URL
https://opencores.org/ocsvn/minsoc/minsoc/trunk
Subversion Repositories minsoc
Compare Revisions
- This comparison shows the changes necessary to convert path
/minsoc
- from Rev 62 to Rev 61
- ↔ Reverse comparison
Rev 62 → Rev 61
/trunk/rtl/verilog/xilinx_dcm.v
File deleted
/trunk/rtl/verilog/altera_pll.v
File deleted
/trunk/rtl/verilog/minsoc_clock_manager.v
29,30 → 29,259
end |
end |
assign clk_o = clk_int; |
`elsif FPGA_CLOCK_DIVISION |
|
`elsif FPGA_CLOCK_DIVISION |
`ifdef ALTERA_FPGA |
altera_pll # |
( |
.FREQ_DIV(divisor) |
) |
minsoc_altera_pll |
( |
.inclk0(clk_i), |
.c0(clk_o) |
); |
`ifdef ALTERA_FPGA |
`ifdef ARRIA_GX |
defparam systemPll.FAMILY = "Arria GX"; |
`elsif ARRIA_II_GX |
defparam systemPll.FAMILY = "Arria II GX"; |
`elsif CYCLONE_I |
defparam systemPll.FAMILY = "Cyclone I"; |
`elsif CYCLONE_II |
defparam systemPll.FAMILY = "Cyclone II"; |
`elsif CYCLONE_III |
defparam systemPll.FAMILY = "Cyclone III"; |
`elsif CYCLONE_III_LS |
defparam systemPll.FAMILY = "Cyclone III LS"; |
`elsif CYCLONE_IV_E |
defparam systemPll.FAMILY = "Cyclone IV E"; |
`elsif CYCLONE_IV_GS |
defparam systemPll.FAMILY = "Cyclone IV GS"; |
`elsif MAX_II |
defparam systemPll.FAMILY = "MAX II"; |
`elsif MAX_V |
defparam systemPll.FAMILY = "MAX V"; |
`elsif MAX3000A |
defparam systemPll.FAMILY = "MAX3000A"; |
`elsif MAX7000AE |
defparam systemPll.FAMILY = "MAX7000AE"; |
`elsif MAX7000B |
defparam systemPll.FAMILY = "MAX7000B"; |
`elsif MAX7000S |
defparam systemPll.FAMILY = "MAX7000S"; |
`elsif STRATIX |
defparam systemPll.FAMILY = "Stratix"; |
`elsif STRATIX_II |
defapram systemPll.FAMILY = "Stratix II"; |
`elsif STRATIX_II_GX |
defparam systemPll.FAMILY = "Stratix II GX"; |
`elsif STRATIX_III |
defparam systemPll.FAMILY = "Stratix III" |
`endif |
|
defparam systemPll.FREQ_DIV = divisor; |
|
minsoc_pll systemPll |
( |
.inclk0(clk_i), |
.c0(clk_o) |
); |
|
`elsif XILINX_FPGA |
xilinx_dcm # |
( |
.divisor(divisor) |
) |
minsoc_xilinx_dcm |
( |
.clk_i(clk_i), |
.clk_o(clk_o) |
|
`ifdef SPARTAN2 |
`define MINSOC_DLL |
`elsif VIRTEX |
`define MINSOC_DLL |
`endif // !SPARTAN2/VIRTEX |
|
`ifdef SPARTAN3 |
`define MINSOC_DCM |
`elsif VIRTEX2 |
`define MINSOC_DCM |
`endif // !SPARTAN3/VIRTEX2 |
|
`ifdef SPARTAN3E |
`define MINSOC_DCM_SP |
`elsif SPARTAN3A |
`define MINSOC_DCM_SP |
`endif // !SPARTAN3E/SPARTAN3A |
|
`ifdef VIRTEX4 |
`define MINSOC_DCM_ADV |
`define MINSOC_DCM_COMPONENT "VIRTEX4" |
`elsif VIRTEX5 |
`define MINSOC_DCM_ADV |
`define MINSOC_DCM_COMPONENT "VIRTEX5" |
`endif // !VIRTEX4/VIRTEX5 |
|
wire CLKIN_IN; |
wire CLKDV_OUT; |
|
assign CLKIN_IN = clk_i; |
assign clk_o = CLKDV_OUT; |
|
wire CLKIN_IBUFG; |
wire CLK0_BUF; |
wire CLKFB_IN; |
wire CLKDV_BUF; |
|
IBUFG CLKIN_IBUFG_INST ( |
.I(CLKIN_IN), |
.O(CLKIN_IBUFG) |
); |
|
BUFG CLK0_BUFG_INST ( |
.I(CLK0_BUF), |
.O(CLKFB_IN) |
); |
|
BUFG CLKDV_BUFG_INST ( |
.I(CLKDV_BUF), |
.O(CLKDV_OUT) |
); |
|
`ifdef MINSOC_DLL |
|
CLKDLL #( |
.CLKDV_DIVIDE(divisor), // Divide by: 1.5,2.0,2.5,3.0,4.0,5.0,8.0 or 16.0 |
