URL
https://opencores.org/ocsvn/forwardcom/forwardcom/trunk
Subversion Repositories forwardcom
[/] [forwardcom/] [trunk/] [register_read.sv] - Rev 156
Go to most recent revision | Compare with Previous | Blame | View Log
//////////////////////////////////////////////////////////////////////////////////
// Engineer: Agner Fog
//
// Create Date: 2020-06-01
// Last modified: 2021-02-16
// Module Name: Register read
// Project Name: ForwardCom soft core
// Target Devices: Artix 7
// Tool Versions: Vivado v. 2019.2
// License: CERN-OHL-W
// Description: This pipeline stage comes after the decoder.
// It contains the integer register file. Register read requests come from the
// decoder stage and nowhere else. Register write commands come from the result buses.
// Tags are written to the register entries for values in flight in the pipeline.
//
// Putting the register file into this pipeline stage rather than in a separate module
// saves a lot of synchronization problems when results from a separate register file
// may come at a wrong clock cycle due to pipeline stall.
// This does not make this module excessively big.
//
//////////////////////////////////////////////////////////////////////////////////
`include "defines.vh"
module register_read (
input clock, // system clock (100 MHz)
input clock_enable, // clock enable. Used when single-stepping
input reset, // system reset.
input valid_in, // data from fetch module ready
input stall_in, // a later stage in pipeline is stalled
input [`CODE_ADDR_WIDTH-1:0] instruction_pointer_in, // address of current instruction
input [95:0] instruction_in, // current instruction, up to 3 words long
input tag_write_in, // write tag
input [`TAG_WIDTH-1:0] tag_val_in, // instruction tag value
input vector_in, // this is a vector instruction
input [1:0] category_in, // 00: multiformat, 01: single format, 10: jump
input [1:0] format_in, // 00: format A, 01: format E, 10: format B, 11: format C (format D never goes through decoder)
input [2:0] rs_status_in, // use of RS
input [2:0] rt_status_in, // Use of RT
input [1:0] ru_status_in, // Use of RU
input [1:0] rd_status_in, // Use of RD as input
input [1:0] mask_status_in, // Use of mask register
input mask_options_in, // mask register may contain options
input mask_alternative_in, // mask register and fallback register used for alternative purposes
input [2:0] fallback_use_in, // 0: no fallback, 1: same as first source operand, 2-4: RU, RS, RT
input [1:0] num_operands_in, // number of source operands
input [1:0] result_type_in, // type of result: 0: register, 1: system register, 2: memory, 3: other or nothing
input [1:0] offset_field_in, // address offset. 0: none, 1: 8 bit, possibly scaled, 2: 16 bit, 3: 32 bit
input [1:0] immediate_field_in, // immediate data field. 0: none, 1: 8 bit, 2: 16 bit, 3: 32 or 64 bit
input [1:0] scale_factor_in, // 00: index is not scaled, 01: index is scaled by operand size, 10: index is scaled by -1
input index_limit_in, // IM2 or IM3 contains a limit to the index
// ports for register write
input [`RB1:0] writeport1, // write port 1
input [5:0] writea1, // address input for writeport1 (extra bit is 1 for system registers)
input write_en1, // write enable for writeport1
input [`TAG_WIDTH-1:0] write_tag1, // tag must match to enable writing
input [`RB1:0] writeport2,
input [4:0] writea2,
input write_en2,
input [`TAG_WIDTH-1:0] write_tag2,
input [5:0] debug_reada, // read port for debugger
output reg valid_out, // An instruction is ready for output to next stage
