URL
https://opencores.org/ocsvn/ima_adpcm_enc_dec/ima_adpcm_enc_dec/trunk
Subversion Repositories ima_adpcm_enc_dec
[/] [ima_adpcm_enc_dec/] [trunk/] [verilog/] [bench/] [tb_ima_adpcm.v] - Rev 4
Go to most recent revision | Compare with Previous | Blame | View Log
//--------------------------------------------------------------------------------------- // Project: ADPCM Encoder / Decoder // // Filename: tb_ima_adpcm.v (April 26, 2010 ) // // Author(s): Moti Litochevski // // Description: // This file implements the ADPCM encoder & decoder test bench. The input samples // to be encoded are read from a binary input file. The encoder stream output and // decoded samples are also compared with binary files generated by the Scilab // simulation. // //--------------------------------------------------------------------------------------- // // To Do: // - // //--------------------------------------------------------------------------------------- // // Copyright (C) 2010 Moti Litochevski // // This source file may be used and distributed without restriction provided that this // copyright statement is not removed from the file and that any derivative work // contains the original copyright notice and the associated disclaimer. // // THIS SOURCE FILE IS PROVIDED "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, // INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND // FITNESS FOR A PARTICULAR PURPOSE. // //--------------------------------------------------------------------------------------- `timescale 1ns / 1ns module test; //--------------------------------------------------------------------------------------- // internal signal reg clock; // global clock reg reset; // global reset reg [15:0] inSamp; // encoder input sample reg inValid; // encoder input valid flag wire inReady; // encoder input ready indication wire [3:0] encPcm; // encoder encoded output value wire encValid; // encoder output valid flag wire [15:0] decSamp; // decoder output sample value wire decValid; // decoder output valid flag integer sampCount, encCount, decCount; integer infid, encfid, decfid; integer intmp, enctmp, dectmp; reg [3:0] encExpVal; reg [15:0] decExpVal; reg [31:0] dispCount; // global definitions `define EOF -1 // file names `define IN_FILE "../../../scilab/test_in.bin" `define ENC_FILE "../../../scilab/test_enc.bin" `define DEC_FILE "../../../scilab/test_dec.bin" //--------------------------------------------------------------------------------------- // test bench implementation // global signals generation initial begin clock = 0; reset = 1; #40 reset = 0; end // clock generator - 50MHz clock always begin #10 clock = 0; #10 clock = 1; end // test bench dump variables initial begin $display(""); $display("IMA ADPCM encoder & decoder simulation"); $display("--------------------------------------"); $dumpfile("test.vcd"); $dumpvars(0, test); end //------------------------------------------------------------------ // encoder input samples read process initial begin // clear encoder input signal inSamp = 16'b0; inValid = 1'b0; // clear samples counter sampCount = 0; // binary input file infid = $fopen(`IN_FILE, "rb"); // wait for reset release while (reset) @(posedge clock); repeat (50) @(posedge clock); // read input samples file intmp = $fgetc(infid); while (intmp != `EOF) begin // read the next character to form the new input sample // Note that first byte is used as the low byte of the sample inSamp[7:0] <= intmp; inSamp[15:8] <= $fgetc(infid); // sign input sample is valid inValid <= 1'b1; @(posedge clock); // update the sample counter sampCount = sampCount + 1; // wait for encoder input ready assertion to confirm the new sample was read // by the encoder. while (!inReady) @(posedge clock); // read next character from the input file intmp = $fgetc(infid); end // sign input is not valid inValid <= 1'b0; @(posedge clock); // close input file $fclose(infid); end // encoder output checker - the encoder output is compared to the value read from // the ADPCM coded samples file. initial begin // clear encoded sample value encCount = 0; // open input file encfid = $fopen(`ENC_FILE, "rb"); // wait for reset release while (reset) @(posedge clock); // encoder output compare loop enctmp = $fgetc(encfid); while (enctmp != `EOF) begin // assign the expected value to a register with the same width encExpVal = enctmp; // wait for encoder output valid while (!encValid) @(posedge clock); // compare the encoded value with the value read from the input file if (encPcm != encExpVal) begin // announce error detection and exit simulation $display(" Error!"); $display("Error found in encoder output index %0d.", encCount+1); $display(" (expected value 'h%x, got value 'h%x)", encExpVal, encPcm); // wait for a few clock cycles before ending simulation repeat (20) @(posedge clock); $finish; end // update the encoded sample counter encCount = encCount + 1; // delay for a clock cycle after comparison @(posedge clock); // read next char from input file enctmp = $fgetc(encfid); end // close input file $fclose(encfid); end // decoder output checker - the decoder output is compared to the value read from // the ADPCM decoded samples file. initial begin // clear decoded sample value decCount = 0; dispCount = 0; // open input file decfid = $fopen(`DEC_FILE, "rb"); // wait for reset release while (reset) @(posedge clock); // display simulation progress bar title $write("Simulation progress: "); // decoder output compare loop dectmp = $fgetc(decfid); while (dectmp != `EOF) begin // read the next char to form the expected 16 bit sample value decExpVal[7:0] = dectmp; decExpVal[15:8] = $fgetc(decfid); // wait for decoder output valid while (!decValid) @(posedge clock); // compare the decoded value with the value read from the input file if (decSamp != decExpVal) begin // announce error detection and exit simulation $display(" Error!"); $display("Error found in decoder output index %0d.", decCount+1); $display(" (expected value 'h%x, got value 'h%x)", decExpVal, decSamp); // wait for a few clock cycles before ending simulation repeat (20) @(posedge clock); $finish; end // delay for a clock cycle after comparison @(posedge clock); // update the decoded sample counter decCount = decCount + 1; // check if simulation progress should be displayed if (dispCount[31:13] != (decCount >> 13)) $write("."); // update the display counter dispCount = decCount; // read next char from input file dectmp = $fgetc(decfid); end // close input file $fclose(decfid); // when decoder output is done announce simulation was successful $display(" Done"); $display("Simulation ended successfully after %0d samples", decCount); $finish; end //------------------------------------------------------------------ // device under test // Encoder instance ima_adpcm_enc enc ( .clock(clock), .reset(reset), .inSamp(inSamp), .inValid(inValid), .inReady(inReady), .outPCM(encPcm), .outValid(encValid), .outPredictSamp(/* not used */), .outStepIndex(/* not used */) ); // Decoder instance ima_adpcm_dec dec ( .clock(clock), .reset(reset), .inPCM(encPcm), .inValid(encValid), .inReady(decReady), .inPredictSamp(16'b0), .inStepIndex(7'b0), .inStateLoad(1'b0), .outSamp(decSamp), .outValid(decValid) ); endmodule //--------------------------------------------------------------------------------------- // Th.. Th.. Th.. Thats all folks !!! //---------------------------------------------------------------------------------------
Go to most recent revision | Compare with Previous | Blame | View Log