Subversion Repositories openmsp430

//----------------------------------------------------------------------------
// Copyright (C) 2009 , Olivier Girard
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//     * Redistributions of source code must retain the above copyright
//       notice, this list of conditions and the following disclaimer.
//     * Redistributions in binary form must reproduce the above copyright
//       notice, this list of conditions and the following disclaimer in the
//       documentation and/or other materials provided with the distribution.
//     * Neither the name of the authors nor the names of its contributors
//       may be used to endorse or promote products derived from this software
//       without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
// OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
// THE POSSIBILITY OF SUCH DAMAGE
//
//----------------------------------------------------------------------------
//
// *File Name: omsp_dbg.v
//
// *Module Description:
//                       Debug interface
//
// *Author(s):
//              - Olivier Girard,    olgirard@gmail.com
//
//----------------------------------------------------------------------------
// $Rev: 202 $
// $LastChangedBy: olivier.girard $
// $LastChangedDate: 2015-07-01 23:13:32 +0200 (Wed, 01 Jul 2015) $
//----------------------------------------------------------------------------
`ifdef OMSP_NO_INCLUDE
`else
`include "openMSP430_defines.v"
`endif
 
module  omsp_dbg (
 
// OUTPUTs
    dbg_cpu_reset,                     // Reset CPU from debug interface
    dbg_freeze,                        // Freeze peripherals
    dbg_halt_cmd,                      // Halt CPU command
    dbg_i2c_sda_out,                   // Debug interface: I2C SDA OUT
    dbg_mem_addr,                      // Debug address for rd/wr access
    dbg_mem_dout,                      // Debug unit data output
    dbg_mem_en,                        // Debug unit memory enable
    dbg_mem_wr,                        // Debug unit memory write
    dbg_reg_wr,                        // Debug unit CPU register write
    dbg_uart_txd,                      // Debug interface: UART TXD
 
// INPUTs
    cpu_en_s,                          // Enable CPU code execution (synchronous)
    cpu_id,                            // CPU ID
    cpu_nr_inst,                       // Current oMSP instance number
    cpu_nr_total,                      // Total number of oMSP instances-1
    dbg_clk,                           // Debug unit clock
    dbg_en_s,                          // Debug interface enable (synchronous)
    dbg_halt_st,                       // Halt/Run status from CPU
    dbg_i2c_addr,                      // Debug interface: I2C Address
    dbg_i2c_broadcast,                 // Debug interface: I2C Broadcast Address (for multicore systems)
    dbg_i2c_scl,                       // Debug interface: I2C SCL
    dbg_i2c_sda_in,                    // Debug interface: I2C SDA IN
    dbg_mem_din,                       // Debug unit Memory data input
    dbg_reg_din,                       // Debug unit CPU register data input
    dbg_rst,                           // Debug unit reset
    dbg_uart_rxd,                      // Debug interface: UART RXD (asynchronous)
    decode_noirq,                      // Frontend decode instruction
    eu_mab,                            // Execution-Unit Memory address bus
    eu_mb_en,                          // Execution-Unit Memory bus enable
    eu_mb_wr,                          // Execution-Unit Memory bus write transfer
    fe_mdb_in,                         // Frontend Memory data bus input
    pc,                                // Program counter
    puc_pnd_set                        // PUC pending set for the serial debug interface
);
 
// OUTPUTs
//=========
output              dbg_cpu_reset;     // Reset CPU from debug interface
output              dbg_freeze;        // Freeze peripherals
output              dbg_halt_cmd;      // Halt CPU command
output              dbg_i2c_sda_out;   // Debug interface: I2C SDA OUT
output       [15:0] dbg_mem_addr;      // Debug address for rd/wr access
output       [15:0] dbg_mem_dout;      // Debug unit data output
output              dbg_mem_en;        // Debug unit memory enable
output        [1:0] dbg_mem_wr;        // Debug unit memory write
output              dbg_reg_wr;        // Debug unit CPU register write
output              dbg_uart_txd;      // Debug interface: UART TXD
 
// INPUTs
//=========
input               cpu_en_s;          // Enable CPU code execution (synchronous)
input        [31:0] cpu_id;            // CPU ID
input         [7:0] cpu_nr_inst;       // Current oMSP instance number
input         [7:0] cpu_nr_total;      // Total number of oMSP instances-1
input               dbg_clk;           // Debug unit clock
input               dbg_en_s;          // Debug interface enable (synchronous)
input               dbg_halt_st;       // Halt/Run status from CPU
input         [6:0] dbg_i2c_addr;      // Debug interface: I2C Address
input         [6:0] dbg_i2c_broadcast; // Debug interface: I2C Broadcast Address (for multicore systems)
input               dbg_i2c_scl;       // Debug interface: I2C SCL
input               dbg_i2c_sda_in;    // Debug interface: I2C SDA IN
input        [15:0] dbg_mem_din;       // Debug unit Memory data input
input        [15:0] dbg_reg_din;       // Debug unit CPU register data input
input               dbg_rst;           // Debug unit reset
input               dbg_uart_rxd;      // Debug interface: UART RXD (asynchronous)
input               decode_noirq;      // Frontend decode instruction
input        [15:0] eu_mab;            // Execution-Unit Memory address bus
input               eu_mb_en;          // Execution-Unit Memory bus enable
input         [1:0] eu_mb_wr;          // Execution-Unit Memory bus write transfer
input        [15:0] fe_mdb_in;         // Frontend Memory data bus input
input        [15:0] pc;                // Program counter
input               puc_pnd_set;       // PUC pending set for the serial debug interface
 
