URL
https://opencores.org/ocsvn/amber/amber/trunk
Subversion Repositories amber
[/] [amber/] [trunk/] [hw/] [vlog/] [ethmac/] [eth_transmitcontrol.v] - Rev 13
Go to most recent revision | Compare with Previous | Blame | View Log
////////////////////////////////////////////////////////////////////// //// //// //// eth_transmitcontrol.v //// //// //// //// This file is part of the Ethernet IP core project //// //// http://www.opencores.org/projects/ethmac/ //// //// //// //// Author(s): //// //// - Igor Mohor (igorM@opencores.org) //// //// //// //// All additional information is avaliable in the Readme.txt //// //// file. //// //// //// ////////////////////////////////////////////////////////////////////// //// //// //// Copyright (C) 2001 Authors //// //// //// //// This source file may be used and distributed without //// //// restriction provided that this copyright statement is not //// //// removed from the file and that any derivative work contains //// //// the original copyright notice and the associated disclaimer. //// //// //// //// This source file is free software; you can redistribute it //// //// and/or modify it under the terms of the GNU Lesser General //// //// Public License as published by the Free Software Foundation; //// //// either version 2.1 of the License, or (at your option) any //// //// later version. //// //// //// //// This source is distributed in the hope that it will be //// //// useful, but WITHOUT ANY WARRANTY; without even the implied //// //// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR //// //// PURPOSE. See the GNU Lesser General Public License for more //// //// details. //// //// //// //// You should have received a copy of the GNU Lesser General //// //// Public License along with this source; if not, download it //// //// from http://www.opencores.org/lgpl.shtml //// //// //// ////////////////////////////////////////////////////////////////////// // // CVS Revision History // // $Log: not supported by cvs2svn $ // Revision 1.5 2002/11/19 17:37:32 mohor // When control frame (PAUSE) was sent, status was written in the // eth_wishbone module and both TXB and TXC interrupts were set. Fixed. // Only TXC interrupt is set. // // Revision 1.4 2002/01/23 10:28:16 mohor // Link in the header changed. // // Revision 1.3 2001/10/19 08:43:51 mohor // eth_timescale.v changed to timescale.v This is done because of the // simulation of the few cores in a one joined project. // // Revision 1.2 2001/09/11 14:17:00 mohor // Few little NCSIM warnings fixed. // // Revision 1.1 2001/08/06 14:44:29 mohor // A define FPGA added to select between Artisan RAM (for ASIC) and Block Ram (For Virtex). // Include files fixed to contain no path. // File names and module names changed ta have a eth_ prologue in the name. // File eth_timescale.v is used to define timescale // All pin names on the top module are changed to contain _I, _O or _OE at the end. // Bidirectional signal MDIO is changed to three signals (Mdc_O, Mdi_I, Mdo_O // and Mdo_OE. The bidirectional signal must be created on the top level. This // is done due to the ASIC tools. // // Revision 1.1 2001/07/30 21:23:42 mohor // Directory structure changed. Files checked and joind together. // // Revision 1.1 2001/07/03 12:51:54 mohor // Initial release of the MAC Control module. // // // // // // `include "timescale.v" module eth_transmitcontrol (MTxClk, TxReset, TxUsedDataIn, TxUsedDataOut, TxDoneIn, TxAbortIn, TxStartFrmIn, TPauseRq, TxUsedDataOutDetected, TxFlow, DlyCrcEn, TxPauseTV, MAC, TxCtrlStartFrm, TxCtrlEndFrm, SendingCtrlFrm, CtrlMux, ControlData, WillSendControlFrame, BlockTxDone ); parameter Tp = 1; input MTxClk; input TxReset; input TxUsedDataIn; input TxUsedDataOut; input TxDoneIn; input TxAbortIn; input TxStartFrmIn; input TPauseRq; input TxUsedDataOutDetected; input TxFlow; input DlyCrcEn; input [15:0] TxPauseTV; input [47:0] MAC; output TxCtrlStartFrm; output TxCtrlEndFrm; output SendingCtrlFrm; output CtrlMux; output [7:0] ControlData; output WillSendControlFrame; output BlockTxDone; reg SendingCtrlFrm; reg CtrlMux; reg WillSendControlFrame; reg [3:0] DlyCrcCnt; reg [5:0] ByteCnt; reg ControlEnd_q; reg [7:0] MuxedCtrlData; reg TxCtrlStartFrm; reg TxCtrlStartFrm_q; reg TxCtrlEndFrm; reg [7:0] ControlData; reg TxUsedDataIn_q; reg BlockTxDone; wire IncrementDlyCrcCnt; wire ResetByteCnt; wire IncrementByteCnt; wire