.DUTY_CYCLE_CORRECTION("TRUE"), // Duty cycle correction, TRUE or FALSE |
.FACTORY_JF(16'hC080), // FACTORY JF Values |
.STARTUP_WAIT("FALSE") // Delay config DONE until DLL LOCK, TRUE/FALSE |
) CLKDLL_inst ( |
.CLK0(CLK0_BUF), // 0 degree DLL CLK output |
.CLK180(), // 180 degree DLL CLK output |
.CLK270(), // 270 degree DLL CLK output |
.CLK2X(), // 2X DLL CLK output |
.CLK90(), // 90 degree DLL CLK output |
.CLKDV(CLKDV_BUF), // Divided DLL CLK out (CLKDV_DIVIDE) |
.LOCKED(), // DLL LOCK status output |
.CLKFB(CLKFB_IN), // DLL clock feedback |
.CLKIN(CLKIN_IBUFG), // Clock input (from IBUFG, BUFG or DLL) |
.RST(1'b0) // DLL asynchronous reset input |
); |
|
`elsif MINSOC_DCM |
|
DCM #( |
.SIM_MODE("SAFE"), // Simulation: "SAFE" vs. "FAST", see "Synthesis and Simulation Design Guide" for details |
.CLKDV_DIVIDE(divisor), // Divide by: 1.5,2.0,2.5,3.0,3.5,4.0,4.5,5.0,5.5,6.0,6.5 |
// 7.0,7.5,8.0,9.0,10.0,11.0,12.0,13.0,14.0,15.0 or 16.0 |
.CLKFX_DIVIDE(1), // Can be any integer from 1 to 32 |
.CLKFX_MULTIPLY(4), // Can be any integer from 2 to 32 |
.CLKIN_DIVIDE_BY_2("FALSE"), // TRUE/FALSE to enable CLKIN divide by two feature |
.CLKIN_PERIOD(0.0), // Specify period of input clock |
.CLKOUT_PHASE_SHIFT("NONE"), // Specify phase shift of NONE, FIXED or VARIABLE |
.CLK_FEEDBACK("1X"), // Specify clock feedback of NONE, 1X or 2X |
.DESKEW_ADJUST("SYSTEM_SYNCHRONOUS"), // SOURCE_SYNCHRONOUS, SYSTEM_SYNCHRONOUS or |
// an integer from 0 to 15 |
.DFS_FREQUENCY_MODE("LOW"), // HIGH or LOW frequency mode for frequency synthesis |
.DLL_FREQUENCY_MODE("LOW"), // HIGH or LOW frequency mode for DLL |
.DUTY_CYCLE_CORRECTION("TRUE"), // Duty cycle correction, TRUE or FALSE |
.FACTORY_JF(16'hC080), // FACTORY JF values |
.PHASE_SHIFT(0), // Amount of fixed phase shift from -255 to 255 |
.STARTUP_WAIT("FALSE") // Delay configuration DONE until DCM LOCK, TRUE/FALSE |
) DCM_inst ( |
.CLK0(CLK0_BUF), // 0 degree DCM CLK output |
.CLK180(), // 180 degree DCM CLK output |
.CLK270(), // 270 degree DCM CLK output |
.CLK2X(), // 2X DCM CLK output |
.CLK2X180(), // 2X, 180 degree DCM CLK out |
.CLK90(), // 90 degree DCM CLK output |
.CLKDV(CLKDV_BUF), // Divided DCM CLK out (CLKDV_DIVIDE) |
.CLKFX(), // DCM CLK synthesis out (M/D) |
.CLKFX180(), // 180 degree CLK synthesis out |
.LOCKED(), // DCM LOCK status output |
.PSDONE(), // Dynamic phase adjust done output |
.STATUS(), // 8-bit DCM status bits output |
.CLKFB(CLKFB_IN), // DCM clock feedback |
.CLKIN(CLKIN_IBUFG), // Clock input (from IBUFG, BUFG or DCM) |
.PSCLK(1'b0), // Dynamic phase adjust clock input |
.PSEN(1'b0), // Dynamic phase adjust enable input |
.PSINCDEC(1'b0), // Dynamic phase adjust increment/decrement |
.RST(1'b0) // DCM asynchronous reset input |
); |
|
`elsif MINSOC_DCM_SP |
|
DCM_SP #( |
.CLKDV_DIVIDE(divisor), // Divide by: 1.5,2.0,2.5,3.0,3.5,4.0,4.5,5.0,5.5,6.0,6.5 |
// 7.0,7.5,8.0,9.0,10.0,11.0,12.0,13.0,14.0,15.0 or 16.0 |
.CLKFX_DIVIDE(1), // Can be any integer from 1 to 32 |
.CLKFX_MULTIPLY(4), // Can be any integer from 2 to 32 |