output reg [`CODE_ADDR_WIDTH-1:0] instruction_pointer_out, // address of current instruction
output reg [95:0] instruction_out, // first word of instruction
output reg stall_predict_out, // predict next stage will stall
output reg [`TAG_WIDTH-1:0] tag_val_out,// instruction tag value
output reg vector_out, // this is a vector instruction
output reg [1:0] category_out, // 00: multiformat, 01: single format, 10: jump
output reg [1:0] format_out, // 00: format A, 01: format E, 10: format B, 11: format C (format D never goes through decoder)
output reg [1:0] num_operands_out, // number of source operands
output reg [1:0] result_type_out, // type of result: 0: register, 1: system register, 2: memory, 3: other or nothing
output reg [1:0] offset_field_out, // address offset. 0: none, 1: 8 bit, possibly scaled, 2: 16 bit, 3: 32 bit
output reg [1:0] immediate_field_out, // immediate data field. 0: none, 1: 8 bit, 2: 16 bit, 3: 32 or 64 bit
output reg [1:0] scale_factor_out, // 00: index is not scaled, 01: index is scaled by operand size, 10: index is scaled by -1
output reg index_limit_out, // IM2 or IM3 contains a limit to the index
output reg [`RB:0] rd_val_out, // value of register operand RD, bit `RB indicates missing
output reg [`RB:0] rs_val_out, // value of register operand RS, bit `RB indicates missing
output reg [`RB:0] rt_val_out, // value of register operand RT, bit `RB indicates missing
output reg [`RB:0] ru_val_out, // value of register operand RU, bit `RB indicates missing
output reg [`MASKSZ:0] regmask_val_out,// value of mask register, bit 32 indicates missing
output reg [1:0] rd_status_out, // uas of RD as input
output reg [2:0] rs_status_out, // use of RS
output reg [2:0] rt_status_out, // use of RT
output reg [1:0] ru_status_out, // use of RU
output reg [1:0] mask_status_out, // 1: mask register is used
output reg mask_alternative_out,// mask register and fallback register used for alternative purposes
output reg [2:0] fallback_use_out, // 0: no fallback, 1: same as first source operand, 2-4: RU, RS, RT
output reg [32:0] debugport_out // read for debugging purpose
);
// components of instruction
logic [1:0] il; // instruction length
logic [2:0] ot; // operand type
logic [4:0] mask; // mask register number
logic [4:0] rd; // rd register number
logic [5:0] rs; // rs register number
logic [5:0] rt; // rt register number
logic [4:0] ru; // ru register number
logic [5:0] tag_a; // tag address
// register values. Extra bit is 1 if not found
logic [`RB:0] rd_val; // value of register RD
logic [`RB:0] rs_val; // value of register RS
logic [`RB:0] rt_val; // value of register RT
logic [`RB:0] ru_val; // value of register RU
logic [`MASKSZ:0] mask_val; // value of mask register
logic mask_used; // a mask register is used
logic mask_off; // mask is known to be 0. input operands are not used. fallback may be used
logic stall_predict; // predict that address generator will stall in next clock cycle
logic [`COMMON_ADDR_WIDTH:0] instr_end; // address at end of instruction (word based)
logic [`TAG_WIDTH:0] rd_tag; // tag to look for if rd not available
logic [`TAG_WIDTH:0] rs_tag; // tag to look for if rs not available
logic [`TAG_WIDTH:0] rt_tag; // tag to look for if rt not available
logic [`TAG_WIDTH:0] ru_tag; // tag to look for if ru not available
logic [`TAG_WIDTH:0] mask_tag; // tag to look for if mask not available
// temporary debug info
logic [31:0] debug_bits;
logic [31:0] debug_bits_tag;
// temporary storage of register values during stall. Extra bit is 1 if not found