 
//=============================================================================
// 1)  WIRE & PARAMETER DECLARATION
//=============================================================================
 
// Diverse wires and registers
wire  [5:0] dbg_addr;
wire [15:0] dbg_din;
wire        dbg_wr;
reg         mem_burst;
wire        dbg_reg_rd;
wire        dbg_mem_rd;
reg         dbg_mem_rd_dly;
wire        dbg_swbrk;
wire        dbg_rd;
reg         dbg_rd_rdy;
wire        mem_burst_rd;
wire        mem_burst_wr;
wire        brk0_halt;
wire        brk0_pnd;
wire [15:0] brk0_dout;
wire        brk1_halt;
wire        brk1_pnd;
wire [15:0] brk1_dout;
wire        brk2_halt;
wire        brk2_pnd;
wire [15:0] brk2_dout;
wire        brk3_halt;
wire        brk3_pnd;
wire [15:0] brk3_dout;
 
// Number of registers
parameter           NR_REG       = 25;
 
// Register addresses
parameter           CPU_ID_LO    = 6'h00;
parameter           CPU_ID_HI    = 6'h01;
parameter           CPU_CTL      = 6'h02;
parameter           CPU_STAT     = 6'h03;
parameter           MEM_CTL      = 6'h04;
parameter           MEM_ADDR     = 6'h05;
parameter           MEM_DATA     = 6'h06;
parameter           MEM_CNT      = 6'h07;
`ifdef DBG_HWBRK_0
parameter           BRK0_CTL     = 6'h08;
parameter           BRK0_STAT    = 6'h09;
parameter           BRK0_ADDR0   = 6'h0A;
parameter           BRK0_ADDR1   = 6'h0B;
`endif
`ifdef DBG_HWBRK_1
parameter           BRK1_CTL     = 6'h0C;
parameter           BRK1_STAT    = 6'h0D;
parameter           BRK1_ADDR0   = 6'h0E;
parameter           BRK1_ADDR1   = 6'h0F;
`endif
`ifdef DBG_HWBRK_2
parameter           BRK2_CTL     = 6'h10;
parameter           BRK2_STAT    = 6'h11;
parameter           BRK2_ADDR0   = 6'h12;
parameter           BRK2_ADDR1   = 6'h13;
`endif
`ifdef DBG_HWBRK_3
parameter           BRK3_CTL     = 6'h14;
parameter           BRK3_STAT    = 6'h15;
parameter           BRK3_ADDR0   = 6'h16;
parameter           BRK3_ADDR1   = 6'h17;
`endif
parameter           CPU_NR       = 6'h18;
 
// Register one-hot decoder
parameter           BASE_D       = {{NR_REG-1{1'b0}}, 1'b1};
parameter           CPU_ID_LO_D  = (BASE_D << CPU_ID_LO);
parameter           CPU_ID_HI_D  = (BASE_D << CPU_ID_HI);
parameter           CPU_CTL_D    = (BASE_D << CPU_CTL);
parameter           CPU_STAT_D   = (BASE_D << CPU_STAT);
parameter           MEM_CTL_D    = (BASE_D << MEM_CTL);
parameter           MEM_ADDR_D   = (BASE_D << MEM_ADDR);
parameter           MEM_DATA_D   = (BASE_D << MEM_DATA);
parameter           MEM_CNT_D    = (BASE_D << MEM_CNT);
`ifdef DBG_HWBRK_0
parameter           BRK0_CTL_D   = (BASE_D << BRK0_CTL);
parameter           BRK0_STAT_D  = (BASE_D << BRK0_STAT);
parameter           BRK0_ADDR0_D = (BASE_D << BRK0_ADDR0);
parameter           BRK0_ADDR1_D = (BASE_D << BRK0_ADDR1);
`endif
`ifdef DBG_HWBRK_1
parameter           BRK1_CTL_D   = (BASE_D << BRK1_CTL);
parameter           BRK1_STAT_D  = (BASE_D << BRK1_STAT);
parameter           BRK1_ADDR0_D = (BASE_D << BRK1_ADDR0);
parameter           BRK1_ADDR1_D = (BASE_D << BRK1_ADDR1);
`endif
`ifdef DBG_HWBRK_2
parameter           BRK2_CTL_D   = (BASE_D << BRK2_CTL);
parameter           BRK2_STAT_D  = (BASE_D << BRK2_STAT);
parameter           BRK2_ADDR0_D = (BASE_D << BRK2_ADDR0);
parameter           BRK2_ADDR1_D = (BASE_D << BRK2_ADDR1);
`endif
`ifdef DBG_HWBRK_3
parameter           BRK3_CTL_D   = (BASE_D << BRK3_CTL);
parameter           BRK3_STAT_D  = (BASE_D << BRK3_STAT);
parameter           BRK3_ADDR0_D = (BASE_D << BRK3_ADDR0);
parameter           BRK3_ADDR1_D = (BASE_D << BRK3_ADDR1);
`endif
parameter           CPU_NR_D     = (BASE_D << CPU_NR);
 
