Subversion Repositories mips_enhanced

------------------------------------------------------------------------------
--  This file is a part of the GRLIB VHDL IP LIBRARY
--  Copyright (C) 2003, Gaisler Research
--
--  This program is free software; you can redistribute it and/or modify
--  it under the terms of the GNU General Public License as published by
--  the Free Software Foundation; either version 2 of the License, or
--  (at your option) any later version.
--
--  This program is distributed in the hope that it will be useful,
--  but WITHOUT ANY WARRANTY; without even the implied warranty of
--  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
--  GNU General Public License for more details.
--
--  You should have received a copy of the GNU General Public License
--  along with this program; if not, write to the Free Software
--  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA 
-----------------------------------------------------------------------------
-- Entity: 	dcom_uart
-- File:	dcom_uart.vhd
-- Author:	Jiri Gaisler - Gaisler Research
-- Description:	Asynchronous UART with baud-rate detection.
------------------------------------------------------------------------------
 
library ieee;
use ieee.std_logic_1164.all;
library grlib;
use grlib.amba.all;
use grlib.stdlib.all;
use grlib.devices.all;
library gaisler;
use gaisler.libdcom.all;
use gaisler.uart.all;
--pragma translate_off
use std.textio.all;
--pragma translate_on
 
entity dcom_uart is
  generic (
    pindex : integer := 0;
    paddr  : integer := 0;
    pmask  : integer := 16#fff#
  );
  port (
    rst    : in  std_ulogic;
    clk    : in  std_ulogic;
    ui     : in  uart_in_type;
    uo     : out uart_out_type;
    apbi   : in  apb_slv_in_type;
    apbo   : out apb_slv_out_type;
    uarti  : in  dcom_uart_in_type;
    uarto  : out dcom_uart_out_type
  );
end; 
 
architecture rtl of dcom_uart is
 
constant REVISION : integer := 0;
 
constant pconfig : apb_config_type := (
  0 => ahb_device_reg ( VENDOR_GAISLER, GAISLER_AHBUART, 0, REVISION, 0),
  1 => apb_iobar(paddr, pmask));
 
type rxfsmtype is (idle, startbit, data, stopbit);
type txfsmtype is (idle, data, stopbit);
 
type uartregs is record
  rxen   	:  std_ulogic;	-- receiver enabled
  dready    	:  std_ulogic;	-- data ready
  rsempty   	:  std_ulogic;	-- receiver shift register empty (internal)
  tsempty   	:  std_ulogic;	-- transmitter shift register empty
  thempty   	:  std_ulogic;	-- transmitter hold register empty
  break  	:  std_ulogic;	-- break detected
  ovf    	:  std_ulogic;	-- receiver overflow
  frame     	:  std_ulogic;	-- framing error
  rhold 	:  std_logic_vector(7 downto 0);
  rshift	:  std_logic_vector(7 downto 0);
  tshift	:  std_logic_vector(10 downto 0);
  thold 	:  std_logic_vector(7 downto 0);
  txstate	:  txfsmtype;
  txclk 	:  std_logic_vector(2 downto 0);  -- tx clock divider
  txtick     	:  std_ulogic;	-- tx clock (internal)
  rxstate	:  rxfsmtype;
  rxclk 	:  std_logic_vector(2 downto 0); -- rx clock divider
  rxdb  	:  std_ulogic;   -- rx data filtering buffer
  rxtick     	:  std_ulogic;	-- rx clock (internal)
  tick     	:  std_ulogic;	-- rx clock (internal)
  scaler	:  std_logic_vector(17 downto 0);
  brate 	:  std_logic_vector(17 downto 0);
  tcnt  	:  std_logic_vector(1 downto 0); -- autobaud counter
  rxdb2  	:  std_ulogic;   -- delayed rx data
  rxf    	:  std_logic_vector(7 downto 0); --  rx data filtering buffer
  fedge  	:  std_ulogic;   -- rx falling edge
end record;
 
signal r, rin : uartregs;
 
begin
 
  uartop : process(rst, r, apbi, uarti, ui )
  variable rdata : std_logic_vector(31 downto 0);
  variable scaler : std_logic_vector(17 downto 0);
  variable rxclk, txclk : std_logic_vector(2 downto 0);
  variable irxd : std_ulogic;
  variable v : uartregs;
 
  begin
 
    v := r;
    v.txtick := '0'; v.rxtick := '0'; v.tick := '0'; rdata := (others => '0');
 
