; |
ip_tx.data.data_out <= x"c3"; wait for clk_period; |
ip_tx.data.data_out <= x"c4"; wait for clk_period; |
ip_tx.data.data_out <= x"c5"; wait for clk_period; |
|
ip_tx.data.data_out <= x"c6"; |
ip_tx.data.data_out_last <= '1'; |
wait for clk_period; |
|
assert mac_data_out_last = '1' report "T3: mac_datda_out_last not set on last byte"; |
|
|
ip_tx.data.data_out_valid <= '0'; |
ip_tx.data.data_out_last <= '0'; |
wait for clk_period*2; |
|
assert ip_tx_result = IPTX_RESULT_SENT report "T3: result should be IPTX_RESULT_SENT"; |
assert mac_tx_req = '0' report "T3: mac_tx_req held on too long after TX"; |
|
mac_tx_granted <= '0'; |
wait for clk_period*2; |
|
|
report "--- end of tests ---"; |
|
wait; |
end process; |
|
END; |
/UDP_complete_nomac_tb.vhd
0,0 → 1,1546
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 09:57:01 06/13/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/udp1/UDP_complete_nomac_tb.vhd |
-- Project Name: udp1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: UDP_Complete_nomac |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Revision 0.02 - Added test for IP broadcast tx |
-- Revision 0.03 - Added tests for ARP timeout |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
library IEEE; |
use IEEE.STD_LOGIC_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use work.axi.all; |
use work.ipv4_types.all; |
use work.arp_types.all; |
|
ENTITY UDP_complete_nomac_tb IS |
END UDP_complete_nomac_tb; |
|
ARCHITECTURE behavior OF UDP_complete_nomac_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT UDP_Complete_nomac |
generic ( |
CLOCK_FREQ : integer := 125000000; -- freq of data_in_clk -- needed to timout cntr |
ARP_TIMEOUT : integer := 60 -- ARP response timeout (s) |
); |
Port ( |
-- UDP TX signals |
udp_tx_start : in std_logic; -- indicates req to tx UDP |
udp_txi : in udp_tx_type; -- UDP tx cxns |
udp_tx_result : out std_logic_vector (1 downto 0);-- tx status (changes during transmission) |
udp_tx_data_out_ready: out std_logic; -- indicates udp_tx is ready to take data |
-- UDP RX signals |
udp_rx_start : out std_logic; -- indicates receipt of udp header |
udp_rxo : out udp_rx_type; |
-- IP RX signals |
ip_rx_hdr : out ipv4_rx_header_type; |
-- system signals |
rx_clk : in STD_LOGIC; |
tx_clk : in STD_LOGIC; |
reset : in STD_LOGIC; |
our_ip_address : in STD_LOGIC_VECTOR (31 downto 0); |
our_mac_address : in std_logic_vector (47 downto 0); |
control : in udp_control_type; |
-- status signals |
arp_pkt_count : out STD_LOGIC_VECTOR(7 downto 0); -- count of arp pkts received |
ip_pkt_count : out STD_LOGIC_VECTOR(7 downto 0); -- number of IP pkts received for us |
-- MAC Transmitter |
mac_tx_tdata : out std_logic_vector(7 downto 0); -- data byte to tx |
mac_tx_tvalid : out std_logic; -- tdata is valid |
mac_tx_tready : in std_logic; -- mac is ready to accept data |
mac_tx_tfirst : out std_logic; -- indicates first byte of frame |
mac_tx_tlast : out std_logic; -- indicates last byte of frame |
-- MAC Receiver |
mac_rx_tdata : in std_logic_vector(7 downto 0); -- data byte received |
mac_rx_tvalid : in std_logic; -- indicates tdata is valid |
mac_rx_tready : out std_logic; -- tells mac that we are ready to take data |
mac_rx_tlast : in std_logic -- indicates last byte of the trame |
); |
END COMPONENT; |
|
|
|
type state_type is (IDLE, WAIT_RX_DONE, DATA_OUT); |
type count_mode_type is (RST, INCR, HOLD); |
type set_clr_type is (SET, CLR, HOLD); |
|
|
--Inputs |
signal udp_tx_start_int : std_logic := '0'; |
signal udp_tx_int : udp_tx_type; |
signal clk_int : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal our_ip_address : std_logic_vector(31 downto 0) := (others => '0'); |
signal our_mac_address : std_logic_vector(47 downto 0) := (others => '0'); |
signal mac_tx_tready : std_logic := '0'; |
signal mac_rx_tdata : std_logic_vector(7 downto 0) := (others => '0'); |
signal mac_rx_tvalid : std_logic := '0'; |
signal mac_rx_tlast : std_logic := '0'; |
signal control : udp_control_type; |
|
--Outputs |
signal udp_rx_start_int : std_logic; |
signal udp_rx_int : udp_rx_type; |
signal ip_rx_hdr : ipv4_rx_header_type; |
signal udp_tx_result : std_logic_vector (1 downto 0); |
signal udp_tx_data_out_ready_int: std_logic; |
|
signal arp_pkt_count : std_logic_vector(7 downto 0); |
signal ip_pkt_count : std_logic_vector(7 downto 0); |
signal mac_tx_tdata : std_logic_vector(7 downto 0); |
signal mac_tx_tvalid : std_logic; |
signal mac_tx_tfirst : std_logic; |
signal mac_tx_tlast : std_logic; |
signal mac_rx_tready : std_logic; |
|
signal pbtx_led : std_logic; |
signal pbtx : std_logic := '0'; |
|
-- state signals |
signal state : state_type; |
signal count : unsigned (7 downto 0); |
signal tx_hdr : udp_tx_header_type; |
signal tx_start_reg : std_logic; |
signal tx_started_reg : std_logic; |
signal tx_fin_reg : std_logic; |
|
|
-- control signals |
signal next_state : state_type; |
signal set_state : std_logic; |
signal set_count : count_mode_type; |
signal set_hdr : std_logic; |
signal set_tx_start : set_clr_type; |
signal set_last : std_logic; |
signal set_tx_started : set_clr_type; |
signal set_tx_fin : set_clr_type; |
signal first_byte_rx : STD_LOGIC_VECTOR(7 downto 0); |
|
|
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: UDP_Complete_nomac |
generic map ( |
CLOCK_FREQ => 10, -- artificially low count to enable pragmatic testing |
ARP_TIMEOUT => 20 |
) |
PORT MAP ( |
udp_tx_start => udp_tx_start_int, |
udp_txi => udp_tx_int, |
udp_tx_result => udp_tx_result, |
udp_tx_data_out_ready => udp_tx_data_out_ready_int, |
udp_rx_start => udp_rx_start_int, |
udp_rxo => udp_rx_int, |
ip_rx_hdr => ip_rx_hdr, |
rx_clk => clk_int, |
tx_clk => clk_int, |
reset => reset, |
our_ip_address => our_ip_address, |
our_mac_address => our_mac_address, |
control => control, |
arp_pkt_count => arp_pkt_count, |
ip_pkt_count => ip_pkt_count, |
mac_tx_tdata => mac_tx_tdata, |
mac_tx_tvalid => mac_tx_tvalid, |
mac_tx_tready => mac_tx_tready, |
mac_tx_tfirst => mac_tx_tfirst, |
mac_tx_tlast => mac_tx_tlast, |
mac_rx_tdata => mac_rx_tdata, |
mac_rx_tvalid => mac_rx_tvalid, |
mac_rx_tready => mac_rx_tready, |
mac_rx_tlast => mac_rx_tlast |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk_int <= '0'; |
wait for clk_period/2; |
clk_int <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 100 ns; |
|
our_ip_address <= x"c0a80509"; -- 192.168.5.9 |
our_mac_address <= x"002320212223"; |
control.ip_controls.arp_controls.clear_cache <= '0'; |
mac_tx_tready <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
-- check reset conditions |
assert udp_tx_result = UDPTX_RESULT_NONE report "udp_tx_result not initialised correctly on reset"; |
assert udp_tx_data_out_ready_int = '0' report "ip_udp_txitx.data.data_out_ready not initialised correctly on reset"; |
assert mac_tx_tvalid = '0' report "mac_tx_tvalid not initialised correctly on reset"; |
assert mac_tx_tlast = '0' report "mac_tx_tlast not initialised correctly on reset"; |
assert arp_pkt_count = x"00" report "arp_pkt_count not initialised correctly on reset"; |
assert ip_pkt_count = x"00" report "ip_pkt_count not initialised correctly on reset"; |
assert udp_rx_start_int = '0' report "udp_rx_start not initialised correctly on reset"; |
assert udp_rx_int.hdr.is_valid = '0' report "udp_rx_int.hdr.is_valid not initialised correctly on reset"; |
assert udp_rx_int.hdr.data_length = x"0000" report "udp_rx_int.hdr.data_length not initialised correctly on reset"; |
assert udp_rx_int.hdr.src_ip_addr = x"00000000" report "udp_rx_int.hdr.src_ip_addr not initialised correctly on reset"; |
assert udp_rx_int.hdr.src_port = x"0000" report "udp_rx_int.hdr.src_port not initialised correctly on reset"; |
assert udp_rx_int.hdr.dst_port = x"0000" report "udp_rx_int.hdr.dst_port not initialised correctly on reset"; |
assert udp_rx_int.data.data_in = x"00" report "udp_rx_start.data.data_in not initialised correctly on reset"; |
assert udp_rx_int.data.data_in_valid = '0' report "udp_rx_start.data.data_in_valid not initialised correctly on reset"; |
assert udp_rx_int.data.data_in_last = '0' report "udp_rx_start.data.data_in_last not initialised correctly on reset"; |
assert ip_rx_hdr.is_valid = '0' report "ip_rx_hdr.is_valid not initialised correctly on reset"; |
assert ip_rx_hdr.protocol = x"00" report "ip_rx_hdr.protocol not initialised correctly on reset"; |
assert ip_rx_hdr.data_length = x"0000" report "ip_rx_hdr.data_length not initialised correctly on reset"; |
assert ip_rx_hdr.src_ip_addr = x"00000000" report "ip_rx_hdr.src_ip_addr not initialised correctly on reset"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "ip_rx_hdr.num_frame_errors not initialised correctly on reset"; |
|
|
-- insert stimulus here |
|
------------ |
-- TEST 1 -- send ARP request |
------------ |
|
report "T1: Send an ARP request: who has 192.168.5.9? Tell 192.168.5.1"; |
|
mac_tx_tready <= '1'; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- HW type |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Protocol type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- HW size |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- protocol size |
mac_rx_tdata <= x"04"; wait for clk_period; |
-- Opcode |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Sender MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- Sender IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Target MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- Target IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '1'; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
|
-- check we got the ARP pkt |
assert arp_pkt_count = x"01" report "T1: arp_pkt_count wrong value"; |
assert ip_pkt_count = x"00" report "T1: ip_pkt_count wrong value"; |
assert udp_tx_result = UDPTX_RESULT_NONE report "T1: udp_tx_result wrong value"; |
assert udp_tx_data_out_ready_int = '0' report "T1: ip_udp_txitx.data.data_out_ready wrong value"; |
assert udp_rx_start_int = '0' report "T1: udp_rx_start wrong value"; |
assert udp_rx_int.hdr.is_valid = '0' report "T1: udp_rx_int.hdr.is_valid wrong value"; |
assert ip_rx_hdr.is_valid = '0' report "T1: ip_rx_hdr.is_valid wrong value"; |
|
-- check we tx a response |
|
wait for clk_period*25; |
assert mac_tx_tvalid = '1' report "T1: not transmitting a response"; |
wait for clk_period*25; |
assert mac_tx_tvalid = '0' report "T1: tx held on for too long"; |
|
------------ |
-- TEST 2 -- send UDP pkt (same as sample from Java program) |
------------ |
|
report "T2: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"68"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T2: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T2: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T2: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T2: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T2: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T2: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T2: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T2: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T2: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T2: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T2: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T2: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T2: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T2: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T2: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T2: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T2: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T2: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"01" report "T2: ip pkt cnt incorrect"; |
