OpenCores
URL https://opencores.org/ocsvn/usb_sniffer/usb_sniffer/trunk

Subversion Repositories usb_sniffer

Compare Revisions

  • This comparison shows the changes necessary to convert path
    /usb_sniffer/trunk
    from Rev 1 to Rev 2
    Reverse comparison

Rev 1 → Rev 2

/README.md
0,0 → 1,84
### USB Sniffer
 
Github: [https://github.com/ultraembedded/core_usb_sniffer](https://github.com/ultraembedded/core_usb_sniffer)
 
This core is a HS/FS USB2.0 analyzer (USB bus sniffer).
The core monitors a UTMI interface and logs the traffic seen to a memory buffer via an AXI-4 bus master interface.
The log format can be extracted continuously (continuous capture mode) or the core can stop capturing when the memory buffer is full (one-shot mode).
 
Configuration of the IP is performed using an AXI4-Lite slave interface.
 
This core has been used to produce a [USB 2.0 Capture Device](https://github.com/ultraembedded/usb2sniffer).
 
#### Features
 
* Option of filtering based on device ID and/or endpoint.
* Option of filtering out SOF packets.
* Option of filtering out IN+NAK packets.
* Dense logging format.
* Supports continuous streaming or one-shot mode.
* Detection of buffer overruns.
 
##### Register Map
 
| Offset | Name | Description |
| ------ | ---- | ------------- |
| 0x00 | USB_BUFFER_CFG | [RW] Configuration Register |
| 0x04 | USB_BUFFER_STS | [R] Status Register |
| 0x08 | USB_BUFFER_BASE | [RW] Buffer Base Address |
| 0x0c | USB_BUFFER_END | [RW] Buffer End Address |
| 0x10 | USB_BUFFER_CURRENT | [R] Buffer Current address |
 
##### Register: USB_BUFFER_CFG
 
| Bits | Name | Description |
| ---- | ---- | -------------- |
| 31 | CONT | Continuous capture - overwrite on wrap (0 = Stop on full, 1 = cont) |
| 30:24 | DEV | Device ID to match (only if MATCH_DEV = 1) |
| 19:16 | EP | Endpoint to match (only if MATCH_EP = 1) |
| 15 | PHY_DMPULLDOWN | UTMI PHY D+ Pulldown Enable (valid if SPEED=manual) |
| 14 | PHY_DPPULLDOWN | UTMI PHY D+ Pulldown Enable (valid if SPEED=manual) |
| 13 | PHY_TERMSELECT | UTMI PHY Termination Select (valid if SPEED=manual) |
| 12:11 | PHY_XCVRSELECT | UTMI PHY Transceiver Select (valid if SPEED=manual) |
| 10:9 | PHY_OPMODE | UTMI PHY Output Mode (valid if SPEED=manual) |
| 8:7 | SPEED | USB bus speed (0 = HS, 1 = FS, 2 = LS, 3=manual) |
| 6 | EXCLUDE_EP | Exclude specific endpoint |
| 5 | MATCH_EP | Match specific endpoint |
| 4 | EXCLUDE_DEV | Exclude specific device ID |
| 3 | MATCH_DEV | Match specific device ID |
| 2 | IGNORE_SOF | Drop SOF packets (0 = Log SOF, 1 = Drop SOF) |
| 1 | IGNORE_IN_NAK | Drop IN + NAK sequences |
| 0 | ENABLED | Capture enabled |
 
##### Register: USB_BUFFER_STS
 
| Bits | Name | Description |
| ---- | ---- | -------------- |
| 2 | DATA_LOSS | Data lost due to stream backpressure |
| 1 | WRAPPED | Capture wrapped |
| 0 | TRIG | Capture triggered |
 
##### Register: USB_BUFFER_BASE
 
| Bits | Name | Description |
| ---- | ---- | -------------- |
| 31:0 | ADDR | Address of buffer base |
 
##### Register: USB_BUFFER_END
 
| Bits | Name | Description |
| ---- | ---- | -------------- |
| 31:0 | ADDR | Address of buffer end |
 
##### Register: USB_BUFFER_CURRENT
 
| Bits | Name | Description |
| ---- | ---- | -------------- |
| 31:0 | ADDR | Current buffer address - last entry written |
 
#### References
 
* [UTMI+ Low Pin Interface (ULPI) Specification](https://www.sparkfun.com/datasheets/Components/SMD/ULPI_v1_1.pdf)
* [SMSC USB3300 USB PHY Datasheet](http://ww1.microchip.com/downloads/en/DeviceDoc/3300db.pdf)
* [ULPI Wrapper](https://github.com/ultraembedded/core_ulpi_wrapper)
 

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.