-- scaler
 
    if r.tcnt = "11" then scaler := r.scaler - 1;
    else scaler := r.scaler + 1; end if;
 
    v.rxdb2 := r.rxdb;
    if r.tcnt /= "11" then
      if (r.rxdb2 and not r.rxdb) = '1' then v.fedge := '1'; end if;
      if (r.fedge) = '1' then 
	v.scaler := scaler;
	if (v.scaler(17) and not r.scaler(16)) = '1' then
	  v.scaler := "111111111111111011";
	  v.fedge := '0'; v.tcnt := "00";
	end if;
      end if;
      if (r.rxdb2 and r.fedge and not r.rxdb) = '1' then
	if (r.brate(17 downto 4)> r.scaler(17 downto 4)) then 
	  v.brate := r.scaler; v.tcnt := "00";
	end if;
	v.scaler := "111111111111111011";
	if (r.brate(17 downto 4) = r.scaler(17 downto 4)) then 
	  v.tcnt := r.tcnt + 1;
	  if r.tcnt = "10" then 
	    v.brate := "0000" & r.scaler(17 downto 4);
	    v.scaler := v.brate; v.rxen := '1';
          end if;
        end if;
      end if;
    else
      if (r.break and r.rxdb2) = '1' then
	v.scaler := "111111111111111011";
	v.brate := (others => '1'); v.tcnt := "00";
 	v.break := '0'; v.rxen := '0';
      end if;
    end if;
 
    if r.rxen = '1' then
      v.scaler := scaler;
      v.tick := scaler(15) and not r.scaler(15);
      if v.tick = '1' then v.scaler := r.brate; end if;
    end if;
 
-- read/write registers
 
    if uarti.read = '1' then v.dready := '0'; end if;
 
    case apbi.paddr(3 downto 2) is
    when "01" => 
      rdata(6 downto 0) := r.frame & '0' & r.ovf & 
		r.break & r.thempty & r.tsempty & r.dready;
    when "10" => 
      rdata(1 downto 0) := (r.tcnt(1) or r.tcnt(0)) & r.rxen;
    when others => 
      rdata(17 downto 0) := r.brate;
    end case;
 
    if (apbi.psel(pindex) and apbi.penable and apbi.pwrite) = '1' then
      case apbi.paddr(3 downto 2) is
      when "01" =>
	v.frame  := apbi.pwdata(6);
	v.ovf 	 := apbi.pwdata(4);
	v.break  := apbi.pwdata(3);
      when "10" => 
	v.tcnt 	 := apbi.pwdata(1) & apbi.pwdata(1);
	v.rxen 	 := apbi.pwdata(0);
      when "11" =>
	v.brate := apbi.pwdata(17 downto 0);
	v.scaler := apbi.pwdata(17 downto 0);
      when others =>
      end case;
    end if;
 
-- tx clock
 
    txclk := r.txclk + 1;
    if r.tick = '1' then
      v.txclk := txclk; v.txtick := r.txclk(2) and not txclk(2);
    end if;
 
-- rx clock
 
    rxclk := r.rxclk + 1;
    if r.tick = '1' then
      v.rxclk := rxclk; v.rxtick := r.rxclk(2) and not rxclk(2);
    end if;
 
-- filter rx data
 
    v.rxf := r.rxf(6 downto 0) & ui.rxd;
    if ((r.rxf(7) & r.rxf(7) & r.rxf(7) & r.rxf(7) & r.rxf(7) & r.rxf(7) &
	 r.rxf(7)) = r.rxf(6 downto 0))
    then v.rxdb := r.rxf(7); end if;
 
    irxd := r.rxdb;
 
