URL
https://opencores.org/ocsvn/System09/System09/trunk
Subversion Repositories System09
[/] [System09/] [trunk/] [src/] [upld/] [upld_cf8.asm] - Rev 171
Go to most recent revision | Compare with Previous | Blame | View Log
*
** FLEX 9 DISK DRIVERS
*
* FOR SYS09BUG ON THE DIGILENT SPARTAN 3 STARTER BOARD
* WITH I/O MAPPED AT $XE000
* AND ROM MAPPED AT $XF000
* THE DIGILENT SPARTAN 3 STARTER BOARD HAS 1MBYTE OF SRAM
* THE FIRST 64K IS USED BY FLEX,
* THE SECOND 128K IS USED AS A ROM DISK
* THE REMAINING RAM IS USED FOR A RAM DISK
*
*
CFLAG EQU $01 CARRY FLAG
VFLAG EQU $02 OVERFLOW FLAG
ZFLAG EQU $04 ZERO FLAG
NFLAG EQU $08 NEGATIVE FLAG
IFLAG EQU $10 IRQ MASK CC
HFLAG EQU $20 HALF CARRY
FFLAG EQU $40 FIRQ MASK CC
EFLAG EQU $80 ENTIRE FLAG
*
MAPPAG EQU $00 PAGE $0000 DAT ADDRESS
*
* Serial Port
*
ACIAS EQU $E000
ACIAC1 EQU ACIAS
ACIAD1 EQU ACIAS+1
DELCON EQU 1250 Delay (Processor clock in MHz * 50)
*
* XMODEM Control characters
*
SOH EQU $01
EOT EQU $04
ACK EQU $06
NAK EQU $15
CAN EQU $18
*
* Some dummy Constants
*
RMAXTRK EQU 48
RMAXSEC EQU 14
RTOTSEC EQU RMAXTRK*RMAXSEC-RMAXSEC
*
* Start
*
ORG $0100
START LBSR UXSUB
JMP [$F800] Jump to monitor on Completion.
*
*
* RAM SPACE
*
DRVNUM FCB 0
TRACK FCB 0
SECTOR FCB 0
CHKSUM FCB 0
BLKNUM FCB 0 Xmodem block number
BYTCNT FCB 0 Xmodem byte count
XSTATE FDB 0 Xmodem State Vector
DELCNT FCB $00,$00,$00 Xmodem Poll timer
MAXTRK FCB 0
MAXSEC FCB 0
ORG $0200
*
* SECTOR BUFFER
*
BUFFER RMB 256
*
* ACIA INPUT TEST
*
INTEST LDA ACIAC1
BITA #$01
RTS
*
* RESET ACIA
*
ACIRST LDA #$03 master reset
STA ACIAC1
LDA #$11
STA ACIAC1
RTS
*
* ACIA INPUT
*
INTER LDA #16
STA DELCNT+0
CLR DELCNT+1
CLR DELCNT+2
INTER0 LDA ACIAC1
BITA #$01
BNE INTER1
BITA #$78
BEQ INTER2
BSR ACIRST
BRA INTER
*
INTER1 LDA ACIAD1
ANDCC #$FF-VFLAG
RTS
*
INTER2 DEC DELCNT+2
BNE INTER0
DEC DELCNT+1
BNE INTER0
DEC DELCNT+0
BNE INTER0
CLRA
ORCC #VFLAG
RTS
*
* ACIA OUTPUT
*
OUTTER PSHS A
*
OUTTE1 LDA ACIAC1
BITA #$02
BNE OUTTE2
BITA #$78
BEQ OUTTE1
BSR ACIRST
BRA OUTTE1
*
OUTTE2 PULS A
STA ACIAD1
RTS
*
* Print Data
*
PDATA0 BSR OUTTER
PDATA1 LDA ,X+
CMPA #$04
BNE PDATA0
RTS
*
** 'UX' Xmodem ROM Disk upload
*
UXMES0 FCB $0D,$0A
FCC 'Xmodem ROM Disk Upload'
FCB 4
UXMES1 FCB $0D,$0A
FCC 'Upload Complete'
FCB 4
UXMES2 FCB $0D,$0A
FCC 'Upload Error'
FCB 4
UXMSG3 FCB $0D,$0A
FCC 'Drive Number :'
