URL
https://opencores.org/ocsvn/minsoc/minsoc/trunk
Subversion Repositories minsoc
Compare Revisions
- This comparison shows the changes necessary to convert path
/minsoc/trunk/syn
- from Rev 95 to Rev 93
- ↔ Reverse comparison
Rev 95 → Rev 93
/altera/minsoc_top.qsf
File deleted
/altera/Makefile
9,7 → 9,7
ETH_RTL = ${MINSOC_RTL}/ethmac/rtl/verilog |
BUILD_SUPPORT = $(MINSOC)/syn/buildSupport |
PROJECT_DIR = $(MINSOC)/prj/altera |
QSF_FILE = $(BUILD_SUPPORT)/minsoc_top |
|
help: |
@echo " all: Synthesize and implement the SoC, then generate a bit stream" |
@echo "" |
18,43 → 18,38
@echo " fit: Place the target hardware, then route the wires" |
@echo " sta: Perfom a timming analysis" |
@echo " eda: Generate a netlist of the hardware" |
@echo " config: Load the bitstream into the device using ALTERA USB Blaster and JTAG configuration" |
@echo "" |
@echo " clean: Delete all superfluous files generated by Altera tools" |
@echo " distclean: Delete all generated files" |
|
all: bitgen eda sta |
map: $(BUILD_SUPPORT)/minsoc_top.map.summary |
fit: $(BUILD_SUPPORT)/minsoc_top.fit.summary |
map: minsoc_top.map.summary |
fit: minsoc_top.fit.summary |
bitgen: minsoc_top.sof |
eda: $(BUILD_SUPPORT)/minsoc_top.eda.summary |
sta: $(BUILD_SUPPORT)/minsoc_top.sta.summary |
eda: minsoc_top.eda.summary |
sta: minsoc_top.sta.summary |
|
#minsoc_top.map.summary: ${MINSOC_RTL}/*.v $(UART_RTL)/*.v $(ADV_DEBUG_ROOT)/*.v $(DEBUG_RTL)/*.v $(OR1200_RTL)/*.v $(ETH_RTL)/*.v ${MINSOC_DEFINES}/minsoc_defines.v minsoc_top.qsf |
$(BUILD_SUPPORT)/minsoc_top.map.summary: ${MINSOC_DEFINES}/minsoc_defines.v $(BUILD_SUPPORT)/minsoc_top.qsf |
minsoc_top.map.summary: ${MINSOC_DEFINES}/minsoc_defines.v minsoc_top.qsf |
|
quartus_map $(QSF_FILE) --write_settings_files=off |
quartus_map minsoc_top --write_settings_files=off |
|
$(BUILD_SUPPORT)/minsoc_top.fit.summary: $(BUILD_SUPPORT)/minsoc_top.map.summary |
quartus_fit $(QSF_FILE) --write_Settings_files=off --pack_register=minimize_area |
minsoc_top.fit.summary: minsoc_top.map.summary |
quartus_fit minsoc_top --write_Settings_files=off --pack_register=minimize_area |
|
minsoc_top.sof: $(BUILD_SUPPORT)/minsoc_top.fit.summary |
quartus_asm $(QSF_FILE) |
mv $(BUILD_SUPPORT)/*.sof . |
minsoc_top.sof: minsoc_top.fit.summary |
quartus_asm minsoc_top |
|
$(BUILD_SUPPORT)/minsoc_top.sta.summary: $(BUILD_SUPPORT)/minsoc_top.fit.summary |
quartus_sta $(QSF_FILE) |
minsoc_top.sta.summary: minsoc_top.fit.summary |
quartus_sta minsoc_top |
|
$(BUILD_SUPPORT)/minsoc_top.eda.summary: $(BUILD_SUPPORT)/minsoc_top.fit.summary |
quartus_eda $(QSF_FILE) --write_settings_files=off |
minsoc_top.eda.summary: minsoc_top.fit.summary |
quartus_eda minsoc_top --write_settings_files=off |
|
config: minsoc_top.sof |
quartus_pgm -c USB-Blaster -m jtag -o "p;minsoc_top.sof" |
|
distclean: |
$(RM) *.sof |
make clean |
|
clean: |
$(RM) $(BUILD_SUPPORT)/*.rpt $(BUILD_SUPPORT)/*.summary $(BUILD_SUPPORT)/*.jdi $(BUILD_SUPPORT)/*.smsg $(BUILD_SUPPORT)/*.pin $(BUILD_SUPPORT)/*.qpf |
$(RM) -r $(BUILD_SUPPORT)/db $(BUILD_SUPPORT)/incremental_db |
$(RM) *.rpt *.summary *.jdi *.smsg *.pin *.qpf |
rm -fr db incremental_db |