//////////////////////////////////////////////////////////////////////
|
//////////////////////////////////////////////////////////////////////
|
//// ////
|
//// ////
|
//// File name "wbw_fifo_control.v" ////
|
//// File name "wbw_fifo_control.v" ////
|
//// ////
|
//// ////
|
//// This file is part of the "PCI bridge" project ////
|
//// This file is part of the "PCI bridge" project ////
|
//// http://www.opencores.org/cores/pci/ ////
|
//// http://www.opencores.org/cores/pci/ ////
|
//// ////
|
//// ////
|
//// Author(s): ////
|
//// Author(s): ////
|
//// - Miha Dolenc (mihad@opencores.org) ////
|
//// - Miha Dolenc (mihad@opencores.org) ////
|
//// ////
|
//// ////
|
//// All additional information is avaliable in the README ////
|
//// All additional information is avaliable in the README ////
|
//// file. ////
|
//// file. ////
|
//// ////
|
//// ////
|
//// ////
|
//// ////
|
//////////////////////////////////////////////////////////////////////
|
//////////////////////////////////////////////////////////////////////
|
//// ////
|
//// ////
|
//// Copyright (C) 2001 Miha Dolenc, mihad@opencores.org ////
|
//// Copyright (C) 2001 Miha Dolenc, mihad@opencores.org ////
|
//// ////
|
//// ////
|
//// This source file may be used and distributed without ////
|
//// This source file may be used and distributed without ////
|
//// restriction provided that this copyright statement is not ////
|
//// restriction provided that this copyright statement is not ////
|
//// removed from the file and that any derivative work contains ////
|
//// removed from the file and that any derivative work contains ////
|
//// the original copyright notice and the associated disclaimer. ////
|
//// the original copyright notice and the associated disclaimer. ////
|
//// ////
|
//// ////
|
//// This source file is free software; you can redistribute it ////
|
//// This source file is free software; you can redistribute it ////
|
//// and/or modify it under the terms of the GNU Lesser General ////
|
//// and/or modify it under the terms of the GNU Lesser General ////
|
//// Public License as published by the Free Software Foundation; ////
|
//// Public License as published by the Free Software Foundation; ////
|
//// either version 2.1 of the License, or (at your option) any ////
|
//// either version 2.1 of the License, or (at your option) any ////
|
//// later version. ////
|
//// later version. ////
|
//// ////
|
//// ////
|
//// This source is distributed in the hope that it will be ////
|
//// This source is distributed in the hope that it will be ////
|
//// useful, but WITHOUT ANY WARRANTY; without even the implied ////
|
//// useful, but WITHOUT ANY WARRANTY; without even the implied ////
|
//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR ////
|
//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR ////
|
//// PURPOSE. See the GNU Lesser General Public License for more ////
|
//// PURPOSE. See the GNU Lesser General Public License for more ////
|
//// details. ////
|
//// details. ////
|
//// ////
|
//// ////
|
//// You should have received a copy of the GNU Lesser General ////
|
//// You should have received a copy of the GNU Lesser General ////
|
//// Public License along with this source; if not, download it ////
|
//// Public License along with this source; if not, download it ////
|
//// from http://www.opencores.org/lgpl.shtml ////
|
//// from http://www.opencores.org/lgpl.shtml ////
|
//// ////
|
//// ////
|
//////////////////////////////////////////////////////////////////////
|
//////////////////////////////////////////////////////////////////////
|
//
|
//
|
// CVS Revision History
|
// CVS Revision History
|
//
|
//
|
// $Log: not supported by cvs2svn $
|
// $Log: not supported by cvs2svn $
|
// Revision 1.2 2001/10/05 08:14:30 mihad
|
// Revision 1.2 2001/10/05 08:14:30 mihad
|
// Updated all files with inclusion of timescale file for simulation purposes.
|
// Updated all files with inclusion of timescale file for simulation purposes.
