Line 1... |
Line 1... |
$Id: README_known_issues.txt 680 2015-05-14 13:29:46Z mueller $
|
$Id: README_known_issues.txt 687 2015-06-05 09:03:34Z mueller $
|
|
|
Known issues for this release.
|
Known issues for this release.
|
The case id indicates the release when the issue was first recognized.
|
The case id indicates the release when the issue was first recognized.
|
|
|
|
- V0.66-1: the TM11 controller transfers data byte wise (all disk do it 16bit
|
|
word wise) and allows for odd byte length transfers. Odd length transfers
|
|
are currently not supported and rejected as invalid command. Odd byte
|
|
length records aren't used by OS, if at all, so in practice this limitation
|
|
isn't relevant.
|
|
- V0.66-2: using two RP06 drives in parallel under 211bsd leads to a hangup of
|
|
the system after a short time. Currently only operation of a single drive
|
|
works reliably.
|
|
|
- V0.65-1: ti_rri sometimes crashes in normal rundown (exit or ^D) when
|
- V0.65-1: ti_rri sometimes crashes in normal rundown (exit or ^D) when
|
a cuff: type rlink is active. One gets
|
a cuff: type rlink is active. One gets
|
terminate called after throwing an instance of 'Retro::Rexception'
|
terminate called after throwing an instance of 'Retro::Rexception'
|
what(): RlinkPortCuff::Cleanup(): driver thread failed to stop
|
what(): RlinkPortCuff::Cleanup(): driver thread failed to stop
|
doesn't affect normal operation, will be fixed in upcoming release.
|
doesn't affect normal operation, will be fixed in upcoming release.
|
Line 20... |
Line 29... |
explicitly IOB flops, thus timing well defined.
|
explicitly IOB flops, thus timing well defined.
|
- V0.64-5: w11a_tb_guide.txt covers only ISE based tests (see also V0.64-4).
|
- V0.64-5: w11a_tb_guide.txt covers only ISE based tests (see also V0.64-4).
|
- V0.64-4: No support for the Vivado simulator (xsim) yet. With ghdl only
|
- V0.64-4: No support for the Vivado simulator (xsim) yet. With ghdl only
|
functional simulations, post synthesis (_ssim) fails to compile.
|
functional simulations, post synthesis (_ssim) fails to compile.
|
- V0.64-3: Highest baud rate with basys3 and nexys4 is 10 MBaud. 10 MBaud is
|
- V0.64-3: Highest baud rate with basys3 and nexys4 is 10 MBaud. 10 MBaud is
|
not supported according to FTDI, but works. 12 MBaud in next release.
|
not supported according to FTDI, but works. 12 MBaud in an upcoming release.
|
- V0.64-2: rlink throughput on basys3/nexys4 limited by serial port stack
|
- V0.64-2: rlink throughput on basys3/nexys4 limited by serial port stack
|
round trip times. Will be overcome by libusb based custom driver.
|
round trip times. Will be overcome by libusb based custom driver.
|
- V0.64-1: The large default transfer size for disk accesses leads to bad
|
- V0.64-1: The large default transfer size for disk accesses leads to bad
|
throughput in the DL11 emulation for low speed links, like the
|
throughput in the DL11 emulation for low speed links, like the
|
460kBaud the S3board is limited too. Will be overcome by a DL11
|
460kBaud the S3board is limited too. Will be overcome by a DL11
|