URL
https://opencores.org/ocsvn/System09/System09/trunk
Subversion Repositories System09
[/] [System09/] [trunk/] [rtl/] [System09_BurchED_B3/] [System09_BurchED_B3.vhd] - Rev 221
Go to most recent revision | Compare with Previous | Blame | View Log
--=============================================================================-- -- -- -- System09 - Synthesizable System On a Chip - VHDL FPGA core top level file. -- -- -- --=============================================================================-- -- -- File name : System09_BurchED_B3.vhd -- -- Purpose : This is the top level file for a 6809 instruction compatible system on a chip -- It has been designed for the BurchED B3 Spartan2+ FPGA board -- using the Xilinx XC2S200 Spartan 2 FPGA and Xilinx ISE 7.1 software. -- It has been implemented with the BurchED B3 FPGA board, -- modified B3-SRAM module and B3-FPGA-CPU-IO module. -- It also supports an IDE CF card interface using a CF to IDE interface adapter. -- It uses a monochrome version of the VDU due to limitted Block RAM of XC2S200 -- -- Dependencies : ieee.Std_Logic_1164 -- ieee.std_logic_unsigned -- ieee.std_logic_arith -- ieee.numeric_std -- -- Uses : -- clk_div (..\Spartan2\clk_div.vhd) System Clock Divider -- cpu09 (..\VHDL\cpu09.vhd) CPU core -- B3_SRAM (..\VHDL\B3_SRAM.vhd) BurchED B3 SRAM module interface -- acia6850 (..\VHDL\acia6850.vhd) RS232 Serial Interface -- ACIA_Clock (..\VHDL\ACIA_Clock.vhd) ACIA Baud Rate Clock Divider -- keyboard (..\VHDL\keyboard.vhd) PS/2 Keyboard register interface -- ps2_keyboard (..\VHDL\ps2_keyboard.vhd) PS/2 Keyboard interface logic -- keymap_rom (..\Spartan2\keymap_rom_b4.vhd) PS/2 Keyboard key code look up table -- vdu8_mono (..\VHDL\vdu8_mono.vhd) 80 x 25 Monochrome Visual Display Unit. -- char_rom (..\Spartan2\char_rom2k_b4.vhd) Character Generator ROM -- ram_2k (..\Spartan2\ram2k_b4.vhd) Text buffer RAM -- timer (..\VHDL\timer.vhd) Timer module -- trap (..\VHDL\trap.vhd) Bus Trap interrupt -- spp (..\VHDL\spp.vhd) Simple Parallel Port -- peripheral_bus (..\VHDL\peripheral_bus.vhd) 16 bit IDE Peripheral Bus interface -- sys09bug_F800 (..\Spartan2\sys09b3s_b4.vhd) Sysbug09 Monitor ROM -- dat_ram (..\VHDL\datram.vhd) Dynamic Address Translation (DAT) -- -- Author : John E. Kent -- dilbert57@opencores.org -- -- Memory Map : -- -- $0000 - $DFFF System RAM (256K Mapped via DAT) -- $E000 - ACIA (SWTPc) -- $E010 - Reserved for SWTPc FD-01 FD1771 FDC -- $E020 - Keyboard -- $E030 - VDU -- $E040 - Reserved for SWTPc MP-T (was Compact Flash) -- $E050 - Timer -- $E060 - Bus Trap (Hardware Breakpoint Interrupt Logic) -- $E070 - Reserved for Trace Buffer -- $E080 - Reserved for SWTPc MP-ID 6821 PIA (?) -- $E090 - Reserved for SWTPc MP-ID 6840 PTM (?) -- $E0A0 - SPP Printer Port -- $E0B0 - Reserved -- $E0C0 - Reserved -- $E100 - $E13F IDE / Compact Flash Card -- $E140 - $E17F Reserved for Ethernet MAC (XESS) -- $E180 - $E1BF Reserved for Expansion Slot 0 (XESS) -- $E1C0 - $E1FF Reserved for Expansion Slot 1 (XESS) -- $E200 - $EFFF Dual Port RAM interface -- $F000 - $F7FF Reserved SWTPc DMAF-2 -- $F800 - $FFFF Sys09bug ROM (Read only) -- $FFF0 - $FFFF DAT - Dynamic Address Translation (Write Only) -- -- -- Copyright (C) 2003 - 2010 John Kent -- -- This program is free software: you can redistribute it and/or modify -- it under the terms of the GNU General Public License as published by -- the Free Software Foundation, either version 3 of the License, or -- (at your option) any later version. -- -- This program is distributed in the hope that it will be useful, -- but WITHOUT ANY WARRANTY; without even the implied warranty of -- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -- GNU General Public License for more details. -- -- You should have received a copy of the GNU General Public License -- along with this program. If not, see <http://www.gnu.org/licenses/>. -- --===========================================================================-- -- -- Revision History: -- --===========================================================================-- -- Version 0.1 - 20 March 2003 -- Version 0.2 - 30 March 2003 -- Version 0.3 - 29 April 2003 -- Version 0.4 - 29 June 2003 -- -- Version 0.5 - 19 July 2003 -- prints out "Hello