|
wait for clk_period*20; |
|
------------ |
-- TEST 3 -- send UDP pkt again (same as sample from Java program) |
------------ |
|
report "T3: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"68"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T3: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T3: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T3: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T3: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T3: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T3: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T3: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T3: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T3: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T3: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T3: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T3: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T3: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T3: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T3: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T3: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T3: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T3: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"02" report "T3: ip pkt cnt incorrect"; |
|
wait for clk_period*50; |
|
------------ |
-- TEST 4 -- send UDP pkt with specific UDP data to force a broadcast tx in reply |
------------ |
|
report "T4: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"42"; wait for clk_period; -- First byte 'B' triggers a reply to broadcast addr |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T4: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T4: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T4: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T4: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T4: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T4: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T4: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T4: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T4: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T4: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T4: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T4: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T4: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
report "T4: waiting for mac data tx"; |
wait until mac_tx_tvalid = '1'; |
report "T4: starting mac data tx"; |
wait for clk_period; |
|
-- check the mac data being transmitted |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T4: incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T4: incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T4: incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T4: incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T4: incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T4: incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T4: incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"45" report "T4: incorrect ver.hlen"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect srv type"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect len 0"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T4: incorrect len 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T4: incorrect ident 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect ident 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect flag&frag 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect flag&frag 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"80" report "T4: incorrect TTL"; wait for clk_period; |
assert mac_tx_tdata = x"11" report "T4: incorrect protocol"; wait for clk_period; |
assert mac_tx_tdata = x"75" report "T4: incorrect hdr.cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"1c" report "T4: incorrect hdr.cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T4: incorrect src ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T4: incorrect src ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T4: incorrect src ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T4: incorrect src ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"ff" report "T4: incorrect dst ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T4: incorrect dst ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"26" report "T4: incorrect src port 0"; wait for clk_period; |
assert mac_tx_tdata = x"94" report "T4: incorrect src port 1"; wait for clk_period; |
assert mac_tx_tdata = x"f4" report "T4: incorrect dst port 0"; wait for clk_period; |
assert mac_tx_tdata = x"9a" report "T4: incorrect dst port 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T4: incorrect udp len 0"; wait for clk_period; |
assert mac_tx_tdata = x"0c" report "T4: incorrect udp len 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect udp cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T4: incorrect udp cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"40" report "T4: incorrect udp data 0"; wait for clk_period; |
assert mac_tx_tdata = x"41" report "T4: incorrect udp data 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"42" report "T4: incorrect udp data 2"; |
assert mac_tx_tlast = '0' report "T4: tlast asserted too soon"; wait for clk_period; |
assert mac_tx_tdata = x"43" report "T4: incorrect udp data 3"; |
assert mac_tx_tlast = '1' report "T4: tlast not asserted"; wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENT report "T4: TX did not complete"; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T4: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T4: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T4: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T4: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T4: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"03" report "T4: ip pkt cnt incorrect"; |
|
------------ |
-- TEST 5 -- send UDP pkt with dst=bc addr to ensure we can receive broadcast tx |
------------ |
|
report "T5: Send UDP IP pkt dst ip_address bc, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"68"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T5: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T5: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T5: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T5: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T5: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T5: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T5: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T5: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T5: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T5: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T5: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T5: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T5: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
|
report "T5: waiting for mac data tx"; |
if mac_tx_tvalid = '0' then |
wait until mac_tx_tvalid = '1'; |
wait for clk_period; |
end if; |
report "T5: starting mac data tx"; |
|
-- check the mac data being transmitted |
assert mac_tx_tdata = x"00" report "T5: incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T5: incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"18" report "T5: incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"29" report "T5: incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"26" report "T5: incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"7c" report "T5: incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T5: incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T5: incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T5: incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T5: incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T5: incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T5: incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T5: incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"45" report "T5: incorrect ver.hlen"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect srv type"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect len 0"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T5: incorrect len 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T5: incorrect ident 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect ident 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect flag&frag 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect flag&frag 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"80" report "T5: incorrect TTL"; wait for clk_period; |
assert mac_tx_tdata = x"11" report "T5: incorrect protocol"; wait for clk_period; |
assert mac_tx_tdata = x"af" report "T5: incorrect hdr.cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"72" report "T5: incorrect hdr.cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T5: incorrect src ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T5: incorrect src ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T5: incorrect src ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T5: incorrect src ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T5: incorrect dst ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T5: incorrect dst ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T5: incorrect dst ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T5: incorrect dst ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"26" report "T5: incorrect src port 0"; wait for clk_period; |
assert mac_tx_tdata = x"94" report "T5: incorrect src port 1"; wait for clk_period; |
assert mac_tx_tdata = x"f4" report "T5: incorrect dst port 0"; wait for clk_period; |
assert mac_tx_tdata = x"9a" report "T5: incorrect dst port 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T5: incorrect udp len 0"; wait for clk_period; |
assert mac_tx_tdata = x"0c" report "T5: incorrect udp len 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect udp cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T5: incorrect udp cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"50" report "T5: incorrect udp data 0"; wait for clk_period; |
assert mac_tx_tdata = x"51" report "T5: incorrect udp data 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"52" report "T5: incorrect udp data 2"; |
assert mac_tx_tlast = '0' report "T5: tlast asserted too soon"; wait for clk_period; |
assert mac_tx_tdata = x"53" report "T5: incorrect udp data 3"; |