|
//
|
//
|
// Revision 1.1.1.1 2001/10/02 15:33:47 mihad
|
// Revision 1.1.1.1 2001/10/02 15:33:47 mihad
|
// New project directory structure
|
// New project directory structure
|
//
|
//
|
//
|
//
|
|
|
/* FIFO_CONTROL module provides read/write address and status generation for
|
/* FIFO_CONTROL module provides read/write address and status generation for
|
FIFOs implemented with standard dual port SRAM cells in ASIC or FPGA designs */
|
FIFOs implemented with standard dual port SRAM cells in ASIC or FPGA designs */
|
`include "pci_constants.v"
|
`include "pci_constants.v"
|
// synopsys translate_off
|
// synopsys translate_off
|
`include "timescale.v"
|
`include "timescale.v"
|
// synopsys translate_on
|
// synopsys translate_on
|
|
|
module WBW_FIFO_CONTROL
|
module WBW_FIFO_CONTROL
|
(
|
(
|
rclock_in,
|
rclock_in,
|
wclock_in,
|
wclock_in,
|
renable_in,
|
renable_in,
|
wenable_in,
|
wenable_in,
|
reset_in,
|
reset_in,
|
flush_in,
|
flush_in,
|
almost_full_out,
|
almost_full_out,
|
full_out,
|
full_out,
|
empty_out,
|
empty_out,
|
waddr_out,
|
waddr_out,
|
raddr_out,
|
raddr_out,
|
rallow_out,
|
rallow_out,
|
wallow_out
|
wallow_out
|
);
|
);
|
|
|
parameter ADDR_LENGTH = 7 ;
|
parameter ADDR_LENGTH = 7 ;
|
|
|
// independent clock inputs - rclock_in = read clock, wclock_in = write clock
|
// independent clock inputs - rclock_in = read clock, wclock_in = write clock
|
input rclock_in, wclock_in;
|
input rclock_in, wclock_in;
|
|
|
// enable inputs - read address changes on rising edge of rclock_in when reads are allowed
|
// enable inputs - read address changes on rising edge of rclock_in when reads are allowed
|
// write address changes on rising edge of wclock_in when writes are allowed
|
// write address changes on rising edge of wclock_in when writes are allowed
|
input renable_in, wenable_in ;
|
input renable_in, wenable_in ;
|
|
|
// reset input
|
// reset input
|
input reset_in;
|
input reset_in;
|
|
|
// flush input
|
// flush input
|
input flush_in ;
|
input flush_in ;
|
|
|
// almost full and empy status outputs
|
// almost full and empy status outputs
|
output almost_full_out ;
|
output almost_full_out ;
|
|
|
// full and empty status outputs
|
// full and empty status outputs
|
output full_out, empty_out;
|
output full_out, empty_out;
|
|
|
// read and write addresses outputs
|
// read and write addresses outputs
|
output [(ADDR_LENGTH - 1):0] waddr_out, raddr_out;
|
output [(ADDR_LENGTH - 1):0] waddr_out, raddr_out;
|
|
|
// read and write allow outputs
|
// read and write allow outputs
|
output rallow_out, wallow_out ;
|
output rallow_out, wallow_out ;
|
|
|
// read address register
|
// read address register
|
reg [(ADDR_LENGTH - 1):0] raddr ;
|
reg [(ADDR_LENGTH - 1):0] raddr ;
|
|
|
// write address register
|
// write address register
|
reg [(ADDR_LENGTH - 1):0] waddr;
|
reg [(ADDR_LENGTH - 1):0] waddr;
|
assign waddr_out = waddr ;
|
assign waddr_out = waddr ;
|
|
|
// grey code registers
|
// grey code registers
|
// grey code pipeline for write address
|
// grey code pipeline for write address
|
reg [(ADDR_LENGTH - 1):0] wgrey_addr ; // current
|
reg [(ADDR_LENGTH - 1):0] wgrey_addr ; // current
|
reg [(ADDR_LENGTH - 1):0] wgrey_next ; // next
|
reg [(ADDR_LENGTH - 1):0] wgrey_next ; // next
|
|
|
// next write gray address calculation - bitwise xor between address and shifted address
|
// next write gray address calculation - bitwise xor between address and shifted address
|
wire [(ADDR_LENGTH - 2):0] calc_wgrey_next = waddr[(ADDR_LENGTH - 1):1] ^ waddr[(ADDR_LENGTH - 2):0] ;
|
wire [(ADDR_LENGTH - 2):0] calc_wgrey_next = waddr[(ADDR_LENGTH - 1):1] ^ waddr[(ADDR_LENGTH - 2):0] ;
|
|
|
// grey code pipeline for read address
|
// grey code pipeline for read address
|
reg [(ADDR_LENGTH - 1):0] rgrey_minus2 ; // two before current
|
reg [(ADDR_LENGTH - 1):0] rgrey_minus2 ; // two before current
|
reg [(ADDR_LENGTH - 1):0] rgrey_minus1 ; // one before current
|
reg [(ADDR_LENGTH - 1):0] rgrey_minus1 ; // one before current
|
