URL
https://opencores.org/ocsvn/System09/System09/trunk
Subversion Repositories System09
[/] [System09/] [trunk/] [rtl/] [VHDL/] [datram.vhd] - Rev 159
Go to most recent revision | Compare with Previous | Blame | View Log
--===========================================================================-- -- -- -- Synthesizable SWTPc 6809 Dynamic Address Translation Table -- -- -- --===========================================================================-- -- -- File name : datram.vhd -- -- Entity name : dat_ram -- -- Purpose : Implements a Dynamic Address Translation RAM module -- as found in the SWTPc MP-09 CPU card. -- Maps the high order 4 address bits to 8 address lines -- extending the memory addressing range from 64K to 1MByte -- Memory segments are mapped on 4 KByte boundaries -- The DAT registers are mapped at the the top of memory -- ($FFF0 - $FFFF) and are write only so can map behind ROM. -- Since the DAT is not supported by SWTBUG for the 6800, -- the resgisters reset state map the bottom 64K of RAM. -- -- Dependencies : ieee.std_logic_1164 -- ieee.std_logic_unsigned -- unisim.vcomponents -- -- Author : John E. Kent -- -- Email : dilbert57@opencores.org -- -- Web : http://opencores.org/project,system09 -- -- Description : -- -- DAT is initializedas follows: -- -- DAT Dat Logical Physical -- Reg Val Addr Addr -- fff0 - 0f - page 0 - $0xxx = $00xxx (RAM) -- fff1 - 0e - page 1 - $1xxx = $01xxx (RAM) -- fff2 - 0d - page 2 - $2xxx = $02xxx (RAM) -- fff3 - 0c - page 3 - $3xxx = $03xxx (RAM) -- fff4 - 0b - page 4 - $4xxx = $04xxx (RAM) -- fff5 - 0a - page 5 - $5xxx = $05xxx (RAM) -- fff6 - 09 - page 6 - $6xxx = $06xxx (RAM) -- fff7 - 08 - page 7 - $7xxx = $07xxx (RAM) -- fff8 - 07 - page 8 - $8xxx = $08xxx (RAM) -- fff9 - 06 - page 9 - $9xxx = $09xxx (RAM) -- fffa - 05 - page A - $axxx = $0axxx (RAM) -- fffb - 04 - page B - $bxxx = $0bxxx (RAM) -- fffc - 03 - page C - $cxxx = $0cxxx (RAM) -- fffd - 02 - page D - $dxxx = $0dxxx (RAM) -- fffe - f1 - page E - $exxx = $fexxx (I/O) -- ffff - f0 - page F - $fxxx = $ffxxx (ROM/DMFA2) -- -- Copyright (C) 2003 - 2010 John Kent -- -- This program is free software: you can redistribute it and/or modify -- it under the terms of the GNU General Public License as published by -- the Free Software Foundation, either version 3 of the License, or -- (at your option) any later version. -- -- This program is distributed in the hope that it will be useful, -- but WITHOUT ANY WARRANTY; without even the implied warranty of -- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -- GNU General Public License for more details. -- -- You should have received a copy of the GNU General Public License -- along with this program. If not, see <http://www.gnu.org/licenses/>. -- --===========================================================================-- -- -- -- Revision History -- -- -- --===========================================================================-- -- -- Version Date Author Changes -- -- 0.1 2002-11-10 John Kent Initial version -- -- 0.2 2006-11-21 John Kent Inverted bottom 4 bits of dat_addr -- so that it is compatible with SWTPc MP-09 card. -- -- 0.3 2007-02-25 John Kent Modify the sensitivity lists -- -- 0.4 2010-06-17 John Kent Update header and added GPL -- -- 0.5 2010-12-10 John Kent Correction of pages in header documentation -- library ieee; use ieee.std_logic_1164.all; use ieee.std_logic_unsigned.all; --library unisim; -- use unisim.vcomponents.all; entity dat_ram is port ( clk : in std_logic; rst : in std_logic; cs : in std_logic; addr_hi : in std_logic_vector(3 downto 0); addr_lo : in std_logic_vector(3 downto 0); rw : in std_logic; data_in : in std_logic_vector(7 downto 0); data_out : out std_logic_vector(7 downto 0)); end dat_ram; architecture rtl of dat_ram is signal dat_reg0 : std_logic_vector(7 downto 0); signal dat_reg1 : std_logic_vector(7 downto 0); signal dat_reg2 : std_logic_vector(7 downto 0); signal dat_reg3 : std_logic_vector(7 downto 0); signal dat_reg4 : std_logic_vector(7 downto 0); signal dat_reg5 : std_logic_vector(7 downto 0); signal dat_reg6 : std_logic_vector(7 downto 0); signal dat_reg7 : std_logic_vector(7 downto 0); signal dat_reg8 : std_logic_vector(7 downto 0); signal dat_reg9 : std_logic_vector(7 downto 0); signal dat_reg10 : std_logic_vector(7 downto 0); signal dat_reg11 : std_logic_vector(7 downto 0); signal dat_reg12 : std_logic_vector(7 downto 0); signal dat_reg13 : std_logic_vector(7 downto 0); signal dat_reg14 : std_logic_vector(7 downto 0); signal dat_reg15 : std_logic_vector(7 downto 0); begin --------------------------------- -- -- Write DAT RAM -- --------------------------------- --dat_write : process( clk, rst, addr_lo, cs, rw, data_in ) dat_write : process( clk ) begin if clk'event and clk = '0' then if rst = '1' then dat_reg0 <= "00001111"; dat_reg1 <= "00001110"; dat_reg2 <= "00001101"; dat_reg3 <= "00001100"; dat_reg4 <= "00001011"; dat_reg5 <= "00001010"; dat_reg6 <= "00001001"; dat_reg7 <= "00001000"; dat_reg8 <= "00000111"; dat_reg9 <= "00000110"; dat_reg10 <= "00000101"; dat_reg11 <= "00000100"; dat_reg12 <= "00000011"; dat_reg13 <= "00000010"; dat_reg14 <= "11110001"; dat_reg15 <= "11110000"; else if cs = '1' and rw = '0' then case addr_lo is when "0000" => dat_reg0 <= data_in; when "0001" => dat_reg1 <= data_in; when "0010" => dat_reg2 <= data_in; when "0011" => dat_reg3 <= data_in; when "0100" => dat_reg4 <= data_in; when "0101" => dat_reg5 <= data_in; when "0110" => dat_reg6 <= data_in; when "0111" => dat_reg7 <= data_in; when "1000" => dat_reg8 <= data_in; when "1001" => dat_reg9 <= data_in; when "1010" => dat_reg10 <= data_in; when "1011" => dat_reg11 <= data_in; when "1100" => dat_reg12 <= data_in; when "1101" => dat_reg13 <= data_in; when "1110" => dat_reg14 <= data_in; when "1111" => dat_reg15 <= data_in; when others => null; end case; end if; end if; end if; end process; dat_read : process( addr_hi, dat_reg0, dat_reg1, dat_reg2, dat_reg3, dat_reg4, dat_reg5, dat_reg6, dat_reg7, dat_reg8, dat_reg9, dat_reg10, dat_reg11, dat_reg12, dat_reg13, dat_reg14, dat_reg15 ) variable phy_addr : std_logic_vector( 7 downto 0 ); begin case addr_hi is when "0000" => phy_addr := dat_reg0; when "0001" => phy_addr := dat_reg1; when "0010" => phy_addr := dat_reg2; when "0011" => phy_addr := dat_reg3; when "0100" => phy_addr := dat_reg4; when "0101" => phy_addr := dat_reg5; when "0110" => phy_addr := dat_reg6; when "0111" => phy_addr := dat_reg7; when "1000" => phy_addr := dat_reg8; when "1001" => phy_addr := dat_reg9; when "1010" => phy_addr := dat_reg10; when "1011" => phy_addr := dat_reg11; when "1100" => phy_addr := dat_reg12; when "1101" => phy_addr := dat_reg13; when "1110" => phy_addr := dat_reg14; when "1111" => phy_addr := dat_reg15; when others => null; end case; data_out( 7 downto 4 ) <= phy_addr( 7 downto 4 ); data_out( 3 downto 0 ) <= not( phy_addr( 3 downto 0 ) ); end process; end rtl;
Go to most recent revision | Compare with Previous | Blame | View Log