.CLKIN_DIVIDE_BY_2("FALSE"), // TRUE/FALSE to enable CLKIN divide by two feature |
.CLKIN_PERIOD(0.0), // Specify period of input clock |
.CLKOUT_PHASE_SHIFT("NONE"), // Specify phase shift of NONE, FIXED or VARIABLE |
.CLK_FEEDBACK("1X"), // Specify clock feedback of NONE, 1X or 2X |
.DESKEW_ADJUST("SYSTEM_SYNCHRONOUS"), // SOURCE_SYNCHRONOUS, SYSTEM_SYNCHRONOUS or |
// an integer from 0 to 15 |
.DLL_FREQUENCY_MODE("LOW"), // HIGH or LOW frequency mode for DLL |
.DUTY_CYCLE_CORRECTION("TRUE"), // Duty cycle correction, TRUE or FALSE |
.PHASE_SHIFT(0), // Amount of fixed phase shift from -255 to 255 |
.STARTUP_WAIT("FALSE") // Delay configuration DONE until DCM LOCK, TRUE/FALSE |
) DCM_SP_inst ( |
.CLK0(CLK0_BUF), // 0 degree DCM CLK output |
.CLK180(), // 180 degree DCM CLK output |
.CLK270(), // 270 degree DCM CLK output |
.CLK2X(), // 2X DCM CLK output |
.CLK2X180(), // 2X, 180 degree DCM CLK out |
.CLK90(), // 90 degree DCM CLK output |
.CLKDV(CLKDV_BUF), // Divided DCM CLK out (CLKDV_DIVIDE) |
.CLKFX(), // DCM CLK synthesis out (M/D) |
.CLKFX180(), // 180 degree CLK synthesis out |
.LOCKED(), // DCM LOCK status output |
.PSDONE(), // Dynamic phase adjust done output |
.STATUS(), // 8-bit DCM status bits output |
.CLKFB(CLKFB_IN), // DCM clock feedback |
.CLKIN(CLKIN_IBUFG), // Clock input (from IBUFG, BUFG or DCM) |
.PSCLK(1'b0), // Dynamic phase adjust clock input |
.PSEN(1'b0), // Dynamic phase adjust enable input |
.PSINCDEC(1'b0), // Dynamic phase adjust increment/decrement |
.RST(1'b0) // DCM asynchronous reset input |
); |
|
`elsif MINSOC_DCM_ADV |
|
DCM_ADV #( |
.CLKDV_DIVIDE(divisor), // Divide by: 1.5,2.0,2.5,3.0,3.5,4.0,4.5,5.0,5.5,6.0,6.5 |
// 7.0,7.5,8.0,9.0,10.0,11.0,12.0,13.0,14.0,15.0 or 16.0 |
.CLKFX_DIVIDE(1), // Can be any integer from 1 to 32 |
.CLKFX_MULTIPLY(4), // Can be any integer from 2 to 32 |
.CLKIN_DIVIDE_BY_2("FALSE"), // TRUE/FALSE to enable CLKIN divide by two feature |
.CLKIN_PERIOD(10.0), // Specify period of input clock in ns from 1.25 to 1000.00 |
.CLKOUT_PHASE_SHIFT("NONE"), // Specify phase shift mode of NONE, FIXED, |
// VARIABLE_POSITIVE, VARIABLE_CENTER or DIRECT |
.CLK_FEEDBACK("1X"), // Specify clock feedback of NONE, 1X or 2X |
.DCM_AUTOCALIBRATION("TRUE"), // DCM calibration circuitry "TRUE"/"FALSE" |
.DCM_PERFORMANCE_MODE("MAX_SPEED"), // Can be MAX_SPEED or MAX_RANGE |
.DESKEW_ADJUST("SYSTEM_SYNCHRONOUS"), // SOURCE_SYNCHRONOUS, SYSTEM_SYNCHRONOUS or |
// an integer from 0 to 15 |
.DFS_FREQUENCY_MODE("LOW"), // HIGH or LOW frequency mode for frequency synthesis |
.DLL_FREQUENCY_MODE("LOW"), // LOW, HIGH, or HIGH_SER frequency mode for DLL |
.DUTY_CYCLE_CORRECTION("TRUE"), // Duty cycle correction, "TRUE"/"FALSE" |
.FACTORY_JF(16'hf0f0), // FACTORY JF value suggested to be set to 16’hf0f0 |
.PHASE_SHIFT(0), // Amount of fixed phase shift from -255 to 1023 |
.SIM_DEVICE(`MINSOC_DCM_COMPONENT), // Set target device, "VIRTEX4" or "VIRTEX5" |
.STARTUP_WAIT("FALSE") // Delay configuration DONE until DCM LOCK, "TRUE"/"FALSE" |
) DCM_ADV_inst ( |
.CLK0(CLK0_BUF), // 0 degree DCM CLK output |