reg [(ADDR_LENGTH - 1):0] rgrey_addr ; // current
|
reg [(ADDR_LENGTH - 1):0] rgrey_addr ; // current
|
reg [(ADDR_LENGTH - 1):0] rgrey_next ; // next
|
reg [(ADDR_LENGTH - 1):0] rgrey_next ; // next
|
|
|
// next read gray address calculation - bitwise xor between address and shifted address
|
// next read gray address calculation - bitwise xor between address and shifted address
|
wire [(ADDR_LENGTH - 2):0] calc_rgrey_next = raddr[(ADDR_LENGTH - 1):1] ^ raddr[(ADDR_LENGTH - 2):0] ;
|
wire [(ADDR_LENGTH - 2):0] calc_rgrey_next = raddr[(ADDR_LENGTH - 1):1] ^ raddr[(ADDR_LENGTH - 2):0] ;
|
|
|
// FFs for registered empty and full flags
|
// FFs for registered empty and full flags
|
reg empty ;
|
reg empty ;
|
reg full ;
|
reg full ;
|
|
|
// almost_full tag
|
// almost_full tag
|
reg almost_full ;
|
reg almost_full ;
|
|
|
// write allow wire - writes are allowed when fifo is not full
|
// write allow wire - writes are allowed when fifo is not full
|
wire wallow = wenable_in && ~full ;
|
wire wallow = wenable_in && ~full ;
|
|
|
// write allow output assignment
|
// write allow output assignment
|
assign wallow_out = wallow && ~full ;
|
assign wallow_out = wallow && ~full ;
|
|
|
// read allow wire
|
// read allow wire
|
wire rallow ;
|
wire rallow ;
|
|
|
// full output assignment
|
// full output assignment
|
assign full_out = full ;
|
assign full_out = full ;
|
|
|
// almost full output assignment
|
// almost full output assignment
|
assign almost_full_out = almost_full && ~full ;
|
assign almost_full_out = almost_full && ~full ;
|
|
|
// clear generation for FFs and registers
|
// clear generation for FFs and registers
|
wire clear = reset_in || flush_in ;
|
wire clear = reset_in || flush_in ;
|
|
|
reg wclock_nempty_detect ;
|
reg wclock_nempty_detect ;
|
always@(posedge reset_in or posedge wclock_in)
|
always@(posedge reset_in or posedge wclock_in)
|
begin
|
begin
|
if (reset_in)
|
if (reset_in)
|
wclock_nempty_detect <= #`FF_DELAY 1'b0 ;
|
wclock_nempty_detect <= #`FF_DELAY 1'b0 ;
|
else
|
else
|
wclock_nempty_detect <= #`FF_DELAY (rgrey_addr != wgrey_addr) ;
|
wclock_nempty_detect <= #`FF_DELAY (rgrey_addr != wgrey_addr) ;
|
end
|
end
|
|
|
// special synchronizing mechanism for different implementations - in synchronous imp., empty is prolonged for 1 clock edge if no write clock comes after initial write
|
// special synchronizing mechanism for different implementations - in synchronous imp., empty is prolonged for 1 clock edge if no write clock comes after initial write
|
reg stretched_empty ;
|
reg stretched_empty ;
|
always@(posedge rclock_in or posedge clear)
|
always@(posedge rclock_in or posedge clear)
|
begin
|
begin
|
if(clear)
|
if(clear)
|
stretched_empty <= #`FF_DELAY 1'b1 ;
|
stretched_empty <= #`FF_DELAY 1'b1 ;
|
else
|
else
|
stretched_empty <= #`FF_DELAY empty && ~wclock_nempty_detect ;
|
stretched_empty <= #`FF_DELAY empty && ~wclock_nempty_detect ;
|
end
|
end
|
|
|
// empty output is actual empty + 1 read clock cycle ( stretched empty )
|
// empty output is actual empty + 1 read clock cycle ( stretched empty )
|
assign empty_out = empty || stretched_empty ;
|
assign empty_out = empty || stretched_empty ;
|
|
|
//rallow generation
|
//rallow generation
|
assign rallow = renable_in && ~empty && ~stretched_empty ; // reads allowed if read enable is high and FIFO is not empty
|
assign rallow = renable_in && ~empty && ~stretched_empty ; // reads allowed if read enable is high and FIFO is not empty
|
|
|
// rallow output assignment
|
// rallow output assignment
|
assign rallow_out = rallow ;
|
assign rallow_out = rallow ;
|
|
|
// at any clock edge that rallow is high, this register provides next read address, so wait cycles are not necessary
|
// at any clock edge that rallow is high, this register provides next read address, so wait cycles are not necessary
|
// when FIFO is empty, this register provides actual read address, so first location can be read
|
// when FIFO is empty, this register provides actual read address, so first location can be read