reg [`RB:0] rd_val_temp; // temporary value of register RD
reg [`RB:0] rs_val_temp; // temporary value of register RS
reg [`RB:0] rt_val_temp; // temporary value of register RT
reg [`RB:0] ru_val_temp; // temporary value of register RU
reg [`MASKSZ:0] mask_val_temp; // temporary value of mask mask register
reg last_stall; // was stalled in last clock cycle. May obtain values from the temporary registers
always_comb begin
// extract instruction fields, etc
il = instruction_in[`IL];
ot = instruction_in[`OT];
mask = instruction_in[`MASK];
rd = instruction_in[`RD];
rs = {(rs_status_in == `REG_SYSTEM), instruction_in[`RS]};
rt = instruction_in[`RT];
ru = instruction_in[`RU];
if (mask_status_in != `REG_UNUSED && instruction_in[`MASK] == 7) mask = `NUMCONTR;
if (rs_status_in == `REG_POINTER && offset_field_in >= `OFFSET_2) begin
if (instruction_in[`RS] == 28) rs = `THREADP;
if (instruction_in[`RS] == 29) rs = `DATAP;
end
/*
if (rt_status_in == `REG_POINTER && offset_field_in >= `OFFSET_2) begin
if (instruction_in[`RT] == 28) rt = `THREADP;
if (instruction_in[`RT] == 29) rt = `DATAP;
end */
tag_a = {result_type_in == `RESULT_SYS, rd}; // tag address
instr_end = instruction_pointer_in + (il[1] ? il : 2'b01) + {1'b1,{(`CODE_ADDR_START-2){1'b0}}}; // address at end of instruction
end
/************************************************************
general purpose and system register file
*************************************************************
Values of read addresses:
0-30: register r0 - r30
31: data stack pointer
32: numeric control register
33: thread pointer
34: data section pointer
35: currently unused
************************************************************/
parameter num_reg = 32 + `NUM_SYS_REGISTERS; // 32 general purpose registers and 3 system registers
reg [`RB:0] registers [num_reg];
// writing to registers through write ports
// generation loop for all general purpose and system registers
genvar i;
for (i=0; i < num_reg; i++) begin
always_ff @(posedge clock) if (clock_enable) begin
if (reset)
registers[i] <= 0; // reset general purpose registers, but not system registers
else if (tag_write_in && valid_in && i == tag_a)
registers[i] <= {1'b1, {(`RB-`TAG_WIDTH){1'b0}}, tag_val_in};
else if (write_en1 && i == writea1 && write_tag1 == registers[i][`TAG_WIDTH-1:0])
registers[i] <= {1'b0,writeport1};
else if (write_en2 && i == writea2 && write_tag2 == registers[i][`TAG_WIDTH-1:0])
registers[i] <= {1'b0,writeport2};
end
end
// get general purpose and system register values
always_comb begin
// tags to look for if registers are not available
if (last_stall) begin
// the tags to look for must be sampled in the first clock cycle of a stall
rd_tag = {rd_val_temp[`RB],rd_val_temp[`TAG_WIDTH-1:0]};
rs_tag = {rs_val_temp[`RB],rs_val_temp[`TAG_WIDTH-1:0]};
rt_tag = {rt_val_temp[`RB],rt_val_temp[`TAG_WIDTH-1:0]};
ru_tag = {ru_val_temp[`RB],ru_val_temp[`TAG_WIDTH-1:0]};
mask_tag = {mask_val_temp[`MASKSZ],mask_val_temp[`TAG_WIDTH-1:0]};
end else begin
// the tags to look for are found in the register file
rd_tag = {registers[rd][`RB],registers[rd][`TAG_WIDTH-1:0]};
rs_tag = {registers[rs][`RB],registers[rs][`TAG_WIDTH-1:0]};
rt_tag = {registers[rt][`RB],registers[rt][`TAG_WIDTH-1:0]};
ru_tag = {registers[ru][`RB],registers[ru][`TAG_WIDTH-1:0]};
mask_tag = {registers[mask][`RB],registers[mask][`TAG_WIDTH-1:0]};
end
if (rd_status_in == `REG_UNUSED) begin
rd_val = 0;
end else if (write_en1 && rd == writea1 && rd_tag[`TAG_WIDTH] && write_tag1 == rd_tag[`TAG_WIDTH-1:0]) begin
