URL
https://opencores.org/ocsvn/light52/light52/trunk
Subversion Repositories light52
[/] [light52/] [trunk/] [vhdl/] [light52_cpu.vhdl] - Rev 19
Go to most recent revision | Compare with Previous | Blame | View Log
-------------------------------------------------------------------------------- -- light52_cpu.vhdl -- light52 MCS51-compatible CPU core. -------------------------------------------------------------------------------- -- This is a 'naive' implementation of the MCS51 architecture that trades area -- for speed. -- -- At the bottom of the file there are some design notes referenced throughout -- the code ('@note1' etc.). -------------------------------------------------------------------------------- -- GENERICS: -- -- -- IMPLEMENT_BCD_INSTRUCTIONS -- Whether or not to implement BCD instructions. -- When true, instructions DA and XCHD will work as in the original MCS51. -- When false, those instructions will work as NOP, saving some logic. -- -- SEQUENTIAL_MULTIPLIER -- Sequential vs. combinational multiplier. -- When true, a sequential implementation will be used for the multiplier, -- which will usually save a lot of logic or a dedicated multiplier. -- When false, a combinational registered multiplier will be used. -- (NOT IMPLEMENTED -- setting it to true will raise an assertion failure). -- -- USE_BRAM_FOR_XRAM -- Use extra space in IRAM/uCode RAM as XRAM. -- When true, extra logic will be generated so that the extra space in the -- RAM block used for IRAM/uCode can be used as XRAM. -- This prevents RAM waste at some cost in area and clock rate. -- When false, any extra space in the IRAM physical block will be wasted. -- -------------------------------------------------------------------------------- -- INTERFACE SIGNALS: -- -- clk : Clock, active rising edge. -- reset : Synchronous reset, hold for at least 1 cycle. -- -- XCODE is assumed to be a synchronous ROM: -- -- code_addr : XCODE space address. -- code_rd : XCODE read data. Must be valid at all times with 1 -- cycle of latency (synchronous memory): -- code_rd[n] := XCODE(code_addr[n-1]) -- -- Interrupts are -- -- irq_source : Interrupt inputs. -- 0 is for vector 03h, 4 is for vector 23h. -- Not registsred; must be synchronous and remain high -- through a fetch_1 state in order to be acknowledged. -- Priorities are fixed: 0 highest, 4 lowest. -- -- XDATA is expected to be a synchronous 1-port RAM: -- -- xdata_addr : XDATA space address, valid when xdata_vma is '1'. -- xdata_vma : Asserted high when an XDATA rd/wr cycle is being done. -- xdata_rd : Read data. Must be valid the cycle after xdata_vma is -- asserted with xdata_we='0'. -- xdata_wr : Write data. Valid when xdata_vma is asserted with -- xdata_we='1'; -- xdata_we : '1' for XDATA write cycles, '0' for read cycles. -- -- SFRs external to the CPU are accessed as synchonous RAM: -- -- sfr_addr : SFR space address, valid when sfr_vma='1'. -- sfr_vma : Asserted high when an SFR rd/wr cycle is being done. -- sfr_rd : Read data. Must be valid the cycle after sfr_vma is -- asserted with sfr_we='0'. -- sfr_wr : Write data. Valid when sfr_vma is asserted with -- sfr_we='1'; -- sfr_we : '1' for SFR write cycles, '0' for read cycles. -- -- Note there's no code_vma. Even if there was one, see limitation #1 below. -------------------------------------------------------------------------------- -- MAJOR LIMITATIONS: -- -- 1.- Harvard architecture only. -- The core does not support non-Harvard, unified memory space (i.e. XCODE -- and XDATA on the same blocks). Signal sfr_vma is asserted the cycle -- before a fetch_1 state, when a code byte needs to be present at code_rd. -- In other words, XCODE and XDATA accesses are always simultaneous. -- Until the core supports wait states it only supports Harvard memory -- or a dual-port XCODE/XDATA memory. -- -- 2.- No support yet for sequential multiplier, only combinational. -- Setting SEQUENTIAL_MULTIPLIER to true will result in a synthesis -- or simulation failure. -- The core will use a dedicated multiplier block if the architecture & -- synthesis options allow for it (e.d. DSP48). -- -- 3.- Wasted space in RAM block used for IRAM. -- Setting USE_BRAM_FOR_XRAM to true will result in a synthesis -- or simulation failure. -- Architectures with BRAM blocks larger than 512 bytes (e.g. Xilinx -- Spartan) will have a lot of wasted space in the IRAM/uCode RAM block. -------------------------------------------------------------------------------- -- FIXMES: -- -- 1.- States fetch_1 and decode_0 might be overlapped with some other states -- for a noticeable gain in performance. -- 2.- Brief description of architecture is missing. -- 3.- Add optional 2nd DPTR register and implicit INC DPTR feature. -- 4.- Everything coming straight from a _reg should be named _reg too. -------------------------------------------------------------------------------- -- REFERENCES: -- [1] Tips for vendor-agnostic BRAM inference: -- http://www.danstrother.com/2010/09/11/inferring-rams-in-fpgas/ -------------------------------------------------------------------------------- -- Copyright (C) 2012 Jose A. Ruiz -- -- This source file may be used and distributed without -- restriction provided that this copyright statement is not -- removed from the file and that any derivative work contains -- the original copyright notice and the associated disclaimer. -- -- This source file is free software; you can redistribute it -- and/or modify it under the terms of the GNU Lesser General -- Public License as published by the Free Software Foundation; -- either version 2.1 of the License, or (at your option) any -- later version. -- -- This source is distributed in the hope that it will be -- useful, but WITHOUT ANY WARRANTY; without even the implied -- warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR -- PURPOSE. See the GNU Lesser General Public License for more -- details. -- -- You should have received a copy of the GNU Lesser General -- Public License along with this source; if not, download it -- from http://www.opencores.org/lgpl.shtml -------------------------------------------------------------------------------- library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; use work.light52_pkg.all; use work.light52_ucode_pkg.all; entity light52_cpu is generic ( -- Do not map unused BRAM onto XRAM space. USE_BRAM_FOR_XRAM : boolean := false; -- Implement DA and XCHD instructions by default. IMPLEMENT_BCD_INSTRUCTIONS : boolean := false; -- Use a combinational (dedicated) multiplier by default. SEQUENTIAL_MULTIPLIER : boolean := false ); port( clk : in std_logic; reset : in std_logic; code_addr : out std_logic_vector(15 downto 0); code_rd : in std_logic_vector(7 downto 0); irq_source : in std_logic_vector(4 downto 0); xdata_addr : out std_logic_vector(15 downto 0); xdata_rd : in std_logic_vector(7 downto 0); xdata_wr : out std_logic_vector(7 downto 0); xdata_vma : out std_logic; xdata_we : out std_logic; sfr_addr : out std_logic_vector(7 downto 0); sfr_rd : in std_logic_vector(7 downto 0); sfr_wr : out std_logic_vector(7 downto 0); sfr_vma : out std_logic; sfr_we : out std_logic ); end entity light52_cpu; architecture microcoded of light52_cpu is ---- Microcode table & instruction decoding ------------------------------------ signal ucode : unsigned(15 downto 0); -- uC word signal ucode_1st_half : unsigned(15 downto 