URL
https://opencores.org/ocsvn/usb_sniffer/usb_sniffer/trunk
Subversion Repositories usb_sniffer
Compare Revisions
- This comparison shows the changes necessary to convert path
/usb_sniffer/trunk
- from Rev 1 to Rev 2
- ↔ Reverse comparison
Rev 1 → Rev 2
/README.md
0,0 → 1,84
### USB Sniffer |
|
Github: [https://github.com/ultraembedded/core_usb_sniffer](https://github.com/ultraembedded/core_usb_sniffer) |
|
This core is a HS/FS USB2.0 analyzer (USB bus sniffer). |
The core monitors a UTMI interface and logs the traffic seen to a memory buffer via an AXI-4 bus master interface. |
The log format can be extracted continuously (continuous capture mode) or the core can stop capturing when the memory buffer is full (one-shot mode). |
|
Configuration of the IP is performed using an AXI4-Lite slave interface. |
|
This core has been used to produce a [USB 2.0 Capture Device](https://github.com/ultraembedded/usb2sniffer). |
|
#### Features |
|
* Option of filtering based on device ID and/or endpoint. |
* Option of filtering out SOF packets. |
* Option of filtering out IN+NAK packets. |
* Dense logging format. |
* Supports continuous streaming or one-shot mode. |
* Detection of buffer overruns. |
|
##### Register Map |
|
| Offset | Name | Description | |
| ------ | ---- | ------------- | |
| 0x00 | USB_BUFFER_CFG | [RW] Configuration Register | |
| 0x04 | USB_BUFFER_STS | [R] Status Register | |
| 0x08 | USB_BUFFER_BASE | [RW] Buffer Base Address | |
| 0x0c | USB_BUFFER_END | [RW] Buffer End Address | |
| 0x10 | USB_BUFFER_CURRENT | [R] Buffer Current address | |
|
##### Register: USB_BUFFER_CFG |
|
| Bits | Name | Description | |
| ---- | ---- | -------------- | |
| 31 | CONT | Continuous capture - overwrite on wrap (0 = Stop on full, 1 = cont) | |
| 30:24 | DEV | Device ID to match (only if MATCH_DEV = 1) | |
| 19:16 | EP | Endpoint to match (only if MATCH_EP = 1) | |
| 15 | PHY_DMPULLDOWN | UTMI PHY D+ Pulldown Enable (valid if SPEED=manual) | |
| 14 | PHY_DPPULLDOWN | UTMI PHY D+ Pulldown Enable (valid if SPEED=manual) | |
| 13 | PHY_TERMSELECT | UTMI PHY Termination Select (valid if SPEED=manual) | |
| 12:11 | PHY_XCVRSELECT | UTMI PHY Transceiver Select (valid if SPEED=manual) | |
| 10:9 | PHY_OPMODE | UTMI PHY Output Mode (valid if SPEED=manual) | |
| 8:7 | SPEED | USB bus speed (0 = HS, 1 = FS, 2 = LS, 3=manual) | |
| 6 | EXCLUDE_EP | Exclude specific endpoint | |
| 5 | MATCH_EP | Match specific endpoint | |
| 4 | EXCLUDE_DEV | Exclude specific device ID | |
| 3 | MATCH_DEV | Match specific device ID | |
| 2 | IGNORE_SOF | Drop SOF packets (0 = Log SOF, 1 = Drop SOF) | |
| 1 | IGNORE_IN_NAK | Drop IN + NAK sequences | |
| 0 | ENABLED | Capture enabled | |
|
##### Register: USB_BUFFER_STS |
|
| Bits | Name | Description | |
| ---- | ---- | -------------- | |
| 2 | DATA_LOSS | Data lost due to stream backpressure | |
| 1 | WRAPPED | Capture wrapped | |
| 0 | TRIG | Capture triggered | |
|
##### Register: USB_BUFFER_BASE |
|
| Bits | Name | Description | |
| ---- | ---- | -------------- | |
| 31:0 | ADDR | Address of buffer base | |
|
##### Register: USB_BUFFER_END |
|
| Bits | Name | Description | |
| ---- | ---- | -------------- | |
| 31:0 | ADDR | Address of buffer end | |
|
##### Register: USB_BUFFER_CURRENT |
|
| Bits | Name | Description | |
| ---- | ---- | -------------- | |
| 31:0 | ADDR | Current buffer address - last entry written | |
|
#### References |
|
* [UTMI+ Low Pin Interface (ULPI) Specification](https://www.sparkfun.com/datasheets/Components/SMD/ULPI_v1_1.pdf) |
* [SMSC USB3300 USB PHY Datasheet](http://ww1.microchip.com/downloads/en/DeviceDoc/3300db.pdf) |
* [ULPI Wrapper](https://github.com/ultraembedded/core_ulpi_wrapper) |
|