Subversion Repositories neorv32

<<<
:sectnums:
==== Watchdog Timer (WDT)

[cols="<3,<3,<4"]
[frame="topbot",grid="none"]
|=======================
| Hardware source file(s): | neorv32_wdt.vhd | 
| Software driver file(s): | neorv32_wdt.c |
|                          | neorv32_wdt.h |
| Top entity port:         | none | 
| Configuration generics:  | _IO_WDT_EN_ | implement watchdog when _true_
| CPU interrupts:          | fast IRQ channel 0 | watchdog timer overflow (see <<_processor_interrupts>>)
|=======================


**Theory of Operation**

The watchdog (WDT) provides a last resort for safety-critical applications. The WDT has an internal 20-bit
wide counter that needs to be reset every now and then by the user program. If the counter overflows, either
a system reset or an interrupt is generated (depending on the configured operation mode).
The _WDT_CTRL_HALF_ flag of the control register `CTRL` indicates that at least half of the maximum timeout
value has been reached.

The watchdog is enabled by setting the _WDT_CTRL_EN_ bit. The clock used to increment the internal counter
is selected via the 3-bit _WDT_CTRL_CLK_SELx_ prescaler:

[cols="^3,^3,>4"]
[options="header",grid="rows"]
|=======================
| **`WDT_CTRL_CLK_SELx`** | Main clock prescaler | Timeout period in clock cycles
| `0b000` | 2 | 2 097 152
| `0b001` | 4 | 4 194 304
| `0b010` | 8 | 8 388 608
| `0b011` | 64 | 67 108 864
| `0b100` | 128 | 134 217 728
| `0b101` | 1024 | 1 073 741 824
| `0b110` | 2048 | 2 147 483 648
| `0b111` | 4096 | 4 294 967 296
|=======================

Whenever the internal timer overflows the watchdog executes one of two possible actions: Either a hard
processor reset is triggered or an interrupt is requested at CPU's fast interrupt channel #0. The
WDT_CTRL_MODE bit defines the action to be taken on an overflow: When cleared, the Watchdog will assert an
IRQ, when set the WDT will cause a system reset. The configured action can also be triggered manually at
any time by setting the _WDT_CTRL_FORCE_ bit. The watchdog is reset by setting the _WDT_CTRL_RESET_ bit.

A watchdog interrupt can only occur if the watchdog is enabled and interrupt mode is enabled.
A triggered interrupt has to be cleared again by writing zero to the according <<_mip>> CSR bit.

The cause of the last action of the watchdog can be determined via the _WDT_CTRL_RCAUSE_ flag. If this flag is
zero, the processor has been reset via the external reset signal. If this flag is set the last system reset was
initiated by the watchdog.

The Watchdog control register can be locked in order to protect the current configuration. The lock is
activated by setting bit _WDT_CTRL_LOCK_. In the locked state any write access to the configuration flags is
ignored (see table below, "writable if locked"). Read accesses to the control register are not effected. The
lock can only be removed by a system reset (via external reset signal or via a watchdog reset action).

.Watchdog Operation during Debugging
[IMPORTANT]
By default the watchdog pauses operation when the CPU enters debug mode and will resume normal operation after
the CPU has left debug mode. This will prevent an unintended watchdog timeout (and a hardware reset if configured)
during a debug session. However, the watchdog can be configured to keep operating even when the CPU is in debug
mode by setting the control register's _WDT_CTRL_DBEN_ bit. If the CPU's debug mode is not implemented this flag
is hardwired to zero.


.WDT register map (`struct NEORV32_WDT`)
[cols="<2,<2,<4,^1,^1,^2,<4"]
[options="header",grid="all"]
|=======================
| Address | Name [C] | Bit(s), Name [C] | R/W | Reset value | Writable if locked | Function
.11+<| `0xffffffbc` .11+<| `NEORV32_WDT.CTRL` <|`0` _WDT_CTRL_EN_       ^| r/w ^| `0` ^| no  <| watchdog enable
                                              <|`1` _WDT_CTRL_CLK_SEL0_ ^| r/w ^| `0` ^| no  .3+<| 3-bit clock prescaler select
                                              <|`2` _WDT_CTRL_CLK_SEL1_ ^| r/w ^| `0` ^| no 
                                              <|`3` _WDT_CTRL_CLK_SEL2_ ^| r/w ^| `0` ^| no 
                                              <|`4` _WDT_CTRL_MODE_     ^| r/w ^| `0` ^| no  <| overflow action: `1`=reset, `0`=IRQ
                                              <|`5` _WDT_CTRL_RCAUSE_   ^| r/- ^| `0` ^| -   <| cause of last system reset: `0`=caused by external reset signal, `1`=caused by watchdog
                                              <|`6` _WDT_CTRL_RESET_    ^| -/w ^| -   ^| yes <| watchdog reset when set, auto-clears
                                              <|`7` _WDT_CTRL_FORCE_    ^| -/w ^| -   ^| yes <| force configured watchdog action when set, auto-clears
                                              <|`8` _WDT_CTRL_LOCK_     ^| r/w ^| `0` ^| no  <| lock access to configuration when set, clears only on system reset (via external reset signal OR watchdog reset action = reset)
                                              <|`9` _WDT_CTRL_DBEN_     ^| r/w ^| `0` ^| no  <| allow WDT to continue operation even when in debug mode
                                              <|`10` _WDT_CTRL_HALF_    ^| r/- ^| `0` ^| -   <| set if at least half of the max. timeout counter value has been reached
|=======================