.CLK180(), // 180 degree DCM CLK output |
.CLK270(), // 270 degree DCM CLK output |
.CLK2X(), // 2X DCM CLK output |
.CLK2X180(), // 2X, 180 degree DCM CLK out |
.CLK90(), // 90 degree DCM CLK output |
.CLKDV(CLKDV_BUF), // Divided DCM CLK out (CLKDV_DIVIDE) |
.CLKFX(), // DCM CLK synthesis out (M/D) |
.CLKFX180(), // 180 degree CLK synthesis out |
.DO(), // 16-bit data output for Dynamic Reconfiguration Port (DRP) |
.DRDY(), // Ready output signal from the DRP |
.LOCKED(), // DCM LOCK status output |
.PSDONE(), // Dynamic phase adjust done output |
.CLKFB(CLKFB_IN), // DCM clock feedback |
.CLKIN(CLKIN_IBUFG), // Clock input (from IBUFG, BUFG or DCM) |
.DADDR(7'h00), // 7-bit address for the DRP |
.DCLK(1'b0), // Clock for the DRP |
.DEN(1'b0), // Enable input for the DRP |
.DI(16'h0000), // 16-bit data input for the DRP |
.DWE(1'b0), // Active high allows for writing configuration memory |
.PSCLK(1'b0), // Dynamic phase adjust clock input |
.PSEN(1'b0), // Dynamic phase adjust enable input |
.PSINCDEC(1'b0), // Dynamic phase adjust increment/decrement |
.RST(1'b0) // DCM asynchronous reset input |
); |
|
`endif // !MINSOC_DLL/MINSOC_DCM/MINSOC_DCM_SP/MINSOC_DCM_ADV |
`endif // !ALTERA_FPGA/XILINX_FPGA |
`endif // !NO_CLOCK_DIVISION/GENERIC_CLOCK_DIVISION/FPGA_CLOCK_DIVISION |
|
/trunk/rtl/verilog/minsoc_pll.v
0,0 → 1,287
// megafunction wizard: %ALTPLL% |
// GENERATION: STANDARD |
// VERSION: WM1.0 |
// MODULE: altpll |
|
// ============================================================ |
// File Name: minsocPll.v |
// Megafunction Name(s): |
// altpll |
// |
// Simulation Library Files(s): |
// altera_mf |
// ============================================================ |
// ************************************************************ |
// THIS IS A WIZARD-GENERATED FILE. DO NOT EDIT THIS FILE! |
// |
// 10.1 Build 153 11/29/2010 SJ Web Edition |
// ************************************************************ |
|
// synopsys translate_off |
`timescale 1 ps / 1 ps |
// synopsys translate_on |
module minsoc_pll ( |
inclk0, |
c0); |
|
parameter FREQ_MULT = 1; |
parameter FREQ_DIV = 1; |
parameter FAMILY = "Cyclone III"; |
|
input inclk0; |
output c0; |
|
wire [4:0] sub_wire0; |
wire [0:0] sub_wire4 = 1'h0; |
wire [0:0] sub_wire1 = sub_wire0[0:0]; |
wire c0 = sub_wire1; |
wire sub_wire2 = inclk0; |
wire [1:0] sub_wire3 = {sub_wire4, sub_wire2}; |
|
altpll altpll_component ( |
.inclk (sub_wire3), |
.clk (sub_wire0), |
.activeclock (), |
.areset (1'b0), |
.clkbad (), |
.clkena ({6{1'b1}}), |
.clkloss (), |
.clkswitch (1'b0), |
.configupdate (1'b0), |
.enable0 (), |
.enable1 (), |
.extclk (), |
.extclkena ({4{1'b1}}), |
.fbin (1'b1), |
.fbmimicbidir (), |
.fbout (), |
.fref (), |
.icdrclk (), |
.locked (), |
.pfdena (1'b1), |
.phasecounterselect ({4{1'b1}}), |
.phasedone (), |
.phasestep (1'b1), |
.phaseupdown (1'b1), |
.pllena (1'b1), |
.scanaclr (1'b0), |
.scanclk (1'b0), |
.scanclkena (1'b1), |
.scandata (1'b0), |
.scandataout (), |
.scandone (), |
.scanread (1'b0), |
