Line 2... |
Line 2... |
//
|
//
|
// Filename: altbusmaster.v
|
// Filename: altbusmaster.v
|
//
|
//
|
// Project: CMod S6 System on a Chip, ZipCPU demonstration project
|
// Project: CMod S6 System on a Chip, ZipCPU demonstration project
|
//
|
//
|
// Purpose:
|
// Purpose: Because the S6 is *so* small logic-wise, the logic of setting up
|
|
// a project/design was separated from the logic of the design
|
|
// itself. Hence, this is the "setup" design. It allows us to test various
|
|
// components from the command line interface, as well as erasing and
|
|
// programming the flash in order to set up the actual device interface.
|
//
|
//
|
// Creator: Dan Gisselquist, Ph.D.
|
// Creator: Dan Gisselquist, Ph.D.
|
// Gisselquist Technology, LLC
|
// Gisselquist Technology, LLC
|
//
|
//
|
////////////////////////////////////////////////////////////////////////////////
|
////////////////////////////////////////////////////////////////////////////////
|
//
|
//
|
// Copyright (C) 2015-2016, Gisselquist Technology, LLC
|
// Copyright (C) 2015-2017, Gisselquist Technology, LLC
|
//
|
//
|
// This program is free software (firmware): you can redistribute it and/or
|
// This program is free software (firmware): you can redistribute it and/or
|
// modify it under the terms of the GNU General Public License as published
|
// modify it under the terms of the GNU General Public License as published
|
// by the Free Software Foundation, either version 3 of the License, or (at
|
// by the Free Software Foundation, either version 3 of the License, or (at
|
// your option) any later version.
|
// your option) any later version.
|
Line 33... |
Line 37... |
//
|
//
|
//
|
//
|
////////////////////////////////////////////////////////////////////////////////
|
////////////////////////////////////////////////////////////////////////////////
|
//
|
//
|
//
|
//
|
//
|
|
`include "builddate.v"
|
`include "builddate.v"
|
//
|
//
|
// `define IMPLEMENT_ONCHIP_RAM
|
// `define IMPLEMENT_ONCHIP_RAM
|
`ifndef VERILATOR
|
|
`define FANCY_ICAP_ACCESS
|
|
`endif
|
|
`define FLASH_ACCESS
|
`define FLASH_ACCESS
|
`define DBG_SCOPE // About 204 LUTs, at 2^6 addresses
|
// `define DBG_SCOPE // About 204 LUTs, at 2^6 addresses
|
// `define COMPRESSED_SCOPE
|
// `define COMPRESSED_SCOPE
|
`define INCLUDE_SECOND_TIMER
|
|
`define SECOND_TIMER_IS_WATCHDOG
|
|
`define INCLUDE_RTC // About 90 LUTs
|
|
`define FULL_BUSERR_CALCULATION
|
|
`define WBUBUS
|
`define WBUBUS
|
module altbusmaster(i_clk, i_rst,
|
module altbusmaster(i_clk, i_rst,
|
// DEPP I/O Control
|
// DEPP I/O Control
|
i_depp_astb_n, i_depp_dstb_n, i_depp_write_n,
|
i_depp_astb_n, i_depp_dstb_n, i_depp_write_n,
|
i_depp_data, o_depp_data, o_depp_wait,
|
i_depp_data, o_depp_data, o_depp_wait,
|
// External UART interface
|
// External UART interface
|
i_rx_stb, i_rx_data, o_tx_stb, o_tx_data, i_tx_busy,
|
i_rx_stb, i_rx_data, o_tx_stb, o_tx_data, i_tx_busy,
|
o_uart_cts,
|
o_uart_rts_n,
|
// The SPI Flash lines
|
// The SPI Flash lines
|
o_qspi_cs_n, o_qspi_sck, o_qspi_dat, i_qspi_dat, o_qspi_mod,
|
o_qspi_cs_n, o_qspi_sck, o_qspi_dat, i_qspi_dat, o_qspi_mod,
|
// The board I/O
|
// The board I/O
|
i_btn, o_led, o_pwm, o_pwm_aux,
|
i_btn, o_led, o_pwm, o_pwm_aux,
|
// Keypad connections
|
// Keypad connections
|
Line 67... |
Line 63... |
o_uart_setup,
|
o_uart_setup,
|
// GPIO lines
|
// GPIO lines
|
i_gpio, o_gpio);
|
i_gpio, o_gpio);
|
parameter BUS_ADDRESS_WIDTH=23,
|
parameter BUS_ADDRESS_WIDTH=23,
|
BAW=BUS_ADDRESS_WIDTH; // 24bits->2,258,23b->2181
|
BAW=BUS_ADDRESS_WIDTH; // 24bits->2,258,23b->2181
|
|
// 2^14 bytes requires a LGMEMSZ of 14, and 12 address bits ranging from
|
|
// 0 to 11. As with many other devices, the wb_cyc line is more for
|
|
// form than anything else--it is ignored by the memory itself.
|
|
localparam LGMEMSZ=14; // Takes 8 BLKRAM16 elements for LGMEMSZ=14
|
|
// As with the memory size, the flash size is also measured in log_2 of
|
|
// the number of bytes.