0); -- uC if 1st-half opcode signal ucode_2nd_half : unsigned(15 downto 0); -- uC if 2nd-half opcode signal ucode_2nd_half_reg : unsigned(15 downto 0); -- signal ucode_is_2nd_half : std_logic; -- opcode is 2-nd half signal ucode_pattern : unsigned(2 downto 0); -- table row to replicate signal ucode_index : unsigned(6 downto 0); -- index into uC table signal do_fetch : std_logic; -- opcode is in code_rd -- uC class (t_class), only valid in state decode_0 signal uc_class_decode_0 : t_class; -- ALU instruction class (t_alu_class), only valid in state decode_0 signal uc_alu_class_decode_0 : t_alu_class; -- registered uc_alu_class_decode_0, used in state machine signal uc_alu_class_reg : t_alu_class; -- ALU control, valid only in state decode_0 signal uc_alu_fn_decode_0 : t_alu_fns; -- uc_alu_fn_decode_0 registered signal alu_fn_reg : t_alu_fns; -- Controls ALU/bitfield mux in the datapath. signal dpath_mux0_reg : std_logic; -- Flag mask for ALU instructions signal uc_alu_flag_mask : t_flag_mask; -- Flag mask for all instructions; valid in state decode_0 only signal flag_mask_decode_0 : t_flag_mask; -- Flag mask register for ALL instructions signal flag_mask_reg : t_flag_mask; -- Index of Rn register, valid for Rn addressing instructions only signal rn_index : unsigned(2 downto 0); ---- Datapath ------------------------------------------------------------------ -- Operand selection for ALU class instructions signal alu_class_op_sel_reg: t_alu_op_sel; signal alu_class_op_sel : t_alu_op_sel; -- ALU result valid for non-bit operations -- faster as it skips one mux signal nobit_alu_result : t_byte; -- ALU result signal alu_result : t_byte; signal alu_result_is_zero : std_logic; -- ALU result is zero signal acc_is_zero : std_logic; -- ACC is zero signal alu_cy : std_logic; -- ALU CY output signal alu_ov : std_logic; -- ALU OV output signal alu_ac : std_logic; -- ALU AC (aux cy) output signal bit_input : std_logic; -- Value of ALU bit operand signal load_b_sfr : std_logic; -- B register load enable signal mul_ready : std_logic; -- Multiplier is finished signal div_ready : std_logic; -- Divider is finished signal div_ov : std_logic; -- OV flag from divider ---- State machine ------------------------------------------------------------- -- Present state register and Next state signal ps, ns : t_cpu_state; ---- Interrupt handling -------------------------------------------------------- -- IRQ inputs ANDed to IE mask bits. signal irq_masked_inputs : std_logic_vector(4 downto 0); -- IRQ inputs ANDed to IE mask bits ANDed to IP mask bits. signal irq_masked_inputs_hp : std_logic_vector(4 downto 0); -- Level of highest-level active IRQ input. 0 is highest, 4 lowest, 7 is none. signal irq_level_inputs : unsigned(2 downto 0); -- Low 6 bits of IRQ service address. signal irq_vector : unsigned(5 downto 0); signal irq_active : std_logic; -- IRQ pending service signal load_ie : std_logic; -- IE register load enable signal load_ip : std_logic; -- IP register load enable -- Restore irq priority level (as per RETI execution). signal irq_restore_level : std_logic; -- High wwhen the active IRQ is allowed by the priority rules. signal irq_active_allowed : std_logic; -- High when serving a LOw Priority interrupt. signal irq_serving_lop : std_logic; -- High when serving a HIgh Priority interrupt. signal irq_serving_hip : std_logic; -- High when the active interrupt line is a HIgh Priority interrupt. signal irq_active_hip : std_logic; ---- CPU programmer's model registers ------------------------------------------ signal PC_reg : t_address; -- PC signal pc_incremented : t_address; -- PC + 1 | PC, controlled by... signal increment_pc : std_logic; -- ...PC increment enable signal A_reg : t_byte; -- ACC signal B_reg : t_byte; -- B signal PSW_reg : unsigned(7 downto 1); -- PSW excluding P flag signal PSW : t_byte; -- PSW, full (P is combinational) signal SP_reg : t_byte; -- SP signal SP_next : t_byte; -- Next value for SP signal IE_reg : t_byte; -- IE signal IP_reg : t_byte; -- IP signal alu_p : std_logic; -- P flag (from ALU) signal DPTR_reg : t_address; -- DPTR signal next_pc : t_address; -- Next value for PC signal jump_target : t_address; -- Addr to jump to signal jump_is_ljmp : std_logic; -- When doing jump, long jump signal instr_jump_is_ljmp : std_logic; -- For jump opcodes, long jump signal rel_jump_target : t_address; -- Address of a short jump signal rel_jump_delta : t_address; -- Offset of short jump -- 2K block index for AJMP/ACALL. Straight from the opcode. signal block_reg : unsigned(2 downto 0); signal code_byte : t_byte; -- Byte from XCODE (transient) signal ri_addr : t_byte; -- IRAM address of Ri register signal rn_addr : t_byte; -- IRAM address of Rn register -- The current ALU instruction CLASS uses Ri, not Rn signal alu_use_ri_by_class : std_logic; -- The current ALU instruction uses Ri and not Rn. signal alu_use_ri : std_logic; -- The current instruction is not an ALU instruction and uses Ri, not Rn signal non_alu_use_ri : std_logic; -- The current instruction uses Ri and not Rn signal use_ri : std_logic; -- Registered use_ri, controls the Ri/Rn mux. signal use_ri_reg : std_logic; signal rx_addr : t_byte; -- Output of Ri/Rx address selection mux signal bit_addr : t_byte; -- Byte address of bit operand -- Index of bit operand within its byte. signal bit_index : unsigned(2 downto 0); -- bit_index_registered in state decode_0 signal bit_index_reg : unsigned(2 downto 0); signal addr0_reg : t_byte; -- Aux address register 0... signal addr0_reg_input : t_byte; -- ...and its input mux signal addr1_reg : t_byte; -- Aux addr reg 1 -- Asserted when the PSW flags are implicitly updated by any instruction signal update_psw_flags : std_logic; signal load_psw : std_logic; -- PSW explicit (SFR) load enable signal load_acc_sfr : std_logic; -- ACC explicit (SFR) load enable signal load_addr0 : std_logic; -- Addr0 load enable signal load_sp : std_logic; -- SP explicit (SFR) load enable signal load_sp_implicit : std_logic; -- SP implicit load enable signal update_sp : std_logic; -- SP combined load enable ---- SFR interface ------------------------------------------------------------- signal sfr_addr_internal : unsigned(7 downto 0); -- SFR address signal sfr_vma_internal : std_logic; -- SFR access enable signal sfr_we_internal : std_logic; -- SFR write enable signal sfr_wr_internal : t_byte; -- SFR write data bus signal sfr_rd_internal : t_byte; -- SFR read data bus signal sfr_rd_internal_reg :t_byte; -- Registered SFR read data ---- Conditional jumps --------------------------------------------------------- signal jump_cond_sel_decode_0 : t_cc; -- Jump condition code... signal jump_cond_sel_reg : t_cc; -- ...registered to control mux signal jump_condition : std_logic; -- Value of jump condition signal cjne_condition : std_logic; -- Value of CJNE jump condition ---- BRAM used for IRAM and uCode table ---------------------------------------- -- The BRAM is a 512 byte table: 256 bytes for the decoding table and 256 bytes -- for the 8052 IRAM. -- FIXME handle Xilinx and arbitrary size FPGA BRAMs. constant BRAM_ADDR_LEN : integer := log2(BRAM_SIZE); subtype t_bram_addr is unsigned(BRAM_ADDR_LEN-1 downto 0); signal bram_addr_p0 : t_bram_addr; signal bram_addr_p1 : t_bram_addr; signal bram_data_p0 : t_byte; signal bram_data_p1 : t_byte; signal bram_we : std_logic; signal bram_wr_data_p0 : t_byte; -- Part of the BRAM inference template -- see [1] -- The BRAM is initializzed with the decoding table. shared variable bram : t_ucode_bram := ucode_to_bram(build_decoding_table(IMPLEMENT_BCD_INSTRUCTIONS)); -- IRAM/SFR address; lowest 8 bits of actual BRAM address. signal iram_sfr_addr : t_byte; -- IRAM/SFR read data signal iram_sfr_rd : t_byte; -- '1' when using direct addressing mode, '0' otherwise. signal direct_addressing : std_logic; -- '1' when using direct addressing to address range 80h..ffh, '0' otherwise. signal sfr_addressing : std_logic; signal sfr_addressing_reg : std_logic; -- Kind of addressing the current instruction is using signal direct_addressing_alu_reg : std_logic; signal alu_using_direct_addressing : std_logic; signal alu_using_indirect_addressing : std_logic; -- XRAM/MOVC interface and DPTR control logic ---------------------------------- signal load_dph : std_logic; -- DPTR(h) load enable signal load_dpl : std_logic; -- DPTR(l) load enable signal inc_dptr : std_logic; -- DPTR increment enable signal acc_ext16 : t_address; -- Accumulator zero-extended to 16 bits signal movc_base : t_address; -- Base for MOVC address signal movc_addr : t_address; -- MOVC address signal dptr_plus_a_reg : t_address; -- Registered DPTR+ACC adder begin --## 1.- State machine ######################################################### cpu_state_machine_reg: process(clk) begin if clk'event and clk='1' then if reset='1' then ps <= reset_0; else ps <= ns; end if; end if; end process cpu_state_machine_reg; cpu_state_machine_transitions: process(ps, uc_class_decode_0, uc_alu_class_decode_0, uc_alu_class_reg, jump_condition, alu_fn_reg, mul_ready,div_ready, irq_active) begin case ps is when reset_0 => ns <= fetch_1; when fetch_0 => ns <= fetch_1; when fetch_1 => -- Here's where we sample the pending interrupt flags... if irq_active='1' then -- ...and trigger interrupt response if necessary. ns <= irq_1; else ns <= decode_0; end if; when decode_0 => if uc_class_decode_0(5 downto 4) = "00" then case uc_alu_class_decode_0 is when AC_RI_to_A => ns <= alu_rx_to_ab; when AC_A_RI_to_A => ns <= alu_rx_to_ab; when AC_RI_to_RI => ns <= alu_rx_to_ab; when AC_RI_to_D => ns <= alu_rx_to_ab; when AC_D_to_A => ns <= alu_code_to_ab; when AC_D1_to_D => ns <= alu_code_to_ab; when AC_D_to_RI => ns <= alu_code_to_ab; when AC_D_to_D => ns <= alu_code_to_ab; when AC_A_RN_to_A => ns <= alu_rx_to_ab; when AC_RN_to_RN => ns <= alu_rx_to_ab; when AC_RN_to_A => ns <= alu_rx_to_ab; when AC_D_to_RN => ns <= alu_code_to_ab; when AC_RN_to_D => ns <= alu_rx_to_ab; when AC_I_to_D => ns <= alu_code_to_ab; when AC_I_D_to_D => ns <= alu_code_to_ab; when AC_I_to_RI => ns <= alu_code_to_t_rx_to_ab; when AC_I_to_RN => ns <= alu_code_to_t_rx_to_ab; when AC_I_to_A => ns <= alu_code_to_t; when AC_A_to_RI => ns <= alu_rx_to_ab; when AC_A_to_D => ns <= alu_code_to_ab; when AC_A_D_to_A => ns <= alu_code_to_ab; when AC_A_D_to_D => ns <= alu_code_to_ab; when AC_A_to_RN => ns <= alu_rx_to_ab; when AC_A_I_to_A => ns <= alu_code_to_t; when AC_A_to_A => ns <= alu_res_to_a; when AC_DIV => ns <= alu_div_0; when AC_MUL => ns <= alu_mul_0; when AC_DA => ns <= alu_daa_0; when others => ns <= bug_bad_opcode_class; end case; else case uc_class_decode_0 is when F_JRB => ns <= jrb_bit_0; when F_LJMP => ns <= fetch_addr_1; when F_AJMP => ns <= fetch_addr_0_ajmp; when F_LCALL => ns <= lcall_0; when F_ACALL => ns <= acall_0; when F_JR => ns <= load_rel; when F_CJNE_A_IMM => ns <= cjne_a_imm_0; when F_CJNE_A_DIR => ns <= cjne_a_dir_0; when F_CJNE_RI_IMM => ns <= cjne_ri_imm_0; when F_CJNE_RN_IMM => ns <= cjne_rn_imm_0; when F_DJNZ_DIR => ns <= djnz_dir_0; when F_DJNZ_RN => ns <= djnz_rn_0; when F_OPC => ns <= bit_res_to_c; when F_BIT => ns <= bit_op_0; when F_SPECIAL => ns <= special_0; when F_PUSH => ns <= push_0; when F_POP => ns <= pop_0; when F_MOV_DPTR => ns <= mov_dptr_0; when F_MOVX_DPTR_A => ns <= movx_dptr_a_0; when F_MOVX_A_DPTR => ns <= movx_a_dptr_0; when F_MOVX_A_RI => ns <= movx_a_ri_0; when F_MOVX_RI_A => ns <= movx_ri_a_0; when F_MOVC_PC => ns <= movc_pc_0; when F_MOVC_DPTR => ns <= movc_dptr_0; when F_XCH_DIR => ns <= xch_dir_0; when F_XCH_RI => ns <= xch_rx_0; when F_XCH_RN => ns <= xch_rn_0; when F_XCHD => ns <= alu_xchd_0; when F_JMP_ADPTR => ns <= jmp_adptr_0; when F_RET => ns <= ret_0; when F_NOP => ns <= fetch_1; when others => ns <= bug_bad_opcode_class; end case; end if; -- Interrupt processing ------------------------------------------ when irq_1 => ns <= irq_2; when irq_2 => ns <= irq_3; when irq_3 => ns <= irq_4; when irq_4 => ns <= fetch_0; -- Call/Ret instructions ----------------------------------------- when acall_0 => ns <= acall_1; when acall_1 => ns <= acall_2; when acall_2 => ns <= long_jump; when lcall_0 => ns <= lcall_1; when lcall_1 => ns <= lcall_2; when lcall_2 => ns <= lcall_3; when lcall_3 => ns <= lcall_4; when lcall_4 => ns <= fetch_0; when ret_0 => ns <= ret_1; when ret_1 => ns <= ret_2; when ret_2 => ns <= ret_3; when ret_3 => ns <= fetch_0; -- Special instructions ------------------------------------------ when special_0 => ns <= fetch_1; when push_0 => ns <= push_1; when push_1 => ns <= push_2; when push_2 => ns <= fetch_1; when pop_0 => ns <= pop_1; when pop_1 => ns <= pop_2; when pop_2 => ns <= fetch_1; when mov_dptr_0 => ns <= mov_dptr_1; when mov_dptr_1 => ns <= mov_dptr_2; when mov_dptr_2 => ns <= fetch_1; -- MOVC instructions --------------------------------------------- when movc_pc_0 => ns <= movc_1; when movc_dptr_0 => ns <= movc_1; when movc_1 => ns <= fetch_1; -- MOVX instructions --------------------------------------------- when movx_a_dptr_0 => ns <= fetch_1; when movx_dptr_a_0 => ns <= fetch_1; when movx_a_ri_0 => ns <= movx_a_ri_1; when movx_a_ri_1 => ns <= movx_a_ri_2; when movx_a_ri_2 => ns <= movx_a_ri_3; when movx_a_ri_3 => ns <= fetch_1; when movx_ri_a_0 => ns <= movx_ri_a_1; when movx_ri_a_1 => ns <= movx_ri_a_2; when movx_ri_a_2 => ns <= fetch_1; -- XCH instructions ---------------------------------------------- when xch_dir_0 => ns <= xch_1; when xch_rn_0 => ns <= xch_1; when xch_rx_0 => ns <= xch_rx_1; when xch_rx_1 => ns <= xch_1; when xch_1 => ns <= xch_2; when xch_2 => ns <= xch_3; when xch_3 => ns <= fetch_1; -- BIT instructions ---------------------------------------------- when bit_res_to_c => -- SETB C, CPL C and CLR C only ns <= fetch_1; when bit_op_0 => ns <= bit_op_1; when bit_op_1 => if uc_alu_class_reg(0)='0' then ns <= bit_op_2; else ns <= bit_res_to_c; end if; when bit_op_2 => ns <= fetch_1; -- BIT-testing relative jumps ------------------------------------ when jrb_bit_0 => ns <= jrb_bit_1; when jrb_bit_1 => if alu_fn_reg(1 downto 0)="11" then -- This is JBC; state jrb_bit_2 is where the bit is clear. ns <= jrb_bit_2; else ns <= jrb_bit_3; end if; when jrb_bit_2 => ns <= jrb_bit_3; when jrb_bit_3 => if jump_condition='1' then ns <= jrb_bit_4; else ns <= fetch_0; end if; when jrb_bit_4 => ns <= fetch_0; -- MUL/DIV instructions ------------------------------------------ when alu_div_0 => if div_ready='1' then ns <= fetch_1; else ns <= ps; end if; when alu_mul_0 => if mul_ready='1' then ns <= fetch_1; else ns <= ps; end if; -- BCD instructions ---------------------------------------------- when alu_daa_0 => ns <= alu_daa_1; when alu_daa_1 => ns <= fetch_1; when alu_xchd_0 => ns <= alu_xchd_1; when alu_xchd_1 => ns <= alu_xchd_2; when