.scanwrite (1'b0), |
.sclkout0 (), |
.sclkout1 (), |
.vcooverrange (), |
.vcounderrange ()); |
defparam |
altpll_component.bandwidth_type = "AUTO", |
altpll_component.clk0_divide_by = FREQ_DIV, |
altpll_component.clk0_duty_cycle = 50, |
altpll_component.clk0_multiply_by = FREQ_MULT, |
altpll_component.clk0_phase_shift = "0", |
altpll_component.compensate_clock = "CLK0", |
altpll_component.inclk0_input_frequency = 20000, |
altpll_component.intended_device_family = FAMILY, |
altpll_component.lpm_hint = "CBX_MODULE_PREFIX=minsocPll", |
altpll_component.lpm_type = "altpll", |
altpll_component.operation_mode = "NORMAL", |
altpll_component.pll_type = "AUTO", |
altpll_component.port_activeclock = "PORT_UNUSED", |
altpll_component.port_areset = "PORT_UNUSED", |
altpll_component.port_clkbad0 = "PORT_UNUSED", |
altpll_component.port_clkbad1 = "PORT_UNUSED", |
altpll_component.port_clkloss = "PORT_UNUSED", |
altpll_component.port_clkswitch = "PORT_UNUSED", |
altpll_component.port_configupdate = "PORT_UNUSED", |
altpll_component.port_fbin = "PORT_UNUSED", |
altpll_component.port_inclk0 = "PORT_USED", |
altpll_component.port_inclk1 = "PORT_UNUSED", |
altpll_component.port_locked = "PORT_UNUSED", |
altpll_component.port_pfdena = "PORT_UNUSED", |
altpll_component.port_phasecounterselect = "PORT_UNUSED", |
altpll_component.port_phasedone = "PORT_UNUSED", |
altpll_component.port_phasestep = "PORT_UNUSED", |
altpll_component.port_phaseupdown = "PORT_UNUSED", |
altpll_component.port_pllena = "PORT_UNUSED", |
altpll_component.port_scanaclr = "PORT_UNUSED", |
altpll_component.port_scanclk = "PORT_UNUSED", |
altpll_component.port_scanclkena = "PORT_UNUSED", |
altpll_component.port_scandata = "PORT_UNUSED", |
altpll_component.port_scandataout = "PORT_UNUSED", |
altpll_component.port_scandone = "PORT_UNUSED", |
altpll_component.port_scanread = "PORT_UNUSED", |
altpll_component.port_scanwrite = "PORT_UNUSED", |
altpll_component.port_clk0 = "PORT_USED", |
altpll_component.port_clk1 = "PORT_UNUSED", |
altpll_component.port_clk2 = "PORT_UNUSED", |
altpll_component.port_clk3 = "PORT_UNUSED", |
altpll_component.port_clk4 = "PORT_UNUSED", |
altpll_component.port_clk5 = "PORT_UNUSED", |
altpll_component.port_clkena0 = "PORT_UNUSED", |
altpll_component.port_clkena1 = "PORT_UNUSED", |
altpll_component.port_clkena2 = "PORT_UNUSED", |
altpll_component.port_clkena3 = "PORT_UNUSED", |
altpll_component.port_clkena4 = "PORT_UNUSED", |
altpll_component.port_clkena5 = "PORT_UNUSED", |
altpll_component.port_extclk0 = "PORT_UNUSED", |
altpll_component.port_extclk1 = "PORT_UNUSED", |
altpll_component.port_extclk2 = "PORT_UNUSED", |
altpll_component.port_extclk3 = "PORT_UNUSED", |
altpll_component.width_clock = 5; |
endmodule |
|
// ============================================================ |
// CNX file retrieval info |
// ============================================================ |
// Retrieval info: PRIVATE: ACTIVECLK_CHECK STRING "0" |
// Retrieval info: PRIVATE: BANDWIDTH STRING "1.000" |
// Retrieval info: PRIVATE: BANDWIDTH_FEATURE_ENABLED STRING "1" |