World" -- -- Version 0.6 - 5 September 2003 -- Runs SBUG -- -- Version 1.0- 6 Sep 2003 - John Kent -- Inverted SysClk -- Initial release to Open Cores -- -- Version 1.1 - 17 Jan 2004 - John Kent -- Updated miniUart. -- -- Version 1.2 - 25 Jan 2004 - John Kent -- removed signals "test_alu" and "test_cc" -- Trap hardware re-instated. -- -- Version 1.3 - 11 Feb 2004 - John Kent -- Designed forked off to produce System09_VDU -- Added VDU component -- VDU runs at 25MHz and divides the clock by 2 for the CPU -- UART Runs at 57.6 Kbps -- -- Version 1.4 - 21 Nov 2004 - John Kent -- Changes to make compatible with Spartan3 starter kit version -- Designed to run with a 50MHz clock input. -- the VDU divides 50 MHz to generate a -- 25 MHz VDU Pixel Clock and a 12.5 MHz CPU clock -- Changed Monitor ROM signals to make it look like -- a standard 2K memory block -- Re-assigned I/O port assignments so it is possible to run KBUG9 -- -- Version 1.5 - 3rd February 2007 - John Kent -- Changed VDU8 to use external clock divider -- renamed miniUART to ACIA_6850 -- Memory decoding of ROM & IO now uses DAT -- -- Version 1.6 - 7th Februaury 2007 - John Kent -- Made ACIA Clock generator an external component -- Added Generics to VDU and Keyboard -- Changed decoding -- -- Version 1.7 - 20th May 2007 - John Kent -- Added 4 wait states to CF access -- Removed DAT memory map control of ROM & IO -- to allow for full use of RAM as a RAM disk. -- Mapped in all 16 bits of the CF data bus. -- -- Version 1.8 - 1st July 2007 - John Kent -- Copied B5-X300 top level to B3 version. -- -- Version 2.0 - 6th September 2008 - John Kent -- added IDE interface for a CF card. -- Used separate Clock DLL for generating clocks -- -- Version 2.1 - 23rd Februaury 2008 - John Kent -- Renamed Monitor ROM -- -- Version 2.2 - 28th August 2010 - John Kent -- Renamed ACIA_6850 to acia6850 -- Updated CPU & VDU component signal names & generics -- Made peripheral bus interface a separate component -- Made BED_SRAM a separate component -- Made the LED flasher a separate component -- Updated Header -- --=========================================================================== -- library ieee; use ieee.std_logic_1164.all; use IEEE.STD_LOGIC_ARITH.ALL; use IEEE.STD_LOGIC_UNSIGNED.ALL; use ieee.numeric_std.all; library unisim; use unisim.vcomponents.all; entity System09 is port( clk_in : in Std_Logic; -- System Clock input rst_n : in Std_logic; -- Master Reset input (active low) LED : out Std_logic; -- Diagnostic LED Flasher -- B3-SRAM Memory Interface signals ram_csn : out Std_Logic; ram_wrln : out Std_Logic; ram_wrun : out Std_Logic; ram_addr : out Std_Logic_Vector(16 downto 0); ram_data : inout Std_Logic_Vector(15 downto 0); -- End of B3-SRAM Memory Interface signals -- B3-FPGA-CPU-IO Module signals -- Asychronous Communications Interface Adapater signals (RS232 Serial Port) ($E00X) acia_rxd : in Std_Logic; acia_txd : out Std_Logic; acia_rts_n : out Std_Logic; acia_cts_n : in Std_Logic; -- PS/2 Keyboard Interface ($E02X) kb_clock : inout Std_logic; kb_data : inout Std_Logic; -- PS/2 Mouse interface -- mouse_clock : in Std_Logic; -- mouse_data : in Std_Logic; -- Visual Display Unit output signals ($E03X) vga_vsync : out Std_Logic; vga_hsync : out Std_Logic; vga_blue : out std_logic_vector(1 downto 0); vga_green : out std_logic_vector(1 downto 0); vga_red : out std_logic_vector(1 downto 0); -- Buzzer -- buzzer : out std_logic; -- End of B3-FPGA-CPU-IO Module signals -- Parallel Printer Port ($E0AX) pp_data : out std_logic_vector(7 downto 0); pp_stat : in std_logic_vector(7 downto 3); pp_ctrl : out std_logic_vector(3 downto 0); -- Peripheral Bus ($E100 - $E1FF) pb_iord_n : out std_logic; pb_iowr_n : out std_logic; pb_addr : out std_logic_vector(2 downto 0); pb_data : inout std_logic_vector(15 downto 0); -- IDE Compact Flash ($E100 - $E13F) ide_rst_n : out std_logic; -- ide pin 1 ide_cs0_n : out std_logic; -- ide pin 37 ide_cs1_n : out std_logic; -- ide pin 38 ide_dmarq : in std_logic; -- ide pin 21 ide_dmack_n : out std_logic; -- ide pin 29 ide_iordy : in std_logic; -- ide pin 27 ide_con_csel : out std_logic; -- ide pin 28 ide_intrq : in std_logic; -- ide pin 31 ide_iocs16_n : in std_logic; -- ide pin 32 ide_pdiag_n : in std_logic; -- ide