URL
https://opencores.org/ocsvn/iso7816_3_master/iso7816_3_master/trunk
Subversion Repositories iso7816_3_master
[/] [iso7816_3_master/] [trunk/] [sources/] [RxCoreSelfContained.v] - Rev 11
Compare with Previous | Blame | View Log
/* Author: Sebastien Riou (acapola) Creation date: 23:57:02 08/31/2010 $LastChangedDate: 2011-01-29 13:16:17 +0100 (Sat, 29 Jan 2011) $ $LastChangedBy: acapola $ $LastChangedRevision: 11 $ $HeadURL: file:///svn/iso7816_3_master/iso7816_3_master/trunk/sources/RxCoreSelfContained.v $ This file is under the BSD licence: Copyright (c) 2011, Sebastien Riou All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. The names of contributors may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ `default_nettype none `timescale 1ns / 1ps module RxCoreSelfContained #(//parameters to override parameter DIVIDER_WIDTH = 1, parameter CLOCK_PER_BIT_WIDTH = 13, //allow to support default speed of ISO7816 parameter PRECISE_STOP_BIT = 0, //if 1, stopBit signal goes high exactly at start of stop bit instead of middle of parity bit //default conventions parameter START_BIT = 1'b0, parameter STOP_BIT1 = 1'b1, parameter STOP_BIT2 = 1'b1 ) ( output wire [7:0] dataOut, output wire overrunErrorFlag, //new data has been received before dataOut was read output wire dataOutReadyFlag, //new data available output wire frameErrorFlag, //bad parity or bad stop bits output wire endOfRx, //one cycle pulse: 1 during last cycle of last stop bit output wire run, //rx is definitely started, one of the three flag will be set output wire startBit, //rx is started, but we don't know yet if real rx or just a glitch output wire stopBit, //rx is over but still in stop bits input wire [DIVIDER_WIDTH-1:0] clkPerCycle, input wire [CLOCK_PER_BIT_WIDTH-1:0] clocksPerBit, input wire stopBit2,//0: 1 stop bit, 1: 2 stop bits input wire oddParity, //if 1, parity bit is such that data+parity have an odd number of 1 input wire msbFirst, //if 1, bits order is: startBit, b7, b6, b5...b0, parity input wire ackFlags, input wire serialIn, input wire comClk,//not used yet input wire clk, input wire nReset ); wire [CLOCK_PER_BIT_WIDTH-1:0] bitClocksCounter; wire bitClocksCounterEarlyMatch; wire bitClocksCounterMatch; wire [CLOCK_PER_BIT_WIDTH-1:0] bitClocksCounterCompare; wire bitClocksCounterInc; wire bitClocksCounterClear; wire bitClocksCounterInitVal; wire dividedClk; Counter #( .DIVIDER_WIDTH(DIVIDER_WIDTH), .WIDTH(CLOCK_PER_BIT_WIDTH), .WIDTH_INIT(1)) bitClocksCounterModule( .counter(bitClocksCounter), .earlyMatch(bitClocksCounterEarlyMatch), .match(bitClocksCounterMatch), .dividedClk(dividedClk), .divider(clkPerCycle), .compare(bitClocksCounterCompare), .inc(bitClocksCounterInc), .clear(bitClocksCounterClear), .initVal(bitClocksCounterInitVal), .clk(clk), .nReset(nReset)); RxCore #( .CLOCK_PER_BIT_WIDTH(CLOCK_PER_BIT_WIDTH), .PRECISE_STOP_BIT(PRECISE_STOP_BIT) ) rxCore ( .dataOut(dataOut), .overrunErrorFlag(overrunErrorFlag), .dataOutReadyFlag(dataOutReadyFlag), .frameErrorFlag(frameErrorFlag), .endOfRx(endOfRx), .run(run), .startBit(startBit), .stopBit(stopBit), .clocksPerBit(clocksPerBit), .stopBit2(stopBit2), .oddParity(oddParity), .msbFirst(msbFirst), .ackFlags(ackFlags), .serialIn(serialIn), .clk(clk), .nReset(nReset), .bitClocksCounterEarlyMatch(bitClocksCounterEarlyMatch), .bitClocksCounterMatch(bitClocksCounterMatch), .bitClocksCounterCompare(bitClocksCounterCompare), .bitClocksCounterInc(bitClocksCounterInc), .bitClocksCounterClear(bitClocksCounterClear), .bitClocksCounterInitVal(bitClocksCounterInitVal), .bitClocksCounter(bitClocksCounter) ); endmodule `default_nettype wire