alu_xchd_2 => ns <= alu_xchd_3; when alu_xchd_3 => ns <= alu_xchd_4; when alu_xchd_4 => ns <= alu_xchd_5; when alu_xchd_5 => ns <= fetch_1; -- ALU instructions (other than MUL/DIV) ------------------------- when alu_rx_to_ab => case uc_alu_class_reg is when AC_RI_to_A | AC_A_RI_to_A | AC_RI_to_D | AC_RI_to_RI => ns <= alu_ram_to_ar; when AC_RN_to_D => ns <= alu_ram_to_t_code_to_ab; when AC_A_to_RI => ns <= alu_ram_to_ar_2; when others => ns <= alu_ram_to_t; end case; when alu_ram_to_ar_2 => ns <= alu_res_to_ram_ar_to_ab; when alu_ram_to_ar => ns <= alu_ar_to_ab; when alu_ar_to_ab => if uc_alu_class_reg = AC_RI_to_D then ns <= alu_ram_to_t_code_to_ab; else ns <= alu_ram_to_t; end if; when alu_ram_to_t => if uc_alu_class_reg = AC_D_to_A or uc_alu_class_reg = AC_A_D_to_A or uc_alu_class_reg = AC_RN_to_A or uc_alu_class_reg = AC_A_RN_to_A or uc_alu_class_reg = AC_RI_to_A or uc_alu_class_reg = AC_A_RI_to_A then ns <= alu_res_to_a; elsif uc_alu_class_reg = AC_D1_to_D then ns <= alu_res_to_ram_code_to_ab; else ns <= alu_res_to_ram; end if; when alu_res_to_ram_code_to_ab => ns <= fetch_1; when alu_res_to_a => ns <= fetch_1; when alu_ram_to_t_code_to_ab => ns <= alu_res_to_ram; when alu_res_to_ram => ns <= fetch_1; when alu_code_to_ab => case uc_alu_class_reg is when AC_I_to_D => ns <= alu_code_to_t; when AC_I_D_to_D => ns <= alu_ram_to_v_code_to_t; when AC_D_to_RI | AC_D_to_RN => ns <= alu_ram_to_t_rx_to_ab; when AC_A_to_D => ns <= alu_res_to_ram; when others => ns <= alu_ram_to_t; end case; when alu_ram_to_t_rx_to_ab => if uc_alu_class_reg = AC_D_to_RI then ns <= alu_ram_to_ar_2; else ns <= alu_res_to_ram; end if; when alu_res_to_ram_ar_to_ab => ns <= fetch_1; when alu_code_to_t => if uc_alu_class_reg = AC_I_to_D then ns <= alu_res_to_ram; else ns <= alu_res_to_a; end if; when alu_ram_to_v_code_to_t => ns <= alu_res_to_ram; when alu_code_to_t_rx_to_ab => if uc_alu_class_reg = AC_I_to_RI then ns <= alu_ram_to_ar_2; else ns <= alu_res_to_ram; end if; -- DJNZ Rn ------------------------------------------------------- when djnz_rn_0 => ns <= djnz_dir_1; -- DJNZ dir ------------------------------------------------------ when djnz_dir_0 => ns <= djnz_dir_1; when djnz_dir_1 => ns <= djnz_dir_2; when djnz_dir_2 => ns <= djnz_dir_3; when djnz_dir_3 => if jump_condition='1' then ns <= djnz_dir_4; else ns <= fetch_0; end if; when djnz_dir_4 => ns <= fetch_0; -- CJNE A, dir -------------------------------------------------- when cjne_a_dir_0 => ns <= cjne_a_dir_1; when cjne_a_dir_1 => ns <= cjne_a_dir_2; when cjne_a_dir_2 => if jump_condition='1' then ns <= cjne_a_dir_3; else ns <= fetch_0; end if; when cjne_a_dir_3 => ns <= fetch_0; -- CJNE Rn, #imm ------------------------------------------------ when cjne_rn_imm_0 => ns <= cjne_rn_imm_1; when cjne_rn_imm_1 => ns <= cjne_rn_imm_2; when cjne_rn_imm_2 => if jump_condition='1' then ns <= cjne_rn_imm_3; else ns <= fetch_0; end if; when cjne_rn_imm_3 => ns <= fetch_0; -- CJNE @Ri, #imm ------------------------------------------------ when cjne_ri_imm_0 => ns <= cjne_ri_imm_1; when cjne_ri_imm_1 => ns <= cjne_ri_imm_2; when cjne_ri_imm_2 => ns <= cjne_ri_imm_3; when cjne_ri_imm_3 => ns <= cjne_ri_imm_4; when cjne_ri_imm_4 => if jump_condition='1' then ns <= cjne_ri_imm_5; else ns <= fetch_0; end if; when cjne_ri_imm_5 => ns <= fetch_0; -- CJNE A, #imm ------------------------------------------------- when cjne_a_imm_0 => ns <= cjne_a_imm_1; when cjne_a_imm_1 => if jump_condition='1' then ns <= cjne_a_imm_2; else ns <= fetch_0; end if; when cjne_a_imm_2 => ns <= fetch_0; -- Relative and long jumps -------------------------------------- when load_rel => if jump_condition='1' then ns <= rel_jump; else ns <= fetch_1; end if; when rel_jump => ns <= fetch_0; when fetch_addr_1 => ns <= fetch_addr_0; when fetch_addr_0 => ns <= long_jump; when fetch_addr_0_ajmp => ns <= long_jump; when long_jump => ns <= fetch_0; when jmp_adptr_0 => ns <= fetch_0; -- Derailed state machine should end here ----------------------- -- NOTE: This applies to undecoded or unimplemented instructions, -- not to a state machine derailed by EM event, etc. when others => ns <= bug_bad_opcode_class; end case; end process cpu_state_machine_transitions; --## 2.- Interrupt handling #################################################### -- IP SFR is implemented as a regular SFR as per the MC51 architecture. load_ip <= '1' when sfr_addr_internal=SFR_ADDR_IP and sfr_we_internal='1' else '0'; IP_register: process(clk) begin if clk'event and clk='1' then if reset='1' then IP_reg <= (others => '0'); else if load_ip='1' then IP_reg <= alu_result; end if; end if; end if; end process IP_register; -- IE SFR is implemented as a regular SFR as per the MC51 architecture. load_ie <= '1' when sfr_addr_internal=SFR_ADDR_IE and sfr_we_internal='1' else '0'; IE_register: process(clk) begin if clk'event and clk='1' then if reset='1' then IE_reg <= (others => '0'); else if load_ie='1' then IE_reg <= alu_result; end if; end if; end if; end process IE_register; -- RETI restores the IRQ level to 7 (idle value). No interrupt will be serviced -- if its level is below this. Remember 0 is top, 4 is bottom and 7 is idle. irq_restore_level <= '1' when ps=ret_0 and alu_fn_reg(0)='1' else '0'; -- Mask the irq inputs with IE register bits... irq_masked_inputs <= irq_source and std_logic_vector(IE_reg(4 downto 0)); -- ...separate the highpriority interrupt inputs by masking with IP register... irq_masked_inputs_hp <= irq_masked_inputs and std_logic_vector(IP_reg(4 downto 0)); -- ...and encode the highest priority active input irq_level_inputs <= "000" when irq_masked_inputs_hp(0)='1' else "001" when irq_masked_inputs_hp(1)='1' else "010" when irq_masked_inputs_hp(2)='1' else "011" when irq_masked_inputs_hp(3)='1' else "100" when irq_masked_inputs_hp(4)='1' else "000" when irq_masked_inputs(0)='1' else "001" when irq_masked_inputs(1)='1' else "010" when irq_masked_inputs(2)='1' else "011" when irq_masked_inputs(3)='1' else "100" when irq_masked_inputs(4)='1' else "111"; irq_active_hip <= '1' when irq_masked_inputs_hp/="00000" else '0'; -- An active, enabled interrupt will be serviced only if... irq_active_allowed <= '1' when -- ...other high-priority interrupt is NOT being serviced... irq_serving_hip='0' and -- ...and either the incoming interrupt is high-priority... (irq_active_hip='1' or -- -- ...or no interrupt is being serviced at all; (irq_active_hip='0' and irq_serving_lop='0')) -- otherwise the interrupt is not allowed to proceed. else '0'; -- We have a pending irq if interrupts are enabled... irq_active <= '1' when IE_reg(7)='1' and -- ...and some interrupt source is active... irq_level_inputs/="111" and -- ...and the active interrupt is allowed by the priority -- rules... irq_active_allowed='1' -- ...otherwise the interrupt is ignored. else '0'; irq_registered_priority_encoder: process(clk) begin if clk'event and clk='1' then if reset='1' then -- After reset, no interrupt of either priority level is being -- serviced. irq_serving_hip <= '0'; irq_serving_lop <= '0'; elsif irq_restore_level='1' then -- RETI executed: if high-priority level was active... if irq_serving_hip='1' then -- ...disable it, reverting to the previous priority level... irq_serving_hip <= '0'; else -- otherwise disable the low priority level. irq_serving_lop <= '0'; end if; else -- Evaluate and register the interrupt priority in the same state -- the irq is to be acknowledged. if ps=fetch_1 and irq_active='1' then irq_serving_hip <= irq_active_hip; irq_serving_lop <= irq_serving_lop or (not irq_active_hip); -- This irq vector is going to be used in state irq_2. irq_vector <= irq_level_inputs & "011"; end if; end if; end if; end process irq_registered_priority_encoder; --## 3.