 
//============================================================================
// 2)  REGISTER DECODER
//============================================================================
 
// Select Data register during a burst
wire  [5:0] dbg_addr_in = mem_burst ? MEM_DATA : dbg_addr;
 
// Register address decode
reg  [NR_REG-1:0]  reg_dec;
always @(dbg_addr_in)
  case (dbg_addr_in)
    CPU_ID_LO :  reg_dec  =  CPU_ID_LO_D;
    CPU_ID_HI :  reg_dec  =  CPU_ID_HI_D;
    CPU_CTL   :  reg_dec  =  CPU_CTL_D;
    CPU_STAT  :  reg_dec  =  CPU_STAT_D;
    MEM_CTL   :  reg_dec  =  MEM_CTL_D;
    MEM_ADDR  :  reg_dec  =  MEM_ADDR_D;
    MEM_DATA  :  reg_dec  =  MEM_DATA_D;
    MEM_CNT   :  reg_dec  =  MEM_CNT_D;
`ifdef DBG_HWBRK_0
    BRK0_CTL  :  reg_dec  =  BRK0_CTL_D;
    BRK0_STAT :  reg_dec  =  BRK0_STAT_D;
    BRK0_ADDR0:  reg_dec  =  BRK0_ADDR0_D;
    BRK0_ADDR1:  reg_dec  =  BRK0_ADDR1_D;
`endif
`ifdef DBG_HWBRK_1
    BRK1_CTL  :  reg_dec  =  BRK1_CTL_D;
    BRK1_STAT :  reg_dec  =  BRK1_STAT_D;
    BRK1_ADDR0:  reg_dec  =  BRK1_ADDR0_D;
    BRK1_ADDR1:  reg_dec  =  BRK1_ADDR1_D;
`endif
`ifdef DBG_HWBRK_2
    BRK2_CTL  :  reg_dec  =  BRK2_CTL_D;
    BRK2_STAT :  reg_dec  =  BRK2_STAT_D;
    BRK2_ADDR0:  reg_dec  =  BRK2_ADDR0_D;
    BRK2_ADDR1:  reg_dec  =  BRK2_ADDR1_D;
`endif
`ifdef DBG_HWBRK_3
    BRK3_CTL  :  reg_dec  =  BRK3_CTL_D;
    BRK3_STAT :  reg_dec  =  BRK3_STAT_D;
    BRK3_ADDR0:  reg_dec  =  BRK3_ADDR0_D;
    BRK3_ADDR1:  reg_dec  =  BRK3_ADDR1_D;
`endif
    CPU_NR    :  reg_dec  =  CPU_NR_D;
  // pragma coverage off
    default:     reg_dec  =  {NR_REG{1'b0}};
  // pragma coverage on
  endcase
 
// Read/Write probes
wire               reg_write =  dbg_wr;
wire               reg_read  =  1'b1;
 
// Read/Write vectors
wire  [NR_REG-1:0] reg_wr    = reg_dec & {NR_REG{reg_write}};
wire  [NR_REG-1:0] reg_rd    = reg_dec & {NR_REG{reg_read}};
 
 
//=============================================================================
// 3)  REGISTER: CORE INTERFACE
//=============================================================================
 
// CPU_ID Register
//-----------------
//              -------------------------------------------------------------------
// CPU_ID_LO:  | 15  14  13  12  11  10  9  |  8  7  6  5  4  |  3   |   2  1  0   |
//             |----------------------------+-----------------+------+-------------|
//             |        PER_SPACE           |   USER_VERSION  | ASIC | CPU_VERSION |
//              --------------------------------------------------------------------
// CPU_ID_HI:  |   15  14  13  12  11  10   |   9  8  7  6  5  4  3  2  1   |   0  |
//             |----------------------------+-------------------------------+------|
//             |         PMEM_SIZE          |            DMEM_SIZE          |  MPY |
//              -------------------------------------------------------------------
 
// This register is assigned in the SFR module
 
 
// CPU_NR Register
//-----------------
//    -------------------------------------------------------------------
//   | 15  14  13  12  11  10   9   8  |  7   6   5   4   3   2   1   0  |
//   |---------------------------------+---------------------------------|
//   |            CPU_TOTAL_NR         |           CPU_INST_NR           |
//    -------------------------------------------------------------------
 
wire [15:0] cpu_nr = {cpu_nr_total, cpu_nr_inst};
 