-- transmitter operation
 
    case r.txstate is
    when idle =>	-- idle state
      if (r.txtick = '1') then v.tsempty := '1'; end if;
      if (r.rxen and (not r.thempty) and r.txtick) = '1' then 
	v.tshift := "10" & r.thold & '0'; v.txstate := data; 
	v.thempty := '1';
	v.tsempty := '0'; v.txclk := "00" & r.tick; v.txtick := '0';
      end if;
    when data =>	-- transmitt data frame
      if r.txtick = '1' then
	v.tshift := '1' & r.tshift(10 downto 1);
        if r.tshift(10 downto 1) = "1111111110" then
	v.tshift(0) := '1'; v.txstate := stopbit;
	end if;
      end if;
    when stopbit =>	-- transmitt stop bit
      if r.txtick = '1' then
	v.tshift := '1' & r.tshift(10 downto 1); v.txstate := idle;
      end if;
 
    end case;
 
-- writing of tx data register must be done after tx fsm to get correct
-- operation of thempty flag
 
    if uarti.write = '1' then
      v.thold := uarti.data(7 downto 0); v.thempty := '0';
    end if;
 
-- receiver operation
 
    case r.rxstate is
    when idle =>	-- wait for start bit
      if ((not r.rsempty) and not r.dready) = '1' then
	v.rhold := r.rshift; v.rsempty := '1'; v.dready := '1';
      end if;
      if (r.rxen and r.rxdb2 and (not irxd)) = '1' then
	v.rxstate := startbit; v.rshift := (others => '1'); v.rxclk := "100";
	if v.rsempty = '0' then v.ovf := '1'; end if;
	v.rsempty := '0'; v.rxtick := '0';
      end if;
    when startbit =>	-- check validity of start bit
      if r.rxtick = '1' then
	if irxd = '0' then 
	  v.rshift := irxd & r.rshift(7 downto 1); v.rxstate := data;
	else
	  v.rxstate := idle;
        end if;
      end if;
    when data =>	-- receive data frame
      if r.rxtick = '1' then
	v.rshift := irxd & r.rshift(7 downto 1); 
	if r.rshift(0) = '0' then
	v.rxstate := stopbit;
	end if;
      end if;
    when stopbit =>	-- receive stop bit
      if r.rxtick = '1' then
	if irxd = '1' then
	  v.rsempty := '0';
	  if v.dready = '0' then
	    v.rhold := r.rshift; v.rsempty := '1'; v.dready := '1';
	  end if;
	else
	  if r.rshift = "00000000" then
	    v.break := '1'; 		 -- break
	  else
	    v.frame := '1'; 		 -- framing error
	  end if;
	  v.rsempty := '1';
	end if;
        v.rxstate := idle;
      end if;
 
    end case;
 
-- reset operation
 
    if rst = '0' then 
      v.frame := '0'; v.rsempty := '1';
      v.ovf := '0'; v.break := '0'; v.thempty := '1';
      v.tsempty := '1'; v.dready := '0'; v.fedge := '0';
      v.txstate := idle; v.rxstate := idle; v.tshift(0) := '1';
      v.scaler := "111111111111111011"; v.brate := (others => '1'); 
      v.rxen := '0'; v.tcnt := "00";
      v.txclk := (others => '0'); v.rxclk := (others => '0');
    end if;
 
-- update registers
 
    rin <= v;
 
-- drive outputs
    uo.txd <= r.tshift(0);
    uo.scaler <= r.brate;
    uo.rtsn <= '0';
    uarto.dready <= r.dready;
    uarto.tsempty <= r.tsempty;
    uarto.thempty <= r.thempty;
    uarto.lock <= r.tcnt(1) and  r.tcnt(0);
    uarto.enable <= r.rxen;
    uarto.data <= r.rhold;
 
    apbo.prdata <= rdata;
 
  end process;
 
  apbo.pirq <= (others => '0');
  apbo.pconfig <= pconfig;
  apbo.pindex <= pindex;
 
  regs : process(clk)
  begin if rising_edge(clk) then r <= rin; end if; end process;
 
end;