- Combined register bank & decoding table ############################### -- No support yet for XRAM on this RAM block assert not USE_BRAM_FOR_XRAM report "This version of the core does not support using the IRAM/uCode "& "RAM block wasted space for XRAM" severity failure; -- This is the row of the opcode table that will be replicated for the 2nd half -- of the table. We always replicate row 7 (opcode X7h) except for 'DNJZ Rn' -- (opcodes d8h..dfh) where we replicate row 5 -- opcode d7h is not a DJNZ and -- breaks the pattern (see @note1). ucode_pattern <= "101" when code_rd(7 downto 4)="1101" else "111"; with code_rd(3) select ucode_index <= ucode_pattern & unsigned(code_rd(7 downto 4)) when '1', unsigned(code_rd(2 downto 0)) & unsigned(code_rd(7 downto 4)) when others; -- IRAM/SFR address source mux; controlled by current state with ps select iram_sfr_addr <= rx_addr when alu_rx_to_ab, rx_addr when alu_code_to_t_rx_to_ab, rx_addr when alu_ram_to_t_rx_to_ab, rx_addr when cjne_rn_imm_0, rx_addr when cjne_ri_imm_0, rx_addr when alu_xchd_0, rx_addr when movx_a_ri_0, rx_addr when movx_ri_a_0, rx_addr when xch_rx_0, rx_addr when xch_rn_0, addr0_reg when alu_res_to_ram_ar_to_ab, bit_addr when jrb_bit_0, bit_addr when bit_op_0, SP_reg when push_2, -- Write dir data to [sp] SP_reg when pop_0 | ret_0 | ret_1 | ret_2, SP_reg when acall_1 | acall_2 | lcall_2 | lcall_3, SP_reg when irq_2 | irq_3, addr0_reg when djnz_dir_1 | djnz_dir_2, addr0_reg when push_1, -- Read dir data for PUSH code_byte when cjne_a_imm_1, code_byte when cjne_a_dir_0, code_byte when cjne_a_dir_2, code_byte when cjne_rn_imm_1, code_byte when cjne_rn_imm_2, code_byte when cjne_ri_imm_4, code_byte when djnz_dir_0, -- DIR addr code_byte when djnz_dir_3, -- REL offset rx_addr when djnz_rn_0, addr0_reg when jrb_bit_2, code_byte when jrb_bit_3, addr0_reg when bit_op_2, code_byte when fetch_addr_0, code_byte when fetch_addr_0_ajmp, code_byte when alu_code_to_ab, -- DIRECT addressing code_byte when push_0, -- read dir address code_byte when pop_1, code_byte when acall_0 | lcall_0 | lcall_1, code_byte when alu_res_to_ram_code_to_ab, code_byte when alu_ram_to_t_code_to_ab, code_byte when load_rel, SFR_ADDR_DPH when mov_dptr_1, SFR_ADDR_DPL when mov_dptr_2, code_byte when xch_dir_0, addr0_reg when others; -- Assert this when an ALU instruction is about to use direct addressing. with ps select alu_using_direct_addressing <= '1' when alu_code_to_ab, '1' when xch_dir_0, '1' when alu_ram_to_t_code_to_ab, '0' when others; -- Assert this when an ALU instruction is using direct addressing. with ps select alu_using_indirect_addressing <= '1' when alu_ar_to_ab, '1' when alu_rx_to_ab, '1' when xch_rx_0, '1' when movx_a_ri_0, '1' when movx_ri_a_0, '1' when alu_ram_to_t_rx_to_ab, '1' when alu_res_to_ram_ar_to_ab, '1' when alu_code_to_t_rx_to_ab, '0' when others; -- This register remembers what kind of addressing the current ALU instruction -- is using. -- This is necessary because the ALU instruction states are shared by many -- different instructions with different addressing modes. alu_addressing_mode_flipflop: process(clk) begin if clk'event and clk='1' then if reset = '1' then direct_addressing_alu_reg <= '0'; else if alu_using_direct_addressing = '1' then direct_addressing_alu_reg <= '1'; elsif alu_using_indirect_addressing = '1' then direct_addressing_alu_reg <= '0'; end if; end if; end if; end process alu_addressing_mode_flipflop; -- This signal controls the T reg input mux. it should be valid in the cycle -- the read/write is performed AND in the cycle after a read. -- FIXME these should be asserted in READ or WRITE states; many are not! review! with ps select direct_addressing <= -- For most instructions all we need to know is the current state... '0' when alu_rx_to_ab, '0' when cjne_a_imm_0, '0' when cjne_a_imm_1, '0' when cjne_ri_imm_4, '0' when cjne_ri_imm_3, '0' when fetch_addr_0, '0' when load_rel, '0' when cjne_rn_imm_1, '0' when cjne_rn_imm_2, '1' when jrb_bit_0 | jrb_bit_1 | jrb_bit_2, '1' when bit_op_0 | bit_op_1 | bit_op_2, -- FIXME these below have been verified and corrected '1' when djnz_dir_0, '1' when djnz_dir_1, '1' when djnz_dir_2, '1' when push_0, '1' when pop_1 | pop_2, '0' when movx_a_ri_0, '0' when movx_ri_a_0, '1' when xch_dir_0, '1' when cjne_a_dir_0, '1' when cjne_a_dir_1, '0' when alu_xchd_2 | alu_xchd_3, -- ... and for ALU instructions we use info recorded while decoding. '1' when alu_code_to_ab, direct_addressing_alu_reg when xch_1, direct_addressing_alu_reg when xch_2, direct_addressing_alu_reg when alu_ar_to_ab, direct_addressing_alu_reg when alu_ram_to_t, direct_addressing_alu_reg when alu_ram_to_t_code_to_ab, direct_addressing_alu_reg when alu_ram_to_t_rx_to_ab, direct_addressing_alu_reg when alu_ram_to_v_code_to_t, direct_addressing_alu_reg when alu_res_to_ram, '1' when alu_res_to_ram_code_to_ab, -- D1 -> D only '0' when alu_res_to_ram_ar_to_ab, '0' when others; -- SFRs are only ever accessed by direct addresing to area 80h..ffh sfr_addressing <= direct_addressing and iram_sfr_addr(7); -- In 'fetch' states (including the last state of all instructions) the BRAM -- is used as a decode table indexed by the opcode -- both ports! -- The decode table is in the lowest 256 bytes and the actual IRAM data is -- in the highest 256 bytes, thus the address MSB. with do_fetch select bram_addr_p0 <= -- 'fetch' states '0' & ucode_index & '0' when '1', '1' & iram_sfr_addr when others; with do_fetch select bram_addr_p1 <= -- 'fetch' states '0' & ucode_index & '1' when '1', '1' & iram_sfr_addr when others; -- FIXME SFR/RAM selection bit: make sure it checks with ps select bram_we <= not sfr_addressing when alu_res_to_ram, not sfr_addressing when alu_res_to_ram_code_to_ab, '1' when alu_res_to_ram_ar_to_ab, not sfr_addressing when djnz_dir_2, not sfr_addressing when bit_op_2, not sfr_addressing when jrb_bit_2, not sfr_addressing when push_2, -- FIXME verify not sfr_addressing when pop_2, -- FIXME verify not sfr_addressing when xch_2, '1' when alu_xchd_4, '1' when acall_1 | acall_2 | lcall_2 | lcall_3, '1' when irq_2 | irq_3, '0' when others; -- The datapath result is what's written back to the IRAM/SFR, except when -- pushing the PC in a xCALL instruction. with ps select bram_wr_data_p0 <= PC_reg(7 downto 0) when acall_1 | lcall_2 | irq_2, PC_reg(15 downto 8) when acall_2 | lcall_3 | irq_3, alu_result when others; -- IMPORTANT: the 2-port BRAM is inferred using a template which is valid for -- both Altera and Xilinx. Otherwise, the synth tools would infer TWO BRAMs -- instead of one. -- This template is FRAGILE: for example, changing the order of assignments in -- process *_port0 will break the synthesis (i.e. 2 BRAMs again). -- See a more detailed explaination in [3]. -- BRAM port 0 is read/write (i.e. same address for read and write) register_bank_bram_port0: process(clk) begin if clk'event and clk='1' then if bram_we='1' then bram(to_integer(bram_addr_p0)) := bram_wr_data_p0; end if; bram_data_p0 <= bram(to_integer(bram_addr_p0)); end if; end process register_bank_bram_port0; -- Port 1 is read only register_bank_bram_port1: process(clk) begin if clk'event and clk='1' then bram_data_p1 <= bram(to_integer(bram_addr_p1)); end if; end process register_bank_bram_port1; -- End of BRAM inference template --## 4.