rd_val = {1'b0,writeport1}; // forwarding from write port 1
end else if (write_en2 && rd == writea2 && rd_tag[`TAG_WIDTH] && write_tag2 == rd_tag[`TAG_WIDTH-1:0]) begin
rd_val = {1'b0,writeport2}; // forwarding from write port 2
end else if (last_stall) begin
rd_val = rd_val_temp;
end else begin
rd_val = registers[rd]; // read value or tag from register file
end
if (rs_status_in == `REG_UNUSED) begin
rs_val = 0;
end else if (rs_status_in == `REG_POINTER && offset_field_in >= `OFFSET_2 && instruction_in[`RS] == 30) begin
rs_val = {instr_end,2'b0}; // instruction pointer as base pointer
end else if (write_en1 && rs == writea1 && rs_tag[`TAG_WIDTH] && write_tag1 == rs_tag[`TAG_WIDTH-1:0]) begin
rs_val = {1'b0,writeport1}; // forwarding from write port 1
end else if (write_en2 && rs == writea2 && rs_tag[`TAG_WIDTH] && write_tag2 == rs_tag[`TAG_WIDTH-1:0]) begin
rs_val = {1'b0,writeport2}; // forwarding from write port 2
end else if (last_stall) begin
rs_val = rs_val_temp;
end else begin
rs_val = registers[rs]; // read value or tag from register file
end
if (rt_status_in == `REG_UNUSED) begin
rt_val = 0;
//end else if (rt_status_in == `REG_POINTER && offset_field_in >= `OFFSET_2 && instruction_in[`RT] == 30) begin
// rt_val = {instr_end,2'b0} ; // instruction pointer as base pointer
end else if (write_en1 && rt == writea1 && rt_tag[`TAG_WIDTH] && write_tag1 == rt_tag[`TAG_WIDTH-1:0]) begin
rt_val = {1'b0,writeport1}; // forwarding from write port 1
end else if (write_en2 && rt == writea2 && rt_tag[`TAG_WIDTH] && write_tag2 == rt_tag[`TAG_WIDTH-1:0]) begin
rt_val = {1'b0,writeport2}; // forwarding from write port 2
end else if (last_stall) begin
rt_val = rt_val_temp;
end else begin
rt_val = registers[rt]; // read value or tag from register file
end
if (ru_status_in == `REG_UNUSED) begin
ru_val = 0;
end else if (write_en1 && ru == writea1 && ru_tag[`TAG_WIDTH] && write_tag1 == ru_tag[`TAG_WIDTH-1:0]) begin
ru_val = {1'b0,writeport1}; // forwarding from write port 1
end else if (write_en2 && ru == writea2 && ru_tag[`TAG_WIDTH] && write_tag2 == ru_tag[`TAG_WIDTH-1:0]) begin
ru_val = {1'b0,writeport2}; // forwarding from write port 2
end else if (last_stall) begin
ru_val = ru_val_temp;
end else begin
ru_val = registers[ru]; // read value or tag from register file
end
if (mask_status_in == `REG_UNUSED) begin
mask_val = 1;
end else if (write_en1 && mask == writea1 && mask_tag[`TAG_WIDTH] && write_tag1 == mask_tag[`TAG_WIDTH-1:0]) begin
mask_val = {1'b0,writeport1[`MASKSZ-1:0]}; // forwarding from write port 1
end else if (write_en2 && mask == writea2 && mask_tag[`TAG_WIDTH] && write_tag2 == mask_tag[`TAG_WIDTH-1:0]) begin
mask_val = {1'b0,writeport2[`MASKSZ-1:0]}; // forwarding from write port 2
end else if (last_stall) begin
mask_val = mask_val_temp;
end else begin
mask_val = {registers[mask][`RB],registers[mask][`MASKSZ-1:0]}; // read value or tag from register file
end
end
// save values during stall
always_ff @(posedge clock) if (clock_enable && valid_in) begin
last_stall <= stall_in;
if (stall_in) begin
rd_val_temp <= rd_val;
rs_val_temp <= rs_val;
rt_val_temp <= rt_val;
ru_val_temp <= ru_val;
mask_val_temp <= mask_val;
end else begin
rd_val_temp <= {1'b1,`RB'b0};
rs_val_temp <= {1'b1,`RB'b0};
rt_val_temp <= {1'b1,`RB'b0};
ru_val_temp <= {1'b1,`RB'b0};
mask_val_temp <= {1'b1,`MASKSZ'b0};
end
end
always_comb begin
// (The mask must be ignored for the NOP instruction. If there are any other instructions with
// zero operands that can have a valid mask then the above line must be modified.)