FCB 4
UXMSG4 FCB $0D,$0A
FCC 'Are You Sure ? (Y/N)'
FCB 4
*
* Print Banner
*
UXSUB LDX #UXMES0
LBSR PDATA1
*
* Prompt for Disk drive number (0 to 3)
*
LDX #UXMSG3
LBSR PDATA1
UXSUB1 LBSR INTER
BVS UXSUB1
LBSR OUTTER
CMPA #'0
LBLO UXEXIT
CMPA #'3
LBHI UXEXIT
SUBA #'0
STA DRVNUM
*
* Report selected drive
*
LDX #UXMSG3
LBSR PDATA1
LDA DRVNUM
ADDA #'0
LBSR OUTTER
*
* Ask for confirmation (Y/N)
*
LDX #UXMSG4
LBSR PDATA1
UXSUB2 LBSR INTER
BVS UXSUB2
LBSR OUTTER
ANDA #$5F
CMPA #'N
LBEQ UXEXIT
CMPA #'Y
BNE UXSUB
*
* We have confirmation ... now load the disk image
*
LBSR INITDR
LDU #XSTST
STU XSTATE
LDA #1
STA BLKNUM
*
* Sector1
*
LDX #BUFFER
*
CLRA TRACK 0
LDB #$01 SECTOR 1
STA TRACK
STB SECTOR
*
LBSR XREAD
LBCS UXERR
LBSR XACK
LBSR XREAD
LBCS UXERR
*
LDX #BUFFER
LDA TRACK
LDB SECTOR
LBSR WRITSC
LBSR XACK
*
* Sector 2
*
LDX #BUFFER
*
LDA TRACK
LDB SECTOR
INCB
STA TRACK
STB SECTOR
*
LBSR XREAD
LBCS UXERR
LBSR XACK
LBSR XREAD
LBCS UXERR
*
LDX #BUFFER
LDA TRACK
LDB SECTOR
LBSR WRITSC
*
LBSR XACK
*
* Sector 3 - SIR
*
LDX #BUFFER
*
LDA TRACK
LDB SECTOR
INCB
STA TRACK
STB SECTOR
*
LBSR XREAD
LBCS UXERR
LBSR XACK
LBSR XREAD
LBCS UXERR
*
LDX #BUFFER
LDA 38,X
INCA
STA MAXTRK
LDB 39,X
INCB
STB MAXSEC
LDA TRACK
LDB SECTOR
LBSR WRITSC
*
LBSR XACK
*
* Sector 4 to Last Track & Sector
*
*
LDA TRACK
LDB SECTOR
INCB
*
UXLOOP LDX #BUFFER
STA TRACK
STB SECTOR
*
LBSR XREAD
LBCS UXERR
LBSR XACK
LBSR XREAD
LBCS UXERR
*
LDX #BUFFER
LDA TRACK
LDB SECTOR
LBSR WRITSC
LBSR XACK
*
LDA TRACK
LDB SECTOR
INCB
CMPB MAXSEC
BNE UXLOOP
LDB #1
INCA
CMPA MAXTRK
BNE UXLOOP
*
*
* Write Boot sector
*
LDX #$C000
CLRA TRACK 0
LDB #$01 SECTOR 1
STA TRACK
STB SECTOR
LBSR WRITSC
*
UXEXIT LDX #UXMES1
JMP PDATA1
*
UXERR LDX #UXMES2
LBRA PDATA1
*
* Get a Byte using XModem protocol
* Carry clear => no errors
* Carry set => errors
*
XREAD PSHS U
LDU XSTATE
*
XBYTE0 LBSR INTER
BVC XBYTE1
LDA #NAK
LBSR OUTTER
LDU #XSTST
BRA XBYTE0
*
XBYTE1 JSR ,U
BNE XBYTE0
STU XSTATE
PULS U,PC
*
* START - LOOK FOR SOH (START OF HEADER) = $01
*
XSTST CMPA #SOH
BNE XSTST1
LDU #XSTBL
ANDCC #$FF-CFLAG-ZFLAG No abort, no valid data (no exit)
RTS
*
XSTST1 CMPA #EOT
BNE XSTST2
LDA #ACK
LBSR OUTTER
ORCC #CFLAG+ZFLAG Set (c)=1 abort & exit
RTS
*
XSTST2 CMPA #CAN
BNE XSTST3
ORCC #CFLAG+ZFLAG Set (c)=1 abort & exit
RTS
*
XSTST3 ANDCC #$FF-CFLAG-ZFLAG
RTS
*
* Got SOH