 
// CPU_CTL Register
//-----------------------------------------------------------------------------
//       7         6          5          4           3        2     1    0
//   Reserved   CPU_RST  RST_BRK_EN  FRZ_BRK_EN  SW_BRK_EN  ISTEP  RUN  HALT
//-----------------------------------------------------------------------------
reg   [6:3] cpu_ctl;
 
wire        cpu_ctl_wr = reg_wr[CPU_CTL];
 
always @ (posedge dbg_clk or posedge dbg_rst)
`ifdef DBG_RST_BRK_EN
  if (dbg_rst)         cpu_ctl <=  4'h6;
`else
  if (dbg_rst)         cpu_ctl <=  4'h2;
`endif
  else if (cpu_ctl_wr) cpu_ctl <=  dbg_din[6:3];
 
wire  [7:0] cpu_ctl_full = {1'b0, cpu_ctl, 3'b000};
 
wire        halt_cpu = cpu_ctl_wr & dbg_din[`HALT]  & ~dbg_halt_st;
wire        run_cpu  = cpu_ctl_wr & dbg_din[`RUN]   &  dbg_halt_st;
wire        istep    = cpu_ctl_wr & dbg_din[`ISTEP] &  dbg_halt_st;
 
 
// CPU_STAT Register
//------------------------------------------------------------------------------------
//      7           6          5           4           3         2      1       0
// HWBRK3_PND  HWBRK2_PND  HWBRK1_PND  HWBRK0_PND  SWBRK_PND  PUC_PND  Res.  HALT_RUN
//------------------------------------------------------------------------------------
reg   [3:2] cpu_stat;
 
wire        cpu_stat_wr  = reg_wr[CPU_STAT];
wire  [3:2] cpu_stat_set = {dbg_swbrk, puc_pnd_set};
wire  [3:2] cpu_stat_clr = ~dbg_din[3:2];
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)          cpu_stat <=  2'b00;
  else if (cpu_stat_wr) cpu_stat <= ((cpu_stat & cpu_stat_clr) | cpu_stat_set);
  else                  cpu_stat <=  (cpu_stat                 | cpu_stat_set);
 
wire  [7:0] cpu_stat_full = {brk3_pnd, brk2_pnd, brk1_pnd, brk0_pnd,
                             cpu_stat, 1'b0, dbg_halt_st};
 
 
//=============================================================================
// 4)  REGISTER: MEMORY INTERFACE
//=============================================================================
 
// MEM_CTL Register
//-----------------------------------------------------------------------------
//       7     6     5     4          3        2         1       0
//            Reserved               B/W    MEM/REG    RD/WR   START
//
// START  :  -  0 : Do nothing.
//           -  1 : Initiate memory transfer.
//
// RD/WR  :  -  0 : Read access.
//           -  1 : Write access.
//
// MEM/REG:  -  0 : Memory access.
//           -  1 : CPU Register access.
//
// B/W    :  -  0 : 16 bit access.
//           -  1 :  8 bit access (not valid for CPU Registers).
//
//-----------------------------------------------------------------------------
reg   [3:1] mem_ctl;
 
wire        mem_ctl_wr = reg_wr[MEM_CTL];
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)         mem_ctl <=  3'h0;
  else if (mem_ctl_wr) mem_ctl <=  dbg_din[3:1];
 
wire  [7:0] mem_ctl_full  = {4'b0000, mem_ctl, 1'b0};
 
reg         mem_start;
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)  mem_start <=  1'b0;
  else          mem_start <=  mem_ctl_wr & dbg_din[0];
 
wire        mem_bw    = mem_ctl[3];
 
// MEM_DATA Register
//------------------
reg  [15:0] mem_data;
reg  [15:0] mem_addr;
wire        mem_access;
 
wire        mem_data_wr = reg_wr[MEM_DATA];
 
wire [15:0] dbg_mem_din_bw = ~mem_bw      ? dbg_mem_din                :
                              mem_addr[0] ? {8'h00, dbg_mem_din[15:8]} :
                                            {8'h00, dbg_mem_din[7:0]};
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)             mem_data <=  16'h0000;
  else if (mem_data_wr)    mem_data <=  dbg_din;
  else if (dbg_reg_rd)     mem_data <=  dbg_reg_din;
  else if (dbg_mem_rd_dly) mem_data <=  dbg_mem_din_bw;
 
 
// MEM_ADDR Register
//------------------
reg  [15:0] mem_cnt;
 
wire        mem_addr_wr  = reg_wr[MEM_ADDR];
wire        dbg_mem_acc  = (|dbg_mem_wr | (dbg_rd_rdy & ~mem_ctl[2]));
wire        dbg_reg_acc  = ( dbg_reg_wr | (dbg_rd_rdy &  mem_ctl[2]));
 
wire [15:0] mem_addr_inc = (mem_cnt==16'h0000)                       ? 16'h0000 :
                           (mem_burst &  dbg_mem_acc & ~mem_bw)      ? 16'h0002 :
                           (mem_burst & (dbg_mem_acc | dbg_reg_acc)) ? 16'h0001 : 16'h0000;
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)          mem_addr <=  16'h0000;
  else if (mem_addr_wr) mem_addr <=  dbg_din;
  else                  mem_addr <=  mem_addr + mem_addr_inc;
 
