URL
https://opencores.org/ocsvn/open8_urisc/open8_urisc/trunk
Subversion Repositories open8_urisc
[/] [open8_urisc/] [trunk/] [VHDL/] [o8_gpin.vhd] - Rev 327
Go to most recent revision | Compare with Previous | Blame | View Log
-- Copyright (c)2011, 2019 Jeremy Seth Henry -- All rights reserved. -- -- Redistribution and use in source and binary forms, with or without -- modification, are permitted provided that the following conditions are met: -- * Redistributions of source code must retain the above copyright -- notice, this list of conditions and the following disclaimer. -- * Redistributions in binary form must reproduce the above copyright -- notice, this list of conditions and the following disclaimer in the -- documentation and/or other materials provided with the distribution, -- where applicable (as part of a user interface, debugging port, etc.) -- -- THIS SOFTWARE IS PROVIDED BY JEREMY SETH HENRY ``AS IS'' AND ANY -- EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED -- WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE -- DISCLAIMED. IN NO EVENT SHALL JEREMY SETH HENRY BE LIABLE FOR ANY -- DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES -- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; -- LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND -- ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT -- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF -- THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. -- -- VHDL Units : o8_gpin -- Description: Provides a single 8-bit input register -- -- Note: Cut the path between GPIN and GPIN_q1 for timing analysis -- -- Revision History -- Author Date Change ------------------ -------- --------------------------------------------------- -- Seth Henry 07/28/11 Design Start -- Seth Henry 12/19/19 Renamed to "o8_gpin" to fit "theme" -- Seth Henry 12/20/19 Added metastability registers -- Seth Henry 04/10/20 Code Cleanup -- Seth Henry 04/16/20 Modified to make use of Open8 bus record library ieee; use ieee.std_logic_1164.all; library work; use work.open8_pkg.all; entity o8_gpin is generic( Address : ADDRESS_TYPE ); port( Open8_Bus : in OPEN8_BUS_TYPE; Rd_Data : out DATA_TYPE; -- GPIN : in DATA_TYPE ); end entity; architecture behave of o8_gpin is alias Clock is Open8_Bus.Clock; alias Reset is Open8_Bus.Reset; constant User_Addr : std_logic_vector(15 downto 0) := Address; alias Comp_Addr is Open8_Bus.Address(15 downto 0); signal Addr_Match : std_logic; signal Rd_En_d : std_logic := '0'; signal Rd_En_q : std_logic := '0'; signal GPIN_q1 : DATA_TYPE; signal GPIN_q2 : DATA_TYPE; signal User_In : DATA_TYPE; begin Addr_Match <= '1' when Comp_Addr = User_Addr else '0'; Rd_En_d <= Addr_Match and Open8_Bus.Rd_En; io_reg: process( Clock, Reset ) begin if( Reset = Reset_Level )then Rd_En_q <= '0'; Rd_Data <= OPEN8_NULLBUS; GPIN_q1 <= x"00"; GPIN_q2 <= x"00"; User_In <= x"00"; elsif( rising_edge( Clock ) )then GPIN_q1 <= GPIN; GPIN_q2 <= GPIN_q1; User_In <= GPIN_q2; Rd_Data <= OPEN8_NULLBUS; Rd_En_q <= Rd_En_d; if( Rd_En_q = '1' )then Rd_Data <= User_In; end if; end if; end process; end architecture;
Go to most recent revision | Compare with Previous | Blame | View Log