// Retrieval info: PRIVATE: BANDWIDTH_FREQ_UNIT STRING "MHz" |
// Retrieval info: PRIVATE: BANDWIDTH_PRESET STRING "Low" |
// Retrieval info: PRIVATE: BANDWIDTH_USE_AUTO STRING "1" |
// Retrieval info: PRIVATE: BANDWIDTH_USE_PRESET STRING "0" |
// Retrieval info: PRIVATE: CLKBAD_SWITCHOVER_CHECK STRING "0" |
// Retrieval info: PRIVATE: CLKLOSS_CHECK STRING "0" |
// Retrieval info: PRIVATE: CLKSWITCH_CHECK STRING "0" |
// Retrieval info: PRIVATE: CNX_NO_COMPENSATE_RADIO STRING "0" |
// Retrieval info: PRIVATE: CREATE_CLKBAD_CHECK STRING "0" |
// Retrieval info: PRIVATE: CREATE_INCLK1_CHECK STRING "0" |
// Retrieval info: PRIVATE: CUR_DEDICATED_CLK STRING "c0" |
// Retrieval info: PRIVATE: CUR_FBIN_CLK STRING "c0" |
// Retrieval info: PRIVATE: DEVICE_SPEED_GRADE STRING "8" |
// Retrieval info: PRIVATE: DIV_FACTOR0 NUMERIC "4" |
// Retrieval info: PRIVATE: DUTY_CYCLE0 STRING "50.00000000" |
// Retrieval info: PRIVATE: EFF_OUTPUT_FREQ_VALUE0 STRING "62.500000" |
// Retrieval info: PRIVATE: EXPLICIT_SWITCHOVER_COUNTER STRING "0" |
// Retrieval info: PRIVATE: EXT_FEEDBACK_RADIO STRING "0" |
// Retrieval info: PRIVATE: GLOCKED_COUNTER_EDIT_CHANGED STRING "1" |
// Retrieval info: PRIVATE: GLOCKED_FEATURE_ENABLED STRING "0" |
// Retrieval info: PRIVATE: GLOCKED_MODE_CHECK STRING "0" |
// Retrieval info: PRIVATE: GLOCK_COUNTER_EDIT NUMERIC "1048575" |
// Retrieval info: PRIVATE: HAS_MANUAL_SWITCHOVER STRING "1" |
// Retrieval info: PRIVATE: INCLK0_FREQ_EDIT STRING "50.000" |
// Retrieval info: PRIVATE: INCLK0_FREQ_UNIT_COMBO STRING "MHz" |
// Retrieval info: PRIVATE: INCLK1_FREQ_EDIT STRING "100.000" |
// Retrieval info: PRIVATE: INCLK1_FREQ_EDIT_CHANGED STRING "1" |
// Retrieval info: PRIVATE: INCLK1_FREQ_UNIT_CHANGED STRING "1" |
// Retrieval info: PRIVATE: INCLK1_FREQ_UNIT_COMBO STRING "MHz" |
// Retrieval info: PRIVATE: INTENDED_DEVICE_FAMILY STRING "Cyclone III" |
// Retrieval info: PRIVATE: INT_FEEDBACK__MODE_RADIO STRING "1" |
// Retrieval info: PRIVATE: LOCKED_OUTPUT_CHECK STRING "0" |
// Retrieval info: PRIVATE: LONG_SCAN_RADIO STRING "1" |
// Retrieval info: PRIVATE: LVDS_MODE_DATA_RATE STRING "Not Available" |
// Retrieval info: PRIVATE: LVDS_MODE_DATA_RATE_DIRTY NUMERIC "0" |
// Retrieval info: PRIVATE: LVDS_PHASE_SHIFT_UNIT0 STRING "deg" |
// Retrieval info: PRIVATE: MIG_DEVICE_SPEED_GRADE STRING "Any" |
// Retrieval info: PRIVATE: MIRROR_CLK0 STRING "0" |
// Retrieval info: PRIVATE: MULT_FACTOR0 NUMERIC "5" |
// Retrieval info: PRIVATE: NORMAL_MODE_RADIO STRING "1" |
// Retrieval info: PRIVATE: OUTPUT_FREQ0 STRING "100.00000000" |
// Retrieval info: PRIVATE: OUTPUT_FREQ_MODE0 STRING "0" |
// Retrieval info: PRIVATE: OUTPUT_FREQ_UNIT0 STRING "MHz" |
// Retrieval info: PRIVATE: PHASE_RECONFIG_FEATURE_ENABLED STRING "1" |
// Retrieval info: PRIVATE: PHASE_RECONFIG_INPUTS_CHECK STRING "0" |
// Retrieval info: PRIVATE: PHASE_SHIFT0 STRING "0.00000000" |
// Retrieval info: PRIVATE: PHASE_SHIFT_STEP_ENABLED_CHECK STRING "0" |
// Retrieval info: PRIVATE: PHASE_SHIFT_UNIT0 STRING "deg" |
