URL
https://opencores.org/ocsvn/wbfmtx/wbfmtx/trunk
Subversion Repositories wbfmtx
[/] [wbfmtx/] [trunk/] [rtl/] [wbfmtxhack.v] - Rev 3
Go to most recent revision | Compare with Previous | Blame | View Log
/////////////////////////////////////////////////////////////////////////// // // Filename: wbfmtxhack.v // // Project: A Wishbone Controlled FM Transmitter Hack // // Purpose: This Hack is based off of two things: 1) the interface spec // of the WB controlled PWM audio device, and 2) a Raspberry Pi // Hack I was shown that converted the RPi PWM device into an FM // transmitter. So, the question is, can a GPIO pin be turned into an // FM transmitter that can be heard throughout the house? // // We'll try and do this properly: We'll use a Numerically Controlled // Oscillator to generate our signal, but only grab the top bit out of // that oscillator. We'll then send this bit to the GPIO pin (a.k.a. // antenna) to see if it can accomplish our goals. // // WB Control/Registers: // 1'b0: Next Sample // // The top bits of this 'next sample' will indicate the number // of clock ticks before we generate a need next sample interrupt. // If these top bits are zero, the sample rate will not be // adjusted. The value to set here is the value of the clock // rate divided by the desired sample rate. Hence, if the clock // rate is 80MHz, setting this to 10e3 (unsigned) would set us up // for an 8kHz sample rate, whereas setting these upper 16 bits to // 1814 would specify a sample rate closer to 44.1kHz. // // The lower 16 bits specify the value of the next sample. // // Since we'll be dealing with FM modulation, we'll try to arrange // that this sixteen bit sample will correspond to a maximum // FM deviation of about 75 kHz. // // // 1'b1: The Oscillator "Frequency" (really stepsize). This should be // used to control/determine the "RF frequency" this device can // transmit on. // // To transmit at 0Hz, set this to zero. To transmit at // CLKSPEED/2 Hz, set this to 32'h8000_0000. Hence for a // transmit frequency of X, set this value to // // OSXFREQ = 2^32 * X / CLKSPEED // // Where X and CLKSPEED share the same units. But how shall we // transmit at speeds of anything higher than CLKSPEED/2? By // aliasing up. Hence, set X to your actual frequency value, // divide by the clockspeed and multiply by 2^32. Remove any // bits that don't fit in the top 32 and you are there. // // This also gives us about 20 mHz resolution for our Carrier // frequency--overkill perhaps, but it should work. // // So ... how do we create our 75 kHz deviation? We want: // // MAX_STEPSIZE = 2^32 * (X + 75kHz * sample / 2^15) / CLKSPEED // = OSXFREQ = (2^32 * sample / 2^15 / CLKSPEED * 75 kHz) // = 123 * sample ~= 128 * sample = sample << 7. // // Thus, by shifting our input sample value a touch, we can multiply by // nearly the exact constant we want. // // Creator: Dan Gisselquist, Ph.D. // Gisselquist Technology, LLC // /////////////////////////////////////////////////////////////////////////// // // Copyright (C) 2015, Gisselquist Technology, LLC // // This program is free software (firmware): you can redistribute it and/or // modify it under the terms of the GNU General Public License as published // by the Free Software Foundation, either version 3 of the License, or (at // your option) any later version. // // This program is distributed in the hope that it will be useful, but WITHOUT // ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or // FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License // for more details. // // You should have received a copy of the GNU General Public License along // with this program. (It's in the $(ROOT)/doc directory. Run make with no // target there if the PDF file isn't present.) If not, see // <http://www.gnu.org/licenses/> for a copy. // // License: GPL, v3, as defined and found on www.gnu.org, // http://www.gnu.org/licenses/gpl.html // // /////////////////////////////////////////////////////////////////////////// module wbfmtxhack(i_clk, // Wishbone interface i_wb_cyc, i_wb_stb, i_wb_we, i_wb_addr, i_wb_data, o_wb_ack, o_wb_stall, o_wb_data, o_tx, o_int); parameter DEFAULT_RELOAD = 16'd1814; // 44.1kHz at a 80MHz clock input i_clk; input i_wb_cyc, i_wb_stb, i_wb_we; input i_wb_addr; input [31:0] i_wb_data; output reg o_wb_ack; output wire o_wb_stall; output reg [31:0] o_wb_data; output wire o_tx; output reg o_int; reg [31:0] nco_step, nco_phase; // How often shall we create an interrupt? Every reload_value clocks! // If VARIABLE_RATE==0, this value will never change and will be kept // at the default reload rate (44.1 kHz, for a 100 MHz clock) reg [15:0] reload_value; initial reload_value = DEFAULT_RELOAD; // Data write, but we use the upper 16 bits to set our sample rate. // If these bits are zero, we ignore the write--allowing users to // write samples without adjusting the sample rate. always @(posedge i_clk) // Set sample rate if ((i_wb_cyc)&&(i_wb_stb)&&(~i_wb_addr)&&(i_wb_we) &&(|i_wb_data[31:16])) reload_value <= i_wb_data[31:16]; // Set the NCO transmit frequency initial nco_step = 32'h00; always @(posedge i_clk) if ((i_wb_cyc)&&(i_wb_stb)&&(i_wb_addr)&&(i_wb_we)) nco_step <= i_wb_data[31:0]; reg ztimer; reg [15:0] timer; initial ztimer = 1'b0; always @(posedge i_clk) // Be true when the timer is zero ztimer <= (timer[15:0] == 16'h1); initial timer = reload_value; always @(posedge i_clk) if (ztimer) timer <= reload_value; else timer <= timer - 16'h1; reg [15:0] next_sample, sample_out; initial sample_out = 16'h00; initial next_sample = 16'h00; always @(posedge i_clk) if (ztimer) sample_out <= next_sample; reg next_valid; initial next_valid = 1'b1; initial next_sample = 16'h8000; always @(posedge i_clk) // Data write if ((i_wb_cyc)&&(i_wb_stb)&&(i_wb_we)&&(~i_wb_addr)) begin // Write with two's complement data next_sample <= i_wb_data[15:0]; next_valid <= 1'b1; end else if (ztimer) next_valid <= 1'b0; // The interrupt line will remain high until writing a new data value // clears it. This design does not permit turning off this interrupt. // If the interrupt needs to be turned off, then ignore it in the // interrupt controller. initial o_int = 1'b0; always @(posedge i_clk) o_int <= (~next_valid); // Adjust the gain for a maximum frequency offset just greater than // 75 kHz. (We would've done 75kHz exactly, but it required a multiply // and this doesn't.) initial nco_phase = 32'h00; always @(posedge i_clk) nco_phase <= nco_phase + nco_step + { {(32-16-7){sample_out[15]}}, sample_out, 7'h00 }; assign o_tx = nco_phase[31]; always @(posedge i_clk) if (i_wb_addr) o_wb_data <= nco_step; else o_wb_data <= { reload_value, sample_out[15:1], o_int }; initial o_wb_ack = 1'b0; always @(posedge i_clk) o_wb_ack <= (i_wb_cyc)&&(i_wb_stb); assign o_wb_stall = 1'b0; endmodule
Go to most recent revision | Compare with Previous | Blame | View Log