Subversion Repositories ion

--#############################################################################
-- ION MIPS-compatible CPU demo on Terasic DE-1 Cyclone-II starter board
--#############################################################################
-- This module is little more than a wrapper around the CPU and its memories.
--#############################################################################
 
library ieee;
use ieee.std_logic_1164.all;
use ieee.std_logic_arith.all;
use ieee.std_logic_unsigned.all;
 
-- FPGA i/o for Terasic DE-1 board
-- (Many of the board's i/o devices will go unused in this demo)
entity c2sb_demo is
    port ( 
        -- ***** Clocks
        clk_50MHz     : in std_logic;
 
        -- ***** Flash 4MB
        flash_addr    : out std_logic_vector(21 downto 0);
        flash_data    : in std_logic_vector(7 downto 0);
        flash_oe_n    : out std_logic;
        flash_we_n    : out std_logic;
        flash_reset_n : out std_logic;
 
        -- ***** SRAM 256K x 16
        sram_addr     : out std_logic_vector(17 downto 0);
        sram_data     : inout std_logic_vector(15 downto 0);
        sram_oe_n     : out std_logic;
        sram_ub_n     : out std_logic;
        sram_lb_n     : out std_logic;        
        sram_ce_n     : out std_logic;
        sram_we_n     : out std_logic;        
 
        -- ***** RS-232
        rxd           : in std_logic;
        txd           : out std_logic;
 
        -- ***** Switches and buttons
        switches      : in std_logic_vector(9 downto 0);
        buttons       : in std_logic_vector(3 downto 0);
 
        -- ***** Quad 7-seg displays
        hex0          : out std_logic_vector(0 to 6);
        hex1          : out std_logic_vector(0 to 6);
        hex2          : out std_logic_vector(0 to 6);
        hex3          : out std_logic_vector(0 to 6);
 
        -- ***** Leds
        red_leds      : out std_logic_vector(9 downto 0);
        green_leds    : out std_logic_vector(7 downto 0);
 
        -- ***** SD Card
        sd_data       : in  std_logic;
        sd_cs         : out std_logic;
        sd_cmd        : out std_logic;
        sd_clk        : out std_logic           
    );
end c2sb_demo;
 
architecture minimal of c2sb_demo is
 
 
--##############################################################################
-- 
 
--##############################################################################
-- RS232 interface signals
 
signal rx_rdy :             std_logic;
signal tx_rdy :             std_logic;
signal rs232_data_rx :      std_logic_vector(7 downto 0);
signal rs232_status :       std_logic_vector(7 downto 0);
signal data_io_out :        std_logic_vector(7 downto 0);
signal io_port :            std_logic_vector(7 downto 0);
signal read_rx :            std_logic;
signal write_tx :           std_logic;
 
 
--##############################################################################
-- 
 
 
-- CPU access to hex display (unused by Altair SW)
signal reg_display :        std_logic_vector(15 downto 0);
 
 
 
--##############################################################################
-- DE-1 board interface signals
 
-- Quad 7-segment display (non multiplexed) & LEDS
signal display_data :       std_logic_vector(15 downto 0);
signal reg_gleds :          std_logic_vector(7 downto 0);  
 
-- i/o signals
signal data_io_in :         std_logic_vector(7 downto 0);
signal data_mem_in :        std_logic_vector(7 downto 0);
signal data_rom_in :        std_logic_vector(7 downto 0);
signal rom_access :         std_logic;
signal rom_space :          std_logic;
signal breakpoint :         std_logic;
 
 
-- Clock & reset signals
signal clk_1hz :            std_logic;
signal clk_master :         std_logic;
signal counter_1hz :        std_logic_vector(25 downto 0);
signal reset :              std_logic;
signal clk :                std_logic;
 
-- SD control signals
signal sd_in :              std_logic;
signal reg_sd_dout :        std_logic;
signal reg_sd_clk :         std_logic;
signal reg_sd_cs :          std_logic;
 
signal cpu_rd_addr :        std_logic_vector(31 downto 0);
signal cpu_rd_data :        std_logic_vector(31 downto 0);
signal prev_rd_addr :       std_logic_vector(31 downto 28);
signal cpu_vma_data :       std_logic;
 
signal cpu_wr_addr :        std_logic_vector(31 downto 2);
signal cpu_wr_data :        std_logic_vector(31 downto 0);
signal cpu_byte_we :        std_logic_vector(3 downto 0);
 
signal data_uart :          std_logic_vector(31 downto 0);
 
signal data_uart_status :   std_logic_vector(31 downto 0);
signal uart_tx_rdy :        std_logic := '1';
signal uart_rx_rdy :        std_logic := '1';
 
 
begin
 
    mpu: entity work.mips_mpu
    port map (
        interrupt   => '0',
 
        rd_addr     => cpu_rd_addr,
        vma_data    => cpu_vma_data,
        data_r      => cpu_rd_data,
 
        wr_addr     => cpu_wr_addr,
        data_w      => cpu_wr_data,
        byte_we     => cpu_byte_we,
 
        mem_wait    => '0',
 
        uart_rxd    => rxd,
        uart_txd    => txd,
 
        clk         => clk,
        reset       => reset
    );
 
 
reg_display <= cpu_wr_addr(17 downto 2);
reg_gleds <= cpu_vma_data & "000" & cpu_byte_we;
 