pin 34 ide_dasp_n : out std_logic; -- ide pin 39 -- Dual port RAM interface bus bus_clk : in std_logic; bus_cs_n : in std_logic; bus_rw : in std_logic; bus_addr : in std_logic_vector(12 downto 0); bus_data_in : in std_logic_vector(7 downto 0); bus_data_out : out std_logic_vector(7 downto 0) ); end System09; ------------------------------------------------------------------------------- -- Architecture for System09 ------------------------------------------------------------------------------- architecture rtl of System09 is ----------------------------------------------------------------------------- -- constants ----------------------------------------------------------------------------- constant SYS_CLK_FREQ : integer := 50000000; -- FPGA System Clock constant VGA_CLK_FREQ : integer := 25000000; -- VGA Pixel Clock constant CPU_CLK_FREQ : integer := 12500000; -- CPU Clock constant BAUD_RATE : integer := 57600; -- Baud Rate constant ACIA_CLK_FREQ : integer := BAUD_RATE * 16; ----------------------------------------------------------------------------- -- Signals ----------------------------------------------------------------------------- -- System Clock signal sys_clk : std_logic; -- CPU Interface signals signal cpu_rst : Std_Logic; signal cpu_clk : Std_Logic; signal cpu_rw : std_logic; signal cpu_vma : std_logic; signal cpu_halt : std_logic; signal cpu_hold : std_logic; signal cpu_firq : std_logic; signal cpu_irq : std_logic; signal cpu_nmi : std_logic; signal cpu_addr : std_logic_vector(15 downto 0); signal cpu_data_in : std_logic_vector(7 downto 0); signal cpu_data_out : std_logic_vector(7 downto 0); -- B3 Static RAM ($0000 - $DFFF) signal ram_cs : std_logic; -- memory chip select signal ram_data_out : std_logic_vector(7 downto 0); -- ACIA Console serial port ($E000 - $E00F) signal acia_data_out : Std_Logic_Vector(7 downto 0); signal acia_cs : Std_Logic; signal acia_irq : Std_Logic; signal acia_clk : Std_Logic; -- PS/2 Keyboard interface ($E02X) signal kbd_data_out : std_logic_vector(7 downto 0); signal kbd_cs : std_logic; signal kbd_irq : std_logic; -- Visual Display Unit ($E03X) signal vga_clk : std_logic; signal vdu_cs : std_logic; signal vdu_data_out : std_logic_vector(7 downto 0); signal vga_red_o : std_logic; signal vga_green_o : std_logic; signal vga_blue_o : std_logic; -- Timer ($E05X) signal timer_data_out : std_logic_vector(7 downto 0); signal timer_cs : std_logic; signal timer_irq : std_logic; -- Bus trap ($E06X) signal trap_cs : std_logic; signal trap_data_out : std_logic_vector(7 downto 0); signal trap_irq : std_logic; -- Trace ($E07X) -- signal trace_cs : std_logic; -- signal trace_data_out : std_logic_vector(7 downto 0); -- signal trace_irq : std_logic; -- Simple Parallel I/O port ($E0AX) signal spp_data_out : std_logic_vector(7 downto 0); signal spp_cs : std_logic; -- Peripheral Bus ($E1XX) signal pb_cs : std_logic; signal pb_data_out : std_logic_vector(7 downto 0); signal pb_hold : std_logic; -- Peripheral Bus Chip Selects ($E1XX) signal ide_cs : std_logic; -- IDE CF interface ($E100 - $E13F) signal ether_cs : std_logic; -- Ethernet interface ($E140 - $E17F) signal slot1_cs : std_logic; -- Expansion slot1 ($E180 - $E1BF) signal slot2_cs : std_logic; -- Expansion slot 2 ($E1C0 - $E1FF) -- Dual Port RAM for Bus Interfacing ($E200 - $E7FF) signal dpr_data_out : std_logic_vector(7 downto 0); signal dpr_cs : std_logic; signal dpr_wr : std_logic; -- External Bus Interface signal bus_iclk : std_logic; signal bus_gclk : std_logic; signal bus_cs : std_logic; signal bus_wr : std_logic; -- Monitor ROM ($F800 - $FFFF) signal rom_data_out : Std_Logic_Vector(7 downto 0); signal rom_cs : std_logic; -- Dynamic Address Translation ($FFF0 - $FFFF) signal dat_cs : std_logic; signal dat_addr : std_logic_vector(7 downto 0); ----------------------------------------------------------------- -- -- Clock generator -- ----------------------------------------------------------------- component clock_div port( clk_in : in std_Logic; -- System Clock input sys_clk : out std_logic; -- System Clock Out (1/1) vga_clk : out std_logic; -- VGA Pixel Clock Out (1/2) cpu_clk : out std_logic -- CPU Clock Out (1/4) ); end component; ----------------------------------------------------------------- -- -- LED