assert mac_tx_tlast = '1' report "T5: tlast not asserted"; wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENT report "T5: TX did not complete"; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T5: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T5: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T5: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T5: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T5: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"04" report "T5: ip pkt cnt incorrect"; |
|
|
------------ |
-- TEST 6 -- send UDP pkt with data to trigger the sending of a pkt to unknown IP addr to force an ARP timeout |
------------ |
|
report "T6: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694 with data x43 to trig tx to unknown IP"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"43"; wait for clk_period; -- First byte 'C' triggers a reply to unknown addr |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T6: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T6: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T6: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T6: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T6: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T6: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T6: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T6: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T6: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T6: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T6: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T6: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T6: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
report "T6: waiting for mac data tx"; |
wait until mac_tx_tvalid = '1'; |
report "T6: starting mac data tx"; |
wait for clk_period; |
|
-- check the mac data being transmitted is valid ARP request |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T6: incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T6: incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T6: incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T6: incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T6: incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T6: incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T6: incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T6: incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"06" report "T6: incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T6: incorrect HW type.0"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T6: incorrect HW type.1"; wait for clk_period; |
assert mac_tx_tdata = x"08" report "T6: incorrect prot.0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect prot.1"; wait for clk_period; |
assert mac_tx_tdata = x"06" report "T6: incorrect HW size"; wait for clk_period; |
assert mac_tx_tdata = x"04" report "T6: incorrect prot size"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect opcode.0"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T6: incorrect opcode.1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T6: incorrect sndr mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T6: incorrect sndr mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T6: incorrect sndr mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T6: incorrect sndr mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T6: incorrect sndr mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T6: incorrect sndr mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T6: incorrect sndr ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T6: incorrect sndr ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T6: incorrect sndr ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T6: incorrect sndr ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T6: incorrect trg mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T6: incorrect trg ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"bb" report "T6: incorrect trg ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"cc" report "T6: incorrect trg ip 2"; |
assert mac_tx_tlast = '0' report "T6: tlast asserted too soon"; |
wait for clk_period; |
|
assert mac_tx_tdata = x"dd" report "T6: incorrect trg ip 3"; |
assert mac_tx_tlast = '1' report "T6: tlast should be set"; |
wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENDING report "T6: TX should still be in sending phase"; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T6: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T6: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T6: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T6: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T6: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"05" report "T6: ip pkt cnt incorrect"; |
|
-- check for error on tx as a result of ARP timeout |
|
wait for clk_period*10*20; |
assert udp_tx_result = IPTX_RESULT_ERR report "T6: TX should resulkt in error (arp timeout)"; |
|
wait for clk_period*10; |
|
------------ |
-- TEST 7 -- send UDP pkt again to ensure that we can rx a pkt and tx after a timeout |
------------ |
|
report "T7: Send UDP IP pkt dst ip_address c0a80509, from port f49a to port 2694"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"18"; wait for clk_period; |
mac_rx_tdata <= x"29"; wait for clk_period; |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"7c"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; -- IP pkt |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_rx_tdata <= x"45"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- total len |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
-- ID |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"7a"; wait for clk_period; |
-- flags & frag |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- TTL |
mac_rx_tdata <= x"80"; wait for clk_period; |
-- Protocol |
mac_rx_tdata <= x"11"; wait for clk_period; |
-- Header CKS |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- SRC IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- DST IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
-- SRC port |
mac_rx_tdata <= x"f4"; wait for clk_period; |
mac_rx_tdata <= x"9a"; wait for clk_period; |
-- DST port |
mac_rx_tdata <= x"26"; wait for clk_period; |
mac_rx_tdata <= x"94"; wait for clk_period; |
-- length |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"0d"; wait for clk_period; |
-- cks |
mac_rx_tdata <= x"8b"; wait for clk_period; |
mac_rx_tdata <= x"79"; wait for clk_period; |
-- user data |
mac_rx_tdata <= x"68"; wait for clk_period; |
|
-- since we are up to the user data stage, the header should be valid and the data_in_valid should be set |
assert udp_rx_int.hdr.is_valid = '1' report "T7: udp_rx_int.hdr.is_valid not set"; |
assert udp_rx_int.hdr.data_length = x"0005" report "T7: udp_rx_int.hdr.data_length not set correctly"; |
assert udp_rx_int.hdr.src_ip_addr = x"c0a80501" report "T7: udp_rx_int.hdr.src_ip_addr not set correctly"; |
assert udp_rx_int.hdr.src_port = x"f49a" report "T7: udp_rx_int.hdr.src_port not set correctly"; |
assert udp_rx_int.hdr.dst_port = x"2694" report "T7: udp_rx_int.hdr.dst_port not set correctly"; |
|
assert udp_rx_start_int = '1' report "T7: udp_rx_start not set"; |
assert udp_rx_int.data.data_in_valid = '1' report "T7: udp_rx_int.data.data_in_valid not set"; |
|
assert ip_rx_hdr.is_valid = '1' report "T7: ip_rx_hdr.is_valid not set"; |
assert ip_rx_hdr.protocol = x"11" report "T7: ip_rx_hdr.protocol not set correctly"; |
assert ip_rx_hdr.src_ip_addr = x"c0a80501" report "T7: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T7: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx_hdr.last_error_code = x"0" report "T7: ip_rx.hdr.last_error_code not set correctly"; |
|
-- put the rest of the user data |
mac_rx_tdata <= x"65"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6c"; wait for clk_period; |
mac_rx_tdata <= x"6f"; mac_rx_tlast <= '1'; wait for clk_period; |
|
assert udp_rx_int.data.data_in_last = '1' report "T7: udp_rx_int.data.data_in_last not set"; |
|
mac_rx_tdata <= x"00"; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
report "T7: waiting for mac ARP REQ data tx"; |
if mac_tx_tvalid = '0' then |
wait until mac_tx_tvalid = '1'; |
wait for clk_period; |
end if; |
report "T7: starting mac ARP REQ data tx"; |
|
-- check the ARP REQ mac data being transmitted |
assert mac_tx_tdata = x"ff" report "T7: arp incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T7: arp incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T7: arp incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T7: arp incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T7: arp incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"ff" report "T7: arp incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: arp incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: arp incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T7: arp incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T7: arp incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T7: arp incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: arp incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T7: arp incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"06" report "T7: arp incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: arp incorrect HW type.0"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T7: arp incorrect HW type.1"; wait for clk_period; |
assert mac_tx_tdata = x"08" report "T7: arp incorrect prot.0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: arp incorrect prot.1"; wait for clk_period; |
assert mac_tx_tdata = x"06" report "T7: arp incorrect HW size"; wait for clk_period; |
assert mac_tx_tdata = x"04" report "T7: arp incorrect prot size"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: arp incorrect opcode.0"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T7: arp incorrect opcode.1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: arp incorrect sndr mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: arp incorrect sndr mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T7: arp incorrect sndr mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T7: arp incorrect sndr mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T7: arp incorrect sndr mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: arp incorrect sndr mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T7: arp incorrect sndr ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T7: arp incorrect sndr ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T7: arp incorrect sndr ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T7: arp incorrect sndr ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: arp incorrect trg mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: arp incorrect trg mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: arp incorrect trg mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: arp incorrect trg mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: arp incorrect trg mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: arp incorrect trg mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T7: arp incorrect trg ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T7: arp incorrect trg ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T7: arp incorrect trg ip 2"; |