-- red leds (light with '1') -- some CPU control signals 
red_leds(0) <= '0';
red_leds(1) <= '0';
red_leds(2) <= '0';
red_leds(3) <= '0';
red_leds(4) <= '0';
red_leds(5) <= '0';
red_leds(6) <= '0';
red_leds(7) <= '0';
red_leds(8) <= '0';
red_leds(9) <= clk_1hz;
 
 
--##############################################################################
-- terasIC Cyclone II STARTER KIT BOARD -- interface to on-board devices
--##############################################################################
 
--##############################################################################
-- FLASH (flash is unused in this demo)
--##############################################################################
 
flash_addr <= (others => '0');
 
flash_we_n <= '1'; -- all enable signals inactive
flash_oe_n <= '1';
flash_reset_n <= '1';
 
 
--##############################################################################
-- SRAM (used as 64K x 8)
--
-- NOTE: All writes go to SRAM independent of rom paging status
--##############################################################################
 
-- SRAM disabled for the time being
sram_addr <= (others => '0');
sram_data <= (others => 'Z');
sram_oe_n <= '1';
sram_ub_n <= '1';
sram_lb_n <= '1';
sram_ce_n <= '1';
sram_we_n <= '1';
 
 
--##############################################################################
-- RESET, CLOCK
--##############################################################################
 
-- Use button 3 as reset
reset <= not buttons(3);
 
 
-- Generate a 1-Hz 'clock' to flash a LED for visual reference.
process(clk_50MHz)
begin
  if clk_50MHz'event and clk_50MHz='1' then
    if reset = '1' then
      clk_1hz <= '0';
      counter_1hz <= (others => '0');
    else
      if conv_integer(counter_1hz) = 50000000 then
        counter_1hz <= (others => '0');
        clk_1hz <= not clk_1hz;
      else
        counter_1hz <= counter_1hz + 1;
      end if;
    end if;
  end if;
end process;
 
-- Master clock is external 50MHz oscillator
clk <= clk_50MHz;
 
 
--##############################################################################
-- LEDS, SWITCHES
--##############################################################################
 
-- Display the contents of a debug register at the green leds bar
green_leds <= reg_gleds; 
 
 
--##############################################################################
-- QUAD 7-SEGMENT DISPLAYS
--##############################################################################
 
-- So far, nothing to display
display_data <= reg_display;
 
 
-- 7-segment encoders; the dev board displays are not multiplexed or encoded
with display_data(15 downto 12) select hex3 <=  
"0000001" when X"0","1001111" when X"1","0010010" when X"2","0000110" when X"3",
"1001100" when X"4","0100100" when X"5","0100000" when X"6","0001111" when X"7",
"0000000" when X"8","0000100" when X"9","0001000" when X"a","1100000" when X"b",
"0110001" when X"c","1000010" when X"d","0110000" when X"e","0111000" when others;          
 
with display_data(11 downto 8) select hex2 <= 
"0000001" when X"0","1001111" when X"1","0010010" when X"2","0000110" when X"3",
"1001100" when X"4","0100100" when X"5","0100000" when X"6","0001111" when X"7",
"0000000" when X"8","0000100" when X"9","0001000" when X"a","1100000" when X"b",
"0110001" when X"c","1000010" when X"d","0110000" when X"e","0111000" when others;          
 
with display_data(7 downto 4) select hex1 <=  
"0000001" when X"0","1001111" when X"1","0010010" when X"2","0000110" when X"3",
"1001100" when X"4","0100100" when X"5","0100000" when X"6","0001111" when X"7",
"0000000" when X"8","0000100" when X"9","0001000" when X"a","1100000" when X"b",
"0110001" when X"c","1000010" when X"d","0110000" when X"e","0111000" when others;
 
with display_data(3 downto 0) select hex0 <=  
"0000001" when X"0","1001111" when X"1","0010010" when X"2","0000110" when X"3",
"1001100" when X"4","0100100" when X"5","0100000" when X"6","0001111" when X"7",
"0000000" when X"8","0000100" when X"9","0001000" when X"a","1100000" when X"b",
"0110001" when X"c","1000010" when X"d","0110000" when X"e","0111000" when others;
 
--##############################################################################
-- SD card interface
--##############################################################################
 
-- unused in this demo, but I did not bother to cut away the attached registers
sd_cs     <= '0';
sd_cmd    <= '0';
sd_clk    <= '0';
sd_in     <= 'Z';
 
 
--##############################################################################
-- SERIAL
--##############################################################################
 
--  Embedded in the MPU entity
 
end minimal;