| Line 1... |
Line 1... |
extern void uart_init(void);
|
|
extern void uart_putc(char);
|
|
extern char uart_getc(void);
|
|
extern void uart_print_str(char *);
|
|
extern void uart_print_long(unsigned long);
|
|
|
|
#if 1
|
|
#define UART_RX 0 /* In: Receive buffer (DLAB=0) */
|
|
#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */
|
|
#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
|
|
#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */
|
|
#define UART_IER 1 /* Out: Interrupt Enable Register */
|
|
#define UART_IIR 2 /* In: Interrupt ID Register */
|
|
#define UART_FCR 2 /* Out: FIFO Control Register */
|
|
#define UART_EFR 2 /* I/O: Extended Features Register */
|
|
/* (DLAB=1, 16C660 only) */
|
|
#define UART_LCR 3 /* Out: Line Control Register */
|
|
#define UART_MCR 4 /* Out: Modem Control Register */
|
|
#define UART_LSR 5 /* In: Line Status Register */
|
|
#define UART_MSR 6 /* In: Modem Status Register */
|
|
#define UART_SCR 7 /* I/O: Scratch Register */
|
|
#else
|
|
|
|
#define UART_RX 0 /* In: Receive buffer (DLAB=0) */
|
|
#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */
|
|
#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
|
|
#define UART_DLM 4 /* Out: Divisor Latch High (DLAB=1) */
|
|
#define UART_IER 4 /* Out: Interrupt Enable Register */
|
|
#define UART_IIR 8 /* In: Interrupt ID Register */
|
|
#define UART_FCR 8 /* Out: FIFO Control Register */
|
|
#define UART_EFR 8 /* I/O: Extended Features Register */
|
|
/* (DLAB=1, 16C660 only) */
|
|
#define UART_LCR 12 /* Out: Line Control Register */
|
|
#define UART_MCR 12 /* Out: Modem Control Register */
|
|
#define UART_LSR 20 /* In: Line Status Register */
|
|
#define UART_MSR 24 /* In: Modem Status Register */
|
|
#define UART_SCR 28 /* I/O: Scratch Register */
|
|
#endif
|
|
|
|
/*
|
|
* These are the definitions for the FIFO Control Register
|
|
* (16650 only)
|
|
*/
|
|
#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
|
|
#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
|
|
#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
|
|
#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
|
|
#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
|
|
#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
|
|
#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
|
|
#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
|
|
#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
|
|
/* 16650 redefinitions */
|
|
#define UART_FCR6_R_TRIGGER_8 0x00 /* Mask for receive trigger set at 1 */
|
|
#define UART_FCR6_R_TRIGGER_16 0x40 /* Mask for receive trigger set at 4 */
|
|
#define UART_FCR6_R_TRIGGER_24 0x80 /* Mask for receive trigger set at 8 */
|
|
#define UART_FCR6_R_TRIGGER_28 0xC0 /* Mask for receive trigger set at 14 */
|
|
#define UART_FCR6_T_TRIGGER_16 0x00 /* Mask for transmit trigger set at 16 */
|
|
#define UART_FCR6_T_TRIGGER_8 0x10 /* Mask for transmit trigger set at 8 */
|
|
#define UART_FCR6_T_TRIGGER_24 0x20 /* Mask for transmit trigger set at 24 */
|
|
#define UART_FCR6_T_TRIGGER_30 0x30 /* Mask for transmit trigger set at 30 */
|
|
|
|
/*
|
|
* These are the definitions for the Line Control Register
|
|
*
|
|
* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
|
|
* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
|
|
*/
|
|
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
|
|
#define UART_LCR_SBC 0x40 /* Set break control */
|
|
#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
|
|
#define UART_LCR_EPAR 0x10 /* Even parity select */
|
|
#define UART_LCR_PARITY 0x08 /* Parity Enable */
|
|
#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
|
|
#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
|
|
#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
|
|
#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
|
|
#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
|
|
|
|
/*
|
|
* These are the definitions for the Line Status Register
|
|
*/
|
|
#define UART_LSR_TEMT 0x40 /* Transmitter empty */
|
|
#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
|
|
#define UART_LSR_BI 0x10 /* Break interrupt indicator */
|
|
#define UART_LSR_FE 0x08 /* Frame error indicator */
|
|
#define UART_LSR_PE 0x04 /* Parity error indicator */
|
|
#define UART_LSR_OE 0x02 /* Overrun error indicator */
|
|
#define UART_LSR_DR 0x01 /* Receiver data ready */
|
|
|
|
/*
|
|
* These are the definitions for the Interrupt Identification Register
|
|
*/
|
|
#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
|
|
#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
|
|
|
|
#define UART_IIR_MSI 0x00 /* Modem status interrupt */
|
|
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
|
|
#define UART_IIR_TOI 0x0c /* Receive time out interrupt */
|
|
#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
|
|
#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
|
|
|
|
/*
|
|
* These are the definitions for the Interrupt Enable Register
|
|
*/
|
|
#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
|
|
#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
|
|
#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
|
|
#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
|
|
|
|
/*
|
|
* These are the definitions for the Modem Control Register
|
|
*/
|
|
#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
|
|
#define UART_MCR_OUT2 0x08 /* Out2 complement */
|
|
#define UART_MCR_OUT1 0x04 /* Out1 complement */
|
|
#define UART_MCR_RTS 0x02 /* RTS complement */
|
|
#define UART_MCR_DTR 0x01 /* DTR complement */
|
|
|
|
/*
|
|
* These are the definitions for the Modem Status Register
|
|
*/
|
|
#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
|
|
#define UART_MSR_RI 0x40 /* Ring Indicator */
|
|
#define UART_MSR_DSR 0x20 /* Data Set Ready */
|
|
#define UART_MSR_CTS 0x10 /* Clear to Send */
|
|
#define UART_MSR_DDCD 0x08 /* Delta DCD */
|
|
#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
|
|
#define UART_MSR_DDSR 0x02 /* Delta DSR */
|
|
#define UART_MSR_DCTS 0x01 /* Delta CTS */
|
|
#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */
|
|
|
|
/*
|
|
* These are the definitions for the Extended Features Register
|
|
* (StarTech 16C660 only, when DLAB=1)
|
|
*/
|
|
#define UART_EFR_CTS 0x80 /* CTS flow control */
|
|
#define UART_EFR_RTS 0x40 /* RTS flow control */
|
|
#define UART_EFR_SCD 0x20 /* Special character detect */
|
|
#define UART_EFR_ENI 0x10 /* Enhanced Interrupt */
|
|
|
|
|
|
No newline at end of file
|
No newline at end of file
|
