URL
https://opencores.org/ocsvn/forwardcom/forwardcom/trunk
Subversion Repositories forwardcom
[/] [forwardcom/] [trunk/] [config_r64.vh] - Rev 129
Go to most recent revision | Compare with Previous | Blame | View Log
////////////////////////////////////////////////////////////////////////////////// // Engineer: Agner Fog // // Create Date: 2020-06-06 // Last modified: 2021-08-06 // Module Name: config_r64.vh // Project Name: ForwardCom soft core model A // Target Devices: Artix 7 // Tool Versions: Vivado v. 2020.1 // License: CERN-OHL-W v. 2 or later // Description: Configuration parameters // // Configuration for 64 bit registers, 32kB data RAM, 64 kB code RAM // ////////////////////////////////////////////////////////////////////////////////// `define NUM_VECTOR_UNITS 0 // number of 64-bit vector units or lanes // Decide if we have 64 bits support. We can use less resources and have higher speed with the 32 bit version. // If 32 bits: General purpose registers are 32 bits. Temporary operand buffers are 32 bits. // Result buses are 32 bits. Results will be 32 bits, even for 64 bit instructions. // The data write buses to data cache and code cache are still 64 bits, using any part of the bus for smaller operand sizes. // If 64 bits: General purpose registers are 64 bits. 64 bit operand size is supported. // Uncomment this to support 64-bit operand type: `define SUPPORT_64BIT `ifdef SUPPORT_64BIT `define RB 64 // size of general purpose registers, 64 bits `define RB1 63 // index of most significant bit `else `define RB 32 // size of general purpose registers, 32 bits `define RB1 31 // index of most significant bit `endif // number of bits used in mask registers must be TAG_WIDTH < MASKSZ <= RB `define MASKSZ 16 //`define MASKSZ 32 //`define MASKSZ `RB // Clock frequency // Xilinx-specific: // To change the clock frequency, click on the clock_generator source to open the // Vivado Clocking Wizard and set the requested output frequency. // Use the timing summary to check if the design can work with this frequency. // The frequency defined below must match the frequency set in the clocking wizard: //`define CLOCK_FREQUENCY 68000000 // max clock frequency for 32-bit version `define CLOCK_FREQUENCY 58000000 // max clock frequency for 64-bit version // Serial input/output BUAD rate. 8 data bits, no parity, 1 stop bit //`define BAUD_RATE 19200 `define BAUD_RATE 57600 //`define BAUD_RATE 115200 // serial input buffer size is 2**IN_BUFFER_SIZE_LOG2 bytes // serial output buffer size is 2**OUT_BUFFER_SIZE_LOG2 bytes `define IN_BUFFER_SIZE_LOG2 10 // 1 kbyte `define OUT_BUFFER_SIZE_LOG2 11 // 2 kbytes // initial code in 64-bit lines. remember to put the second 32-bit word to the left: `define LOADER_FILE "loader.mem" // filename of hex file of machine code for loader `define MAX_LOADER_SIZE 32'H200 // >= size of loader code, in 32-bit words. Must be even // Loader entry address is the end of code memory - MAX_LOADER_SIZE // Restart address is the same address + 1 // code ram address lines. Each line has one 32-bit word = 4 bytes // code ram size = 2**(CODE_ADDR_WIDTH+2) //`define CODE_ADDR_WIDTH 13 // 32 kB `define CODE_ADDR_WIDTH 14 // 64 kB //`define CODE_ADDR_WIDTH 15 // 128 kB // data ram address lines. Each line has 1 byte. // data ram size = (2**DATA_ADDR_WIDTH) `define DATA_ADDR_WIDTH 15 // 32 kB // total address lines for code and data combined, used when writing code. // Total address space = (2**COMMON_ADDR_WIDTH) bytes `define COMMON_ADDR_WIDTH ((`CODE_ADDR_WIDTH+2>`DATA_ADDR_WIDTH) ? `CODE_ADDR_WIDTH+3 : `DATA_ADDR_WIDTH+1) // The code address space must start immediately after the data address space if IP-addressed data are used without load-time relocation: `define CODE_ADDR_START `DATA_ADDR_WIDTH // code write address starts at 2**`CODE_ADDR_START = end of data address space // code ram bus width `define CODE_DATA_WIDTH 64 // The number of entries in the call stack size is 2**CALL_STACK_POINTER_BITS - 1 `define CALL_STACK_POINTER_BITS 10 // number of system registers that behave as g.p. registers (renamed in flight) `define NUM_SYS_REGISTERS 3 // number of bits in instruction ID tag. // The maximum number of instruction tags in flight is 2**TAG_WIDTH - 1 `define TAG_WIDTH 5 // number of error types distinguished `define N_ERROR_TYPES 6 // Input/output port numbers `define INPORT_RS232 8 // input port for RS232 serial input `define INPORT_RS232_STATUS 9 // input port to read status of RS232 serial input `define OUTPORT_RS232 10 // output port for RS232 serial output `define OUTPORT_RS232_STATUS 11 // output port for RS232 serial output status
Go to most recent revision | Compare with Previous | Blame | View Log