| Line 312... |
Line 312... |
|
|
cop_count_test;
|
cop_count_test;
|
|
|
cop_count_test_8;
|
cop_count_test_8;
|
|
|
$finish;
|
cop_irq_test;
|
|
|
u0.wb_write(1, SLAVE_0_CNTRL, COP_CNTRL_DEBUG_ENA); // Enable Slave Mode
|
|
|
|
// Set Master Mode PS=0, Modulo=16
|
|
test_num = test_num + 1;
|
|
$display("TEST #%d Starts at vector=%d, ms_test", test_num, vector);
|
|
|
|
u0.wb_write(1, COP_TOUT, 16'h0010); // load prescaler hi-byte
|
|
u0.wb_write(1, COP_CNTRL, COP_CNTRL_COP_ENA); // Enable to start counting
|
|
$display("status: %t programmed registers", $time);
|
|
|
|
wait_flag_set; // Wait for Counter to tomeout
|
|
u0.wb_write(1, COP_CNTRL, COP_CNTRL_STOP_ENA | COP_CNTRL_COP_ENA); //
|
|
|
|
wait_flag_set; // Wait for Counter to tomeout
|
|
u0.wb_write(1, COP_CNTRL, COP_CNTRL_STOP_ENA | COP_CNTRL_COP_ENA); //
|
|
|
|
repeat(10) @(posedge mstr_test_clk);
|
repeat(10) @(posedge mstr_test_clk);
|
u0.wb_write(1, COP_CNTRL, 16'b0); //
|
|
|
|
repeat(10) @(posedge mstr_test_clk);
|
|
|
|
repeat(100) @(posedge mstr_test_clk);
|
|
$display("\nTestbench done at vector=%d\n", vector);
|
$display("\nTestbench done at vector=%d\n", vector);
|
$finish;
|
$finish;
|
end
|
end
|
|
|
// Poll for flag set
|
// Poll for flag set
|
task wait_flag_set;
|
task wait_flag_set;
|
begin
|
begin
|
u0.wb_read(1, COP_CNTRL, q);
|
u0.wb_read(1, COP_CNTRL, q);
|
while(~|(q & COP_CNTRL_STOP_ENA))
|
while(~|(q & COP_CNTRL_COP_EVENT))
|
u0.wb_read(1, COP_CNTRL, q); // poll it until it is set
|
u0.wb_read(1, COP_CNTRL, q); // poll it until it is set
|
$display("COP Flag set detected at vector =%d", vector);
|
$display("COP Flag set detected at vector =%d", vector);
|
end
|
end
|
endtask
|
endtask
|
|
|
| Line 512... |
Line 492... |
u0.wb_cmp( 1, COP_CNTRL, COP_CNTRL_COP_ENA); // verify Status bit cleared
|
u0.wb_cmp( 1, COP_CNTRL, COP_CNTRL_COP_ENA); // verify Status bit cleared
|
|
|
end
|
end
|
endtask
|
endtask
|
|
|
|
task cop_irq_test;
|
|
begin
|
|
test_num = test_num + 1;
|
|
$display("TEST #%d Starts at vector=%d, cop_irq_test",
|
|
test_num, vector);
|
|
// program internal registers
|
|
u0.wb_write(1, COP_CNTRL, 16'h0000); // Turn off COP_ENA
|
|
u0.wb_write(1, COP_TOUT, 16'h0014); // Write TOUT reg
|
|
// u0.wb_write(1, COP_CNTRL, COP_CNTRL_IRQ | COP_CNTRL_COP_ENA); //
|
|
u0.wb_write(1, COP_CNTRL, 16'h0040 | COP_CNTRL_COP_ENA); //
|
|
send_x_osc_clks(10);
|
|
|
|
u0.wb_write(1, COP_CNTRL, 16'h0000); // Turn off COP_ENA
|
|
u0.wb_write(1, COP_TOUT, 16'h0022); // Write TOUT reg
|
|
send_x_osc_clks(1);
|
|
// u0.wb_write(1, COP_CNTRL, COP_CNTRL_IRQ | COP_CNTRL_COP_ENA); //
|
|
u0.wb_write(1, COP_CNTRL, 16'h0080 | COP_CNTRL_COP_ENA); //
|
|
send_x_osc_clks(10);
|
|
end
|
|
endtask
|
|
|
task cop_count_test_8;
|
task cop_count_test_8;
|
begin
|
begin
|
test_num = test_num + 1;
|
test_num = test_num + 1;
|
$display("TEST #%d Starts at vector=%d, cop_count_test_8",
|
$display("TEST #%d Starts at vector=%d, cop_count_test_8",
|
test_num, vector);
|
test_num, vector);
|