|
|
localparam LGFLASHSZ = 24;
|
input i_clk, i_rst;
|
input i_clk, i_rst;
|
// The bus commander, via an external DEPP port
|
// The bus commander, via an external DEPP port
|
input i_depp_astb_n, i_depp_dstb_n, i_depp_write_n;
|
input i_depp_astb_n, i_depp_dstb_n, i_depp_write_n;
|
input wire [7:0] i_depp_data;
|
input wire [7:0] i_depp_data;
|
output wire [7:0] o_depp_data;
|
output wire [7:0] o_depp_data;
|
Line 79... |
Line 82... |
input i_rx_stb;
|
input i_rx_stb;
|
input [7:0] i_rx_data;
|
input [7:0] i_rx_data;
|
output reg o_tx_stb;
|
output reg o_tx_stb;
|
output reg [7:0] o_tx_data;
|
output reg [7:0] o_tx_data;
|
input i_tx_busy;
|
input i_tx_busy;
|
output wire o_uart_cts;
|
output wire o_uart_rts_n;
|
// SPI flash control
|
// SPI flash control
|
output wire o_qspi_cs_n, o_qspi_sck;
|
output wire o_qspi_cs_n, o_qspi_sck;
|
output wire [3:0] o_qspi_dat;
|
output wire [3:0] o_qspi_dat;
|
input [3:0] i_qspi_dat;
|
input [3:0] i_qspi_dat;
|
output wire [1:0] o_qspi_mod;
|
output wire [1:0] o_qspi_mod;
|
Line 94... |
Line 97... |
output wire [1:0] o_pwm_aux;
|
output wire [1:0] o_pwm_aux;
|
// Keypad
|
// Keypad
|
input [3:0] i_kp_row;
|
input [3:0] i_kp_row;
|
output wire [3:0] o_kp_col;
|
output wire [3:0] o_kp_col;
|
// UART control
|
// UART control
|
output wire [29:0] o_uart_setup;
|
output wire [30:0] o_uart_setup;
|
// GPIO liines
|
// GPIO liines
|
input [15:0] i_gpio;
|
input [15:0] i_gpio;
|
output wire [15:0] o_gpio;
|
output wire [15:0] o_gpio;
|
|
|
|
|
Line 108... |
Line 111... |
//
|
//
|
//
|
//
|
wire wb_cyc, wb_stb, wb_we, wb_stall, wb_ack, wb_err;
|
wire wb_cyc, wb_stb, wb_we, wb_stall, wb_ack, wb_err;
|
wire [31:0] wb_data, wb_idata, w_wbu_addr;
|
wire [31:0] wb_data, wb_idata, w_wbu_addr;
|
wire [(BAW-1):0] wb_addr;
|
wire [(BAW-1):0] wb_addr;
|
wire [5:0] io_addr;
|
|
assign io_addr = {
|
|
wb_addr[22], // Flash
|
|
wb_addr[13], // RAM
|
|
wb_addr[11], // RTC
|
|
wb_addr[10], // CFG
|
|
wb_addr[ 9], // SCOPE
|
|
wb_addr[ 8] }; // I/O
|
|
|
|
// Wires going to devices
|
// Wires going to devices
|
// And then headed back home
|
// And then headed back home
|
wire w_interrupt;
|
wire w_interrupt;
|
`ifdef WBUBUS
|
`ifdef WBUBUS
|
Line 134... |
Line 129... |
i_depp_astb_n, i_depp_dstb_n, i_depp_write_n,
|
i_depp_astb_n, i_depp_dstb_n, i_depp_write_n,
|
i_depp_data, o_depp_data, o_depp_wait,
|
i_depp_data, o_depp_data, o_depp_wait,
|
dep_rx_stb, dep_rx_data,
|
dep_rx_stb, dep_rx_data,
|
dep_tx_stb, dep_tx_data, dep_tx_busy);
|
dep_tx_stb, dep_tx_data, dep_tx_busy);
|
|
|
wbubus busbdriver(i_clk,
|
wire bus_dbg;
|
|
wbubus #(22) busbdriver(i_clk,
|
// i_rx_stb, i_rx_data, // UART control
|
// i_rx_stb, i_rx_data, // UART control
|
dep_rx_stb, dep_rx_data, // DEPP control
|
dep_rx_stb, dep_rx_data, // DEPP control
|
// The wishbone interface
|
// The wishbone interface
|
wb_cyc, wb_stb, wb_we, w_wbu_addr, wb_data,
|
wb_cyc, wb_stb, wb_we, w_wbu_addr, wb_data,
|
wb_ack, wb_stall, wb_err, wb_idata,
|
wb_ack, wb_stall, wb_err, wb_idata,
|
w_interrupt,
|
w_interrupt,
|
// Provide feedback to the DEPP interface
|
// Provide feedback to the DEPP interface
|
dep_tx_stb, dep_tx_data, dep_tx_busy);
|
dep_tx_stb, dep_tx_data, dep_tx_busy,
|
|
bus_dbg);
|
// // Provide feedback to the UART
|
// // Provide feedback to the UART
|
// o_tx_stb, o_tx_data, i_tx_busy
|
// o_tx_stb, o_tx_data, i_tx_busy
|
// assign o_uart_rts = (~rx_rdy);
|
// assign o_uart_rts = (~rx_rdy);
|
|
|
|
wire [30:0] bus_debug;
|
|
assign bus_debug = {
|
|
wb_cyc, wb_stb, wb_ack, wb_stall,
|
|
wb_addr[7:0],
|
|