// MEM_CNT Register
//------------------
 
wire        mem_cnt_wr  = reg_wr[MEM_CNT];
 
wire [15:0] mem_cnt_dec = (mem_cnt==16'h0000)                       ? 16'h0000 :
                          (mem_burst & (dbg_mem_acc | dbg_reg_acc)) ? 16'hffff : 16'h0000;
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)         mem_cnt <=  16'h0000;
  else if (mem_cnt_wr) mem_cnt <=  dbg_din;
  else                 mem_cnt <=  mem_cnt + mem_cnt_dec;
 
 
//=============================================================================
// 5)  BREAKPOINTS / WATCHPOINTS
//=============================================================================
 
`ifdef DBG_HWBRK_0
// Hardware Breakpoint/Watchpoint Register read select
wire [3:0] brk0_reg_rd = {reg_rd[BRK0_ADDR1],
                          reg_rd[BRK0_ADDR0],
                          reg_rd[BRK0_STAT],
                          reg_rd[BRK0_CTL]};
 
// Hardware Breakpoint/Watchpoint Register write select
wire [3:0] brk0_reg_wr = {reg_wr[BRK0_ADDR1],
                          reg_wr[BRK0_ADDR0],
                          reg_wr[BRK0_STAT],
                          reg_wr[BRK0_CTL]};
 
omsp_dbg_hwbrk dbg_hwbr_0 (
 
// OUTPUTs
    .brk_halt     (brk0_halt),    // Hardware breakpoint command
    .brk_pnd      (brk0_pnd),     // Hardware break/watch-point pending
    .brk_dout     (brk0_dout),    // Hardware break/watch-point register data input
 
// INPUTs
    .brk_reg_rd   (brk0_reg_rd),  // Hardware break/watch-point register read select
    .brk_reg_wr   (brk0_reg_wr),  // Hardware break/watch-point register write select
    .dbg_clk      (dbg_clk),      // Debug unit clock
    .dbg_din      (dbg_din),      // Debug register data input
    .dbg_rst      (dbg_rst),      // Debug unit reset
    .decode_noirq (decode_noirq), // Frontend decode instruction
    .eu_mab       (eu_mab),       // Execution-Unit Memory address bus
    .eu_mb_en     (eu_mb_en),     // Execution-Unit Memory bus enable
    .eu_mb_wr     (eu_mb_wr),     // Execution-Unit Memory bus write transfer
    .pc           (pc)            // Program counter
);
 
`else
assign      brk0_halt       =  1'b0;
assign      brk0_pnd        =  1'b0;
assign      brk0_dout       = 16'h0000;
wire [15:0] UNUSED_eu_mab   =  eu_mab;
wire        UNUSED_eu_mb_en =  eu_mb_en;
wire  [1:0] UNUSED_eu_mb_wr =  eu_mb_wr;
wire [15:0] UNUSED_pc       =  pc;
`endif
 
`ifdef DBG_HWBRK_1
// Hardware Breakpoint/Watchpoint Register read select
wire [3:0] brk1_reg_rd = {reg_rd[BRK1_ADDR1],
                          reg_rd[BRK1_ADDR0],
                          reg_rd[BRK1_STAT],
                          reg_rd[BRK1_CTL]};
 
// Hardware Breakpoint/Watchpoint Register write select
wire [3:0] brk1_reg_wr = {reg_wr[BRK1_ADDR1],
                          reg_wr[BRK1_ADDR0],
                          reg_wr[BRK1_STAT],
                          reg_wr[BRK1_CTL]};
 
omsp_dbg_hwbrk dbg_hwbr_1 (
 
// OUTPUTs
    .brk_halt     (brk1_halt),    // Hardware breakpoint command
    .brk_pnd      (brk1_pnd),     // Hardware break/watch-point pending
    .brk_dout     (brk1_dout),    // Hardware break/watch-point register data input
 
// INPUTs
    .brk_reg_rd   (brk1_reg_rd),  // Hardware break/watch-point register read select
    .brk_reg_wr   (brk1_reg_wr),  // Hardware break/watch-point register write select
    .dbg_clk      (dbg_clk),      // Debug unit clock
    .dbg_din      (dbg_din),      // Debug register data input
    .dbg_rst      (dbg_rst),      // Debug unit reset
    .decode_noirq (decode_noirq), // Frontend decode instruction
    .eu_mab       (eu_mab),       // Execution-Unit Memory address bus
    .eu_mb_en     (eu_mb_en),     // Execution-Unit Memory bus enable
    .eu_mb_wr     (eu_mb_wr),     // Execution-Unit Memory bus write transfer
    .pc           (pc)            // Program counter
);
 
`else
assign brk1_halt =  1'b0;
assign brk1_pnd  =  1'b0;
assign brk1_dout = 16'h0000;
`endif
 
 `ifdef DBG_HWBRK_2
// Hardware Breakpoint/Watchpoint Register read select
wire [3:0] brk2_reg_rd = {reg_rd[BRK2_ADDR1],
                          reg_rd[BRK2_ADDR0],
                          reg_rd[BRK2_STAT],
                          reg_rd[BRK2_CTL]};
 