// Retrieval info: PRIVATE: PLL_ADVANCED_PARAM_CHECK STRING "0" |
// Retrieval info: PRIVATE: PLL_ARESET_CHECK STRING "0" |
// Retrieval info: PRIVATE: PLL_AUTOPLL_CHECK NUMERIC "1" |
// Retrieval info: PRIVATE: PLL_ENHPLL_CHECK NUMERIC "0" |
// Retrieval info: PRIVATE: PLL_FASTPLL_CHECK NUMERIC "0" |
// Retrieval info: PRIVATE: PLL_FBMIMIC_CHECK STRING "0" |
// Retrieval info: PRIVATE: PLL_LVDS_PLL_CHECK NUMERIC "0" |
// Retrieval info: PRIVATE: PLL_PFDENA_CHECK STRING "0" |
// Retrieval info: PRIVATE: PLL_TARGET_HARCOPY_CHECK NUMERIC "0" |
// Retrieval info: PRIVATE: PRIMARY_CLK_COMBO STRING "inclk0" |
// Retrieval info: PRIVATE: RECONFIG_FILE STRING "minsocPll.mif" |
// Retrieval info: PRIVATE: SACN_INPUTS_CHECK STRING "0" |
// Retrieval info: PRIVATE: SCAN_FEATURE_ENABLED STRING "1" |
// Retrieval info: PRIVATE: SELF_RESET_LOCK_LOSS STRING "0" |
// Retrieval info: PRIVATE: SHORT_SCAN_RADIO STRING "0" |
// Retrieval info: PRIVATE: SPREAD_FEATURE_ENABLED STRING "0" |
// Retrieval info: PRIVATE: SPREAD_FREQ STRING "50.000" |
// Retrieval info: PRIVATE: SPREAD_FREQ_UNIT STRING "KHz" |
// Retrieval info: PRIVATE: SPREAD_PERCENT STRING "0.500" |
// Retrieval info: PRIVATE: SPREAD_USE STRING "0" |
// Retrieval info: PRIVATE: SRC_SYNCH_COMP_RADIO STRING "0" |
// Retrieval info: PRIVATE: STICKY_CLK0 STRING "1" |
// Retrieval info: PRIVATE: SWITCHOVER_COUNT_EDIT NUMERIC "1" |
// Retrieval info: PRIVATE: SWITCHOVER_FEATURE_ENABLED STRING "1" |
// Retrieval info: PRIVATE: SYNTH_WRAPPER_GEN_POSTFIX STRING "0" |
// Retrieval info: PRIVATE: USE_CLK0 STRING "1" |
// Retrieval info: PRIVATE: USE_CLKENA0 STRING "0" |
// Retrieval info: PRIVATE: USE_MIL_SPEED_GRADE NUMERIC "0" |
// Retrieval info: PRIVATE: ZERO_DELAY_RADIO STRING "0" |
// Retrieval info: LIBRARY: altera_mf altera_mf.altera_mf_components.all |
// Retrieval info: CONSTANT: BANDWIDTH_TYPE STRING "AUTO" |
// Retrieval info: CONSTANT: CLK0_DIVIDE_BY NUMERIC "4" |
// Retrieval info: CONSTANT: CLK0_DUTY_CYCLE NUMERIC "50" |
// Retrieval info: CONSTANT: CLK0_MULTIPLY_BY NUMERIC "5" |
// Retrieval info: CONSTANT: CLK0_PHASE_SHIFT STRING "0" |
// Retrieval info: CONSTANT: COMPENSATE_CLOCK STRING "CLK0" |
// Retrieval info: CONSTANT: INCLK0_INPUT_FREQUENCY NUMERIC "20000" |
// Retrieval info: CONSTANT: INTENDED_DEVICE_FAMILY STRING "Cyclone III" |
// Retrieval info: CONSTANT: LPM_TYPE STRING "altpll" |
// Retrieval info: CONSTANT: OPERATION_MODE STRING "NORMAL" |
// Retrieval info: CONSTANT: PLL_TYPE STRING "AUTO" |
// Retrieval info: CONSTANT: PORT_ACTIVECLOCK STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_ARESET STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_CLKBAD0 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_CLKBAD1 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_CLKLOSS STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_CLKSWITCH STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_CONFIGUPDATE STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_FBIN STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_INCLK0 STRING "PORT_USED" |