dep_rx_stb, (~dep_tx_busy)&&(dep_tx_stb), dep_tx_stb,
|
|
dep_rx_data, dep_tx_data };
|
`else
|
`else
|
//
|
//
|
//
|
//
|
// Another BUS master (source): A conversion from DEPP to busmaster
|
// Another BUS master (source): A conversion from DEPP to busmaster
|
//
|
//
|
Line 160... |
Line 164... |
wb_cyc, wb_stb, wb_we, w_wbu_addr, wb_data,
|
wb_cyc, wb_stb, wb_we, w_wbu_addr, wb_data,
|
wb_ack, wb_stall, wb_err, wb_idata,
|
wb_ack, wb_stall, wb_err, wb_idata,
|
w_interrupt);
|
w_interrupt);
|
`endif
|
`endif
|
|
|
generate
|
|
if (BAW < 32)
|
|
assign wb_addr = w_wbu_addr[(BAW-1):0];
|
assign wb_addr = w_wbu_addr[(BAW-1):0];
|
else
|
|
assign wb_addr = w_wbu_addr;
|
|
endgenerate
|
|
|
|
wire io_sel, flash_sel, flctl_sel, scop_sel, cfg_sel, mem_sel,
|
|
rtc_sel, none_sel, many_sel;
|
// Signals to build/detect bus errors
|
|
wire none_sel, many_sel;
|
|
|
|
wire io_sel, flash_sel, flctl_sel, scop_sel, mem_sel;
|
wire flash_ack, scop_ack, cfg_ack, mem_ack, many_ack;
|
wire flash_ack, scop_ack, cfg_ack, mem_ack, many_ack;
|
wire rtc_ack, rtc_stall;
|
|
`ifdef INCLUDE_RTC
|
|
assign rtc_stall = 1'b0;
|
|
`endif
|
|
wire io_stall, flash_stall, scop_stall, cfg_stall, mem_stall;
|
wire io_stall, flash_stall, scop_stall, cfg_stall, mem_stall;
|
reg io_ack;
|
reg io_ack;
|
|
|
wire [31:0] flash_data, scop_data, cfg_data, mem_data, pwm_data,
|
wire [31:0] flash_data, scop_data, cfg_data, mem_data, pwm_data,
|
spio_data, gpio_data, uart_data;
|
spio_data, gpio_data, uart_data;
|
reg [31:0] io_data;
|
reg [31:0] io_data;
|
reg [(BAW-1):0] bus_err_addr;
|
reg [(BAW-1):0] bus_err_addr;
|
|
//
|
|
// wb_ack
|
|
//
|
|
// The returning wishbone ack is equal to the OR of every component that
|
|
// might possibly produce an acknowledgement, gated by the CYC line. To
|
|
// add new components, OR their acknowledgements in here.
|
|
//
|
|
// Note the reference to none_sel. If nothing is selected, the result
|
|
// is an error. Here, we do nothing more than insure that the erroneous
|
|
// request produces an ACK ... if it was ever made, rather than stalling
|
|
// the bus.
|
|
//
|
|
|
assign wb_ack = (wb_cyc)&&((io_ack)||(scop_ack)||(cfg_ack)
|
|
`ifdef INCLUDE_RTC
|
assign wb_ack = (wb_cyc)&&((io_ack)||(scop_ack)
|
||(rtc_ack)
|
|
`endif
|
|
||(mem_ack)||(flash_ack)||((none_sel)&&(1'b1)));
|
||(mem_ack)||(flash_ack)||((none_sel)&&(1'b1)));
|
|
|
|
//
|
|
// wb_stall
|
|
//
|
|
// The returning wishbone stall line really depends upon what device
|
|
// is requested. Thus, if a particular device is selected, we return
|
|
// the stall line for that device.
|
|
//
|
|
// To add a new device, simply and that devices select and stall lines
|
|
// together, and OR the result with the massive OR logic below.
|
|
//
|
assign wb_stall = ((io_sel)&&(io_stall))
|
assign wb_stall = ((io_sel)&&(io_stall))
|
||((scop_sel)&&(scop_stall))
|
||((scop_sel)&&(scop_stall))
|
||((cfg_sel)&&(cfg_stall))
|
|
||((mem_sel)&&(mem_stall))
|
||((mem_sel)&&(mem_stall))
|
`ifdef INCLUDE_RTC
|
|
||((rtc_sel)&&(rtc_stall))
|
|
`endif
|
|
||((flash_sel||flctl_sel)&&(flash_stall));
|
||((flash_sel||flctl_sel)&&(flash_stall));
|
// (none_sel)&&(1'b0)
|
// (none_sel)&&(1'b0)
|
|
|
/*
|
//
|
assign wb_idata = (io_ack)?io_data
|
// wb_idata
|
: ((scop_ack)?scop_data
|
//
|
: ((cfg_ack)?cfg_data
|
// This is the data returned on the bus. Here, we select between a
|
: ((mem_ack)?mem_data
|
// series of bus sources to select what data to return. The basic
|
: ((flash_ack)?flash_data
|
// logic is simply this: the data we return is the data for which the
|
: 32'h00))));
|
// ACK line is high.