// Hardware Breakpoint/Watchpoint Register write select
wire [3:0] brk2_reg_wr = {reg_wr[BRK2_ADDR1],
                          reg_wr[BRK2_ADDR0],
                          reg_wr[BRK2_STAT],
                          reg_wr[BRK2_CTL]};
 
omsp_dbg_hwbrk dbg_hwbr_2 (
 
// OUTPUTs
    .brk_halt     (brk2_halt),    // Hardware breakpoint command
    .brk_pnd      (brk2_pnd),     // Hardware break/watch-point pending
    .brk_dout     (brk2_dout),    // Hardware break/watch-point register data input
 
// INPUTs
    .brk_reg_rd   (brk2_reg_rd),  // Hardware break/watch-point register read select
    .brk_reg_wr   (brk2_reg_wr),  // Hardware break/watch-point register write select
    .dbg_clk      (dbg_clk),      // Debug unit clock
    .dbg_din      (dbg_din),      // Debug register data input
    .dbg_rst      (dbg_rst),      // Debug unit reset
    .decode_noirq (decode_noirq), // Frontend decode instruction
    .eu_mab       (eu_mab),       // Execution-Unit Memory address bus
    .eu_mb_en     (eu_mb_en),     // Execution-Unit Memory bus enable
    .eu_mb_wr     (eu_mb_wr),     // Execution-Unit Memory bus write transfer
    .pc           (pc)            // Program counter
);
 
`else
assign brk2_halt =  1'b0;
assign brk2_pnd  =  1'b0;
assign brk2_dout = 16'h0000;
`endif
 
`ifdef DBG_HWBRK_3
// Hardware Breakpoint/Watchpoint Register read select
wire [3:0] brk3_reg_rd = {reg_rd[BRK3_ADDR1],
                          reg_rd[BRK3_ADDR0],
                          reg_rd[BRK3_STAT],
                          reg_rd[BRK3_CTL]};
 
// Hardware Breakpoint/Watchpoint Register write select
wire [3:0] brk3_reg_wr = {reg_wr[BRK3_ADDR1],
                          reg_wr[BRK3_ADDR0],
                          reg_wr[BRK3_STAT],
                          reg_wr[BRK3_CTL]};
 
omsp_dbg_hwbrk dbg_hwbr_3 (
 
// OUTPUTs
    .brk_halt     (brk3_halt),    // Hardware breakpoint command
    .brk_pnd      (brk3_pnd),     // Hardware break/watch-point pending
    .brk_dout     (brk3_dout),    // Hardware break/watch-point register data input
 
// INPUTs
    .brk_reg_rd   (brk3_reg_rd),  // Hardware break/watch-point register read select
    .brk_reg_wr   (brk3_reg_wr),  // Hardware break/watch-point register write select
    .dbg_clk      (dbg_clk),      // Debug unit clock
    .dbg_din      (dbg_din),      // Debug register data input
    .dbg_rst      (dbg_rst),      // Debug unit reset
    .decode_noirq (decode_noirq), // Frontend decode instruction
    .eu_mab       (eu_mab),       // Execution-Unit Memory address bus
    .eu_mb_en     (eu_mb_en),     // Execution-Unit Memory bus enable
    .eu_mb_wr     (eu_mb_wr),     // Execution-Unit Memory bus write transfer
    .pc           (pc)            // Program counter
);
 
`else
assign brk3_halt =  1'b0;
assign brk3_pnd  =  1'b0;
assign brk3_dout = 16'h0000;
`endif
 
 
//============================================================================
// 6) DATA OUTPUT GENERATION
//============================================================================
 
wire [15:0] cpu_id_lo_rd = cpu_id[15:0]           & {16{reg_rd[CPU_ID_LO]}};
wire [15:0] cpu_id_hi_rd = cpu_id[31:16]          & {16{reg_rd[CPU_ID_HI]}};
wire [15:0] cpu_ctl_rd   = {8'h00, cpu_ctl_full}  & {16{reg_rd[CPU_CTL]}};
wire [15:0] cpu_stat_rd  = {8'h00, cpu_stat_full} & {16{reg_rd[CPU_STAT]}};
wire [15:0] mem_ctl_rd   = {8'h00, mem_ctl_full}  & {16{reg_rd[MEM_CTL]}};
wire [15:0] mem_data_rd  = mem_data               & {16{reg_rd[MEM_DATA]}};
wire [15:0] mem_addr_rd  = mem_addr               & {16{reg_rd[MEM_ADDR]}};
wire [15:0] mem_cnt_rd   = mem_cnt                & {16{reg_rd[MEM_CNT]}};
wire [15:0] cpu_nr_rd    = cpu_nr                 & {16{reg_rd[CPU_NR]}};
 
wire [15:0] dbg_dout = cpu_id_lo_rd |
                       cpu_id_hi_rd |
                       cpu_ctl_rd   |
                       cpu_stat_rd  |
                       mem_ctl_rd   |
                       mem_data_rd  |
                       mem_addr_rd  |
                       mem_cnt_rd   |
                       brk0_dout    |
                       brk1_dout    |
                       brk2_dout    |
                       brk3_dout    |
                       cpu_nr_rd;
 