// Retrieval info: CONSTANT: PORT_INCLK1 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_LOCKED STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_PFDENA STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_PHASECOUNTERSELECT STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_PHASEDONE STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_PHASESTEP STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_PHASEUPDOWN STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_PLLENA STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_SCANACLR STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_SCANCLK STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_SCANCLKENA STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_SCANDATA STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_SCANDATAOUT STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_SCANDONE STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_SCANREAD STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_SCANWRITE STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clk0 STRING "PORT_USED" |
// Retrieval info: CONSTANT: PORT_clk1 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clk2 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clk3 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clk4 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clk5 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clkena0 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clkena1 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clkena2 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clkena3 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clkena4 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_clkena5 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_extclk0 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_extclk1 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_extclk2 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: PORT_extclk3 STRING "PORT_UNUSED" |
// Retrieval info: CONSTANT: WIDTH_CLOCK NUMERIC "5" |
// Retrieval info: USED_PORT: @clk 0 0 5 0 OUTPUT_CLK_EXT VCC "@clk[4..0]" |
// Retrieval info: USED_PORT: c0 0 0 0 0 OUTPUT_CLK_EXT VCC "c0" |
// Retrieval info: USED_PORT: inclk0 0 0 0 0 INPUT_CLK_EXT GND "inclk0" |
// Retrieval info: CONNECT: @inclk 0 0 1 1 GND 0 0 0 0 |
// Retrieval info: CONNECT: @inclk 0 0 1 0 inclk0 0 0 0 0 |
// Retrieval info: CONNECT: c0 0 0 0 0 @clk 0 0 1 0 |
// Retrieval info: GEN_FILE: TYPE_NORMAL minsocPll.v TRUE |
// Retrieval info: GEN_FILE: TYPE_NORMAL minsocPll.ppf TRUE |
// Retrieval info: GEN_FILE: TYPE_NORMAL minsocPll.inc FALSE |
// Retrieval info: GEN_FILE: TYPE_NORMAL minsocPll.cmp FALSE |
// Retrieval info: GEN_FILE: TYPE_NORMAL minsocPll.bsf FALSE |
// Retrieval info: GEN_FILE: TYPE_NORMAL minsocPll_inst.v FALSE |
// Retrieval info: GEN_FILE: TYPE_NORMAL minsocPll_bb.v FALSE |
// Retrieval info: LIB_FILE: altera_mf |
// Retrieval info: CBX_MODULE_PREFIX: ON |