assert mac_tx_tlast = '0' report "T7: arp tlast asserted too soon"; |
wait for clk_period; |
|
assert mac_tx_tdata = x"01" report "T7: arp incorrect trg ip 3"; |
assert mac_tx_tlast = '1' report "T7: arp tlast should be set"; |
wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENDING report "T7: arp TX should still be in sending phase"; |
|
wait for clk_period*5; |
|
report "T7: feeding in an arp reply: I have c0180501 at mac 021503230454"; |
|
mac_rx_tvalid <= '1'; |
-- dst MAC (bc) |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
mac_rx_tdata <= x"ff"; wait for clk_period; |
-- src MAC |
mac_rx_tdata <= x"02"; wait for clk_period; |
mac_rx_tdata <= x"15"; wait for clk_period; |
mac_rx_tdata <= x"03"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"04"; wait for clk_period; |
mac_rx_tdata <= x"54"; wait for clk_period; |
-- type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- HW type |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Protocol type |
mac_rx_tdata <= x"08"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
-- HW size |
mac_rx_tdata <= x"06"; wait for clk_period; |
-- protocol size |
mac_rx_tdata <= x"04"; wait for clk_period; |
-- Opcode |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"02"; wait for clk_period; |
-- Sender MAC |
mac_rx_tdata <= x"02"; wait for clk_period; |
mac_rx_tdata <= x"15"; wait for clk_period; |
mac_rx_tdata <= x"03"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"04"; wait for clk_period; |
mac_rx_tdata <= x"54"; wait for clk_period; |
-- Sender IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"01"; wait for clk_period; |
-- Target MAC |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
mac_rx_tdata <= x"20"; wait for clk_period; |
mac_rx_tdata <= x"21"; wait for clk_period; |
mac_rx_tdata <= x"22"; wait for clk_period; |
mac_rx_tdata <= x"23"; wait for clk_period; |
-- Target IP |
mac_rx_tdata <= x"c0"; wait for clk_period; |
mac_rx_tdata <= x"a8"; wait for clk_period; |
mac_rx_tdata <= x"05"; wait for clk_period; |
mac_rx_tdata <= x"09"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '1'; |
mac_rx_tdata <= x"00"; wait for clk_period; |
mac_rx_tlast <= '0'; |
mac_rx_tvalid <= '0'; |
wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENDING report "T7: TX should still be sending"; |
|
report "T7: waiting for mac data tx"; |
if mac_tx_tvalid = '0' then |
wait until mac_tx_tvalid = '1'; |
wait for clk_period; |
end if; |
report "T7: starting mac data tx"; |
|
-- check the mac data being transmitted |
assert mac_tx_tdata = x"02" report "T7: incorrect dst mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"15" report "T7: incorrect dst mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"03" report "T7: incorrect dst mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: incorrect dst mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"04" report "T7: incorrect dst mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"54" report "T7: incorrect dst mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: incorrect src mac 0"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: incorrect src mac 1"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T7: incorrect src mac 2"; wait for clk_period; |
assert mac_tx_tdata = x"21" report "T7: incorrect src mac 3"; wait for clk_period; |
assert mac_tx_tdata = x"22" report "T7: incorrect src mac 4"; wait for clk_period; |
assert mac_tx_tdata = x"23" report "T7: incorrect src mac 5"; wait for clk_period; |
|
assert mac_tx_tdata = x"08" report "T7: incorrect pkt_type 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect pkt type 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"45" report "T7: incorrect ver.hlen"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect srv type"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect len 0"; wait for clk_period; |
assert mac_tx_tdata = x"20" report "T7: incorrect len 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: incorrect ident 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect ident 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect flag&frag 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect flag&frag 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"80" report "T7: incorrect TTL"; wait for clk_period; |
assert mac_tx_tdata = x"11" report "T7: incorrect protocol"; wait for clk_period; |
assert mac_tx_tdata = x"af" report "T7: incorrect hdr.cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"72" report "T7: incorrect hdr.cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T7: incorrect src ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T7: incorrect src ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T7: incorrect src ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"09" report "T7: incorrect src ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"c0" report "T7: incorrect dst ip 0"; wait for clk_period; |
assert mac_tx_tdata = x"a8" report "T7: incorrect dst ip 1"; wait for clk_period; |
assert mac_tx_tdata = x"05" report "T7: incorrect dst ip 2"; wait for clk_period; |
assert mac_tx_tdata = x"01" report "T7: incorrect dst ip 3"; wait for clk_period; |
|
assert mac_tx_tdata = x"26" report "T7: incorrect src port 0"; wait for clk_period; |
assert mac_tx_tdata = x"94" report "T7: incorrect src port 1"; wait for clk_period; |
assert mac_tx_tdata = x"f4" report "T7: incorrect dst port 0"; wait for clk_period; |
assert mac_tx_tdata = x"9a" report "T7: incorrect dst port 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"00" report "T7: incorrect udp len 0"; wait for clk_period; |
assert mac_tx_tdata = x"0c" report "T7: incorrect udp len 1"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect udp cks 0"; wait for clk_period; |
assert mac_tx_tdata = x"00" report "T7: incorrect udp cks 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"40" report "T7: incorrect udp data 0"; wait for clk_period; |
assert mac_tx_tdata = x"41" report "T7: incorrect udp data 1"; wait for clk_period; |
|
assert mac_tx_tdata = x"42" report "T7: incorrect udp data 2"; |
assert mac_tx_tlast = '0' report "T7: tlast asserted too soon"; wait for clk_period; |
assert mac_tx_tdata = x"43" report "T7: incorrect udp data 3"; |
assert mac_tx_tlast = '1' report "T7: tlast not asserted"; wait for clk_period; |
|
assert udp_tx_result = IPTX_RESULT_SENT report "T7: TX did not complete"; |
|
assert udp_rx_int.data.data_in_valid = '0' report "T7: udp_rx_int.data.data_in_valid not cleared"; |
assert udp_rx_int.data.data_in_last = '0' report "T7: udp_rx_int.data.data_in_last not cleared"; |
assert udp_rx_start_int = '0' report "T7: udp_rx_start not cleared"; |
assert ip_rx_hdr.num_frame_errors = x"00" report "T7: ip_rx_hdr.num_frame_errors non zero at end of test"; |
assert ip_rx_hdr.last_error_code = x"0" report "T7: ip_rx_hdr.last_error_code indicates error at end of test"; |
assert ip_pkt_count = x"06" report "T7: ip pkt cnt incorrect"; |
|
|
report "--- end of tests ---"; |
wait; |
end process; |
|
-- AUTO TX process - on receipt of any UDP pkt, send a response. data sent is modified if a broadcast was received. |
|
-- TX response process - COMB |
tx_proc_combinatorial: process( |
-- inputs |
udp_rx_start_int, udp_rx_int, udp_tx_data_out_ready_int, udp_tx_result, ip_rx_hdr, |
udp_tx_int.data.data_out_valid, PBTX, |
-- state |
state, count, tx_hdr, tx_start_reg, tx_started_reg, tx_fin_reg, |
-- controls |
next_state, set_state, set_count, set_hdr, set_tx_start, set_last, |
set_tx_started, set_tx_fin, first_byte_rx |
) |
begin |
-- set output_followers |
udp_tx_int.hdr <= tx_hdr; |
udp_tx_int.data.data_out_last <= set_last; |
udp_tx_start_int <= tx_start_reg; |
|
-- set control signal defaults |
next_state <= IDLE; |
set_state <= '0'; |
set_count <= HOLD; |
set_hdr <= '0'; |
set_tx_start <= HOLD; |
set_last <= '0'; |
set_tx_started <= HOLD; |
set_tx_fin <= HOLD; |
first_byte_rx <= (others => '0'); |
|
-- FSM |
case state is |
|
when IDLE => |
udp_tx_int.data.data_out <= (others => '0'); |
udp_tx_int.data.data_out_valid <= '0'; |
if udp_rx_start_int = '1' or PBTX = '1' then |
if udp_rx_start_int = '1' then |
first_byte_rx <= udp_rx_int.data.data_in; |
else |
first_byte_rx <= x"00"; |
end if; |
set_tx_fin <= CLR; |
set_count <= RST; |
set_hdr <= '1'; |
if udp_rx_int.data.data_in_last = '1' then |
set_tx_started <= SET; |
set_tx_start <= SET; |
next_state <= DATA_OUT; |
set_state <= '1'; |
else |
next_state <= WAIT_RX_DONE; |
set_state <= '1'; |
end if; |
end if; |
|
when WAIT_RX_DONE => |
-- wait until RX pkt fully received |
if udp_rx_int.data.data_in_last = '1' then |
set_tx_started <= SET; |
set_tx_start <= SET; |
next_state <= DATA_OUT; |
set_state <= '1'; |
end if; |
|
when DATA_OUT => |
if udp_tx_result = UDPTX_RESULT_ERR then |
-- have an error from the IP TX layer, clear down the TX |
set_tx_start <= CLR; |
set_tx_fin <= SET; |
set_tx_started <= CLR; |
next_state <= IDLE; |
set_state <= '1'; |
else |
if udp_tx_result = UDPTX_RESULT_SENDING then |
set_tx_start <= CLR; -- reset out start req as soon as we know we are sending |
end if; |
if ip_rx_hdr.is_broadcast = '1' then |
udp_tx_int.data.data_out <= std_logic_vector(count) or x"50"; |
else |
udp_tx_int.data.data_out <= std_logic_vector(count) or x"40"; |
end if; |
udp_tx_int.data.data_out_valid <= udp_tx_data_out_ready_int; |
if udp_tx_data_out_ready_int = '1' then |
if unsigned(count) = x"03" then |
set_last <= '1'; |
set_tx_fin <= SET; |
set_tx_started <= CLR; |
next_state <= IDLE; |
set_state <= '1'; |
else |
set_count <= INCR; |
end if; |
end if; |
end if; |
|
end case; |
end process; |
|
|
|
-- TX response process - SEQ |
tx_proc_sequential: process(clk_int) |
begin |
if rising_edge(clk_int) then |
if reset = '1' then |
-- reset state variables |
state <= IDLE; |
count <= x"00"; |
tx_start_reg <= '0'; |
tx_hdr.dst_ip_addr <= (others => '0'); |
tx_hdr.dst_port <= (others => '0'); |
tx_hdr.src_port <= (others => '0'); |
tx_hdr.data_length <= (others => '0'); |
tx_hdr.checksum <= (others => '0'); |
tx_started_reg <= '0'; |
tx_fin_reg <= '0'; |
PBTX_LED <= '0'; |
else |
PBTX_LED <= PBTX; |
|
-- Next rx_state processing |
if set_state = '1' then |
state <= next_state; |
else |
state <= state; |
end if; |
|
-- count processing |
case set_count is |
when RST => count <= x"00"; |
when INCR => count <= count + 1; |
when HOLD => count <= count; |
end case; |
|
-- set tx hdr |
if set_hdr = '1' then |
-- if the first byte of the rx pkt is 'B' then send to broadcast, otherwise send to reply IP |
if first_byte_rx = x"42" then |
tx_hdr.dst_ip_addr <= IP_BC_ADDR; -- send to Broadcast addr |
elsif first_byte_rx = x"43" then |
tx_hdr.dst_ip_addr <= x"c0bbccdd"; -- set dst unknown so get ARP timeout |
else |
tx_hdr.dst_ip_addr <= udp_rx_int.hdr.src_ip_addr; -- reply to sender |
end if; |
tx_hdr.dst_port <= udp_rx_int.hdr.src_port; |
tx_hdr.src_port <= udp_rx_int.hdr.dst_port; |
tx_hdr.data_length <= x"0004"; |