* Now get block number
*
XSTBL CMPA BLKNUM
BNE XSTBLE
LDU #XSTCOM
ANDCC #$FF-CFLAG-ZFLAG No abort, No valid data (no exit)
RTS
*
* Error in block number
*
XSTBLE LDA #NAK
LBSR OUTTER
LDU #XSTST
ANDCC #$FF-CFLAG-ZFLAG No abort, No valid data (no exit)
RTS
*
* Get complement of block number
*
XSTCOM COMA
CMPA BLKNUM
BNE XSTBLE
CLR CHKSUM
LDA #128
STA BYTCNT
LDU #XSTDA
ANDCC #$FF-CFLAG-ZFLAG No abort, No valid data (no exit)
RTS
*
* Get data bytes
*
XSTDA PSHS A
ADDA CHKSUM
STA CHKSUM
PULS A
DEC BYTCNT
BNE XSTDA1
LDU #XSTCK
XSTDA1 STA ,X+
ANDCC #$FF-CFLAG-ZFLAG No abort, no valid data (no exit)
RTS
*
* Byte count reached zero
* Check checksum byte
*
XSTCK CMPA CHKSUM
BNE XSTCK1 retry if wrong checksum
*
* Checksum OK ...
* increment block number
* Don't send ACK until data written to CF
*
INC BLKNUM
LDU #XSTST
ANDCC #$FF-CFLAG No abort
ORCC #ZFLAG Valid data (exit)
RTS
*
* Checksum Error detected ...
* Reset Sector counter in ACCB to last 128 byte boundary
* and send NAK
*
XSTCK1 PSHS B
TFR X,D
DECB
ANDB #128
TFR D,X
PULS B
LDA #NAK
XSTCK2 LBSR OUTTER
LDU #XSTST
ANDCC #$FF-CFLAG-ZFLAG No abort, no valid data (no exit)
RTS
*
* Acknowledge Data Received
*
XACK PSHS A
LDA #ACK
LBSR OUTTER
PULS A,PC
*
*
** FLEX 9 COMPACT FLASH DISK DRIVERS
*
* FOR SYS09BUG 1.2 ON THE BURCHED B5-X300
* WITH I/O MAPPED AT $XE000
* AND ROM MAPPED AT $XF000
* THE BURCHED B5-X300 HAS 256KBYTES OF SRAM
* THE FIRST 64K IS USED BY FLEX,
* THE SECOND 192K MAY BE USED AS A RAM DISK
*
*
IMASK EQU $10 IRQ MASK CC
FMASK EQU $40 FIRQ MASK CC
DATREG EQU $FFF0 DAT REGISTERS
*
CF_BASE EQU $E040
CF_DATA EQU CF_BASE+0
CF_ERROR EQU CF_BASE+1 ; read error
CF_FEATURE EQU CF_BASE+1 ; write feature
CF_SCNT EQU CF_BASE+2
CF_SNUM EQU CF_BASE+3
CF_CLO EQU CF_BASE+4
CF_CHI EQU CF_BASE+5
CF_HEAD EQU CF_BASE+6
CF_STATUS EQU CF_BASE+7 ; read status
CF_COMAND EQU CF_BASE+7 ; write command
*
* Command Equates
*
CMDREAD EQU $20 ; Read Single sector
CMDWRITE EQU $30 ; Write Single sector
CMDFEATURE EQU $EF
FEAT8BIT EQU $01 ; enable 8 bit transfers
HEADLBA EQU $E0
*
* Status bit equates
*
BSY EQU $80
DRDY EQU $40
DRQ EQU $08
ERR EQU $01
*
*
* INITIALIZE CF CARD FOR 8 BIT LBA MODE
*
INITDR BSR WAITRDY
LDA #HEADLBA
STA CF_HEAD
LDA #FEAT8BIT
STA CF_FEATURE
LDA #CMDFEATURE
STA CF_COMAND
BRA WAITRDY
*
* Seek track and sector
* A holds track number (0 - ??)