Flasher -- ----------------------------------------------------------------- component flasher port ( clk : in std_logic; -- Clock input rst : in std_logic; -- Reset input (active high) LED : out Std_Logic -- LED output ); end component; ----------------------------------------------------------------- -- -- 6809 Compatible CPU core -- ----------------------------------------------------------------- component cpu09 port ( clk : in std_logic; rst : in std_logic; rw : out std_logic; vma : out std_logic; addr : out std_logic_vector(15 downto 0); data_in : in std_logic_vector(7 downto 0); data_out : out std_logic_vector(7 downto 0); halt : in std_logic; hold : in std_logic; irq : in std_logic; nmi : in std_logic; firq : in std_logic ); end component; ----------------------------------------------------------------- -- -- Dynamic Address Translation Registers ($FFF0 - $FFFF) -- ----------------------------------------------------------------- component dat_ram port ( clk : in std_logic; rst : in std_logic; cs : in std_logic; rw : in std_logic; addr_lo : in std_logic_vector(3 downto 0); addr_hi : in std_logic_vector(3 downto 0); data_in : in std_logic_vector(7 downto 0); data_out : out std_logic_vector(7 downto 0) ); end component; ------------------------------------------------- -- -- Sys09Bug Block RAM Monitor ROM ($F800-$FFFF) -- ------------------------------------------------- component sys09bug_F800 port ( clk : in std_logic; rst : in std_logic; cs : in std_logic; addr : in std_logic_vector (10 downto 0); rw : in std_logic; data_in : in std_logic_vector (7 downto 0); data_out : out std_logic_vector (7 downto 0) ); end component; ----------------------------------------------------------------- -- -- 6850 ACIA RS232 Interface ($E000 - $E00F) -- ----------------------------------------------------------------- component acia6850 port ( clk : in Std_Logic; -- System Clock rst : in Std_Logic; -- Reset input (active high) cs : in Std_Logic; -- miniUART Chip Select rw : in Std_Logic; -- Read / Not Write irq : out Std_Logic; -- Interrupt addr : in Std_Logic; -- Register Select data_in : in Std_Logic_Vector(7 downto 0); -- Data Bus In data_out : out Std_Logic_Vector(7 downto 0); -- Data Bus Out RxC : in Std_Logic; -- Receive Baud Clock TxC : in Std_Logic; -- Transmit Baud Clock RxD : in Std_Logic; -- Receive Data TxD : out Std_Logic; -- Transmit Data DCD_n : in Std_Logic; -- Data Carrier Detect CTS_n : in Std_Logic; -- Clear To Send RTS_n : out Std_Logic ); -- Request To send end component; ----------------------------------------------------------------- -- -- ACIA Clock divider -- ----------------------------------------------------------------- component ACIA_Clock generic ( SYS_CLK_FREQ : integer := SYS_CLK_FREQ; ACIA_CLK_FREQ : integer := ACIA_CLK_FREQ ); port ( clk : in Std_Logic; -- System Clock Input acia_clk : out Std_logic -- ACIA Clock output ); end component; ---------------------------------------- -- -- PS/2 Keyboard ($E020 - $E02F) -- ---------------------------------------- component keyboard generic( KBD_CLK_FREQ : integer := CPU_CLK_FREQ ); port ( clk : in std_logic; rst : in std_logic; cs : in std_logic; rw : in std_logic; addr : in std_logic; data_in : in std_logic_vector(7 downto 0); data_out : out std_logic_vector(7 downto 0); irq : out std_logic; kbd_clk : inout std_logic; kbd_data : inout std_logic ); end component; ---------------------------------------- -- -- Video Display Unit. ($E030 - $E03F) -- ---------------------------------------- component vdu8_mono generic( VGA_CLK_FREQ : integer := VGA_CLK_FREQ; -- HZ VGA_HOR_CHARS : integer := 80; -- CHARACTERS 25.6us VGA_HOR_CHAR_PIXELS : integer := 8; -- PIXELS 0.32us VGA_HOR_FRONT_PORCH : integer := 16; -- PIXELS 0.64us VGA_HOR_SYNC : integer := 96; -- PIXELS 3.84us VGA_HOR_BACK_PORCH : integer := 48; -- PIXELS 1.92us VGA_VER_CHARS : integer := 25; -- CHARACTERS 12.8ms VGA_VER_CHAR_LINES : integer := 16; -- LINES 0.512ms VGA_VER_FRONT_PORCH : integer := 10; -- LINES 0.320ms VGA_VER_SYNC : integer := 2; -- LINES 0.064ms VGA_VER_BACK_PORCH : integer := 34 -- LINES 1.088ms ); port( -- control register interface vdu_clk : in std_logic; -- CPU Clock - 12.5MHz vdu_rst : in