- Instruction decode logic ############################################## -- Assert do_fetch on the states when the *opcode* is present in code_rd. -- (not asserted for other instruction bytes, only the opcode). with ps select do_fetch <= '1' when fetch_1, '0' when others; -- The main decode word is the synchrous BRAM output. Which means it is only -- valid for 1 clock cycle (state decode_0). Most state machine decisions are -- taken in that state. All information which is needed at a later state, like -- ALU control signals, is registered. -- Note that the BRAM is used for the 1st half of the decode table (@note1)... ucode_1st_half <= bram_data_p0 & bram_data_p1; -- ...the 2nd hald of the table is done combinationally and then registered. ucode_2nd_half(8 downto 0) <= ucode_1st_half(8 downto 0); -- We take advantage of the opcode table layout: the 2nd half columns are always -- identical to the 1st half column, 7th or 5th row opcode (see ucode_pattern), -- except for the addressing mode: with code_rd(7 downto 4) select ucode_2nd_half(15 downto 9) <= "00" & AC_RN_to_RN when "0000", "00" & AC_RN_to_RN when "0001", "00" & AC_A_RN_to_A when "0010", "00" & AC_A_RN_to_A when "0011", "00" & AC_A_RN_to_A when "0100", "00" & AC_A_RN_to_A when "0101", "00" & AC_A_RN_to_A when "0110", "00" & AC_I_to_RN when "0111", "00" & AC_RN_to_D when "1000", "00" & AC_A_RN_to_A when "1001", "00" & AC_D_to_RN when "1010", F_CJNE_RN_IMM & CC_CJNE(3 downto 3) when "1011", F_XCH_RN & "0" when "1100", F_DJNZ_RN & CC_NZ(3 downto 3) when "1101", "00" & AC_RN_to_A when "1110", "00" & AC_A_to_RN when others; -- Register the combinational half of the uCode table so its timing is the same -- as the BRAM (so that both halves have the same timing). process(clk) begin if clk'event and clk='1' then -- Register the information as soon as it is available: get opcode bits -- when the opcode is in code_rd... if do_fetch='1' then ucode_is_2nd_half <= code_rd(3); rn_index <= unsigned(code_rd(2 downto 0)); end if; -- ...and get the ucode word when it is valid: the lowest half of the -- ucode word comes from the ucode BRAM and is valid in decode_0. if ps = decode_0 then ucode_2nd_half_reg <= ucode_2nd_half; end if; end if; end process; -- uCode may come from the BRAM (1st half of the table) or from combinational -- logic (2nd half). This is the multiplexor. ucode <= ucode_1st_half when ucode_is_2nd_half='0' else ucode_2nd_half_reg; -- Extract uCode fields for convenience. -- For ALU instructions, we have the flag mask in the uCode word... uc_alu_flag_mask <= ucode_1st_half(8 downto 7); -- ...and all other instructions only update the C flag, if any. with uc_class_decode_0(5 downto 4) select flag_mask_decode_0 <= uc_alu_flag_mask when "00", FM_C when others; -- Will only be used in a few states. -- The mux for signal ucode operates after state decode_0, because its input -- ucode_2nd_half_reg ir registered in that state. These following signals -- depend on the ucode but need to be valid IN state decode_0 so they are muxed -- separately directly on the opcode bit. -- Valid only in state decode_0, all of these are registered too for later use. with ucode_is_2nd_half select jump_cond_sel_decode_0 <= ucode_1st_half(9 downto 6) when '0', ucode_2nd_half(9 downto 6) when others; with ucode_is_2nd_half select uc_alu_fn_decode_0 <= ucode_1st_half(5 downto 0) when '0', ucode_2nd_half(5 downto 0) when others; with ucode_is_2nd_half select uc_class_decode_0 <= ucode_1st_half(15 downto 10) when '0', ucode_2nd_half(15 downto 10) when others; with ucode_is_2nd_half select uc_alu_class_decode_0 <= -- ALU opc. addrng. mode ucode_1st_half(13 downto 9) when '0', ucode_2nd_half(13 downto 9) when others; -- Register ALU & conditional jump control signals for use in states -- after decode_0. alu_control_registers: process(clk) begin if clk'event and clk='1' then if ps=decode_0 then uc_alu_class_reg <= uc_alu_class_decode_0; alu_class_op_sel_reg <= alu_class_op_sel; use_ri_reg <= use_ri; flag_mask_reg <= flag_mask_decode_0; alu_fn_reg <= uc_alu_fn_decode_0; dpath_mux0_reg <= uc_alu_fn_decode_0(1) and uc_alu_fn_decode_0(0); jump_cond_sel_reg <= jump_cond_sel_decode_0; instr_jump_is_ljmp <= ucode(10); end if; end if; end process alu_control_registers; --## 5.- PC and code address generation ######################################## rel_jump_delta(15 downto 8) <= (others => addr0_reg(7)); rel_jump_delta(7 downto 0) <= addr0_reg; rel_jump_target <= PC_reg + rel_jump_delta; -- A jump is LONG when running LJMP/LCALL OR acknowledging an interrupt. jump_is_ljmp <= '1' when ps=irq_4 else instr_jump_is_ljmp; -- Mux for two kinds of jump target, AJMP/LJMP (jumps and calls) with jump_is_ljmp select jump_target <= PC_reg(15 downto 11) & block_reg & addr0_reg when '0', -- AJMP addr1_reg & addr0_reg when others; -- LJMP -- Decide whether or not to increment the PC by looking at the NEXT state, not -- the present one. See @note5. with ns select increment_pc <= '1' when decode_0, -- See @note6. '1' when alu_ram_to_t_code_to_ab, '1' when alu_code_to_ab, '1' when alu_res_to_ram_code_to_ab, '1' when alu_ram_to_v_code_to_t, '1' when alu_code_to_t_rx_to_ab, '1' when alu_code_to_t, '1' when jrb_bit_0, '1' when jrb_bit_3, '1' when bit_op_0, '1' when cjne_a_imm_0, '1' when cjne_a_imm_1, '1' when cjne_a_dir_0, '1' when cjne_a_dir_2, '1' when cjne_ri_imm_3, '1' when cjne_ri_imm_4, '1' when cjne_rn_imm_1, '1' when cjne_rn_imm_2, '1' when fetch_addr_0, '1' when fetch_addr_1, '1' when fetch_addr_0_ajmp, '1' when acall_0 | lcall_0 | lcall_1, '1' when load_rel, '1' when djnz_dir_0, '1' when djnz_dir_3, '1' when push_0, '1' when pop_1, '1' when mov_dptr_0, '1' when mov_dptr_1, '1' when xch_dir_0, '0' when others; with increment_pc select pc_incremented <= PC_reg + 1 when '1', PC_reg when others; with ps select next_pc <= X"0000" when reset_0, jump_target when long_jump | lcall_4 | ret_3 | irq_4, dptr_plus_a_reg when jmp_adptr_0, rel_jump_target when rel_jump, rel_jump_target when cjne_a_imm_2, rel_jump_target when cjne_a_dir_3, rel_jump_target when cjne_ri_imm_5, rel_jump_target when cjne_rn_imm_3, rel_jump_target when djnz_dir_4, rel_jump_target when jrb_bit_4, pc_incremented when others; program_counter: process(clk) begin if clk'event and clk='1' then if reset='1' then PC_reg <= (others => '0'); else PC_reg <= next_pc; end if; end if; end process program_counter; with ps select code_addr <= std_logic_vector(movc_addr) when movc_pc_0 | movc_dptr_0, std_logic_vector(PC_reg) when others; ---- MOVC logic ---------------------------------------------------------------- acc_ext16 <= (X"00") & A_reg; with ps select movc_base <= PC_reg when movc_pc_0, DPTR_reg when others; movc_addr <= movc_base + acc_ext16; -- This register will not always hold DPTR+A, at times it will hold PC+A. In the -- state in which it will be used, it will be DPTR+A. registered_dptr_plus_a: process(clk) begin if clk'event and clk='1' then dptr_plus_a_reg <= movc_addr; end if; end process registered_dptr_plus_a; --## 6.