|
reg [(ADDR_LENGTH - 1):0] raddr_plus_one ;
|
reg [(ADDR_LENGTH - 1):0] raddr_plus_one ;
|
|
|
// address output mux - when FIFO is empty, current actual address is driven out, when it is non - empty next address is driven out
|
// address output mux - when FIFO is empty, current actual address is driven out, when it is non - empty next address is driven out
|
// done for zero wait state burst
|
// done for zero wait state burst
|
assign raddr_out = rallow ? raddr_plus_one : raddr ;
|
assign raddr_out = rallow ? raddr_plus_one : raddr ;
|
|
|
always@(posedge rclock_in or posedge clear)
|
always@(posedge rclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
begin
|
begin
|
// initial value is important - raddr initial value is 4, so this one is 5
|
// initial value is important - raddr initial value is 4, so this one is 5
|
raddr_plus_one <= #`FF_DELAY 5 ;
|
raddr_plus_one <= #`FF_DELAY 5 ;
|
end
|
end
|
else if (rallow)
|
else if (rallow)
|
raddr_plus_one <= #`FF_DELAY raddr_plus_one + 1'b1 ;
|
raddr_plus_one <= #`FF_DELAY raddr_plus_one + 1'b1 ;
|
end
|
end
|
|
|
// raddr is filled with raddr_plus_one on rising read clock edge when rallow is high
|
// raddr is filled with raddr_plus_one on rising read clock edge when rallow is high
|
always@(posedge rclock_in or posedge clear)
|
always@(posedge rclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
// initial value is 4
|
// initial value is 4
|
raddr <= #`FF_DELAY 4 ;
|
raddr <= #`FF_DELAY 4 ;
|
else if (rallow)
|
else if (rallow)
|
raddr <= #`FF_DELAY raddr_plus_one ;
|
raddr <= #`FF_DELAY raddr_plus_one ;
|
end
|
end
|
|
|
/*-----------------------------------------------------------------------------------------------
|
/*-----------------------------------------------------------------------------------------------
|
Read address control consists of Read address counter and Grey Address pipeline
|
Read address control consists of Read address counter and Grey Address pipeline
|
There are 4 Grey addresses:
|
There are 4 Grey addresses:
|
- rgrey_minus2 is Grey Code of address two before current address
|
- rgrey_minus2 is Grey Code of address two before current address
|
- rgrey_minus1 is Grey Code of address one before current address
|
- rgrey_minus1 is Grey Code of address one before current address
|
- rgrey_addr is Grey Code of current read address
|
- rgrey_addr is Grey Code of current read address
|
- rgrey_next is Grey Code of next read address
|
- rgrey_next is Grey Code of next read address
|
--------------------------------------------------------------------------------------------------*/
|
--------------------------------------------------------------------------------------------------*/
|
|
|
// grey code register for two before read address
|
// grey code register for two before read address
|
always@(posedge rclock_in or posedge clear)
|
always@(posedge rclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
begin
|
begin
|
// initial value is 0
|
// initial value is 0
|
rgrey_minus2 <= #`FF_DELAY 0 ;
|
rgrey_minus2 <= #`FF_DELAY 0 ;
|
end
|
end
|
else
|
else
|
if (rallow)
|
if (rallow)
|
rgrey_minus2 <= #`FF_DELAY rgrey_minus1 ;
|
rgrey_minus2 <= #`FF_DELAY rgrey_minus1 ;
|
end
|
end
|
|
|
// grey code register for one before read address
|
// grey code register for one before read address
|
always@(posedge rclock_in or posedge clear)
|
always@(posedge rclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
begin
|
begin
|
// initial value is 1
|
// initial value is 1
|
rgrey_minus1 <= #`FF_DELAY 1 ;
|
rgrey_minus1 <= #`FF_DELAY 1 ;
|
end
|
end
|
else
|
else
|
if (rallow)
|
if (rallow)
|
rgrey_minus1 <= #`FF_DELAY rgrey_addr ;
|
rgrey_minus1 <= #`FF_DELAY rgrey_addr ;
|
end
|
end
|
|
|
// grey code register for read address - represents current Read Address
|
// grey code register for read address - represents current Read Address
|
always@(posedge rclock_in or posedge clear)
|
always@(posedge rclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
begin
|
begin
|
