Subversion Repositories ahb2wishbone

 
// Copyright (c) 2007 TooMuch Semiconductor Solutions Pvt Ltd.
 
 
//File name		:	ahb2wb.v
//Designer		: 	Manish Agarwal
//Date			: 	18 May, 2007
//Description	: 	AHB WISHBONE BRIDGE :- This design will connect AHB master interface with Wishbone slave.
//					This design will perform only single read-write operation.
//Revision		:	1.0
 
 
//******************************************************************************************************
 
`timescale 1 ns/1 ns
 
module ahb2wb(
	adr_o, dat_o, dat_i, ack_i, cyc_o,
	we_o, stb_o, hclk, hresetn, haddr, htrans, hwrite, hsize, hburst,
	hsel, hwdata, hrdata, hresp, hready, clk_i, rst_i
	);
 
 
//parameter declaration
	parameter AWIDTH = 16;
	parameter DWIDTH = 32;
 
 
//**************************************
// input ports
//**************************************
 
 //wishbone ports		
	input [DWIDTH-1:0]dat_i;						// data input from wishbone slave
	input ack_i;									// acknowledment from wishbone slave
	input clk_i;
	input rst_i;
 
 //AHB ports	
	input hclk; 									// clock
	input hresetn;									// active low reset
	input [DWIDTH-1:0]hwdata;						// data bus		
	input hwrite;									// write/read enable
	input [2:0]hburst;								// burst type
	input [2:0]hsize;								// data size
	input [1:0]htrans;								// type of transfer
	input hsel;										// slave select 
	input [AWIDTH-1:0]haddr;						// address bus	
 
 
//**************************************
// output ports
//**************************************
 
 //wishbone ports
	output [AWIDTH-1:0]adr_o;						// address to wishbone slave 
	output [DWIDTH-1:0]dat_o;						// data output for wishbone slave
	output cyc_o;									// signal to indicate valid bus cycle
	output we_o;									// write enable
	output stb_o;									// strobe to indicate valid data transfer cycle
 
 
 // AHB ports
	output [DWIDTH-1:0]hrdata;						// data output for wishbone slave
	output [1:0]hresp;								// response signal from slave
	output hready;									// slave ready
 
 
//**************************************
// inout ports
//**************************************
 
 
//**********************************************************************************
 
 
// datatype declaration
	reg [DWIDTH-1:0]hrdata;
	reg hready;
	reg [1:0]hresp;
	reg stb_o;
	wire we_o;
	reg cyc_o;
	wire [AWIDTH-1:0]adr_o;
	reg [DWIDTH-1:0]dat_o;
 
// local memory registers
	reg [AWIDTH-1 : 0]addr_temp;
	reg hwrite_temp;								// to hold write enable signal temporarily
 
//*******************************************************************
// AHB WISHBONE BRIDGE logic
//*******************************************************************
 
	assign #2 we_o = hwrite_temp;
	assign #2 adr_o = addr_temp;
 
	always @ (posedge hclk ) begin
		if (!hresetn) begin
			hresp  <= 2'b00;
			cyc_o <= 'b0;
			stb_o <= 'b0;
			addr_temp <= 'bx;
			hwrite_temp <= 'bx;
			dat_o <='bx;
		end
		else if(hready & hsel) begin
			case (hburst)
 				// single transfer
				3'b000 	:	begin										
								case (htrans)
									// idle transfer type
									2'b00 :	begin
												cyc_o <= 'b0;
												hresp <= 2'b00;			// ok response
												stb_o <= 'b0;
 
											end
 
									// busy transfer type
									2'b01 :	begin						
												hresp <= 2'b00; 		// ok response
												stb_o <= 'b0;
												cyc_o <= 'b1;
											end
 
									// Non-Sequential
									2'b10 : begin
												cyc_o <= 'b1;
												stb_o <= 'b1;
												addr_temp <= haddr;
												hwrite_temp <= hwrite;			// control signal stored that was received in address phase
											end
								endcase
							end
 
				default	:	cyc_o <= 'b0;
			endcase
		end
		else if (!hsel & hready) begin
			cyc_o <= 'b0;					//invalid bus transfer
		end
 
	end
 
 
// combinational logic - asynchronous read/write
	always@(hwrite_temp or hwdata or dat_i or ack_i or hresetn or stb_o ) begin
 
		if (!hresetn) begin
			hready <= 'b1;
		end
		else begin		
			if (stb_o) 
				hready = ack_i;
 
			if ( hwrite_temp ) 
				dat_o = hwdata;
			else if (!hwrite_temp) 
				hrdata = dat_i;
		end
 
	end	
 
endmodule