tx_hdr.checksum <= x"0000"; |
else |
tx_hdr <= tx_hdr; |
end if; |
|
-- set tx start signal |
case set_tx_start is |
when SET => tx_start_reg <= '1'; |
when CLR => tx_start_reg <= '0'; |
when HOLD => tx_start_reg <= tx_start_reg; |
end case; |
|
-- set tx started signal |
case set_tx_started is |
when SET => tx_started_reg <= '1'; |
when CLR => tx_started_reg <= '0'; |
when HOLD => tx_started_reg <= tx_started_reg; |
end case; |
|
-- set tx finished signal |
case set_tx_fin is |
when SET => tx_fin_reg <= '1'; |
when CLR => tx_fin_reg <= '0'; |
when HOLD => tx_fin_reg <= tx_fin_reg; |
end case; |
|
|
end if; |
end if; |
|
end process; |
|
END; |
/arp_tb.vhd
0,0 → 1,601
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 12:35:50 05/31/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/arp1/arp_tb.vhd |
-- Project Name: arp1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: arp |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Revision 0.02 - Added tests for ARP timeout |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
LIBRARY ieee; |
USE ieee.std_logic_1164.ALL; |
USE ieee.numeric_std.ALL; |
use work.arp_types.all; |
|
ENTITY arp_tb IS |
END arp_tb; |
|
ARCHITECTURE behavior OF arp_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT arp |
generic ( |
CLOCK_FREQ : integer := 125000000; -- freq of data_in_clk -- needed to timout cntr |
ARP_TIMEOUT : integer := 60 -- ARP response timeout (s) |
); |
Port ( |
-- lookup request signals |
arp_req_req : in arp_req_req_type; |
arp_req_rslt : out arp_req_rslt_type; |
-- MAC layer RX signals |
data_in_clk : in STD_LOGIC; |
reset : in STD_LOGIC; |
data_in : in STD_LOGIC_VECTOR (7 downto 0); -- ethernet frame (from dst mac addr through to last byte of frame) |
data_in_valid : in STD_LOGIC; -- indicates data_in valid on clock |
data_in_last : in STD_LOGIC; -- indicates last data in frame |
-- MAC layer TX signals |
mac_tx_req : out std_logic; -- indicates that ip wants access to channel (stays up for as long as tx) |
mac_tx_granted : in std_logic; -- indicates that access to channel has been granted |
data_out_clk : in std_logic; |
data_out_ready : in std_logic; -- indicates system ready to consume data |
data_out_valid : out std_logic; -- indicates data out is valid |
data_out_first : out std_logic; -- with data out valid indicates the first byte of a frame |
data_out_last : out std_logic; -- with data out valid indicates the last byte of a frame |
data_out : out std_logic_vector (7 downto 0); -- ethernet frame (from dst mac addr through to last byte of frame) |
-- system signals |
our_mac_address : in STD_LOGIC_VECTOR (47 downto 0); |
our_ip_address : in STD_LOGIC_VECTOR (31 downto 0); |
control : in arp_control_type; |
req_count : out STD_LOGIC_VECTOR(7 downto 0) -- count of arp pkts received |
); |
END COMPONENT; |
|
|
--Inputs |
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal data_in : std_logic_vector(7 downto 0) := (others => '0'); |
signal data_in_valid : std_logic := '0'; |
signal data_in_last : std_logic := '0'; |
signal our_mac_address : std_logic_vector(47 downto 0) := (others => '0'); |
signal our_ip_address : std_logic_vector(31 downto 0) := (others => '0'); |
signal data_out_ready : std_logic; |
signal data_out_valid : std_logic; |
signal data_out_first : std_logic; |
signal data_out_last : std_logic; |
signal data_out : std_logic_vector (7 downto 0); |
signal req_count : STD_LOGIC_VECTOR(7 downto 0); |
signal arp_req_req : arp_req_req_type; |
signal arp_req_rslt : arp_req_rslt_type; |
signal mac_tx_req : std_logic; |
signal mac_tx_granted : std_logic; |
signal control : arp_control_type; |
|
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: arp generic map ( |
CLOCK_FREQ => 10, -- artificially low count to enable pragmatic testing |
ARP_TIMEOUT => 20 |
) |
PORT MAP ( |
-- lookup request mappings |
arp_req_req => arp_req_req, |
arp_req_rslt => arp_req_rslt, |
-- rx mappings |
data_in_clk => clk, |
reset => reset, |
data_in => data_in, |
data_in_valid => data_in_valid, |
data_in_last => data_in_last, |
-- tx mappings |
mac_tx_req => mac_tx_req, |
mac_tx_granted => mac_tx_granted, |
data_out_clk => clk, |
data_out_ready => data_out_ready, |
data_out_valid => data_out_valid, |
data_out_first => data_out_first, |
data_out_last => data_out_last, |
data_out => data_out, |
-- system mappings |
our_mac_address => our_mac_address, |
our_ip_address => our_ip_address, |
control => control, |
req_count => req_count |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '0'; |
wait for clk_period/2; |
clk <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 100 ns; |
|
our_ip_address <= x"c0a80509"; -- 192.168.5.9 |
our_mac_address <= x"002320212223"; |
mac_tx_granted <= '1'; -- FIXME 0 |
control.clear_cache <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
assert mac_tx_req = '0' report "mac_tx_req asserted on reset"; |
|
-- insert stimulus here |
arp_req_req.lookup_req <= '0'; |
arp_req_req.ip <= (others => '0'); |
data_out_ready <= '1'; |
|
report "T1: Send an ARP request: who has 192.168.5.9? Tell 192.168.5.1"; |
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"18"; wait for clk_period; |
data_in <= x"29"; wait for clk_period; |
data_in <= x"26"; wait for clk_period; |
data_in <= x"7c"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Sender MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"18"; wait for clk_period; |
data_in <= x"29"; wait for clk_period; |
data_in <= x"26"; wait for clk_period; |
data_in <= x"7c"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
|
-- check tx arbitration signals |
|
assert mac_tx_req = '1' report "T1: mac_tx_req not set"; |
|
-- ready to tx |
data_out_ready <= '1'; |
mac_tx_granted <= '1'; |
wait for clk_period*10; |
data_out_ready <= '0'; |
wait for clk_period*2; |
data_out_ready <= '1'; |
wait for clk_period*50; |
|
report "T2: Send another ARP request: who has 192.168.5.9? Tell 192.168.5.1, holding off transmitter"; |
data_out_ready <= '0'; |
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"18"; wait for clk_period; |
data_in <= x"29"; wait for clk_period; |
data_in <= x"26"; wait for clk_period; |
data_in <= x"7c"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Sender MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"18"; wait for clk_period; |
data_in <= x"29"; wait for clk_period; |
data_in <= x"26"; wait for clk_period; |
data_in <= x"7c"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
|
-- ready to tx |
wait for clk_period*10; |
data_out_ready <= '1'; |
|
wait for clk_period*50; |
|
report "T3 Send a request for the IP that is already cached"; |
arp_req_req.ip <= x"c0a80501"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T3: should have got mac"; |
assert arp_req_rslt.mac = x"00231829267c" report "T3: incorrect mac"; |
assert arp_req_rslt.got_err = '0' report "T3: should not have got err"; |
arp_req_req.lookup_req <= '0'; |
wait for clk_period; |
wait for clk_period*10; |
|
wait for clk_period*20; |
assert mac_tx_req = '0' report "T3: should not be requesting TX channel"; |
|
report "T4: Request 192.168.5.3 (not cached= and Send an ARP reply: 192.168.5.3 has mac 02:12:03:23:04:54"; |
arp_req_req.ip <= x"c0a80503"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
assert mac_tx_req = '1' report "T4: should be requesting TX channel"; |
wait for clk_period*50; |
-- Send the reply |
data_out_ready <= '1'; |
|
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"12"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"02"; wait for clk_period; |
-- Sender MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"12"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"20"; wait for clk_period; |
data_in <= x"21"; wait for clk_period; |
data_in <= x"22"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T4: should have got mac"; |
assert arp_req_rslt.mac = x"021203230454" report "T4: incorrect mac"; |
assert arp_req_rslt.got_err = '0' report "T4: should not have got err"; |
wait for clk_period*10; |
|
report "T5: Request 192.168.5.4 (not cached), dont send a reply and wait for timeout"; |
arp_req_req.ip <= x"c0a80504"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
assert mac_tx_req = '1' report "T5: should be requesting TX channel"; |
wait for clk_period*200; |
assert arp_req_rslt.got_mac = '0' report "T5: should not have got mac"; |
assert arp_req_rslt.got_err = '1' report "T5: should have got err"; |
|
report "T6: Request 192.168.5.7 (not cached= and Send an ARP reply: 192.168.5.7 has mac 02:15:03:23:04:54"; |
arp_req_req.ip <= x"c0a80507"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '0' report "T6: should not yet have mac"; |
assert arp_req_rslt.got_err = '0' report "T6: should not have got err"; |
|
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
assert mac_tx_req = '1' report "T6: should be requesting TX channel"; |
wait for clk_period*50; |
-- Send the reply |
data_out_ready <= '1'; |
|
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"15"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"02"; wait for clk_period; |
-- Sender MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"15"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"07"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"20"; wait for clk_period; |
data_in <= x"21"; wait for clk_period; |
data_in <= x"22"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T6: should have got mac"; |
assert arp_req_rslt.mac = x"021503230454" report "T6: incorrect mac"; |
assert arp_req_rslt.got_err = '0' report "T6: should not have got err"; |
wait for clk_period*10; |
|
report "T7: Request 192.168.5.7 again an expect it to be in the cache"; |
arp_req_req.ip <= x"c0a80507"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T7: should have mac"; |
assert arp_req_rslt.got_err = '0' report "T7: should not have got err"; |
|
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
|
report "T8: Clear the cache, Request 192.168.5.7 again an expect a 'who has' to be sent"; |
control.clear_cache <= '1'; |
wait for clk_period; |
control.clear_cache <= '0'; |
wait for clk_period; |
|
arp_req_req.ip <= x"c0a80507"; |
arp_req_req.lookup_req <= '1'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '0' report "T8: should not yet have mac"; |
assert arp_req_rslt.got_err = '0' report "T8: should not have got err"; |
|
arp_req_req.lookup_req <= '0'; |
wait for clk_period*20; |
|
|
assert mac_tx_req = '1' report "T8: should be requesting TX channel"; |
wait for clk_period*50; |
-- Send the reply |
data_out_ready <= '1'; |
|
data_in_valid <= '1'; |
-- dst MAC (bc) |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
data_in <= x"ff"; wait for clk_period; |
-- src MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"15"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"04"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"06"; wait for clk_period; |
-- HW type |
data_in <= x"00"; wait for clk_period; |
data_in <= x"01"; wait for clk_period; |
-- Protocol type |
data_in <= x"08"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
-- HW size |