* B holds sector number (1 - ??)
* Sector numbers starts from 1
* subtract 1 to start from sector 0 on CF
*
SEEKTS DECB
STB CF_SNUM
STA CF_CLO
LDB DRVNUM
STB CF_CHI
LDB #$01
STB CF_SCNT
CLRB
RTS
*
* READ SECTORS FROM CF
*
*
READSC BSR SEEKTS
LDA #CMDREAD ; IDE READ MULTIPLE
STA CF_COMAND
BSR WAITRDY
*
* READ LOOP
*
CLRB
RDLP1 BSR WAITDRQ
LDA CF_DATA
STA ,X+
DECB
BNE RDLP1
*
CLRB
RDLP2 BSR WAITDRQ
LDA CF_DATA
DECB
BNE RDLP2
*
BSR WAITRDY
CLRB
RTS
*
* WRITE SECTOR TO CF
*
WRITSC BSR SEEKTS ; SEEK TRACK & SECTOR
LDA #CMDWRITE ; IDE WRITE MULTIPLE
STA CF_COMAND
BSR WAITRDY
*
* WRITE LOOP
*
CLRB
WRTLP1 BSR WAITDRQ
LDA ,X+
STA CF_DATA
DECB
BNE WRTLP1
*
CLRB
WRTLP2 BSR WAITDRQ
CLRA
STA CF_DATA
DECB
BNE WRTLP2
*
BSR WAITRDY
CLRB
RTS
*
* CHECK FOR BUSY
* Doubles as VERIFY
*
BUSY CLRB Never busy
RTS
*
* DRIVE SELECT DISK DRIVER
*
DRVSEL LDA 3,X GET DRIVE # FROM FCB
CMPA #3
BLS DRVS2 IF > 3, SET IT TO 0
CLRA
DRVS2 STA DRVNUM
CLRB ; SET Z, CLEAR C
RTS
*
* CHECK DRIVE READY DISK DRIVER
*
CHKDRV LDA 3,X
CLRB ; CLEAR C, SET Z
RTS
*
* WAIT UNTIL READY
*
WAITRDY LDA CF_STATUS
BITA #BSY
BNE WAITRDY
LDA CF_STATUS
BITA #DRDY
BEQ WAITRDY
RTS
*
* WAIT FOR DATA REQUEST
*
WAITDRQ LDA CF_STATUS
BITA #DRQ
BEQ WAITDRQ
RTS
*
*******************************************************
*
* Bootstrap FLEX Loader
*
* SBUG1.8 loads the bootstap loader at $C000
* however the Flex adaption manual has the
* bootstrap loader residing at $C100
*
******************************************************
*
* Equates
*
STACK EQU $C0FF
SCTBUF EQU $C300
*
* Start of Utility
*
ORG $C000
BOOT BRA LOAD0
FCB 0,0,0
TRK FCB 0 File start track
SCT FCB 0 File start sector
DNS FCB 0 Density Flag (not used)
TADR FDB $C000 Transfer address
LADR FDB 0 Load Address
DRNUM FCB 0 Drive number 0
*
LOAD0 LDS #STACK Set up stack
LDD TRK Set up start track and sector
STD SCTBUF
LDY #SCTBUF+256
*
* Perform actual file load
*
LOAD1 BSR GETCH Get acharcater
CMPA #$02 Data record hearder ?
BEQ LOAD2 Skip, is so
CMPA #$16 Xfr address hearder ?