std_logic; vdu_cs : in std_logic; vdu_addr : in std_logic_vector(2 downto 0); vdu_rw : in std_logic; vdu_data_in : in std_logic_vector(7 downto 0); vdu_data_out : out std_logic_vector(7 downto 0); -- vga port connections vga_clk : in std_logic; -- VGA Pixel Clock - 25 MHz vga_red_o : out std_logic; vga_green_o : out std_logic; vga_blue_o : out std_logic; vga_hsync_o : out std_logic; vga_vsync_o : out std_logic ); end component; ---------------------------------------- -- -- Timer module ($E050 - $E05F) -- ---------------------------------------- component timer port ( clk : in std_logic; rst : in std_logic; cs : in std_logic; addr : in std_logic; rw : in std_logic; data_in : in std_logic_vector(7 downto 0); data_out : out std_logic_vector(7 downto 0); irq : out std_logic ); end component; ------------------------------------------------------------ -- -- Bus Trap / Hardware Breakpoint ($E060 - $E06F) -- ------------------------------------------------------------ component trap port ( clk : in std_logic; rst : in std_logic; cs : in std_logic; rw : in std_logic; vma : in std_logic; addr : in std_logic_vector(15 downto 0); data_in : in std_logic_vector(7 downto 0); data_out : out std_logic_vector(7 downto 0); irq : out std_logic ); end component; ------------------------------------------------------------ -- -- Bus Trace logic ($E070 - $E07F) -- ------------------------------------------------------------ --component trace is -- port ( -- clk : in std_logic; -- rst : in std_logic; -- rs : in std_logic; -- register select -- bs : in std_logic; -- bank select -- rw : in std_logic; -- vma : in std_logic; -- addr : in std_logic_vector(15 downto 0); -- data_in : in std_logic_vector(7 downto 0); -- reg_data_out : out std_logic_vector(7 downto 0); -- buff_data_out : out std_logic_vector(7 downto 0); -- cpu_data_in : in std_logic_vector(7 downto 0); -- irq : out std_logic -- ); --end component; ---------------------------------------- -- -- Simple Parallel Port ($E0A0 - $E0AF) -- ---------------------------------------- component spp port ( clk : in std_logic; rst : in std_logic; cs : in std_logic; addr : in std_logic_vector(2 downto 0); rw : in std_logic; data_in : in std_logic_vector(7 downto 0); data_out : out std_logic_vector(7 downto 0); irq : out std_logic; hold : out std_logic; spp_data : out std_logic_vector(7 downto 0); spp_stat : in std_logic_vector(7 downto 3); spp_ctrl : out std_logic_vector(3 downto 0) ); end component; ------------------------------------------------------------ -- -- Peripheral Bus interface (IDE CF) ($E100 - $E1FF) -- ------------------------------------------------------------ component peripheral_bus is port ( -- -- CPU Interface signals -- clk : in std_logic; -- System Clock rst : in std_logic; -- Reset input (active high) cs : in std_logic; -- Peripheral Bus Chip Select addr : in std_logic_vector(7 downto 0); -- Register Select rw : in std_logic; -- Read / Not Write data_in : in std_logic_vector(7 downto 0); -- Data Bus In data_out : out std_logic_vector(7 downto 0); -- Data Bus Out hold : out std_logic; -- Hold bus cycle output -- -- Peripheral Bus Interface Signals -- IO + ($00 - $FF) -- (for compatibility with XSA-3S1000 / XST 3.0) -- pb_rd_n : out std_logic; -- ide pin 25 pb_wr_n : out std_logic; -- ide pin 23 pb_addr : out std_logic_vector( 4 downto 0); pb_data : inout std_logic_vector(15 downto 0); -- Peripheral chip selects on Peripheral Bus ide_cs : out std_logic; -- IDE / CF interface ($00 - $3F) eth_cs : out std_logic; -- Ethernet interface ($40 - $7F) sl1_cs : out std_logic; -- Expansion slot 1 ($80 - $BF) sl2_cs : out std_logic -- Expansion slot 2 ($C0 - $FF) ); end component; ------------------------------------------------------------ -- -- External Bus interface Dual port RAM ($E200 - $EFFF) -- ------------------------------------------------------------ component RAMB4_S8_S8 port ( RSTA: IN std_logic; CLKA: IN std_logic; ENA: IN std_logic; WEA: IN std_logic; ADDRA: IN std_logic_vector(8 downto 0); DIA: IN std_logic_vector(7 downto 0); DOA: OUT std_logic_vector(7 downto 0); RSTB: IN std_logic; CLKB: IN std_logic; ENB: IN std_logic; WEB: IN std_logic; ADDRB: IN std_logic_vector(8 downto 0); DIB: IN std_logic_vector(7 downto 0); DOB: