URL
https://opencores.org/ocsvn/open8_urisc/open8_urisc/trunk
Subversion Repositories open8_urisc
[/] [open8_urisc/] [trunk/] [VHDL/] [o8_elapsed_usec.vhd] - Rev 267
Go to most recent revision | Compare with Previous | Blame | View Log
-- Copyright (c)2020 Jeremy Seth Henry -- All rights reserved. -- -- Redistribution and use in source and binary forms, with or without -- modification, are permitted provided that the following conditions are met: -- * Redistributions of source code must retain the above copyright -- notice, this list of conditions and the following disclaimer. -- * Redistributions in binary form must reproduce the above copyright -- notice, this list of conditions and the following disclaimer in the -- documentation and/or other materials provided with the distribution, -- where applicable (as part of a user interface, debugging port, etc.) -- -- THIS SOFTWARE IS PROVIDED BY JEREMY SETH HENRY ``AS IS'' AND ANY -- EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED -- WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE -- DISCLAIMED. IN NO EVENT SHALL JEREMY SETH HENRY BE LIABLE FOR ANY -- DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES -- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; -- LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND -- ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT -- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF -- THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. -- -- VHDL Units : o8_elapsed_usec -- Description: Provides an 24-bit microsecond resolution counter for -- : measuring events -- -- Register Map: -- Offset Bitfield Description Read/Write -- 0x00 AAAAAAAA Req Interval Byte 0 (RW) -- 0x01 AAAAAAAA Req Interval Byte 1 (RW) -- 0x02 AAAAAAAA Req Interval Byte 2 (RW) -- 0x03 BA------ Control/Status Register (RW) -- A: Reset (1) (WR) -- B: Start (1) / Stop (0) -- -- Notes : Writing to 0x0 - 0x02 will latch the current value -- : Writing a 1 to bit A of 0x03 will cause an -- immediate timer reset. This bit is a one-shot. -- -- Revision History -- Author Date Change ------------------ -------- --------------------------------------------------- -- Seth Henry 04/20/20 Design Start -- Seth Henry 05/18/20 Added write qualification input library ieee; use ieee.std_logic_1164.all; use ieee.std_logic_unsigned.all; use ieee.std_logic_arith.all; use ieee.std_logic_misc.all; library work; use work.open8_pkg.all; entity o8_elapsed_usec is generic( Address : ADDRESS_TYPE ); port( Open8_Bus : in OPEN8_BUS_TYPE; Write_Qual : in std_logic := '1'; Rd_Data : out DATA_TYPE ); end entity; architecture behave of o8_elapsed_usec is alias Clock is Open8_Bus.Clock; alias Reset is Open8_Bus.Reset; alias uSec_Tick is Open8_Bus.uSec_Tick; constant User_Addr : std_logic_vector(15 downto 2) := Address(15 downto 2); alias Comp_Addr is Open8_Bus.Address(15 downto 2); signal Addr_Match : std_logic := '0'; alias Reg_Sel_d is Open8_Bus.Address(1 downto 0); signal Reg_Sel_q : std_logic_vector(1 downto 0) := "00"; signal Wr_En_d : std_logic := '0'; signal Wr_En_q : std_logic := '0'; alias Wr_Data_d is Open8_Bus.Wr_Data; signal Wr_Data_q : DATA_TYPE := x"00"; signal Rd_En_d : std_logic := '0'; signal Rd_En_q : std_logic := '0'; signal Shadow_Time : std_logic_vector(23 downto 0) := x"000000"; alias Shadow_Time_B0 is Shadow_Time( 7 downto 0); alias Shadow_Time_B1 is Shadow_Time(15 downto 8); alias Shadow_Time_B2 is Shadow_Time(23 downto 16); signal Update_Shadow : std_logic := '0'; signal Timer_Reset : std_logic := '0'; signal Timer_En_Req : std_logic := '0'; signal Timer_Enable : std_logic := '0'; signal Timer_Cnt : std_logic_vector(23 downto 0) := x"000000"; begin Addr_Match <= '1' when Comp_Addr = User_Addr else '0'; Wr_En_d <= Addr_Match and Open8_Bus.Wr_En; Rd_En_d <= Addr_Match and Open8_Bus.Rd_En; io_reg: process( Clock, Reset ) begin if( Reset = Reset_Level )then Reg_Sel_q <= "00"; Wr_En_q <= '0'; Wr_Data_q <= x"00"; Rd_En_q <= '0'; Rd_Data <= OPEN8_NULLBUS; Update_Shadow <= '0'; Timer_Reset <= '0'; Timer_En_Req <= '0'; elsif( rising_edge( Clock ) )then Reg_Sel_q <= Reg_Sel_d; Wr_En_q <= Wr_En_d; Wr_Data_q <= Wr_Data_d; Update_Shadow <= '0'; Timer_Reset <= '0'; if( Wr_En_q = '1' and Write_Qual = '1' )then case( Reg_Sel_q )is when "00" => Update_Shadow <= '1'; when "01" => Update_Shadow <= '1'; when "10" => Update_Shadow <= '1'; when "11" => Timer_Reset <= Wr_Data_q(6); Timer_En_Req <= Wr_Data_q(7); when others => null; end case; end if; Rd_Data <= OPEN8_NULLBUS; Rd_En_q <= Rd_En_d; if( Rd_En_q = '1' )then case( Reg_Sel_q )is when "00" => Rd_Data <= Shadow_Time_B0; when "01" => Rd_Data <= Shadow_Time_B1; when "10" => Rd_Data <= Shadow_Time_B2; when "11" => Rd_Data <= Timer_En_Req & "0000000"; when others => null; end case; end if; end if; end process; Timer_proc: process( Clock, Reset ) begin if( Reset = Reset_Level )then Shadow_Time <= x"000000"; Timer_Cnt <= x"000000"; elsif( rising_edge(Clock) )then if( Timer_Reset = '1' )then Timer_Cnt <= x"000000"; elsif( Timer_Enable = '1' )then Timer_Cnt <= Timer_Cnt + uSec_Tick; end if; if( uSec_Tick = '1' )then Timer_Enable <= Timer_En_Req; end if; if( Update_Shadow = '1' )then Shadow_Time <= Timer_Cnt; end if; end if; end process; end architecture;
Go to most recent revision | Compare with Previous | Blame | View Log