BNE LOAD1 Loop if neither
*
* Get transfer address
*
BSR GETCH
STA TADR
BSR GETCH
STA TADR+1
BRA LOAD1
*
* Load data record
*
LOAD2 BSR GETCH Get load address
STA LADR
BSR GETCH
STA LADR+1
BSR GETCH Get Bytes count
TFR A,B
TSTB
BEQ LOAD1 Loop if count = 0
LDX LADR Get load address
LOAD3 PSHS B,X
BSR GETCH Get data character
PULS B,X
STA ,X+ Store at load address
DECB
BNE LOAD3 Loop until count = 0
BRA LOAD1
*
* Get Character routine
* Reads a sector if needed
*
GETCH CMPY #SCTBUF+256 out of data ?
BNE GETCH4 Go read Character if not
GETCH2 LDX #SCTBUF Point to buffer
LDD 0,X Get forward Link
BEQ GO if zero, file is loaded
BSR READ Read next sector
BNE BOOT start over if error
LDY #SCTBUF+4 Point past link
GETCH4 LDA ,Y+ Else, get a character
RTS
*
* File is loaded, Jump to it
*
GO JMP [TADR] Jump to transfer address
*
** FLEX 9 COMPACT FLASH DISK DRIVERS
*
* FOR SYS09BUG 1.2 ON THE BURCHED B5-X300
* WITH I/O MAPPED AT $XE000
* AND ROM MAPPED AT $XF000
* THE BURCHED B5-X300 HAS 256KBYTES OF SRAM
* THE FIRST 64K IS USED BY FLEX,
* THE SECOND 192K MAY BE USED AS A RAM DISK
*
*
*IMASK EQU $10 IRQ MASK CC
*FMASK EQU $40 FIRQ MASK CC
*DATREG EQU $FFF0 DAT REGISTERS
*
*CF_BASE EQU $E040
*CF_DATA EQU CF_BASE+0
*CF_ERROR EQU CF_BASE+1 ; read error
*CF_FEATURE EQU CF_BASE+1 ; write feature
*CF_SCNT EQU CF_BASE+2
*CF_SNUM EQU CF_BASE+3
*CF_CLO EQU CF_BASE+4
*CF_CHI EQU CF_BASE+5
*CF_HEAD EQU CF_BASE+6
*CF_STATUS EQU CF_BASE+7 ; read status
*CF_COMAND EQU CF_BASE+7 ; write command
*
* Command Equates
*
*CMDREAD EQU $20 ; Read Single sector
*CMDWRITE EQU $30 ; Write Single sector
*CMDFEATURE EQU $EF
*FEAT8BIT EQU $01 ; enable 8 bit transfers
*HEADLBA EQU $E0
*
* Status bit equates
*
*BSY EQU $80
*DRDY EQU $40
*DRQ EQU $08
*ERR EQU $01
*
* Seek track and sector
* A holds track number (0 - ??)
* B holds sector number (1 - ??)
* Sector numbers starts from 1
* subtract 1 to start from sector 0 on CF
*
SEEK DECB
STB CF_SNUM
STA CF_CLO
LDB DRNUM
STB CF_CHI
LDB #$01
STB CF_SCNT
CLRB
RTS
*
* READ SECTORS FROM CF
*
*
READ BSR SEEK
LDA #CMDREAD ; IDE READ MULTIPLE
STA CF_COMAND
BSR WTRDY
*
* READ LOOP
*
CLRB
READ1 BSR WTDRQ
LDA CF_DATA
STA ,X+
DECB
BNE READ1
*
CLRB
READ2 BSR WTDRQ
LDA CF_DATA
DECB
BNE READ2
*
BSR WTRDY
CLRB
RTS
*
* WAIT UNTIL READY
*
WTRDY LDA CF_STATUS
BITA #BSY
BNE WTRDY
LDA CF_STATUS
BITA #DRDY
BEQ WTRDY
RTS
*
* WAIT FOR DATA REQUEST
*
WTDRQ LDA CF_STATUS
BITA #DRQ
BEQ WTDRQ
RTS
*
END START
Go to most recent revision | Compare with Previous | Blame | View Log