OUT std_logic_vector(7 downto 0) ); end component; component IBUF port ( I : IN std_logic; O : OUT std_logic ); end component; component BUFG port ( I : IN std_logic; O : OUT std_logic ); end component; ------------------------------------------------------------ -- -- BED SRAM interface ($0000 - $DFFF) -- ------------------------------------------------------------ component BED_SRAM port ( -- -- CPU Interface signals -- clk : in std_logic; -- System Clock (twice the CPU clock) rst : in std_logic; -- Reset input (active high) cs : in std_logic; -- RAM Chip Select addr : in std_logic_vector(17 downto 0); -- RAM address bus rw : in std_logic; -- Read / Not Write data_in : in std_logic_vector(7 downto 0); -- Data Bus In data_out : out std_logic_vector(7 downto 0); -- Data Bus Out -- -- B3_SRAM Interface Signals -- ram_csn : out Std_Logic; ram_wrln : out Std_Logic; ram_wrun : out Std_Logic; ram_addr : out Std_Logic_Vector(16 downto 0); ram_data : inout Std_Logic_Vector(15 downto 0) ); end component; begin ----------------------------------------------------------------------------- -- Instantiation of internal components ----------------------------------------------------------------------------- ---------------------------------------- -- -- Clock generator -- ---------------------------------------- my_clock_div: clock_div port map ( clk_in => clk_in, -- Clock input sys_clk => sys_clk, -- System Clock Out (1/1) vga_clk => vga_clk, -- VGA Pixel Clock Out (1/2) cpu_clk => cpu_clk -- CPU Clock Out (1/4) ); ----------------------------------------- -- -- LED Flasher -- ----------------------------------------- my_LED_flasher : flasher port map ( clk => cpu_clk, rst => cpu_rst, LED => LED ); ---------------------------------------- -- -- CPU09 CPU Core -- ---------------------------------------- my_cpu : cpu09 port map ( clk => cpu_clk, rst => cpu_rst, rw => cpu_rw, vma => cpu_vma, addr => cpu_addr(15 downto 0), data_in => cpu_data_in, data_out => cpu_data_out, halt => cpu_halt, hold => cpu_hold, irq => cpu_irq, nmi => cpu_nmi, firq => cpu_firq ); ---------------------------------------- -- -- Dynamic Address Translation ($FFF0-$FFFF) -- ---------------------------------------- my_dat : dat_ram port map ( clk => cpu_clk, rst => cpu_rst, cs => dat_cs, rw => cpu_rw, addr_hi => cpu_addr(15 downto 12), addr_lo => cpu_addr(3 downto 0), data_in => cpu_data_out, data_out => dat_addr(7 downto 0) ); ---------------------------------------- -- -- SYS09BUG Monitor ROM ($F800-$FFFF) -- ---------------------------------------- my_rom : SYS09BUG_F800 port map ( clk => cpu_clk, rst => cpu_rst, cs => rom_cs, rw => '1', addr => cpu_addr(10 downto 0), data_in => cpu_data_out, data_out => rom_data_out ); ---------------------------------------- -- -- ACIA RS232 Serial interface ($E000-$E00F) -- ---------------------------------------- my_ACIA : acia6850 port map ( -- -- CPU Interface -- clk => cpu_clk, rst => cpu_rst, cs => acia_cs, rw => cpu_rw, irq => acia_irq, addr => cpu_addr(0), data_in => cpu_data_out, data_out => acia_data_out, -- -- RS232 Interface -- RxC => acia_clk, TxC => acia_clk, RxD => acia_rxd, TxD => acia_txd, DCD_n => '0', CTS_n => acia_cts_n, RTS_n => acia_rts_n ); ---------------------------------------- -- -- ACIA Baud Clock -- ---------------------------------------- my_ACIA_Clock : ACIA_Clock generic map( SYS_CLK_FREQ => SYS_CLK_FREQ, ACIA_CLK_FREQ => ACIA_CLK_FREQ ) port map( clk => sys_clk, acia_clk => acia_clk ); ---------------------------------------- -- -- PS/2 Keyboard Interface ($E020-$E02F) -- ---------------------------------------- my_keyboard : keyboard generic map ( KBD_CLK_FREQ => CPU_CLK_FREQ ) port map( clk => cpu_clk, rst => cpu_rst, cs => kbd_cs, rw => cpu_rw, addr => cpu_addr(0), data_in => cpu_data_out(7 downto 0), data_out => kbd_data_out(7 downto 0), irq => kbd_irq, kbd_clk => kb_clock, kbd_data => kb_data ); ------------------------------------------------ -- -- Video Display Unit instantiation ($E030-$E03F) -- ------------------------------------------------- my_vdu : vdu8_mono generic map( VGA_CLK_FREQ => VGA_CLK_FREQ, -- 25MHZ VGA_HOR_CHARS => 80, -- CHARACTERS 25.6us VGA_HOR_CHAR_PIXELS => 8, -- PIXELS 0.32us VGA_HOR_FRONT_PORCH => 16, -- PIXELS 