// initial value is 3 = ...00011
|
// initial value is 3 = ...00011
|
rgrey_addr <= #`FF_DELAY 3 ;
|
rgrey_addr <= #`FF_DELAY 3 ;
|
end
|
end
|
else
|
else
|
if (rallow)
|
if (rallow)
|
rgrey_addr <= #`FF_DELAY rgrey_next ;
|
rgrey_addr <= #`FF_DELAY rgrey_next ;
|
end
|
end
|
|
|
// grey code register for next read address - represents Grey Code of next read address
|
// grey code register for next read address - represents Grey Code of next read address
|
always@(posedge rclock_in or posedge clear)
|
always@(posedge rclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
begin
|
begin
|
// initial value is 2 = ...00010
|
// initial value is 2 = ...00010
|
rgrey_next <= #`FF_DELAY 2 ;
|
rgrey_next <= #`FF_DELAY 2 ;
|
end
|
end
|
else
|
else
|
if (rallow)
|
if (rallow)
|
rgrey_next <= #`FF_DELAY {raddr[ADDR_LENGTH - 1], calc_rgrey_next} ;
|
rgrey_next <= #`FF_DELAY {raddr[ADDR_LENGTH - 1], calc_rgrey_next} ;
|
end
|
end
|
|
|
/*--------------------------------------------------------------------------------------------
|
/*--------------------------------------------------------------------------------------------
|
Write address control consists of write address counter and two Grey Code Registers:
|
Write address control consists of write address counter and two Grey Code Registers:
|
- wgrey_addr represents current Grey Coded write address
|
- wgrey_addr represents current Grey Coded write address
|
- wgrey_next represents Grey Coded next write address
|
- wgrey_next represents Grey Coded next write address
|
----------------------------------------------------------------------------------------------*/
|
----------------------------------------------------------------------------------------------*/
|
// grey code register for write address
|
// grey code register for write address
|
always@(posedge wclock_in or posedge clear)
|
always@(posedge wclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
begin
|
begin
|
// initial value is 3 = ....011
|
// initial value is 3 = ....011
|
wgrey_addr <= #`FF_DELAY 3 ;
|
wgrey_addr <= #`FF_DELAY 3 ;
|
end
|
end
|
else
|
else
|
if (wallow)
|
if (wallow)
|
wgrey_addr <= #`FF_DELAY wgrey_next ;
|
wgrey_addr <= #`FF_DELAY wgrey_next ;
|
end
|
end
|
|
|
// grey code register for next write address
|
// grey code register for next write address
|
always@(posedge wclock_in or posedge clear)
|
always@(posedge wclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
begin
|
begin
|
// initial value is 2 = ...010
|
// initial value is 2 = ...010
|
wgrey_next <= #`FF_DELAY 2 ;
|
wgrey_next <= #`FF_DELAY 2 ;
|
end
|
end
|
else
|
else
|
if (wallow)
|
if (wallow)
|
wgrey_next <= #`FF_DELAY {waddr[(ADDR_LENGTH - 1)], calc_wgrey_next} ;
|
wgrey_next <= #`FF_DELAY {waddr[(ADDR_LENGTH - 1)], calc_wgrey_next} ;
|
end
|
end
|
|
|
// write address counter - nothing special - initial value is important though
|
// write address counter - nothing special - initial value is important though
|
always@(posedge wclock_in or posedge clear)
|
always@(posedge wclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
// initial value 4
|
// initial value 4
|
waddr <= #`FF_DELAY 4 ;
|
waddr <= #`FF_DELAY 4 ;
|
else
|
else
|
if (wallow)
|
if (wallow)
|
waddr <= #`FF_DELAY waddr + 1'b1 ;
|
waddr <= #`FF_DELAY waddr + 1'b1 ;
|
end
|
end
|
|
|
/*------------------------------------------------------------------------------------------------------------------------------
|
/*------------------------------------------------------------------------------------------------------------------------------
|
Registered full control:
|
Registered full control:
|
registered full is set on rising edge of wclock_in when there is one free location in and another written to fifo
|
registered full is set on rising edge of wclock_in when there is one free location in and another written to fifo
|
It's kept high until something is read from FIFO, which is registered on
|
It's kept high until something is read from FIFO, which is registered on
|
next rising write clock edge.
