URL
https://opencores.org/ocsvn/minsoc/minsoc/trunk
Subversion Repositories minsoc
[/] [minsoc/] [trunk/] [utils/] [contributions/] [gpio/] [rtl/] [minsoc_defines.v] - Rev 93
Go to most recent revision | Compare with Previous | Blame | View Log
// // Define FPGA manufacturer // //`define GENERIC_FPGA //`define ALTERA_FPGA `define XILINX_FPGA // // Define FPGA Model (comment all out for ALTERA) // //`define SPARTAN2 //`define SPARTAN3 //`define SPARTAN3E `define SPARTAN3A //`define VIRTEX //`define VIRTEX2 //`define VIRTEX4 //`define VIRTEX5 // // Memory // `define MEMORY_ADR_WIDTH 13 //MEMORY_ADR_WIDTH IS NOT ALLOWED TO BE LESS THAN 12, memory is composed by blocks of address width 11 //Address width of memory -> select memory depth, 2 powers MEMORY_ADR_WIDTH defines the memory depth //the memory data width is 32 bit, memory amount in Bytes = 4*memory depth // // Memory type (uncomment something if ASIC or generic memory) // //`define GENERIC_MEMORY //`define AVANT_ATP //`define VIRAGE_SSP //`define VIRTUALSILICON_SSP // // TAP selection // //`define GENERIC_TAP `define FPGA_TAP // // Clock Division selection // //`define NO_CLOCK_DIVISION //`define GENERIC_CLOCK_DIVISION `define FPGA_CLOCK_DIVISION //Altera ALTPLL is not implemented, didn't find the code for its verilog instantiation //if you selected altera and this, the GENERIC_CLOCK_DIVISION will be automatically taken // // Define division // `define CLOCK_DIVISOR 5 //in case of GENERIC_CLOCK_DIVISION the real value will be rounded down to an even value //in FPGA case, check minsoc_clock_manager for allowed divisors //DO NOT USE CLOCK_DIVISOR = 1 COMMENT THE CLOCK DIVISION SELECTION INSTEAD // // Reset polarity // //`define NEGATIVE_RESET; //rstn `define POSITIVE_RESET; //rst // // Start-up circuit (only necessary later to load firmware automatically from SPI memory) // //`define START_UP // // Connected modules // `define UART //`define ETHERNET `define GPIO // // Ethernet reset // //`define ETH_RESET 1'b0 `define ETH_RESET 1'b1 // // GPIO Pins // `define GPIO_HAS_INPUT_PINS //`define GPIO_HAS_OUTPUT_PINS `define GPIO_HAS_BIDIR_PINS `define GPIO_NUM_INPUT 4'd8 `define GPIO_NUM_OUTPUT 4'd0 `define GPIO_NUM_BIDIR 4'd8 // // Interrupts // `define APP_INT_RES1 1:0 `define APP_INT_UART 2 `define APP_INT_RES2 3 `define APP_INT_ETH 4 `define APP_INT_PS2 5 `define APP_INT_GPIO 6 `define APP_INT_RES3 19:7 // // Address map // `define APP_ADDR_DEC_W 8 `define APP_ADDR_SRAM `APP_ADDR_DEC_W'h00 `define APP_ADDR_FLASH `APP_ADDR_DEC_W'h04 `define APP_ADDR_DECP_W 4 `define APP_ADDR_PERIP `APP_ADDR_DECP_W'h9 `define APP_ADDR_SPI `APP_ADDR_DEC_W'h97 `define APP_ADDR_ETH `APP_ADDR_DEC_W'h92 `define APP_ADDR_AUDIO `APP_ADDR_DEC_W'h9d `define APP_ADDR_UART `APP_ADDR_DEC_W'h90 `define APP_ADDR_PS2 `APP_ADDR_DEC_W'h94 `define APP_ADDR_GPIO `APP_ADDR_DEC_W'h9e `define APP_ADDR_RES2 `APP_ADDR_DEC_W'h9f // // Set-up GENERIC_TAP, GENERIC_MEMORY if GENERIC_FPGA was chosen // and GENERIC_CLOCK_DIVISION if NO_CLOCK_DIVISION was not set // `ifdef GENERIC_FPGA `define GENERIC_TAP `define GENERIC_MEMORY `ifndef NO_CLOCK_DIVISION `define GENERIC_CLOCK_DIVISION `endif `endif
Go to most recent revision | Compare with Previous | Blame | View Log