URL
https://opencores.org/ocsvn/udp_ip_stack/udp_ip_stack/trunk
Subversion Repositories udp_ip_stack
Compare Revisions
- This comparison shows the changes necessary to convert path
/udp_ip_stack
- from Rev 12 to Rev 13
- ↔ Reverse comparison
Rev 12 → Rev 13
/trunk/rtl/vhdl/ipcores/xilinx/emac1.xco
0,0 → 1,92
############################################################## |
# |
# Xilinx Core Generator version 13.2 |
# Date: Sat Jul 23 13:38:01 2011 |
# |
############################################################## |
# |
# This file contains the customisation parameters for a |
# Xilinx CORE Generator IP GUI. It is strongly recommended |
# that you do not manually alter this file as it may cause |
# unexpected and unsupported behavior. |
# |
############################################################## |
# |
# Generated from component: xilinx.com:ip:v6_emac:2.1 |
# |
############################################################## |
# |
# BEGIN Project Options |
SET addpads = false |
SET asysymbol = true |
SET busformat = BusFormatAngleBracketNotRipped |
SET createndf = false |
SET designentry = VHDL |
SET device = xc6vlx240t |
SET devicefamily = virtex6 |
SET flowvendor = Other |
SET formalverification = false |
SET foundationsym = false |
SET implementationfiletype = Ngc |
SET package = ff1156 |
SET removerpms = false |
SET simulationfiles = Behavioral |
SET speedgrade = -1 |
SET verilogsim = false |
SET vhdlsim = true |
# END Project Options |
# BEGIN Select |
SELECT Virtex-6_Embedded_Tri-Mode_Ethernet_MAC_Wrapper family Xilinx,_Inc. 2.1 |
# END Select |
# BEGIN Parameters |
CSET address_filter=false |
CSET address_filter_enable=false |
CSET axi_ipif=true |
CSET client_side_data_width=8_bit |
CSET clock_enable=true |
CSET component_name=emac1 |
CSET management_interface=false |
CSET mdio=false |
CSET number_of_address_table_entries=0 |
CSET phy_an_enable=false |
CSET phy_ignore_adzero=false |
CSET phy_isolate=false |
CSET phy_link_timer_value=13D |
CSET phy_loopback_in_gtp=false |
CSET phy_loopback_msb=false |
CSET phy_powerdown=false |
CSET phy_reset=false |
CSET phy_unidirection_enable=false |
CSET physical_interface=GMII |
CSET rx_ctrl_lencheck_disable=false |
CSET rx_disable_length=false |
CSET rx_enable=true |
CSET rx_flow_control_enable=false |
CSET rx_half_duplex_enable=false |
CSET rx_in_band_fcs_enable=false |
CSET rx_jumbo_frame_enable=false |
CSET rx_reset=false |
CSET rx_vlan_enable=false |
CSET serial_mode_switch_enable=false |
CSET sgmii_mode=No_clock |
CSET speed=1000_Mbps |
CSET statistics_counters=false |
CSET statistics_reset=true |
CSET statistics_width=32bit |
CSET tx_enable=true |
CSET tx_flow_control_enable=false |
CSET tx_half_duplex_enable=false |
CSET tx_ifg_adjust_enable=false |
CSET tx_in_band_fcs_enable=false |
CSET tx_jumbo_frame_enable=false |
CSET tx_reset=false |
CSET tx_vlan_enable=false |
CSET unicast_pause_mac_address_1=AA |
CSET unicast_pause_mac_address_2=BB |
CSET unicast_pause_mac_address_3=CC |
CSET unicast_pause_mac_address_4=DD |
CSET unicast_pause_mac_address_5=EE |
CSET unicast_pause_mac_address_6=FF |
# END Parameters |
GENERATE |
# CRC: fd590560 |