|
*/
|
//
|
|
// The last item on the list is chosen by default if no other ACK's are
|
|
// true. Although we might choose to return zeros in that case, by
|
|
// returning something we can skimp a touch on the logic.
|
|
//
|
|
// To add another device, add another ack check, and another closing
|
|
// parenthesis.
|
|
//
|
assign wb_idata = (io_ack|scop_ack)?((io_ack )? io_data : scop_data)
|
assign wb_idata = (io_ack|scop_ack)?((io_ack )? io_data : scop_data)
|
: ((mem_ack|rtc_ack)?((mem_ack)?mem_data:rtc_data)
|
: ((mem_ack)?(mem_data)
|
: ((cfg_ack) ? cfg_data : flash_data));//if (flash_ack)
|
: flash_data);
|
assign wb_err = ((wb_cyc)&&(wb_stb)&&(none_sel || many_sel)) || many_ack;
|
|
|
//
|
|
// wb_err
|
|
//
|
|
// This is the bus error signal. It should never be true, but practice
|
|
// teaches us otherwise. Here, we allow for three basic errors:
|
|
//
|
|
// 1. STB is true, but no devices are selected
|
|
//
|
|
// This is the null pointer reference bug. If you try to access
|
|
// something on the bus, at an address with no mapping, the bus
|
|
// should produce an error--such as if you try to access something
|
|
// at zero.
|
|
//
|
|
// 2. STB is true, and more than one device is selected
|
|
//
|
|
// (This can be turned off, if you design this file well. For
|
|
// this line to be true means you have a design flaw.)
|
|
//
|
|
// 3. If more than one ACK is every true at any given time.
|
|
//
|
|
// This is a bug of bus usage, combined with a subtle flaw in the
|
|
// WB pipeline definition. You can issue bus requests, one per
|
|
// clock, and if you cross device boundaries with your requests,
|
|
// you may have things come back out of order (not detected here)
|
|
// or colliding on return (detected here). The solution to this
|
|
// problem is to make certain that any burst request does not cross
|
|
// device boundaries. This is a requirement of whoever (or
|
|
// whatever) drives the bus.
|
|
//
|
|
assign wb_err = ((wb_stb)&&(none_sel || many_sel)) || many_ack;
|
|
|
// Addresses ...
|
// Addresses ...
|
// 0000 xxxx configuration/control registers
|
//
|
// 1 xxxx xxxx xxxx xxxx xxxx Up-sampler taps
|
// dev_sel
|
assign io_sel =((wb_cyc)&&(io_addr[5:0]==6'h1));
|
//
|
assign scop_sel =((wb_cyc)&&(io_addr[5:0]==6'h2));
|
// The device select lines
|
assign flctl_sel=((wb_cyc)&&(io_addr[5:0]==6'h3));
|
//
|
assign cfg_sel =((wb_cyc)&&(io_addr[5:1]==5'h2));
|
//
|
// zip_sel is not on the bus at this point
|
|
`ifdef INCLUDE_RTC
|
|
assign rtc_sel =((wb_cyc)&&(io_addr[5:3]==3'h1));
|
|
`endif
|
|
assign mem_sel =((wb_cyc)&&(io_addr[5:4]==2'h1));
|
|
assign flash_sel=((wb_cyc)&&(io_addr[5]));
|
|
|
|
`ifdef FULL_BUSERR_CALCULATION
|
//
|
assign none_sel =((wb_cyc)&&(wb_stb)&&
|
// The skipaddr bitfield below is our cheaters way of handling
|
((io_addr==6'h0)
|
// device selection. We grab particular wires from the bus to do
|
||((~io_addr[5])&&(|wb_addr[22:14]))
|
// this, and ignore all others. While this may lead to some
|
||((io_addr[5:4]==2'b00)&&(|wb_addr[12])))
|
// surprising results for the CPU when it tries to access an
|
);
|
// inappropriate address, it also minimizes our logic while also
|
assign many_sel =((wb_cyc)&&(wb_stb)&&(
|
// placing every address at the right address. The only problem is
|
{3'h0, io_sel}
|
// ... devices will also be at some unexpected addresses, but ... this
|
+{3'h0, flctl_sel}
|
// is still within our spec.
|
+{3'h0, scop_sel}
|
//
|
+{3'h0, cfg_sel}
|
wire [3:0] skipaddr;
|
+{3'h0, rtc_sel}
|
assign skipaddr = {
|
+{3'h0, mem_sel}
|
wb_addr[(LGFLASHSZ-2)], // Flash
|
+{3'h0, flash_sel} > 1));
|
wb_addr[(LGMEMSZ-2)], // RAM
|
|
wb_addr[ 9], // SCOPE
|
assign many_ack =((wb_cyc)&&(
|
wb_addr[ 8] }; // I/O
|
{3'h0, io_ack}
|
//
|
+{3'h0, scop_ack}
|
// This might not be the most efficient way in hardware, but it will
|
+{3'h0, cfg_ack}
|
// work for our purposes here. There are two phantom bits for each
|
`ifdef INCLUDE_RTC
|
// of these ... bits that tell the CPU which byte within the word, and
|
+{3'h0, rtc_ack}
|
// another phantom bit because we allocated a minimum of two words to
|
|
// every device.