data_in <= x"06"; wait for clk_period; |
-- protocol size |
data_in <= x"04"; wait for clk_period; |
-- Opcode |
data_in <= x"00"; wait for clk_period; |
data_in <= x"02"; wait for clk_period; |
-- Sender MAC |
data_in <= x"02"; wait for clk_period; |
data_in <= x"15"; wait for clk_period; |
data_in <= x"03"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"55"; wait for clk_period; |
data_in <= x"54"; wait for clk_period; |
-- Sender IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"07"; wait for clk_period; |
-- Target MAC |
data_in <= x"00"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
data_in <= x"20"; wait for clk_period; |
data_in <= x"21"; wait for clk_period; |
data_in <= x"22"; wait for clk_period; |
data_in <= x"23"; wait for clk_period; |
-- Target IP |
data_in <= x"c0"; wait for clk_period; |
data_in <= x"a8"; wait for clk_period; |
data_in <= x"05"; wait for clk_period; |
data_in <= x"09"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '1'; |
data_in <= x"00"; wait for clk_period; |
data_in_last <= '0'; |
data_in_valid <= '0'; |
wait for clk_period; |
assert arp_req_rslt.got_mac = '1' report "T8: should have got mac"; |
assert arp_req_rslt.mac = x"021503235554" report "T8: incorrect mac"; |
assert arp_req_rslt.got_err = '0' report "T8: should not have got err"; |
wait for clk_period*10; |
|
report "--- end of tests ---"; |
wait; |
end process; |
|
END; |
/IPv4_RX_tb.vhd
0,0 → 1,391
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 17:32:02 06/03/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/ip1/IPv4_RX_tb.vhd |
-- Project Name: ip1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: IPv4_RX |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
library IEEE; |
use IEEE.STD_LOGIC_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use work.axi.all; |
use work.ipv4_types.all; |
use work.arp_types.all; |
|
|
ENTITY IPv4_RX_tb IS |
END IPv4_RX_tb; |
|
ARCHITECTURE behavior OF IPv4_RX_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT IPv4_RX |
PORT( |
-- IP Layer signals |
ip_rx : out ipv4_rx_type; |
ip_rx_start : out std_logic; -- indicates receipt of ip frame. |
-- system signals |
clk : in STD_LOGIC; -- same clock used to clock mac data and ip data |
reset : in STD_LOGIC; |
our_ip_address : in STD_LOGIC_VECTOR (31 downto 0); |
-- MAC layer RX signals |
mac_data_in : in STD_LOGIC_VECTOR (7 downto 0); -- ethernet frame (from dst mac addr through to last byte of frame) |
mac_data_in_valid : in STD_LOGIC; -- indicates data_in valid on clock |
mac_data_in_last : in STD_LOGIC -- indicates last data in frame |
); |
END COMPONENT; |
|
|
--Inputs |
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal our_ip_address : std_logic_vector(31 downto 0) := (others => '0'); |
signal mac_data_in : std_logic_vector(7 downto 0) := (others => '0'); |
signal mac_data_in_valid : std_logic := '0'; |
signal mac_data_in_last : std_logic := '0'; |
|
--Outputs |
signal ip_rx_start : std_logic; |
signal ip_rx : ipv4_rx_type; |
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: IPv4_RX PORT MAP ( |
ip_rx => ip_rx, |
ip_rx_start => ip_rx_start, |
clk => clk, |
reset => reset, |
our_ip_address => our_ip_address, |
mac_data_in => mac_data_in, |
mac_data_in_valid => mac_data_in_valid, |
mac_data_in_last => mac_data_in_last |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '0'; |
wait for clk_period/2; |
clk <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 100 ns; |
|
our_ip_address <= x"c0a80509"; -- 192.168.5.9 |
mac_data_in_valid <= '0'; |
mac_data_in_last <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
-- check reset conditions |
assert ip_rx_start = '0' report "ip_rx_start not initialised correctly on reset"; |
assert ip_rx.hdr.is_valid = '0' report "ip_rx.hdr.is_valid not initialised correctly on reset"; |
assert ip_rx.hdr.protocol = x"00" report "ip_rx.hdr.protocol not initialised correctly on reset"; |
assert ip_rx.hdr.data_length = x"0000" report "ip_rx.hdr.data_length not initialised correctly on reset"; |
assert ip_rx.hdr.src_ip_addr = x"00000000" report "ip_rx.hdr.src_ip_addr not initialised correctly on reset"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "ip_rx.hdr.num_frame_errors not initialised correctly on reset"; |
assert ip_rx.data.data_in = x"00" report "ip_rx.data.data_in not initialised correctly on reset"; |
assert ip_rx.data.data_in_valid = '0' report "ip_rx.data.data_in_valid not initialised correctly on reset"; |
assert ip_rx.data.data_in_last = '0' report "ip_rx.data.data_in_last not initialised correctly on reset"; |
|
-- insert stimulus here |
|
------------ |
-- TEST 1 -- basic functional rx test with received ip pkt |
------------ |
|
report "T1: Send an eth frame with IP pkt dst ip_address c0a80509, dst mac 002320212223"; |
|
mac_data_in_valid <= '1'; |
-- dst MAC (bc) |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"23"; wait for clk_period; |
mac_data_in <= x"20"; wait for clk_period; |
mac_data_in <= x"21"; wait for clk_period; |
mac_data_in <= x"22"; wait for clk_period; |
mac_data_in <= x"23"; wait for clk_period; |
-- src MAC |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"23"; wait for clk_period; |
mac_data_in <= x"18"; wait for clk_period; |
mac_data_in <= x"29"; wait for clk_period; |
mac_data_in <= x"26"; wait for clk_period; |
mac_data_in <= x"7c"; wait for clk_period; |
-- type |
mac_data_in <= x"08"; wait for clk_period; -- IP pkt |
mac_data_in <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_data_in <= x"45"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- total len |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"18"; wait for clk_period; |
-- ID |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- flags & frag |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- TTL |
mac_data_in <= x"00"; wait for clk_period; |
-- Protocol |
mac_data_in <= x"11"; wait for clk_period; |
-- Header CKS |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- SRC IP |
mac_data_in <= x"c0"; wait for clk_period; |
mac_data_in <= x"a8"; wait for clk_period; |
mac_data_in <= x"05"; wait for clk_period; |
mac_data_in <= x"01"; wait for clk_period; |
-- DST IP |
mac_data_in <= x"c0"; wait for clk_period; |
mac_data_in <= x"a8"; wait for clk_period; |
mac_data_in <= x"05"; wait for clk_period; |
mac_data_in <= x"09"; wait for clk_period; |
|
-- user data |
mac_data_in <= x"24"; wait for clk_period; |
|
assert ip_rx.hdr.is_valid = '1' report "T1: ip_rx.hdr.is_valid not set"; |
assert ip_rx.hdr.protocol = x"11" report "T1: ip_rx.hdr.protocol not set correctly"; |
assert ip_rx.hdr.data_length = x"0004" report "T1: ip_rx.hdr.data_length not set correctly"; |
assert ip_rx.hdr.src_ip_addr = x"c0a80501" report "T1: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T1: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx.hdr.last_error_code = x"0" report "T1: ip_rx.hdr.last_error_code not set correctly"; |
assert ip_rx.hdr.is_broadcast = '0' report "T1: ip_rx.hdr.is_broadcast should not be set"; |
assert ip_rx_start = '1' report "T1: ip_rx_start not set"; |
assert ip_rx.data.data_in_valid = '1' report "T1: ip_rx.data.data_in_valid not set"; |
|
mac_data_in <= x"25"; wait for clk_period; |
mac_data_in <= x"26"; wait for clk_period; |
mac_data_in <= x"27"; mac_data_in_last <= '1';wait for clk_period; |
|
assert ip_rx.data.data_in_last = '1' report "T1: ip_rx.data.data_in_last not set"; |
|
mac_data_in <= x"00"; |
mac_data_in_last <= '0'; |
mac_data_in_valid <= '0'; |
wait for clk_period; |
|
assert ip_rx.data.data_in_valid = '0' report "T1: ip_rx.data.data_in_valid not cleared"; |
assert ip_rx.data.data_in_last = '0' report "T1: ip_rx.data.data_in_last not cleared"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T1: ip_rx.hdr.num_frame_errors non zero at end of test"; |
assert ip_rx.hdr.last_error_code = x"0" report "T1: ip_rx.hdr.last_error_code indicates error at end of test"; |
assert ip_rx_start = '0' report "T1: ip_rx_start not cleared"; |
|
------------ |
-- TEST 2 -- basic functional rx test with received ip pkt that is not for us |
------------ |
|
report "T2: Send an eth frame with IP pkt dst ip_address c0a80507, dst mac 002320212223"; |
|
mac_data_in_valid <= '1'; |
-- dst MAC (bc) |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"23"; wait for clk_period; |
mac_data_in <= x"20"; wait for clk_period; |
mac_data_in <= x"21"; wait for clk_period; |
mac_data_in <= x"22"; wait for clk_period; |
mac_data_in <= x"23"; wait for clk_period; |
|
assert ip_rx.hdr.is_valid = '0' report "T2: ip_rx.hdr.is_valid remains set"; |
|
-- src MAC |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"23"; wait for clk_period; |
mac_data_in <= x"18"; wait for clk_period; |
mac_data_in <= x"29"; wait for clk_period; |
mac_data_in <= x"26"; wait for clk_period; |
mac_data_in <= x"7c"; wait for clk_period; |
-- type |
mac_data_in <= x"08"; wait for clk_period; -- IP pkt |
mac_data_in <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_data_in <= x"45"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- total len |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"18"; wait for clk_period; |
-- ID |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- flags & frag |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- TTL |
mac_data_in <= x"00"; wait for clk_period; |
-- Protocol |
mac_data_in <= x"11"; wait for clk_period; |
-- Header CKS |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- SRC IP |
mac_data_in <= x"c0"; wait for clk_period; |
mac_data_in <= x"a8"; wait for clk_period; |
mac_data_in <= x"05"; wait for clk_period; |
mac_data_in <= x"02"; wait for clk_period; |
-- DST IP |
mac_data_in <= x"c0"; wait for clk_period; |
mac_data_in <= x"a8"; wait for clk_period; |
mac_data_in <= x"05"; wait for clk_period; |
mac_data_in <= x"07"; wait for clk_period; |
|
-- user data |
mac_data_in <= x"24"; wait for clk_period; |
|
assert ip_rx.hdr.is_valid = '1' report "T2: ip_rx.hdr.is_valid not set"; |
assert ip_rx.hdr.protocol = x"11" report "T2: ip_rx.hdr.protocol not set correctly"; |
assert ip_rx.hdr.data_length = x"0004" report "T2: ip_rx.hdr.data_length not set correctly"; |
assert ip_rx.hdr.src_ip_addr = x"c0a80502" report "T2: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T2: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx.hdr.is_broadcast = '0' report "T2: ip_rx.hdr.is_broadcast should not be set"; |
assert ip_rx.hdr.last_error_code = x"0" report "T2: ip_rx.hdr.last_error_code not set correctly"; |
assert ip_rx_start = '0' report "T2: ip_rx_start set when pkt not for us"; |
assert ip_rx.data.data_in_valid = '0' report "T2: ip_rx.data.data_in_valid set when pkt not for us"; |
|
mac_data_in <= x"25"; wait for clk_period; |
mac_data_in <= x"26"; wait for clk_period; |
mac_data_in <= x"27"; mac_data_in_last <= '1';wait for clk_period; |
|
assert ip_rx.data.data_in_last = '0' report "T2: ip_rx.data.data_in_last set"; |
|
mac_data_in <= x"00"; |
mac_data_in_last <= '0'; |
mac_data_in_valid <= '0'; |
wait for clk_period; |
|
assert ip_rx.data.data_in_valid = '0' report "T2: ip_rx.data.data_in_valid not cleared"; |