mask_used = (format_in == `FORMAT_A || format_in == `FORMAT_E) && mask != 7 && num_operands_in != 0;
// Check if result is masked off so that we don't have to wait for operands
mask_off = mask_used && mask_val[`MASKSZ] == 0 && mask_val[0] == 0 && !mask_alternative_in && !vector_in;
stall_predict = 0;
// rs used as pointer or index or vector length and not available in next clock cycle:
if (rs_status_in >= `REG_POINTER && rs_val[`RB] && !mask_off) stall_predict = 1;
// rt used as pointer and not available in next clock cycle:
if (rt_status_in >= `REG_POINTER && rt_val[`RB] && !mask_off) stall_predict = 1;
// rd is written to memory and not available in next clock cycle:
if (rd_status_in != 0 && result_type_in == `RESULT_MEM && rd_val[`RB] && !mask_off) stall_predict = 1;
// mask value is needed for memory write
if (mask_used && result_type_in == `RESULT_MEM && mask_val[`MASKSZ]) stall_predict = 1;
// signals for debugging
debug_bits = 0;
debug_bits[0] = rs_status_in >= `REG_POINTER;
debug_bits[8] = rt_status_in >= `REG_POINTER;
debug_bits[16] = rd_status_in;
debug_bits[24] = stall_predict;
debug_bits[25] = last_stall;
debug_bits[26] = stall_in;
debug_bits[27] = valid_in;
debug_bits_tag = 0;
//debug_bits_tag[`TAG_WIDTH-1:0] = tag_mirror[reg1_in];
end
// get values of missing operands from result buses.
// if stalling: keep looking for results and keep the values until not stalled
always_ff @(posedge clock) if (clock_enable) begin
// Predict stall in next stage if RS, RT, or RD is needed in the address generator stage
// and not yet available and not predicted to become available in the next clock cycle.
// Note, that while the stall prediction is looking forward one stage in the pipeline,
// it should not apply if the instruction is not moving to the next stage yet, hence
// stall_predict_out is not applied if stall_in.
stall_predict_out <= stall_predict && !stall_in && !reset && valid_in;
if (reset) valid_out <= 0;
else if (!stall_in) valid_out <= valid_in;
end
// generate outputs
always_ff @(posedge clock) if (clock_enable && !stall_in) begin
// first two words of instruction
instruction_out <= instruction_in;
// register values out
rd_val_out <= rd_val; // value of register operand RD, bit `RB indicates missing
rs_val_out <= rs_val; // value of register operand RS, bit `RB indicates missing
rt_val_out <= rt_val; // value of register operand RT, bit `RB indicates missing
ru_val_out <= ru_val; // value of register operand RU, bit `RB indicates missing
regmask_val_out <= mask_val; // value of mask register, bit 32 indicates missing
// other outputs are unchanged from input
instruction_pointer_out <= instruction_pointer_in;
tag_val_out <= tag_val_in; // tag for current instruction
vector_out <= vector_in; // vector instruction
category_out <= category_in; // instruction category
format_out <= format_in; // instruction format
rs_status_out <= rs_status_in; // use of rs register
rt_status_out <= rt_status_in; // use of rt register
ru_status_out <= ru_status_in; // use of ru register
rd_status_out <= rd_status_in; // use of rd register
mask_status_out <= mask_used | mask_options_in; // use of mask register
mask_alternative_out <= mask_alternative_in; // mask register and fallback register used for alternative purposes
fallback_use_out <= fallback_use_in; // 0: no fallback, 1: same as first source operand, 2-4: RU, RS, RT
num_operands_out <= num_operands_in; // number of input operands
result_type_out <= result_type_in; // type of result: 0: register, 1: system register, 2: memory, 3: other or nothing
offset_field_out <= offset_field_in; // address offset. 0: none, 1: 8 bit, possibly scaled, 2: 16 bit, 3: 32 bit
immediate_field_out <= immediate_field_in; // immediate data field. 0: none, 1: 8 bit, 2: 16 bit, 3: 32 or 64 bit
scale_factor_out <= scale_factor_in; // 00: index is not scaled, 01: index is scaled by operand size, 10: index is scaled by -1
index_limit_out <= index_limit_in; // The field indicated by offset_field contains a limit to the index
end
always_ff @(posedge clock) begin
debugport_out <= registers[debug_reada];// read register by debugger
end
endmodule
Go to most recent revision | Compare with Previous | Blame | View Log