// Tell UART/I2C interface that the data is ready to be read
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)                       dbg_rd_rdy  <=  1'b0;
  else if (mem_burst | mem_burst_rd) dbg_rd_rdy  <= (dbg_reg_rd | dbg_mem_rd_dly);
  else                               dbg_rd_rdy  <=  dbg_rd;
 
 
//============================================================================
// 7) CPU CONTROL
//============================================================================
 
// Reset CPU
//--------------------------
wire dbg_cpu_reset  = cpu_ctl[`CPU_RST];
 
 
// Break after reset
//--------------------------
wire halt_rst = cpu_ctl[`RST_BRK_EN] & dbg_en_s & puc_pnd_set;
 
 
// Freeze peripherals
//--------------------------
wire dbg_freeze = dbg_halt_st & (cpu_ctl[`FRZ_BRK_EN] | ~cpu_en_s);
 
 
// Software break
//--------------------------
assign dbg_swbrk = (fe_mdb_in==`DBG_SWBRK_OP) & decode_noirq & cpu_ctl[`SW_BRK_EN];
 
 
// Single step
//--------------------------
reg [1:0] inc_step;
always @(posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)    inc_step <= 2'b00;
  else if (istep) inc_step <= 2'b11;
  else            inc_step <= {inc_step[0], 1'b0};
 
 
// Run / Halt
//--------------------------
reg   halt_flag;
 
wire  mem_halt_cpu;
wire  mem_run_cpu;
 
wire  halt_flag_clr = run_cpu   | mem_run_cpu;
wire  halt_flag_set = halt_cpu  | halt_rst  | dbg_swbrk | mem_halt_cpu |
                      brk0_halt | brk1_halt | brk2_halt | brk3_halt;
 
always @(posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)            halt_flag <= 1'b0;
  else if (halt_flag_clr) halt_flag <= 1'b0;
  else if (halt_flag_set) halt_flag <= 1'b1;
 
wire dbg_halt_cmd = (halt_flag | halt_flag_set) & ~inc_step[1];
 
 
//============================================================================
// 8) MEMORY CONTROL
//============================================================================
 
// Control Memory bursts
//------------------------------
 
wire mem_burst_start = (mem_start             &  |mem_cnt);
wire mem_burst_end   = ((dbg_wr | dbg_rd_rdy) & ~|mem_cnt);
 
// Detect when burst is on going
always @(posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)              mem_burst <= 1'b0;
  else if (mem_burst_start) mem_burst <= 1'b1;
  else if (mem_burst_end)   mem_burst <= 1'b0;
 
// Control signals for UART/I2C interface
assign mem_burst_rd = (mem_burst_start & ~mem_ctl[1]);
assign mem_burst_wr = (mem_burst_start &  mem_ctl[1]);
 
// Trigger CPU Register or memory access during a burst
reg        mem_startb;
always @(posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst) mem_startb <= 1'b0;
  else         mem_startb <= (mem_burst & (dbg_wr | dbg_rd)) | mem_burst_rd;
 
// Combine single and burst memory start of sequence
wire       mem_seq_start = ((mem_start & ~|mem_cnt) | mem_startb);
 
 
// Memory access state machine
//------------------------------
reg  [1:0] mem_state;
reg  [1:0] mem_state_nxt;
 
// State machine definition
parameter  M_IDLE       = 2'h0;
parameter  M_SET_BRK    = 2'h1;
parameter  M_ACCESS_BRK = 2'h2;
parameter  M_ACCESS     = 2'h3;
 
// State transition
always @(mem_state or mem_seq_start or dbg_halt_st)
  case (mem_state)
    M_IDLE       : mem_state_nxt = ~mem_seq_start ? M_IDLE       :
                                    dbg_halt_st   ? M_ACCESS     : M_SET_BRK;
    M_SET_BRK    : mem_state_nxt =  dbg_halt_st   ? M_ACCESS_BRK : M_SET_BRK;
    M_ACCESS_BRK : mem_state_nxt =  M_IDLE;
    M_ACCESS     : mem_state_nxt =  M_IDLE;
  // pragma coverage off
    default      : mem_state_nxt =  M_IDLE;
  // pragma coverage on
  endcase
 
// State machine
always @(posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst) mem_state <= M_IDLE;
  else         mem_state <= mem_state_nxt;
 
// Utility signals
assign mem_halt_cpu = (mem_state==M_IDLE)       & (mem_state_nxt==M_SET_BRK);
assign mem_run_cpu  = (mem_state==M_ACCESS_BRK) & (mem_state_nxt==M_IDLE);
assign mem_access   = (mem_state==M_ACCESS)     | (mem_state==M_ACCESS_BRK);
 