assert ip_rx.data.data_in_last = '0' report "T2: ip_rx.data.data_in_last not cleared"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T2: ip_rx.hdr.num_frame_errors non zero at end of test"; |
assert ip_rx.hdr.last_error_code = x"0" report "T2: ip_rx.hdr.last_error_code indicates error at end of test"; |
assert ip_rx_start = '0' report "T2: ip_rx_start not cleared"; |
|
wait for clk_period*20; |
|
|
------------ |
-- TEST 3 -- RX Broadcast pkt |
------------ |
|
report "T3: Send an eth frame with IP pkt dst ip_address = BC, dst mac = BC"; |
|
mac_data_in_valid <= '1'; |
-- dst MAC (bc) |
mac_data_in <= x"ff"; wait for clk_period; |
mac_data_in <= x"ff"; wait for clk_period; |
mac_data_in <= x"ff"; wait for clk_period; |
mac_data_in <= x"ff"; wait for clk_period; |
mac_data_in <= x"ff"; wait for clk_period; |
mac_data_in <= x"ff"; wait for clk_period; |
-- src MAC |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"23"; wait for clk_period; |
mac_data_in <= x"18"; wait for clk_period; |
mac_data_in <= x"29"; wait for clk_period; |
mac_data_in <= x"26"; wait for clk_period; |
mac_data_in <= x"7c"; wait for clk_period; |
-- type |
mac_data_in <= x"08"; wait for clk_period; -- IP pkt |
mac_data_in <= x"00"; wait for clk_period; |
-- ver & HL / service type |
mac_data_in <= x"45"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- total len |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"18"; wait for clk_period; |
-- ID |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- flags & frag |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- TTL |
mac_data_in <= x"00"; wait for clk_period; |
-- Protocol |
mac_data_in <= x"11"; wait for clk_period; |
-- Header CKS |
mac_data_in <= x"00"; wait for clk_period; |
mac_data_in <= x"00"; wait for clk_period; |
-- SRC IP |
mac_data_in <= x"c0"; wait for clk_period; |
mac_data_in <= x"a8"; wait for clk_period; |
mac_data_in <= x"05"; wait for clk_period; |
mac_data_in <= x"01"; wait for clk_period; |
-- DST IP |
mac_data_in <= x"ff"; wait for clk_period; |
mac_data_in <= x"ff"; wait for clk_period; |
mac_data_in <= x"ff"; wait for clk_period; |
mac_data_in <= x"ff"; wait for clk_period; |
|
-- user data |
mac_data_in <= x"24"; wait for clk_period; |
|
assert ip_rx.hdr.is_valid = '1' report "T3: ip_rx.hdr.is_valid not set"; |
assert ip_rx.hdr.protocol = x"11" report "T3: ip_rx.hdr.protocol not set correctly"; |
assert ip_rx.hdr.data_length = x"0004" report "T3: ip_rx.hdr.data_length not set correctly"; |
assert ip_rx.hdr.src_ip_addr = x"c0a80501" report "T3: ip_rx.hdr.src_ip_addr not set correctly"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T3: ip_rx.hdr.num_frame_errors not set correctly"; |
assert ip_rx.hdr.is_broadcast = '1' report "T3: ip_rx.hdr.is_broadcast not set"; |
assert ip_rx.hdr.last_error_code = x"0" report "T3: ip_rx.hdr.last_error_code not set correctly"; |
assert ip_rx_start = '1' report "T3: ip_rx_start not set"; |
assert ip_rx.data.data_in_valid = '1' report "T3: ip_rx.data.data_in_valid not set"; |
|
mac_data_in <= x"25"; wait for clk_period; |
mac_data_in <= x"26"; wait for clk_period; |
mac_data_in <= x"27"; mac_data_in_last <= '1';wait for clk_period; |
|
assert ip_rx.data.data_in_last = '1' report "T3: ip_rx.data.data_in_last not set"; |
|
mac_data_in <= x"00"; |
mac_data_in_last <= '0'; |
mac_data_in_valid <= '0'; |
wait for clk_period; |
|
assert ip_rx.data.data_in_valid = '0' report "T3: ip_rx.data.data_in_valid not cleared"; |
assert ip_rx.data.data_in_last = '0' report "T3: ip_rx.data.data_in_last not cleared"; |
assert ip_rx.hdr.num_frame_errors = x"00" report "T3: ip_rx.hdr.num_frame_errors non zero at end of test"; |
assert ip_rx.hdr.last_error_code = x"0" report "T3: ip_rx.hdr.last_error_code indicates error at end of test"; |
assert ip_rx_start = '0' report "T3: ip_rx_start not cleared"; |
|
|
report "--- end of tests ---"; |
|
wait; |
end process; |
|
END; |
/UDP_RX_tb.vhd
0,0 → 1,325
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 16:53:03 06/10/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/ip1/UDP_RX_tb.vhd |
-- Project Name: ip1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: UDP_RX |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
library IEEE; |
use IEEE.STD_LOGIC_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use work.axi.all; |
use work.ipv4_types.all; |
|
ENTITY UDP_RX_tb IS |
END UDP_RX_tb; |
|
ARCHITECTURE behavior OF UDP_RX_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT UDP_RX |
PORT( |
-- UDP Layer signals |
udp_rxo : inout udp_rx_type; |
udp_rx_start : out std_logic; -- indicates receipt of udp header |
-- system signals |
clk : in STD_LOGIC; |
reset : in STD_LOGIC; |
-- IP layer RX signals |
ip_rx_start : in std_logic; -- indicates receipt of ip header |
ip_rx : inout ipv4_rx_type |
); |
END COMPONENT; |
|
|
--Inputs |
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal ip_rx_start : std_logic := '0'; |
|
--BiDirs |
signal udp_rxo : udp_rx_type; |
signal ip_rx : ipv4_rx_type; |
|
--Outputs |
signal udp_rx_start : std_logic; |
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: UDP_RX PORT MAP ( |
udp_rxo => udp_rxo, |
udp_rx_start => udp_rx_start, |
clk => clk, |
reset => reset, |
ip_rx_start => ip_rx_start, |
ip_rx => ip_rx |
); |
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '0'; |
wait for clk_period/2; |
clk <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 100 ns; |
ip_rx_start <= '0'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '0'; |
ip_rx.hdr.protocol <= (others => '0'); |
ip_rx.hdr.num_frame_errors <= (others => '0'); |
ip_rx.hdr.last_error_code <= (others => '0'); |
ip_rx.hdr.is_broadcast <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
reset <= '0'; |
|
-- check reset conditions |
assert udp_rx_start = '0' report "udp_rx_start not initialised correctly on reset"; |
assert udp_rxo.hdr.is_valid = '0' report "udp_rxo.hdr.is_valid not initialised correctly on reset"; |
assert udp_rxo.data.data_in = x"00" report "udp_rxo.data.data_in not initialised correctly on reset"; |
assert udp_rxo.data.data_in_valid = '0' report "udp_rxo.data.data_in_valid not initialised correctly on reset"; |
assert udp_rxo.data.data_in_last = '0' report "udp_rxo.data.data_in_last not initialised correctly on reset"; |
|
-- insert stimulus here |
|
------------ |
-- TEST 1 -- basic functional rx test with received ip pkt |
------------ |
|
report "T1: Send an ip frame with IP src ip_address c0a80501, udp protocol from port x1498 to port x8724 and 3 bytes data"; |
|
ip_rx_start <= '1'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '1'; |
ip_rx.hdr.protocol <= x"11"; -- UDP |
ip_rx.hdr.data_length <= x"000b"; |
ip_rx.hdr.src_ip_addr<= x"c0a80501"; |
wait for clk_period*3; |
-- now send the data |
ip_rx.data.data_in_valid <= '1'; |
ip_rx.data.data_in <= x"14"; wait for clk_period; -- src port |
ip_rx.data.data_in <= x"98"; wait for clk_period; |
ip_rx.data.data_in <= x"87"; wait for clk_period; -- dst port |
ip_rx.data.data_in <= x"24"; wait for clk_period; |
ip_rx.data.data_in <= x"00"; wait for clk_period; -- len (hdr + data) |
ip_rx.data.data_in <= x"0b"; wait for clk_period; |
ip_rx.data.data_in <= x"00"; wait for clk_period; -- mty cks |
ip_rx.data.data_in <= x"00"; wait for clk_period; |
-- udp hdr should be valid |
assert udp_rxo.hdr.is_valid = '1' report "T1: udp_rxo.hdr.is_valid not set"; |
|
ip_rx.data.data_in <= x"41"; wait for clk_period; -- data |
|
assert udp_rxo.hdr.src_ip_addr = x"c0a80501" report "T1: udp_rxo.hdr.src_ip_addr not set correctly"; |
assert udp_rxo.hdr.src_port = x"1498" report "T1: udp_rxo.hdr.src_port not set correctly"; |
assert udp_rxo.hdr.dst_port = x"8724" report "T1: udp_rxo.hdr.dst_port not set correctly"; |
assert udp_rxo.hdr.data_length = x"0003" report "T1: udp_rxo.hdr.data_length not set correctly"; |
assert udp_rx_start = '1' report "T1: udp_rx_start not set"; |
assert udp_rxo.data.data_in_valid = '1' report "T1: udp_rxo.data.data_in_valid not set"; |
|
ip_rx.data.data_in <= x"45"; wait for clk_period; -- data |
ip_rx.data.data_in <= x"49"; ip_rx.data.data_in_last <= '1'; wait for clk_period; |
assert udp_rxo.data.data_in_last = '1' report "T1: udp_rxo.data.data_in_last not set"; |
ip_rx_start <= '0'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '0'; |
wait for clk_period; |
assert udp_rxo.data.data_in = x"00" report "T1: udp_rxo.data.data_in not cleared"; |
assert udp_rxo.data.data_in_valid = '0' report "T1: udp_rxo.data.data_in_valid not cleared"; |
assert udp_rxo.data.data_in_last = '0' report "T1: udp_rxo.data.data_in_last not cleared"; |
|
wait for clk_period; |
|
------------ |
-- TEST 2 -- ability to receive 2nd ip pkt |
------------ |
|
report "T2: Send an ip frame with IP src ip_address c0a80501, udp protocol from port x7623 to port x0365 and 5 bytes data"; |
|
ip_rx_start <= '1'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '1'; |
ip_rx.hdr.protocol <= x"11"; -- UDP |
ip_rx.hdr.data_length <= x"000b"; |
ip_rx.hdr.src_ip_addr<= x"c0a80501"; |
wait for clk_period*3; |
-- now send the data |
ip_rx.data.data_in_valid <= '1'; |
ip_rx.data.data_in <= x"76"; wait for clk_period; -- src port |
ip_rx.data.data_in <= x"23"; wait for clk_period; |
ip_rx.data.data_in <= x"03"; wait for clk_period; -- dst port |
ip_rx.data.data_in <= x"65"; wait for clk_period; |
ip_rx.data.data_in <= x"00"; wait for clk_period; -- len (hdr + data) |
ip_rx.data.data_in <= x"0d"; wait for clk_period; |
ip_rx.data.data_in <= x"00"; wait for clk_period; -- mty cks |
ip_rx.data.data_in <= x"00"; wait for clk_period; |
-- udp hdr should be valid |
assert udp_rxo.hdr.is_valid = '1' report "T2: udp_rxo.hdr.is_valid not set"; |
|
ip_rx.data.data_in <= x"17"; wait for clk_period; -- data |
|
assert udp_rxo.hdr.src_ip_addr = x"c0a80501" report "T2: udp_rxo.hdr.src_ip_addr not set correctly"; |
assert udp_rxo.hdr.src_port = x"7623" report "T2: udp_rxo.hdr.src_port not set correctly"; |
assert udp_rxo.hdr.dst_port = x"0365" report "T2: udp_rxo.hdr.dst_port not set correctly"; |
assert udp_rxo.hdr.data_length = x"0005" report "T2: udp_rxo.hdr.data_length not set correctly"; |
assert udp_rx_start = '1' report "T2: udp_rx_start not set"; |
assert udp_rxo.data.data_in_valid = '1' report "T2: udp_rxo.data.data_in_valid not set"; |
|
ip_rx.data.data_in <= x"37"; wait for clk_period; -- data |
ip_rx.data.data_in <= x"57"; wait for clk_period; -- data |
ip_rx.data.data_in <= x"73"; wait for clk_period; -- data |
ip_rx.data.data_in <= x"f9"; ip_rx.data.data_in_last <= '1'; wait for clk_period; |
assert udp_rxo.data.data_in_last = '1' report "T2: udp_rxo.data.data_in_last not set"; |
ip_rx_start <= '0'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '0'; |
wait for clk_period; |
assert udp_rxo.data.data_in = x"00" report "T2: udp_rxo.data.data_in not cleared"; |
assert udp_rxo.data.data_in_valid = '0' report "T2: udp_rxo.data.data_in_valid not cleared"; |
assert udp_rxo.data.data_in_last = '0' report "T2: udp_rxo.data.data_in_last not cleared"; |
|
------------ |
-- TEST 3 -- ability to reject non-udp protocols |