0.64us VGA_HOR_SYNC => 96, -- PIXELS 3.84us VGA_HOR_BACK_PORCH => 48, -- PIXELS 1.92us VGA_VER_CHARS => 25, -- CHARACTERS 12.8ms VGA_VER_CHAR_LINES => 16, -- LINES 0.512ms VGA_VER_FRONT_PORCH => 10, -- LINES 0.320ms VGA_VER_SYNC => 2, -- LINES 0.064ms VGA_VER_BACK_PORCH => 34 -- LINES 1.088ms ) port map( -- CPU Control Registers interface vdu_clk => cpu_clk, -- 12.5 MHz System Clock in vdu_rst => cpu_rst, vdu_cs => vdu_cs, vdu_rw => cpu_rw, vdu_addr => cpu_addr(2 downto 0), vdu_data_in => cpu_data_out, vdu_data_out => vdu_data_out, -- vga port connections vga_clk => vga_clk, -- 25 MHz VDU pixel clock vga_red_o => vga_red_o, vga_green_o => vga_green_o, vga_blue_o => vga_blue_o, vga_hsync_o => vga_hsync, vga_vsync_o => vga_vsync ); ---------------------------------------- -- -- Timer Module -- ---------------------------------------- my_timer : timer port map ( clk => cpu_clk, rst => cpu_rst, cs => timer_cs, rw => cpu_rw, addr => cpu_addr(0), data_in => cpu_data_out, data_out => timer_data_out, irq => timer_irq ); ---------------------------------------- -- -- Bus Trap Interrupt logic -- ---------------------------------------- my_trap : trap port map ( clk => cpu_clk, rst => cpu_rst, cs => trap_cs, rw => cpu_rw, vma => cpu_vma, addr => cpu_addr, data_in => cpu_data_out, data_out => trap_data_out, irq => trap_irq ); ---------------------------------------- -- -- Bus Trace logic -- ---------------------------------------- --my_trace : trace port map ( -- clk => sys_clk, -- rst => cpu_rst, -- rs => trace_cs, -- bs => bank_cs, -- rw => cpu_rw, -- vma => cpu_vma, -- addr => cpu_addr, -- data_in => cpu_data_out, -- reg_data_out => trace_data_out, -- buff_data_out => bank_data_out, -- cpu_data_in => cpu_data_in, -- irq => trace_irq -- ); ---------------------------------------- -- -- Simple Parallel Port -- ---------------------------------------- my_spp : spp port map ( clk => cpu_clk, rst => cpu_rst, cs => spp_cs, rw => cpu_rw, addr => cpu_addr(2 downto 0), data_in => cpu_data_out, data_out => spp_data_out, spp_data => pp_data, spp_stat => pp_stat, spp_ctrl => pp_ctrl, hold => open, irq => open ); ------------------------------------------------ -- -- 16 bit Peripheral Bus interface ($E100-$E1FF) -- ------------------------------------------------ my_pb : peripheral_bus port map ( -- -- CPU Interface signals -- clk => cpu_clk, rst => cpu_rst, cs => pb_cs, addr => cpu_addr(7 downto 0), rw => cpu_rw, data_in => cpu_data_out, data_out => pb_data_out, hold => pb_hold, -- -- Peripheral Bus Interface Signals -- IO + ($00 - $FF) -- pb_rd_n => pb_iord_n, pb_wr_n => pb_iowr_n, pb_addr(2 downto 0) => pb_addr, pb_addr(4 downto 3) => open, pb_data => pb_data, -- Peripheral chip selects on Peripheral Bus ide_cs => ide_cs, eth_cs => ether_cs, sl1_cs => slot1_cs, sl2_cs => slot2_cs ); ------------------------------------------------------ -- -- External Bus interface Dual port RAM ($E200 - $EFFF) -- ------------------------------------------------------- my_dpr : RAMB4_S8_S8 port map ( RSTA => cpu_rst, CLKA => cpu_clk, ENA => dpr_cs, WEA => dpr_wr, ADDRA => cpu_addr(8 downto 0), DIA => cpu_data_out, DOA => dpr_data_out, RSTB => cpu_rst, CLKB => bus_gclk, ENB => bus_cs, WEB => bus_wr, ADDRB => bus_addr(8 downto 0), DIB => bus_data_in, DOB => bus_data_out ); my_dpr_ibuf : IBUF port map ( I => bus_clk, O => bus_iclk ); my_dpr_bufg : BUFG port map ( I => bus_iclk, O => bus_gclk ); ----------------------------------------------- -- -- BED SRAM interface (256KBytes) ($0000-$DFFF) -- ----------------------------------------------- my_bed_sram : BED_SRAM port map ( -- -- CPU Interface signals -- clk => vga_clk, -- VGA Clock (twice the CPU clock) rst => cpu_rst, -- Reset input (active high) cs => ram_cs, -- RAM Chip Select addr(17 downto 12) => dat_addr( 5 downto 0), -- High RAM address goes to the DAT addr(11 downto 0) => cpu_addr(11 downto 0), -- Low RAM address goes to the CPU rw => cpu_rw, -- Read / Not Write data_in => cpu_data_out, -- Data Bus In data_out => ram_data_out, -- Data Bus Out -- -- B3_SRAM Interface Signals -- ram_csn => ram_csn, ram_wrln => ram_wrln, ram_wrun => ram_wrun, ram_addr => ram_addr, ram_data => ram_data ); ---------------------------------------------------------------------- -- -- Process