 
// Interface to CPU Registers and Memory bacbkone
//------------------------------------------------
assign      dbg_mem_addr   =  mem_addr;
assign      dbg_mem_dout   = ~mem_bw      ? mem_data               :
                              mem_addr[0] ? {mem_data[7:0], 8'h00} :
                                            {8'h00, mem_data[7:0]};
 
assign      dbg_reg_wr     = mem_access &  mem_ctl[1] &  mem_ctl[2];
assign      dbg_reg_rd     = mem_access & ~mem_ctl[1] &  mem_ctl[2];
 
assign      dbg_mem_en     = mem_access & ~mem_ctl[2];
assign      dbg_mem_rd     = dbg_mem_en & ~mem_ctl[1];
 
wire  [1:0] dbg_mem_wr_msk = ~mem_bw      ? 2'b11 :
                              mem_addr[0] ? 2'b10 : 2'b01;
assign      dbg_mem_wr     = {2{dbg_mem_en & mem_ctl[1]}} & dbg_mem_wr_msk;
 
 
// It takes one additional cycle to read from Memory as from registers
always @(posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst) dbg_mem_rd_dly <= 1'b0;
  else         dbg_mem_rd_dly <= dbg_mem_rd;
 
 
//=============================================================================
// 9)  UART COMMUNICATION
//=============================================================================
`ifdef DBG_UART
omsp_dbg_uart dbg_uart_0 (
 
// OUTPUTs
    .dbg_addr         (dbg_addr),         // Debug register address
    .dbg_din          (dbg_din),          // Debug register data input
    .dbg_rd           (dbg_rd),           // Debug register data read
    .dbg_uart_txd     (dbg_uart_txd),     // Debug interface: UART TXD
    .dbg_wr           (dbg_wr),           // Debug register data write
 
// INPUTs
    .dbg_clk          (dbg_clk),          // Debug unit clock
    .dbg_dout         (dbg_dout),         // Debug register data output
    .dbg_rd_rdy       (dbg_rd_rdy),       // Debug register data is ready for read
    .dbg_rst          (dbg_rst),          // Debug unit reset
    .dbg_uart_rxd     (dbg_uart_rxd),     // Debug interface: UART RXD
    .mem_burst        (mem_burst),        // Burst on going
    .mem_burst_end    (mem_burst_end),    // End TX/RX burst
    .mem_burst_rd     (mem_burst_rd),     // Start TX burst
    .mem_burst_wr     (mem_burst_wr),     // Start RX burst
    .mem_bw           (mem_bw)            // Burst byte width
);
 
`else
    assign dbg_uart_txd        =  1'b1;
 
    wire   UNUSED_dbg_uart_rxd =  dbg_uart_rxd;
 
 
  `ifdef DBG_I2C
  `else
    assign dbg_addr            =  6'h00;
    assign dbg_din             = 16'h0000;
    assign dbg_rd              =  1'b0;
    assign dbg_wr              =  1'b0;
  `endif
`endif
 
//=============================================================================
// 10)  I2C COMMUNICATION
//=============================================================================
`ifdef DBG_I2C
omsp_dbg_i2c dbg_i2c_0 (
 
// OUTPUTs
    .dbg_addr          (dbg_addr),          // Debug register address
    .dbg_din           (dbg_din),           // Debug register data input
    .dbg_i2c_sda_out   (dbg_i2c_sda_out),   // Debug interface: I2C SDA OUT
    .dbg_rd            (dbg_rd),            // Debug register data read
    .dbg_wr            (dbg_wr),            // Debug register data write
 
// INPUTs
    .dbg_clk           (dbg_clk),           // Debug unit clock
    .dbg_dout          (dbg_dout),          // Debug register data output
    .dbg_i2c_addr      (dbg_i2c_addr),      // Debug interface: I2C Address
    .dbg_i2c_broadcast (dbg_i2c_broadcast), // Debug interface: I2C Broadcast Address (for multicore systems)
    .dbg_i2c_scl       (dbg_i2c_scl),       // Debug interface: I2C SCL
    .dbg_i2c_sda_in    (dbg_i2c_sda_in),    // Debug interface: I2C SDA IN
    .dbg_rst           (dbg_rst),           // Debug unit reset
    .mem_burst         (mem_burst),         // Burst on going
    .mem_burst_end     (mem_burst_end),     // End TX/RX burst
    .mem_burst_rd      (mem_burst_rd),      // Start TX burst
    .mem_burst_wr      (mem_burst_wr),      // Start RX burst
    .mem_bw            (mem_bw)             // Burst byte width
);
 
`else
    assign     dbg_i2c_sda_out          = 1'b1;
 
    wire [6:0] UNUSED_dbg_i2c_addr      = dbg_i2c_addr;
    wire [6:0] UNUSED_dbg_i2c_broadcast = dbg_i2c_broadcast;
    wire       UNUSED_dbg_i2c_scl       = dbg_i2c_scl;
    wire       UNUSED_dbg_i2c_sda_in    = dbg_i2c_sda_in;
    wire       UNUSED_dbg_rd_rdy        = dbg_rd_rdy;
`endif
 
endmodule // omsp_dbg
 
`ifdef OMSP_NO_INCLUDE
`else
`include "openMSP430_undefines.v"
`endif