- Conditional jump logic ################################################ cjne_condition <= not alu_result_is_zero; -- FIXME redundant, remove with jump_cond_sel_reg select jump_condition <= '1' when CC_ALWAYS, not alu_result_is_zero when CC_NZ, alu_result_is_zero when CC_Z, not acc_is_zero when CC_ACCNZ, acc_is_zero when CC_ACCZ, cjne_condition when CC_CJNE, PSW(7) when CC_C, not PSW(7) when CC_NC, bit_input when CC_BIT, not bit_input when CC_NOBIT, '0' when others; --## 7.- Address registers ##################################################### ---- Address 0 and 1 registers ------------------------------------------------- -- addr0_reg is the most frequent source of IRAM/SFR addresses and is used as -- an aux reg in jumps and rets. -- Decide when to load the address register... with ps select load_addr0 <= '1' when fetch_addr_0, '1' when fetch_addr_0_ajmp, '1' when irq_2, '1' when acall_0 | lcall_1, '1' when load_rel, '1' when cjne_a_imm_1, '1' when cjne_a_dir_0, '1' when cjne_a_dir_2, '1' when cjne_ri_imm_1, '1' when cjne_ri_imm_4, '1' when cjne_rn_imm_2, '1' when alu_xchd_1, '1' when djnz_dir_0, '1' when djnz_dir_3, '1' when djnz_rn_0, '1' when jrb_bit_0, '1' when jrb_bit_3, '1' when bit_op_0, '1' when pop_1, '1' when ret_2, '1' when alu_rx_to_ab, '1' when movx_a_ri_1, '1' when movx_ri_a_1, '1' when xch_dir_0, '1' when xch_rx_0, '1' when xch_rn_0, '1' when xch_rx_1, '1' when alu_ram_to_ar, '1' when alu_ram_to_t_code_to_ab, '1' when alu_code_to_ab, '1' when alu_res_to_ram_code_to_ab, '1' when alu_ram_to_t_rx_to_ab, --'1' when alu_res_to_ram_ram_to_ab, '1' when alu_ram_to_ar_2, '1' when alu_code_to_t_rx_to_ab, '0' when others; -- ...and decide what to load into it. with ps select addr0_reg_input <= iram_sfr_rd when alu_ram_to_ar, iram_sfr_rd when alu_ram_to_ar_2, iram_sfr_rd when cjne_ri_imm_1, iram_sfr_rd when alu_xchd_1, iram_sfr_rd when movx_a_ri_1, iram_sfr_rd when movx_ri_a_1, iram_sfr_rd when xch_rx_0, iram_sfr_rd when xch_rx_1, iram_sfr_rd when ret_2, "00" & irq_vector when irq_2, iram_sfr_addr when others; -- Auxiliary address registers 0 and 1 plus flag bit_index_reg address_registers: process(clk) begin if clk'event and clk='1' then if load_addr0='1' then -- Used to address IRAM/SCR and XRAM addr0_reg <= addr0_reg_input; -- The bit index is registered at the same time for use by bit ops. -- Signal bit_index is valid at the same time as addr0_reg_input. bit_index_reg <= bit_index; end if; if ps = lcall_0 or ps = fetch_addr_1 then addr1_reg <= unsigned(code_rd); elsif ps = irq_2 then addr1_reg <= (others => '0'); elsif ps = ret_1 then addr1_reg <= iram_sfr_rd; end if; end if; end process address_registers; ---- Opcode register(s) and signals directly derived from the opcode ----------- -- These register holds the instruction opcode byte. absolute_jump_block_register: process(clk) begin if clk'event and clk='1' then if ps=decode_0 then block_reg <= unsigned(code_rd(7 downto 5)); end if; end if; end process absolute_jump_block_register; -- Unregistered dir address; straight from code memory. code_byte <= unsigned(code_rd); -- Index of bit within byte. Will be registered along with bit_addr. bit_index <= unsigned(code_rd(2 downto 0)); -- Address of the byte containing the operand bit, if any. with code_rd(7) select bit_addr <= "0010" & unsigned(code_rd(6 downto 3)) when '0', "1" & unsigned(code_rd(6 downto 3)) & "000" when others; ---- Rn and @Ri addresses and multiplexor -------------------------------------- ri_addr <= "000" & PSW_reg(4 downto 3) & "00" & rn_index(0); rn_addr <= "000" & PSW_reg(4 downto 3) & rn_index; -- This logic only gets evaluated in state decode_0; and it needs to be valid -- only for Rn and @Ri instructions, otherwise it is not evaluated. -- Does the ALU instruction, if any, use @Ri? with uc_alu_class_decode_0 select alu_use_ri_by_class <= '1' when AC_A_RI_to_A, '1' when AC_RI_to_A, '1' when AC_RI_to_RI, '1' when AC_RI_to_D, '1' when AC_D_to_RI, '1' when AC_I_to_RI, '1' when AC_A_to_RI, '0' when others; -- The instruction uses @Ri unless it uses Rn. -- This signal gets registered as use_ri_reg in state decode_0. alu_use_ri <= '0' when code_rd(3)='1' else alu_use_ri_by_class; non_alu_use_ri <= '1' when ucode(11 downto 10)="10" else '0'; use_ri <= alu_use_ri when ucode(15 downto 14)="00" else non_alu_use_ri; -- This is the actual Rn/Ri multiplexor. rx_addr <= ri_addr when use_ri_reg='1' else rn_addr; --## 8.- SFR interface ######################################################### -- Assert sfr_vma when a SFR read or write cycle is going on (address valid). -- FIXME some of these are not read cycles but the cycle after! with ps select sfr_vma_internal <= sfr_addressing when alu_ar_to_ab, sfr_addressing when alu_ram_to_t, sfr_addressing when alu_ram_to_t_code_to_ab, sfr_addressing when alu_ram_to_v_code_to_t, sfr_addressing when alu_res_to_ram, sfr_addressing when alu_res_to_ram_code_to_ab, sfr_addressing when alu_res_to_ram_ar_to_ab, sfr_addressing when djnz_dir_1, sfr_addressing when djnz_dir_2, sfr_addressing when cjne_ri_imm_3, sfr_addressing when cjne_ri_imm_2, -- FIXME these are corrected states, the above may be bad sfr_addressing when cjne_a_dir_0, sfr_addressing when jrb_bit_0, sfr_addressing when bit_op_0, sfr_addressing when bit_op_2, sfr_addressing when xch_1, sfr_addressing when xch_2, sfr_addressing when alu_xchd_2, -- FIXME some other states missing '0' when others; -- Assert sfr_we_internal when a SFR write cycle is done. -- FIXME there should be a direct_we, not separate decoding for iram/sfr with ps select sfr_we_internal <= sfr_addressing when alu_res_to_ram, sfr_addressing when alu_res_to_ram_code_to_ab, sfr_addressing when alu_res_to_ram_ar_to_ab, sfr_addressing when djnz_dir_2, sfr_addressing when bit_op_2, sfr_addressing when jrb_bit_2, sfr_addressing when pop_2, '1' when mov_dptr_1, '1' when mov_dptr_2, sfr_addressing when xch_2, '0' when others; -- The SFR address is the full 8 address bits; even if we know there are no -- SFRs in the 00h..7fh range. sfr_addr_internal <= iram_sfr_addr; sfr_addr <= std_logic_vector(sfr_addr_internal); -- Data written into the internal or externa SFR is the IRAM input data. sfr_wr_internal <= bram_wr_data_p0; sfr_wr <= std_logic_vector(sfr_wr_internal); -- Internal and external SFR bus is identical. sfr_we <= sfr_we_internal; sfr_vma <= sfr_vma_internal; -- Internal SFR read multiplexor. Will be registered. with sfr_addr_internal select sfr_rd_internal <= PSW when SFR_ADDR_PSW, SP_reg when SFR_ADDR_SP, A_reg when SFR_ADDR_ACC, B_reg when SFR_ADDR_B, DPTR_reg(15 downto 8) when SFR_ADDR_DPH, DPTR_reg( 7 downto 0) when SFR_ADDR_DPL, IE_reg when SFR_ADDR_IE, IP_reg when SFR_ADDR_IP, unsigned(sfr_rd) when others; -- Registering the SFR read mux gives the SFR block the same timing behavior as -- the IRAM block, and improves clock rate a lot. SFR_mux_register: process(clk) begin if clk'event and clk='1' then sfr_rd_internal_reg <= sfr_rd_internal; sfr_addressing_reg <= sfr_addressing; end if; end process SFR_mux_register; -- Data read from the IRAM/SFR: this is the IRAM vs. SFR multiplexor. -- Note it is controlled with sfr_addressing_reg, which is in sync with both -- sfr_rd_internal_reg and bram_data_p0 because of the 1-cycle data latency -- of the BRAM and the SFR interface. iram_sfr_rd <= sfr_rd_internal_reg when sfr_addressing_reg='1' else bram_data_p0; --## 9.