|
next rising write clock edge.
|
|
|
Registered almost full control:
|
Registered almost full control:
|
Almost full flag is set on rising wclock_in edge when there are two unused locations left in and another written to fifo.
|
Almost full flag is set on rising wclock_in edge when there are two unused locations left in and another written to fifo.
|
It is set until something is read/written from/to fifo
|
It is set until something is read/written from/to fifo
|
--------------------------------------------------------------------------------------------------------------------------------*/
|
--------------------------------------------------------------------------------------------------------------------------------*/
|
//combinatorial input to Registered full FlipFlop
|
//combinatorial input to Registered full FlipFlop
|
wire reg_full = wallow && (wgrey_next == rgrey_minus1) || (wgrey_next == rgrey_addr) ;
|
wire reg_full = wallow && (wgrey_next == rgrey_minus1) || (wgrey_next == rgrey_addr) ;
|
|
|
always@(posedge wclock_in or posedge clear)
|
always@(posedge wclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
full <= #`FF_DELAY 1'b0 ;
|
full <= #`FF_DELAY 1'b0 ;
|
else
|
else
|
full <= #`FF_DELAY reg_full ;
|
full <= #`FF_DELAY reg_full ;
|
end
|
end
|
|
|
// input for almost full latch
|
// input for almost full latch
|
wire reg_almost_full_in = wallow && (wgrey_next == rgrey_minus2) || (wgrey_next == rgrey_minus1) ;
|
wire reg_almost_full_in = wallow && (wgrey_next == rgrey_minus2) || (wgrey_next == rgrey_minus1) ;
|
|
|
always@(posedge clear or posedge wclock_in)
|
always@(posedge clear or posedge wclock_in)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
almost_full <= #`FF_DELAY 1'b0 ;
|
almost_full <= #`FF_DELAY 1'b0 ;
|
else
|
else
|
almost_full <= #`FF_DELAY reg_almost_full_in ;
|
almost_full <= #`FF_DELAY reg_almost_full_in ;
|
end
|
end
|
|
|
/*------------------------------------------------------------------------------------------------------------------------------
|
/*------------------------------------------------------------------------------------------------------------------------------
|
Registered empty control:
|
Registered empty control:
|
registered empty is set on rising edge of rclock_in when one location is used and read from fifo. It's kept high
|
registered empty is set on rising edge of rclock_in when one location is used and read from fifo. It's kept high
|
until something is written to the fifo, which is registered on the next clock edge.
|
until something is written to the fifo, which is registered on the next clock edge.
|
|
|
Registered almost empty control:
|
Registered almost empty control:
|
Almost empty is set on rising edge of rclock_in when two locations are used and one read. It's kept set until something
|
Almost empty is set on rising edge of rclock_in when two locations are used and one read. It's kept set until something
|
is read/written from/to fifo.
|
is read/written from/to fifo.
|
--------------------------------------------------------------------------------------------------------------------------------*/
|
--------------------------------------------------------------------------------------------------------------------------------*/
|
// combinatorial input for registered emty FlipFlop
|
// combinatorial input for registered emty FlipFlop
|
wire comb_almost_empty = (rgrey_next == wgrey_addr) ;
|
wire comb_almost_empty = (rgrey_next == wgrey_addr) ;
|
wire comb_empty = (rgrey_addr == wgrey_addr) ;
|
wire comb_empty = (rgrey_addr == wgrey_addr) ;
|
wire reg_empty = renable_in && comb_almost_empty || comb_empty ;
|
wire reg_empty = renable_in && comb_almost_empty || comb_empty ;
|
|
|
always@(posedge rclock_in or posedge clear)
|
always@(posedge rclock_in or posedge clear)
|
begin
|
begin
|
if (clear)
|
if (clear)
|
empty <= #`FF_DELAY 1'b1 ;
|
empty <= #`FF_DELAY 1'b1 ;
|
else
|
else
|
empty <= #`FF_DELAY reg_empty ;
|
empty <= #`FF_DELAY reg_empty ;
|
end
|
end
|
|
|
endmodule
|
endmodule
|
|
|