|
|
//
|
|
wire idle_n;
|
|
`ifdef ZERO_ON_IDLE
|
|
assign idle_n = wb_stb;
|
|
`else
|
|
assign idle_n = 1'b1;
|
`endif
|
`endif
|
+{3'h0, mem_ack}
|
|
+{3'h0, flash_ack} > 1));
|
// `define ZERO_ON_IDLE
|
|
`ifdef ZERO_ON_IDLE
|
|
assign idle_n = (wb_cyc)&&(wb_stb);
|
`else
|
`else
|
assign many_ack = 1'b0;
|
assign idle_n = 1'b1;
|
assign many_sel = 1'b0;
|
|
assign none_sel =((wb_cyc)&&(wb_stb)&&(io_addr==6'h0));
|
|
`endif
|
`endif
|
|
assign io_sel =((idle_n)&&(skipaddr[3:0]==4'h1));
|
|
assign scop_sel =((idle_n)&&(skipaddr[3:1]==3'h1)); // = 4'h2
|
|
assign flctl_sel= 1'b0; // ((wb_cyc)&&(skipaddr[3:0]==4'h3));
|
|
assign mem_sel =((idle_n)&&(skipaddr[3:2]==2'h1));
|
|
assign flash_sel=((idle_n)&&(skipaddr[3]));
|
|
|
|
//
|
|
// none_sel
|
|
//
|
|
// This wire is true if wb_stb is true and no device is selected. This
|
|
// is an error condition, but here we present the logic to test for it.
|
|
//
|
|
//
|
|
// If you add another device, add another OR into the select lines
|
|
// associated with this term.
|
|
//
|
|
assign none_sel =((wb_stb)&&(skipaddr==4'h0));
|
|
|
|
//
|
|
// many_sel
|
|
//
|
|
// This should *never* be true .... unless you mess up your address
|
|
// decoding logic. Since I've done that before, I test/check for it
|
|
// here.
|
|
//
|
|
// To add a new device here, simply add it to the list. Make certain
|
|
// that the width of the add, however, is greater than the number
|
|
// of devices below. Hence, for 3 devices, you will need an add
|
|
// at least 3 bits in width, for 7 devices you will need at least 4
|
|
// bits, etc.
|
|
//
|
|
// Because this add uses the {} operator, the individual components to
|
|
// it are by default unsigned ... just as we would like.
|
|
//
|
|
// There's probably another easier/better/faster/cheaper way to do this,
|
|
// but I haven't found any such that are also easier to adjust with
|
|
// new devices. I'm open to options.
|
|
//
|
|
assign many_sel = 1'b0;
|
|
|
|
//
|
|
// many_ack
|
|
//
|
|
// Normally this would capture the error when multiple things creates acks
|
|
// at the same time. The S6 is small, though, and doesn't have the logic
|
|
// we need to do this right. Hence we just declare (and hope) that this
|
|
// will never be true and work with that.
|
|
//
|
|
assign many_ack = 1'b0;
|
|
|
wire flash_interrupt, scop_interrupt, tmra_int, tmrb_int,
|
wire flash_interrupt, scop_interrupt, tmra_int, tmrb_int,
|
rtc_interrupt, gpio_int, pwm_int, keypad_int,button_int;
|
gpio_int, pwm_int, keypad_int,button_int;
|
|
|
|
|
//
|
//
|
|
// bus_err_addr
|
|
//
|
|
// We'd like to know, after the fact, what (if any) address caused a
|
|
// bus error. So ... if we get a bus error, let's record the address
|
|
// on the bus for later analysis.
|
|
//
|
|
initial bus_err_addr = 0;
|
|
always @(posedge i_clk)
|
|
if (wb_err)
|
|
bus_err_addr <= wb_addr;
|
|
//
|
|
// Interrupt processing
|
|
//
|
|
// The interrupt controller will be used to tell us if any interrupts
|
|
// take place.
|
//
|
//
|
|
// To add more interrupts, you can just add more wires to this int_vector
|
|
// for the new interrupts.