- PSW register and flag logic ########################################### -- PSW flag update enable. with ps select update_psw_flags <= -- Flags are updated at the same time ACC/RAM/SFR is loaded... '1' when alu_res_to_a, '1' when alu_res_to_ram, '1' when alu_res_to_ram_code_to_ab, '1' when alu_res_to_ram_ar_to_ab, '1' when alu_daa_1, -- (XCHD states included for generality only; they never -- update any flags (FM_NONE)). '1' when alu_xchd_4 | alu_xchd_5, -- ...when the CJNE magnitude comparison is made... '1' when cjne_a_imm_1, '1' when cjne_a_dir_2, '1' when cjne_ri_imm_4, '1' when cjne_rn_imm_2, -- ...when C is updated due by bit operation... '1' when bit_res_to_c, -- ...and when a mul/div is done. mul_ready when alu_mul_0, div_ready when alu_div_0, -- Note some '0' when others; -- PSW write enable for SFR accesses. load_psw <= '1' when sfr_addr_internal=SFR_ADDR_PSW and sfr_we_internal='1' else '0'; PSW_register: process(clk) begin if clk'event and clk='1' then if reset='1' then PSW_reg <= (others => '0'); elsif load_psw = '1' then PSW_reg <= alu_result(7 downto 1); elsif update_psw_flags = '1' then -- C flag if flag_mask_reg /= FM_NONE then PSW_reg(7) <= alu_cy; end if; -- OV flag if flag_mask_reg = FM_C_OV or flag_mask_reg = FM_ALL then PSW_reg(2) <= alu_ov; end if; -- AC flag if flag_mask_reg = FM_ALL then PSW_reg(6) <= alu_ac; end if; end if; end if; end process PSW_register; -- Note that P flag (bit 0) is registered separately. Join flags up here. PSW <= PSW_reg(7 downto 1) & alu_p; --## 10.- Stack logic ########################################################## -- SP write enable for SFR accesses. load_sp <= '1' when sfr_addr_internal=SFR_ADDR_SP and sfr_we_internal='1' else '0'; with ps select load_sp_implicit <= '1' when push_1 | pop_1, '1' when ret_0 | ret_1, '1' when acall_0 | acall_1 | lcall_1 | lcall_2, '1' when irq_1 | irq_2, '0' when others; update_sp <= load_sp or load_sp_implicit; with ps select SP_next <= SP_reg + 1 when push_1 | acall_0 | acall_1 | lcall_1 | lcall_2 | irq_1 | irq_2, SP_reg - 1 when pop_1 | ret_0 | ret_1, nobit_alu_result when others; stack_pointer: process(clk) begin if clk'event and clk='1' then if reset = '1' then SP_reg <= X"07"; else if update_sp = '1' then SP_reg <= SP_next; end if; end if; end if; end process stack_pointer; --## 11.- Datapath: ALU and ALU operand multiplexors ########################### -- ALU input operand mux control for ALU class instructions. Other instructions -- that use the ALU (CJNE, DJNZ...) will need to control those muxes. That logic -- is within the ALU module. -- Note that this signal gets registered for speed before being used. with uc_alu_class_decode_0 select alu_class_op_sel <= AI_A_T when AC_A_RI_to_A, AI_A_T when AC_A_RN_to_A, AI_A_T when AC_A_I_to_A, AI_A_T when AC_A_D_to_A, AI_A_T when AC_A_D_to_D, AI_V_T when AC_I_D_to_D, AI_A_0 when AC_A_to_RI, AI_A_0 when AC_A_to_D, AI_A_0 when AC_A_to_RN, AI_A_0 when AC_A_to_A, AI_T_0 when others; alu : entity work.light52_alu generic map ( IMPLEMENT_BCD_INSTRUCTIONS => IMPLEMENT_BCD_INSTRUCTIONS, SEQUENTIAL_MULTIPLIER => SEQUENTIAL_MULTIPLIER ) port map ( clk => clk, reset => reset, -- Data outputs result => alu_result, nobit_result => nobit_alu_result, bit_input_out => bit_input, -- Access to internal stuff ACC => A_reg, B => B_reg, -- XRAM, IRAM and CODE data interface xdata_wr => xdata_wr, xdata_rd => xdata_rd, code_rd => code_rd, iram_sfr_rd => iram_sfr_rd, -- Input and output flags cy_in => PSW_reg(7), ac_in => PSW_reg(6), cy_out => alu_cy, ov_out => alu_ov, ac_out => alu_ac, p_out => alu_p, acc_is_zero => acc_is_zero, result_is_zero => alu_result_is_zero, -- Control inputs use_bitfield => dpath_mux0_reg, alu_fn_reg => alu_fn_reg, bit_index_reg => bit_index_reg, op_sel => alu_class_op_sel_reg, load_acc_sfr => load_acc_sfr, load_b_sfr => load_b_sfr, mul_ready => mul_ready, div_ready => div_ready, ps => ps ); load_b_sfr <= '1' when (sfr_addr_internal=SFR_ADDR_B and sfr_we_internal='1') else '0'; load_acc_sfr <= '1' when (sfr_addr_internal=SFR_ADDR_ACC and sfr_we_internal='1') else '0'; --## 12.- DPTR and XDATA address generation #################################### -- FIXME this should be encapsulated so that a 2nd DPTR can be easily added. load_dph <= '1' when sfr_addr_internal=SFR_ADDR_DPH and sfr_we_internal='1' else '0'; load_dpl <= '1' when sfr_addr_internal=SFR_ADDR_DPL and sfr_we_internal='1' else '0'; inc_dptr <= '1' when ps=special_0 else '0'; DPTR_register: process(clk) begin if clk'event and clk='1' then if inc_dptr='1' then DPTR_reg <= DPTR_reg + 1; else if load_dph='1' then DPTR_reg(15 downto 8) <= nobit_alu_result; end if; if load_dpl='1' then DPTR_reg(7 downto 0) <= nobit_alu_result; end if; end if; end if; end process DPTR_register; with ps select xdata_addr <= X"00" & std_logic_vector(addr0_reg) when movx_ri_a_2, X"00" & std_logic_vector(addr0_reg) when movx_a_ri_2, std_logic_vector(DPTR_reg) when others; with ps select xdata_vma <= '1' when movx_dptr_a_0 | movx_a_dptr_0, '1' when movx_a_ri_2 | movx_ri_a_2, '0' when others; with ps select xdata_we <= '1' when movx_dptr_a_0, '1' when movx_ri_a_2, '0' when others; end architecture microcoded; -------------------------------------------------------------------------------- -- NOTES: -- -- @note1: Decoding of '2nd half' opcodes. -- The top half of the opcode table is decoded using the BRAM initialized -- as a decoding table. -- The bottom half of the table (Rn opcodes, rows 8 to 15) is very -- symmetric: you only need to decode the columns, and the opcode of each -- column is the same as that of row 7 (with a couple exceptions). -- This means we can replace the entire bottom half of the decoding table -- with some logic, combined with row 7 (or 5). Logic marked with @note1 -- has this purpose. -- -- @note2: Unnecessary reset values for data registers. -- Reset values are strictly unnecessary for data registers such as ACC (as -- opposed to control registers). They have been given a reset value only -- so that the simulations logs are identical to those of B51 software -- simulator. -- -- @note3: Adder/subtractor. -- The adder/subtractor is coded as a simple adder in which the subtrahend -- is optionally negated -- this is for portability across synth tools. -- -- @note4: End states of the instructions. -- All instructions end in either fetch_0 or fetch_1. State fetch_1 can be -- thus considered the first state all instructions have in common. It is -- this state that does the the interrupt check. -- In a future revision, many instructions may overlap fetch_0 and fetch_1 -- with their last states and the irq check will change. -- -- @note5: Use of ns (instead of ps) in pc_incremented. -- This is done because several states are 'shared' by more than one -- instruction (i.e. they belong to more than one state machine paths) so -- looking at the present state is not enough (Note that the *complete* -- state in fact includes ps and uc_class_decode_0). -- This hack simplifies the logic but hurts speed A LOT (like 10% or more). -- We should use a *cleaner* state machine; it'd be much larger but also -- simpler. -- -- @note6: State on which PC is incremented. -- PC is incremented in state decode_0 and not fetch_1 so that it is still -- valid in fetch_1 in case we have to push it for an interrupt response. --------------------------------------------------------------------------------
Go to most recent revision | Compare with Previous | Blame | View Log