ControlEnd; wire IncrementByteCntBy2; wire EnableCnt; // A command for Sending the control frame is active (latched) always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) WillSendControlFrame <= #Tp 1'b0; else if(TxCtrlEndFrm & CtrlMux) WillSendControlFrame <= #Tp 1'b0; else if(TPauseRq & TxFlow) WillSendControlFrame <= #Tp 1'b1; end // Generation of the transmit control packet start frame always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) TxCtrlStartFrm <= #Tp 1'b0; else if(TxUsedDataIn_q & CtrlMux) TxCtrlStartFrm <= #Tp 1'b0; else if(WillSendControlFrame & ~TxUsedDataOut & (TxDoneIn | TxAbortIn | TxStartFrmIn | (~TxUsedDataOutDetected))) TxCtrlStartFrm <= #Tp 1'b1; end // Generation of the transmit control packet end frame always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) TxCtrlEndFrm <= #Tp 1'b0; else if(ControlEnd | ControlEnd_q) TxCtrlEndFrm <= #Tp 1'b1; else TxCtrlEndFrm <= #Tp 1'b0; end // Generation of the multiplexer signal (controls muxes for switching between // normal and control packets) always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) CtrlMux <= #Tp 1'b0; else if(WillSendControlFrame & ~TxUsedDataOut) CtrlMux <= #Tp 1'b1; else if(TxDoneIn) CtrlMux <= #Tp 1'b0; end // Generation of the Sending Control Frame signal (enables padding and CRC) always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) SendingCtrlFrm <= #Tp 1'b0; else if(WillSendControlFrame & TxCtrlStartFrm) SendingCtrlFrm <= #Tp 1'b1; else if(TxDoneIn) SendingCtrlFrm <= #Tp 1'b0; end always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) TxUsedDataIn_q <= #Tp 1'b0; else TxUsedDataIn_q <= #Tp TxUsedDataIn; end // Generation of the signal that will block sending the Done signal to the eth_wishbone module // While sending the control frame always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) BlockTxDone <= #Tp 1'b0; else if(TxCtrlStartFrm) BlockTxDone <= #Tp 1'b1; else if(TxStartFrmIn) BlockTxDone <= #Tp 1'b0; end always @ (posedge MTxClk) begin ControlEnd_q <= #Tp ControlEnd; TxCtrlStartFrm_q <= #Tp TxCtrlStartFrm; end assign IncrementDlyCrcCnt = CtrlMux & TxUsedDataIn & ~DlyCrcCnt[2]; // Delayed CRC counter always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) DlyCrcCnt <= #Tp 4'h0; else if(ResetByteCnt) DlyCrcCnt <= #Tp 4'h0; else if(IncrementDlyCrcCnt) DlyCrcCnt <= #Tp DlyCrcCnt + 1'b1; end assign ResetByteCnt = TxReset | (~TxCtrlStartFrm & (TxDoneIn | TxAbortIn)); assign IncrementByteCnt = CtrlMux & (TxCtrlStartFrm & ~TxCtrlStartFrm_q & ~TxUsedDataIn | TxUsedDataIn & ~ControlEnd); assign IncrementByteCntBy2 = CtrlMux & TxCtrlStartFrm & (~TxCtrlStartFrm_q) & TxUsedDataIn; // When TxUsedDataIn and CtrlMux are set at the same time assign EnableCnt = (~DlyCrcEn | DlyCrcEn & (&DlyCrcCnt[1:0])); // Byte counter always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) ByteCnt <= #Tp 6'h0; else if(ResetByteCnt) ByteCnt <= #Tp 6'h0; else if(IncrementByteCntBy2 & EnableCnt) ByteCnt <= #Tp (ByteCnt[5:0] ) + 2'h2; else if(IncrementByteCnt & EnableCnt) ByteCnt <= #Tp (ByteCnt[5:0] ) + 1'b1; end assign ControlEnd = ByteCnt[5:0] == 6'h22; // Control data generation (goes to the TxEthMAC module) always @ (ByteCnt or DlyCrcEn or MAC or TxPauseTV or DlyCrcCnt) begin case(ByteCnt) 6'h0: if(~DlyCrcEn | DlyCrcEn & (&DlyCrcCnt[1:0])) MuxedCtrlData[7:0] = 8'h01; // Reserved Multicast Address else MuxedCtrlData[7:0] = 8'h0; 6'h2: MuxedCtrlData[7:0] = 8'h80; 6'h4: MuxedCtrlData[7:0] = 8'hC2; 6'h6: MuxedCtrlData[7:0] = 8'h00; 6'h8: MuxedCtrlData[7:0] = 8'h00; 6'hA: MuxedCtrlData[7:0] = 8'h01; 6'hC: MuxedCtrlData[7:0] = MAC[47:40]; 6'hE: MuxedCtrlData[7:0] = MAC[39:32]; 6'h10: MuxedCtrlData[7:0] = MAC[31:24]; 6'h12: MuxedCtrlData[7:0] = MAC[23:16]; 6'h14: MuxedCtrlData[7:0] = MAC[15:8]; 6'h16: MuxedCtrlData[7:0] = MAC[7:0]; 6'h18: MuxedCtrlData[7:0] = 8'h88; // Type/Length 6'h1A: MuxedCtrlData[7:0] = 8'h08; 6'h1C: MuxedCtrlData[7:0] = 8'h00; // Opcode 6'h1E: MuxedCtrlData[7:0] = 8'h01; 6'h20: MuxedCtrlData[7:0] = TxPauseTV[15:8]; // Pause timer value 6'h22: MuxedCtrlData[7:0] = TxPauseTV[7:0]; default: MuxedCtrlData[7:0] = 8'h0; endcase end // Latched Control data always @ (posedge MTxClk or posedge TxReset) begin if(TxReset) ControlData[7:0] <= #Tp 8'h0; else if(~ByteCnt[0]) ControlData[7:0] <= #Tp MuxedCtrlData[7:0]; end endmodule
Go to most recent revision | Compare with Previous | Blame | View Log