------------ |
|
report "T3: Send an ip frame with IP src ip_address c0a80501, protocol x12 from port x7623 to port x0365 and 5 bytes data"; |
|
ip_rx_start <= '1'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '1'; |
ip_rx.hdr.protocol <= x"12"; -- non-UDP |
ip_rx.hdr.data_length <= x"000b"; |
ip_rx.hdr.src_ip_addr<= x"c0a80501"; |
wait for clk_period*3; |
-- now send the data |
ip_rx.data.data_in_valid <= '1'; |
ip_rx.data.data_in <= x"76"; wait for clk_period; -- src port |
ip_rx.data.data_in <= x"23"; wait for clk_period; |
ip_rx.data.data_in <= x"03"; wait for clk_period; -- dst port |
ip_rx.data.data_in <= x"65"; wait for clk_period; |
ip_rx.data.data_in <= x"00"; wait for clk_period; -- len (hdr + data) |
ip_rx.data.data_in <= x"0d"; wait for clk_period; |
ip_rx.data.data_in <= x"00"; wait for clk_period; -- mty cks |
ip_rx.data.data_in <= x"00"; wait for clk_period; |
-- udp hdr should be valid |
assert udp_rxo.hdr.is_valid = '0' report "T3: udp_rxo.hdr.is_valid incorrectly set"; |
|
ip_rx.data.data_in <= x"17"; wait for clk_period; -- data |
|
assert udp_rx_start = '0' report "T3: udp_rx_start incorrectly set"; |
assert udp_rxo.data.data_in_valid = '0' report "T3: udp_rxo.data.data_in_valid not set"; |
|
ip_rx.data.data_in <= x"37"; wait for clk_period; -- data |
ip_rx.data.data_in <= x"57"; wait for clk_period; -- data |
ip_rx.data.data_in <= x"73"; wait for clk_period; -- data |
ip_rx.data.data_in <= x"f9"; ip_rx.data.data_in_last <= '1'; wait for clk_period; |
assert udp_rxo.data.data_in_last = '0' report "T3: udp_rxo.data.data_in_last incorrectly set"; |
ip_rx_start <= '0'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '0'; |
wait for clk_period; |
assert udp_rxo.data.data_in = x"00" report "T3: udp_rxo.data.data_in not cleared"; |
assert udp_rxo.data.data_in_valid = '0' report "T3: udp_rxo.data.data_in_valid not cleared"; |
assert udp_rxo.data.data_in_last = '0' report "T3: udp_rxo.data.data_in_last not cleared"; |
|
wait for clk_period; |
|
------------ |
-- TEST 4 -- Ability to receive UDP pkt after non-UDP pkt |
------------ |
|
report "T4: Send an ip frame with IP src ip_address c0a80501, udp protocol from port x1498 to port x8724 and 3 bytes data"; |
|
ip_rx_start <= '1'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '1'; |
ip_rx.hdr.protocol <= x"11"; -- UDP |
ip_rx.hdr.data_length <= x"000b"; |
ip_rx.hdr.src_ip_addr<= x"c0a80501"; |
wait for clk_period*3; |
-- now send the data |
ip_rx.data.data_in_valid <= '1'; |
ip_rx.data.data_in <= x"14"; wait for clk_period; -- src port |
ip_rx.data.data_in <= x"98"; wait for clk_period; |
ip_rx.data.data_in <= x"87"; wait for clk_period; -- dst port |
ip_rx.data.data_in <= x"24"; wait for clk_period; |
ip_rx.data.data_in <= x"00"; wait for clk_period; -- len (hdr + data) |
ip_rx.data.data_in <= x"0b"; wait for clk_period; |
ip_rx.data.data_in <= x"00"; wait for clk_period; -- mty cks |
ip_rx.data.data_in <= x"00"; wait for clk_period; |
-- udp hdr should be valid |
assert udp_rxo.hdr.is_valid = '1' report "T4: udp_rxo.hdr.is_valid not set"; |
|
ip_rx.data.data_in <= x"41"; wait for clk_period; -- data |
|
assert udp_rxo.hdr.src_ip_addr = x"c0a80501" report "T4: udp_rxo.hdr.src_ip_addr not set correctly"; |
assert udp_rxo.hdr.src_port = x"1498" report "T4: udp_rxo.hdr.src_port not set correctly"; |
assert udp_rxo.hdr.dst_port = x"8724" report "T4: udp_rxo.hdr.dst_port not set correctly"; |
assert udp_rxo.hdr.data_length = x"0003" report "T4: udp_rxo.hdr.data_length not set correctly"; |
assert udp_rx_start = '1' report "T4: udp_rx_start not set"; |
assert udp_rxo.data.data_in_valid = '1' report "T4: udp_rxo.data.data_in_valid not set"; |
|
ip_rx.data.data_in <= x"45"; wait for clk_period; -- data |
ip_rx.data.data_in <= x"49"; ip_rx.data.data_in_last <= '1'; wait for clk_period; |
assert udp_rxo.data.data_in_last = '1' report "T4: udp_rxo.data.data_in_last not set"; |
ip_rx_start <= '0'; |
ip_rx.data.data_in_valid <= '0'; |
ip_rx.data.data_in_last <= '0'; |
ip_rx.hdr.is_valid <= '0'; |
wait for clk_period; |
assert udp_rxo.data.data_in = x"00" report "T4: udp_rxo.data.data_in not cleared"; |
assert udp_rxo.data.data_in_valid = '0' report "T4: udp_rxo.data.data_in_valid not cleared"; |
assert udp_rxo.data.data_in_last = '0' report "T4: udp_rxo.data.data_in_last not cleared"; |
|
wait for clk_period; |
|
report "--- end of tests ---"; |
|
wait; |
end process; |
|
END; |
/UDP_TX_tb.vhd
0,0 → 1,219
-------------------------------------------------------------------------------- |
-- Company: |
-- Engineer: |
-- |
-- Create Date: 18:43:49 06/10/2011 |
-- Design Name: |
-- Module Name: C:/Users/pjf/Documents/projects/fpga/xilinx/Network/ip1/UDP_TX_tb.vhd |
-- Project Name: ip1 |
-- Target Device: |
-- Tool versions: |
-- Description: |
-- |
-- VHDL Test Bench Created by ISE for module: UDP_TX |
-- |
-- Dependencies: |
-- |
-- Revision: |
-- Revision 0.01 - File Created |
-- Additional Comments: |
-- |
-- Notes: |
-- This testbench has been automatically generated using types std_logic and |
-- std_logic_vector for the ports of the unit under test. Xilinx recommends |
-- that these types always be used for the top-level I/O of a design in order |
-- to guarantee that the testbench will bind correctly to the post-implementation |
-- simulation model. |
-------------------------------------------------------------------------------- |
library IEEE; |
use IEEE.STD_LOGIC_1164.ALL; |
use IEEE.NUMERIC_STD.ALL; |
use work.axi.all; |
use work.ipv4_types.all; |
|
ENTITY UDP_TX_tb IS |
END UDP_TX_tb; |
|
ARCHITECTURE behavior OF UDP_TX_tb IS |
|
-- Component Declaration for the Unit Under Test (UUT) |
|
COMPONENT UDP_TX |
PORT( |
-- UDP Layer signals |
udp_tx_start : in std_logic; -- indicates req to tx UDP |
udp_txi : in udp_tx_type; -- UDP tx cxns |
udp_tx_result : out std_logic_vector (1 downto 0);-- tx status (changes during transmission) |
udp_tx_data_out_ready: out std_logic; -- indicates udp_tx is ready to take data |
-- system signals |
clk : in STD_LOGIC; -- same clock used to clock mac data and ip data |
reset : in STD_LOGIC; |
-- IP layer TX signals |
ip_tx_start : out std_logic; |
ip_tx : out ipv4_tx_type; -- IP tx cxns |
ip_tx_result : in std_logic_vector (1 downto 0); -- tx status (changes during transmission) |
ip_tx_data_out_ready : in std_logic -- indicates IP TX is ready to take data |
); |
END COMPONENT; |
|
|
--Inputs |
signal udp_tx_start : std_logic := '0'; |
signal clk : std_logic := '0'; |
signal reset : std_logic := '0'; |
signal udp_txi : udp_tx_type; |
signal ip_tx_result : std_logic_vector (1 downto 0); -- tx status (changes during transmission) |
signal ip_tx_data_out_ready : std_logic; -- indicates IP TX is ready to take data |
|
--Outputs |
signal ip_tx_start : std_logic := '0'; |
signal ip_tx : ipv4_tx_type; |
signal udp_tx_result : std_logic_vector (1 downto 0); |
signal udp_tx_data_out_ready : std_logic; |
|
-- Clock period definitions |
constant clk_period : time := 8 ns; |
|
BEGIN |
|
-- Instantiate the Unit Under Test (UUT) |
uut: UDP_TX PORT MAP ( |
udp_tx_start => udp_tx_start, |
udp_txi => udp_txi, |
udp_tx_result => udp_tx_result, |
udp_tx_data_out_ready => udp_tx_data_out_ready, |
clk => clk, |
reset => reset, |
ip_tx_start => ip_tx_start, |
ip_tx => ip_tx, |
ip_tx_result => ip_tx_result, |
ip_tx_data_out_ready => ip_tx_data_out_ready |
); |
|
|
-- Clock process definitions |
clk_process :process |
begin |
clk <= '0'; |
wait for clk_period/2; |
clk <= '1'; |
wait for clk_period/2; |
end process; |
|
|
-- Stimulus process |
stim_proc: process |
begin |
-- hold reset state for 100 ns. |
wait for 100 ns; |
|
udp_tx_start <= '0'; |
|
udp_txi.hdr.dst_ip_addr <= (others => '0'); |
udp_txi.hdr.dst_port <= (others => '0'); |
udp_txi.hdr.src_port <= (others => '0'); |
udp_txi.hdr.data_length <= (others => '0'); |
udp_txi.hdr.checksum <= (others => '0'); |
udp_txi.data.data_out_last <= '0'; |
|
reset <= '1'; |
wait for clk_period*10; |
reset <= '0'; |
wait for clk_period*5; |
|
-- check reset conditions |
|
assert ip_tx_start = '0' report "ip_tx_start not initialised correctly on reset"; |
assert ip_tx.data.data_out_valid = '0' report "ip_tx.data.data_out_valid not initialised correctly on reset"; |
assert ip_tx.data.data_out_last = '0' report "ip_tx.data.data_out_last not initialised correctly on reset"; |
assert udp_tx_result = UDPTX_RESULT_NONE report "udp_tx_result not initialised correctly on reset"; |
|
-- insert stimulus here |
|
wait for clk_period*5; |
|
------------ |
-- TEST 1 -- basic functional tx test |
------------ |
|
report "T1: basic functional tx test - send 56, 57, 58 to port 8532"; |
|
udp_txi.hdr.dst_ip_addr <= x"c0123478"; |
udp_txi.hdr.dst_port <= x"1467"; |
udp_txi.hdr.src_port <= x"8532"; |
udp_txi.hdr.data_length <= x"0003"; |
|
udp_tx_start <= '1'; |
ip_tx_data_out_ready <= '1'; -- IP layer can accept data |
wait for clk_period; |
udp_tx_start <= '0'; wait for clk_period; |
ip_tx_result <= IPTX_RESULT_NONE; |
|
assert udp_tx_result = UDPTX_RESULT_SENDING report "T1: result should be UDPTX_RESULT_SENDING"; |
|
wait until udp_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
udp_txi.data.data_out_valid <= '1'; |
udp_txi.data.data_out <= x"56"; wait for clk_period; |
udp_txi.data.data_out <= x"57"; wait for clk_period; |
|
udp_txi.data.data_out <= x"58"; |
udp_txi.data.data_out_last <= '1'; |
wait for clk_period; |
|
assert ip_tx.data.data_out_last = '1' report "T1: ip_tx.datda_out_last not set on last byte"; |
|
udp_txi.data.data_out_valid <= '0'; |
udp_txi.data.data_out_last <= '0'; |
wait for clk_period*2; |
ip_tx_result <= IPTX_RESULT_SENT; |
|
assert udp_tx_result = UDPTX_RESULT_SENT report "T1: result should be UDPTX_RESULT_SENT"; |
wait for clk_period*2; |
|
------------ |
-- TEST 2 -- 2nd pkt |
------------ |
|
report "T2: send a second pkt - 56,57,58,59 to port 8532"; |
|
udp_txi.hdr.dst_ip_addr <= x"c0123475"; |
udp_txi.hdr.dst_port <= x"1467"; |
udp_txi.hdr.src_port <= x"8532"; |
udp_txi.hdr.data_length <= x"0005"; |
|
udp_tx_start <= '1'; |
ip_tx_data_out_ready <= '1'; -- IP layer can accept data |
wait for clk_period; |
udp_tx_start <= '0'; wait for clk_period; |
|
assert udp_tx_result = UDPTX_RESULT_SENDING report "T1: result should be UDPTX_RESULT_SENDING"; |
|
wait until udp_tx_data_out_ready = '1'; |
|
-- start to tx IP data |
udp_txi.data.data_out_valid <= '1'; |
udp_txi.data.data_out <= x"56"; wait for clk_period; |
udp_txi.data.data_out <= x"57"; wait for clk_period; |
udp_txi.data.data_out <= x"58"; wait for clk_period; |
udp_txi.data.data_out <= x"59"; wait for clk_period; |
|
udp_txi.data.data_out <= x"5a"; |
udp_txi.data.data_out_last <= '1'; |
wait for clk_period; |
assert ip_tx.data.data_out_last = '1' report "T1: ip_tx.datda_out_last not set on last byte"; |
|
udp_txi.data.data_out_valid <= '0'; |
udp_txi.data.data_out_last <= '0'; |
wait for clk_period*2; |
|
assert udp_tx_result = UDPTX_RESULT_SENT report "T1: result should be UDPTX_RESULT_SENT"; |
wait for clk_period*2; |
|
report "--- end of tests ---"; |
|
wait; |
end process; |
|
END; |