|
//
|
//
|
reg rx_rdy;
|
reg rx_rdy;
|
wire [11:0] int_vector;
|
wire [11:0] int_vector;
|
assign int_vector = {
|
assign int_vector = {
|
flash_interrupt, gpio_int, pwm_int, keypad_int,
|
flash_interrupt, gpio_int, pwm_int, keypad_int,
|
(~o_tx_stb), rx_rdy,
|
(!o_tx_stb), rx_rdy,
|
tmrb_int, tmra_int,
|
tmrb_int, tmra_int,
|
rtc_interrupt, scop_interrupt,
|
1'b0, scop_interrupt,
|
wb_err, button_int };
|
wb_err, button_int };
|
|
|
wire [31:0] pic_data;
|
wire [31:0] pic_data;
|
icontrol #(12) pic(i_clk, 1'b0, (wb_stb)&&(io_sel)
|
icontrol #(12) pic(i_clk, 1'b0, (wb_stb)&&(io_sel)
|
&&(wb_addr[3:0]==4'h0)&&(wb_we),
|
&&(wb_addr[3:0]==4'h0)&&(wb_we),
|
wb_data, pic_data, int_vector, w_interrupt);
|
wb_data, pic_data, int_vector, w_interrupt);
|
|
|
initial bus_err_addr = 0; // `DATESTAMP;
|
wire [31:0] timer_data, timer_b;
|
always @(posedge i_clk)
|
|
if (wb_err)
|
|
bus_err_addr <= wb_addr;
|
|
|
|
wire [31:0] timer_a, timer_b;
|
|
wire zta_ack, zta_stall, ztb_ack, ztb_stall;
|
wire zta_ack, zta_stall, ztb_ack, ztb_stall;
|
ziptimer #(32,31,1)
|
ziptimer #(32,31,1)
|
zipt_a(i_clk, 1'b0, 1'b1, wb_cyc,
|
thetimer(i_clk, 1'b0, 1'b1, wb_cyc,
|
`ifdef INCLUDE_SECOND_TIMER
|
|
(wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h2),
|
(wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h2),
|
`else
|
wb_we, wb_data, zta_ack, zta_stall, timer_data,
|
(wb_stb)&&(io_sel)&&(wb_addr[3:1]==3'h1),
|
|
`endif
|
|
wb_we, wb_data, zta_ack, zta_stall, timer_a,
|
|
tmra_int);
|
tmra_int);
|
`ifdef INCLUDE_SECOND_TIMER
|
|
`ifdef SECOND_TIMER_IS_WATCHDOG
|
|
ziptimer #(32,31,0)
|
ziptimer #(32,31,0)
|
zipt_b(i_clk, 1'b0, 1'b1, wb_cyc,
|
zipt_b(i_clk, 1'b0, 1'b1, wb_cyc,
|
(wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h3),
|
(wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h3),
|
wb_we, wb_data, ztb_ack, ztb_stall, timer_b,
|
wb_we, wb_data, ztb_ack, ztb_stall, timer_b,
|
tmrb_int);
|
tmrb_int);
|
`else
|
|
ziptimer #(32,31,1)
|
|
zipt_b(i_clk, 1'b0, 1'b1, wb_cyc,
|
|
(wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h3),
|
|
wb_we, wb_data, ztb_ack, ztb_stall, timer_b,
|
|
tmrb_int);
|
|
`endif
|
|
`else
|
|
// assign timer_b = 32'h000;
|
|
assign timer_b = timer_a;
|
|
assign tmrb_int = 1'b0;
|
|
`endif
|
|
|
|
wire [31:0] rtc_data;
|
|
`ifdef INCLUDE_RTC
|
|
wire rtcd_ack, rtcd_stall, ppd;
|
|
// rtcdate thedate(i_clk, ppd, wb_cyc, (wb_stb)&&(io_sel), wb_we,
|
|
// wb_data, rtcd_ack, rtcd_stall, date_data);
|
|
reg r_rtc_ack;
|
|
initial r_rtc_ack = 1'b0;
|
|
always @(posedge i_clk)
|
|
r_rtc_ack <= ((wb_stb)&&(rtc_sel));
|
|
assign rtc_ack = r_rtc_ack;
|
|
|
|
rtclight
|
|
#(23'h35afe5,23,0,0) // 80 MHz clock
|
|
thetime(i_clk, wb_cyc,
|
|
((wb_stb)&&(rtc_sel)), wb_we,
|
|
{ 1'b0, wb_addr[1:0] }, wb_data, rtc_data,
|
|
rtc_interrupt, ppd);
|
|
`else
|
|
assign rtc_interrupt = 1'b0;
|
|
assign rtc_data = 32'h00;
|
|
assign rtc_ack = 1'b0;
|
|
`endif
|
|
|
|
always @(posedge i_clk)
|
always @(posedge i_clk)
|
case(wb_addr[3:0])
|
case(wb_addr[3:0])
|
4'h0: io_data <= pic_data;
|
4'h0: io_data <= pic_data;
|
4'h1: io_data <= { {(32-BAW){1'b0}}, bus_err_addr };
|
4'h1: io_data <= { {(30-BAW){1'b0}}, bus_err_addr, 2'b00 };
|
4'h2: io_data <= timer_a;
|
4'h2: io_data <= timer_data;
|
4'h3: io_data <= timer_b;
|
4'h3: io_data <= timer_b;
|
4'h4: io_data <= pwm_data;
|
4'h4: io_data <= pwm_data;
|
4'h5: io_data <= spio_data;
|
4'h5: io_data <= spio_data;
|
4'h6: io_data <= gpio_data;
|
4'h6: io_data <= gpio_data;