to decode memory map -- ---------------------------------------------------------------------- my_decoder: process( cpu_addr, cpu_rw, cpu_vma, dat_addr, rom_data_out, acia_data_out, kbd_data_out, vdu_data_out, timer_data_out, trap_data_out, spp_data_out, dpr_data_out, pb_data_out, ram_data_out ) begin cpu_data_in <= (others=>'0'); dat_cs <= '0'; rom_cs <= '0'; acia_cs <= '0'; kbd_cs <= '0'; vdu_cs <= '0'; timer_cs <= '0'; trap_cs <= '0'; spp_cs <= '0'; dpr_cs <= '0'; pb_cs <= '0'; ram_cs <= '0'; if cpu_addr( 15 downto 8 ) = "11111111" then -- -- Dynamic Address Translation $FFF0 - $FFFF -- cpu_data_in <= rom_data_out; dat_cs <= cpu_vma; -- write DAT rom_cs <= cpu_vma; -- read ROM elsif (dat_addr(3 downto 0) = "1111") and (cpu_addr(11) = '1') then -- $XF800 - $XFFFF -- -- Sys09Bug Monitor ROM $F000 - $FFFF -- cpu_data_in <= rom_data_out; rom_cs <= cpu_vma; elsif dat_addr(3 downto 0) = "1110" then -- $XE000 - $XEFFF -- -- IO Devices $E000 - $E7FF -- case cpu_addr(11 downto 8) is -- -- SWTPC peripherals from $E000 to $E0FF -- when "0000" => case cpu_addr(7 downto 4) is -- -- ACIA RS232 Console Port $E000 - $E00F -- when "0000" => -- $E000 cpu_data_in <= acia_data_out; acia_cs <= cpu_vma; -- -- Reserved -- Floppy Disk Controller port $E010 - $E01F -- when "0001" => -- $E010 null; -- -- Keyboard port $E020 - $E02F -- when "0010" => -- $E020 cpu_data_in <= kbd_data_out; kbd_cs <= cpu_vma; -- -- VDU port $E030 - $E03F -- when "0011" => -- $E030 cpu_data_in <= vdu_data_out; vdu_cs <= cpu_vma; -- -- Reserved SWTPc MP-T Timer $E040 - $E04F -- when "0100" => -- $E040 cpu_data_in <= (others=> '0'); -- -- Timer $E050 - $E05F -- when "0101" => -- $E050 cpu_data_in <= timer_data_out; timer_cs <= cpu_vma; -- -- Bus Trap Logic $E060 - $E06F -- when "0110" => -- $E060 cpu_data_in <= trap_data_out; trap_cs <= cpu_vma; -- -- Bus Trace Logic $E070 - $E07F -- -- when "0111" => -- $E070 -- cpu_data_in <= trace_data_out; -- trace_cs <= cpu_vma; -- -- Reserved SWTPc MP-ID PIA Timer/Printer Port $E080 - $E08F -- when "1000" => -- $E080 null; -- -- Reserved SWTPc MP-ID PTM 6840 Timer Port $E090 - $E09F -- -- -- Simple Parallel Port $E0A0 - $E0AF -- when "1010" => -- $E0A0 cpu_data_in <= spp_data_out; spp_cs <= cpu_vma; -- -- Remaining 5 slots reserved for non SWTPc Peripherals -- when others => -- $E0B0 to $E0FF cpu_data_in <= (others=> '0'); end case; -- -- XST-3.0 Peripheral Bus goes here -- $E100 to $E1FF -- Four devices -- IDE, Ethernet, Slot1, Slot2 -- when "0001" => cpu_data_in <= pb_data_out; pb_cs <= cpu_vma; -- -- $E200 to $EFFF reserved for future use -- when others => cpu_data_in <= dpr_data_out; dpr_cs <= cpu_vma; end case; -- -- Flex RAM $0C000 - $0DFFF -- -- elsif dat_addr(7 downto 1) = "0000110" then -- $0C000 - $0DFFF -- cpu_data_in <= flex_data_out; -- flex_cs <= cpu_vma; -- -- Everything else is RAM -- else cpu_data_in <= ram_data_out; ram_cs <= cpu_vma; end if; end process; -- -- IDE drive / CF card signals ($E100 - $E13F) -- Located on peripheral bus -- ide_bus: process( cpu_rst, cpu_addr, ide_cs ) begin ide_cs0_n <= not( ide_cs ) or cpu_addr(4); ide_cs1_n <= not( ide_cs and cpu_addr(4)); ide_dmack_n <= '1'; ide_rst_n <= not cpu_rst; ide_con_csel <= '0'; ide_dasp_n <= not ide_cs; end process; -- -- Assign CPU interface signals -- cpu_controls : process( rst_n, pb_hold, acia_irq, kbd_irq, trap_irq, timer_irq ) begin cpu_rst <= not rst_n; -- CPU reset is active high cpu_irq <= acia_irq or kbd_irq; cpu_nmi <= trap_irq; cpu_firq <= timer_irq; cpu_halt <= '0'; cpu_hold <= pb_hold; end process; -- -- Assign DPR bus interface signals -- my_dpr_bus : process( bus_cs_n, bus_rw, cpu_rw ) begin bus_cs <= not bus_cs_n; bus_wr <= not bus_rw; dpr_wr <= not cpu_rw; -- trace_data_out <= (others=>'0'); end process; -- -- Assign VDU VGA output signals -- only 8 colours are handled. -- my_vga_out: process( vga_red_o, vga_green_o, vga_blue_o ) begin vga_red(0) <= vga_red_o; vga_red(1) <= vga_red_o; vga_green(0) <= vga_green_o; vga_green(1) <= vga_green_o; vga_blue(0) <= vga_blue_o; vga_blue(1) <= vga_blue_o; end process; end rtl; --===================== End of architecture =======================--
Go to most recent revision | Compare with Previous | Blame | View Log