|
4'h7: io_data <= uart_data;
|
4'h7: io_data <= uart_data;
|
default: io_data <= `DATESTAMP;
|
default: io_data <= `DATESTAMP;
|
// 4'h8: io_data <= `DATESTAMP;
|
// 4'h8: io_data <= `DATESTAMP;
|
endcase
|
endcase
|
always @(posedge i_clk)
|
always @(posedge i_clk)
|
io_ack <= (wb_cyc)&&(wb_stb)&&(io_sel);
|
io_ack <= (wb_stb)&&(io_sel);
|
assign io_stall = 1'b0;
|
assign io_stall = 1'b0;
|
|
|
wire pwm_ack, pwm_stall;
|
wire pwm_ack, pwm_stall;
|
wbpwmaudio #(14'd10000,2,0,14)
|
wbpwmaudio #(14'd10000,2,0,14)
|
theaudio(i_clk, wb_cyc,
|
theaudio(i_clk, wb_cyc,
|
Line 363... |
Line 438... |
|
|
//
|
//
|
// Special Purpose I/O: Keypad, button, LED status and control
|
// Special Purpose I/O: Keypad, button, LED status and control
|
//
|
//
|
wire [3:0] w_led;
|
wire [3:0] w_led;
|
spio thespio(i_clk, wb_cyc,(wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h5),wb_we,
|
spio thespio(i_clk, wb_cyc,(wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h5),
|
wb_data, spio_data, o_kp_col, i_kp_row, i_btn, w_led,
|
wb_we, wb_data, spio_data,
|
|
o_kp_col, i_kp_row, i_btn, w_led,
|
keypad_int, button_int);
|
keypad_int, button_int);
|
assign o_led = { w_led[3]|w_interrupt,w_led[2],w_led[1:0] };
|
assign o_led = { w_led[3]|w_interrupt,w_led[2],w_led[1:0] };
|
|
|
//
|
//
|
// General purpose (sort of) I/O: (Bottom two bits robbed in each
|
// General purpose (sort of) I/O: (Bottom two bits robbed in each
|
Line 389... |
Line 465... |
// although the CPU might struggle to keep up at this speed without a
|
// although the CPU might struggle to keep up at this speed without a
|
// hardware buffer.
|
// hardware buffer.
|
//
|
//
|
// We'll add the flag for two stop bits.
|
// We'll add the flag for two stop bits.
|
// assign o_uart_setup = 30'h080002b6; // 115200 MBaud @ an 80MHz clock
|
// assign o_uart_setup = 30'h080002b6; // 115200 MBaud @ an 80MHz clock
|
assign o_uart_setup = 30'h0000208d; // 9600 MBaud, 8N1
|
assign o_uart_setup = 31'h4000208d; // 9600 MBaud, 8N1
|
|
|
initial o_tx_stb = 1'b0;
|
initial o_tx_stb = 1'b0;
|
initial o_tx_data = 8'h00;
|
initial o_tx_data = 8'h00;
|
always @(posedge i_clk)
|
always @(posedge i_clk)
|
if ((wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h7)&&(wb_we))
|
if ((wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h7)&&(wb_we))
|
Line 412... |
Line 488... |
if((wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h7)&&(~wb_we))
|
if((wb_stb)&&(io_sel)&&(wb_addr[3:0]==4'h7)&&(~wb_we))
|
rx_rdy <= i_rx_stb;
|
rx_rdy <= i_rx_stb;
|
else if (i_rx_stb)
|
else if (i_rx_stb)
|
rx_rdy <= (rx_rdy | i_rx_stb);
|
rx_rdy <= (rx_rdy | i_rx_stb);
|
end
|
end
|
assign o_uart_cts = (~rx_rdy);
|
assign o_uart_rts_n = (rx_rdy);
|
assign uart_data = { 23'h0, ~rx_rdy, r_rx_data };
|
assign uart_data = { 23'h0, ~rx_rdy, r_rx_data };
|
//
|
//
|
// uart_ack gets returned as part of io_ack, since that happens when
|
// uart_ack gets returned as part of io_ack, since that happens when
|
// io_sel and wb_stb are defined
|
// io_sel and wb_stb are defined
|
//
|
//
|
Line 426... |
Line 502... |
|
|
|
|
//
|
//
|
// FLASH MEMORY CONFIGURATION ACCESS
|
// FLASH MEMORY CONFIGURATION ACCESS
|
//
|
//
|
wbqspiflashp #(24) flashmem(i_clk,
|
`ifdef FLASH_ACCESS
|
|
wbqspiflash #(LGFLASHSZ) flashmem(i_clk,
|
wb_cyc,(wb_stb)&&(flash_sel),(wb_stb)&&(flctl_sel),wb_we,
|
wb_cyc,(wb_stb)&&(flash_sel),(wb_stb)&&(flctl_sel),wb_we,
|
wb_addr[(24-3):0], wb_data,
|
wb_addr[(LGFLASHSZ-3):0], wb_data,
|
flash_ack, flash_stall, flash_data,
|
flash_ack, flash_stall, flash_data,
|
o_qspi_sck, o_qspi_cs_n, o_qspi_mod, o_qspi_dat, i_qspi_dat,
|
o_qspi_sck, o_qspi_cs_n, o_qspi_mod, o_qspi_dat, i_qspi_dat,
|
flash_interrupt);
|
flash_interrupt);
|
|
|
//
|
|
// MULTIBOOT/ICAPE2 CONFIGURATION ACCESS
|
|
//
|
|
wire [31:0] cfg_scope;
|
|
`ifdef FANCY_ICAP_ACCESS
|
|
wbicape6 fpga_cfg(i_clk, wb_cyc,(cfg_sel)&&(wb_stb), wb_we,
|
|
wb_addr[5:0], wb_data,
|
|
cfg_ack, cfg_stall, cfg_data,
|
|
cfg_scope);
|
|
`else
|
`else
|
reg r_cfg_ack;
|
reg r_flash_ack;
|
|
initial r_flash_ack = 1'b0;
|
always @(posedge i_clk)
|
always @(posedge i_clk)
|
r_cfg_ack <= (wb_cyc)&&(cfg_sel)&&(wb_stb);
|
r_flash_ack <= (wb_stb)&&((flash_sel)||(flctl_sel));
|
assign cfg_ack = r_cfg_ack;
|
|
assign cfg_stall = 1'b0;
|
|
assign cfg_data = 32'h00;
|
|
assign cfg_scope = 32'h00;
|
|
`endif
|
|
|
|
|
assign flash_ack = r_flash_ack;
|
|
assign flash_stall = 1'b0;
|
|
assign flash_data = 32'h0000;
|
|
assign flash_interrupt = 1'b0;
|
|
|
|
assign o_qspi_sck = 1'b1;
|
|
assign o_qspi_cs_n = 1'b1;
|
|
assign o_qspi_mod = 2'b01;
|
|
assign o_qspi_dat = 4'b1111;
|
|
`endif
|
|
|
//
|
//
|
// ON-CHIP RAM MEMORY ACCESS
|
// ON-CHIP RAM MEMORY ACCESS
|
//
|
//
|
`ifdef IMPLEMENT_ONCHIP_RAM
|
`ifdef IMPLEMENT_ONCHIP_RAM
|
memdev #(12) ram(i_clk, wb_cyc, (wb_stb)&&(mem_sel), wb_we,
|
memdev #(.LGMEMSZ(LGMEMSZ))
|
wb_addr[11:0], wb_data, mem_ack, mem_stall, mem_data);
|
ram(i_clk, wb_cyc, (wb_stb)&&(mem_sel), wb_we,
|
|
wb_addr[(LGMEMSZ-3):0], wb_data, wb_sel,
|
|
mem_ack, mem_stall, mem_data);
|
`else
|
`else
|
assign mem_data = 32'h00;
|
assign mem_data = 32'h00;
|
assign mem_stall = 1'b0;
|
assign mem_stall = 1'b0;
|
reg r_mem_ack;
|
reg r_mem_ack;
|
always @(posedge i_clk)
|
always @(posedge i_clk)
|
r_mem_ack <= (wb_cyc)&&(wb_stb)&&(mem_sel);
|
r_mem_ack <= (wb_stb)&&(mem_sel);
|
assign mem_ack = r_mem_ack;
|
assign mem_ack = r_mem_ack;
|
`endif
|
`endif
|
|
|
//
|
//
|
//
|
//
|
Line 479... |
Line 554... |
//
|
//
|
wire [31:0] scop_cfg_data;
|
wire [31:0] scop_cfg_data;
|
wire scop_cfg_ack, scop_cfg_stall, scop_cfg_interrupt;
|
wire scop_cfg_ack, scop_cfg_stall, scop_cfg_interrupt;
|
`ifdef DBG_SCOPE
|
`ifdef DBG_SCOPE
|
wire scop_cfg_trigger;
|
wire scop_cfg_trigger;
|
assign scop_cfg_trigger = (wb_cyc)&&(wb_stb)&&(cfg_sel);
|
assign scop_cfg_trigger = (wb_stb)&&(cfg_sel);
|
wire scop_trigger = scop_cfg_trigger;
|
wire scop_trigger = bus_dbg;
|
`ifdef COMPRESSED_SCOPE
|
`ifdef COMPRESSED_SCOPE
|
wbscopc #(5'ha)
|
wbscopc #(5'ha)
|
`else
|
`else
|
wbscope #(5'ha)
|
wbscope #(5'ha)
|
`endif
|
`endif
|
wbcfgscope(i_clk, 1'b1, scop_trigger,
|
wbcfgscope(i_clk, 1'b1, scop_trigger, bus_debug,
|
cfg_scope,
|
|
// Wishbone interface
|
// Wishbone interface
|
i_clk, wb_cyc, (wb_stb)&&(scop_sel),
|
i_clk, wb_cyc, (wb_stb)&&(scop_sel),
|
wb_we, wb_addr[0], wb_data,
|
wb_we, wb_addr[0], wb_data,
|
scop_cfg_ack, scop_cfg_stall, scop_cfg_data,
|
scop_cfg_ack, scop_cfg_stall, scop_cfg_data,
|
scop_cfg_interrupt);
|
scop_cfg_interrupt);
|
`else
|
`else
|
reg r_scop_cfg_ack;
|
reg r_scop_cfg_ack;
|
always @(posedge i_clk)
|
always @(posedge i_clk)
|
r_scop_cfg_ack <= (wb_cyc)&&(wb_stb)&&(scop_sel);
|
r_scop_cfg_ack <= (wb_stb)&&(scop_sel);
|
assign scop_cfg_ack = r_scop_cfg_ack;
|
assign scop_cfg_ack = r_scop_cfg_ack;
|
assign scop_cfg_data = 32'h000;
|
assign scop_cfg_data = 32'h000;
|
assign scop_cfg_stall= 1'b0;
|
assign scop_cfg_stall= 1'b0;
|
`endif
|
`endif
|
|
|