OpenCores
URL https://opencores.org/ocsvn/openmsp430/openmsp430/trunk

Subversion Repositories openmsp430

[/] [openmsp430/] [trunk/] [core/] [synthesis/] [xilinx/] [src/] [coregen/] [spartan3a_pmem.xco] - Rev 62

Compare with Previous | Blame | View Log

##############################################################
#
# Xilinx Core Generator version 11.4
# Date: Sat Jan 30 20:56:33 2010
#
##############################################################
#
#  This file contains the customisation parameters for a
#  Xilinx CORE Generator IP GUI. It is strongly recommended
#  that you do not manually alter this file as it may cause
#  unexpected and unsupported behavior.
#
##############################################################
#
# BEGIN Project Options
SET addpads = False
SET asysymbol = False
SET busformat = BusFormatAngleBracketNotRipped
SET createndf = False
SET designentry = Verilog
SET device = xc3s700a
SET devicefamily = spartan3a
SET flowvendor = Foundation_ISE
SET formalverification = False
SET foundationsym = False
SET implementationfiletype = Ngc
SET package = ft256
SET removerpms = False
SET simulationfiles = Behavioral
SET speedgrade = -4
SET verilogsim = True
SET vhdlsim = False
# END Project Options
# BEGIN Select
SELECT Block_Memory_Generator family Xilinx,_Inc. 3.3
# END Select
# BEGIN Parameters
CSET additional_inputs_for_power_estimation=false
CSET algorithm=Minimum_Area
CSET assume_synchronous_clk=false
CSET byte_size=8
CSET coe_file=no_coe_file_loaded
CSET collision_warnings=ALL
CSET component_name=spartan3a_pmem
CSET disable_collision_warnings=false
CSET disable_out_of_range_warnings=false
CSET ecc=false
CSET enable_a=Use_ENA_Pin
CSET enable_b=Always_Enabled
CSET error_injection_type=Single_Bit_Error_Injection
CSET fill_remaining_memory_locations=false
CSET load_init_file=false
CSET memory_type=Single_Port_RAM
CSET operating_mode_a=WRITE_FIRST
CSET operating_mode_b=WRITE_FIRST
CSET output_reset_value_a=0
CSET output_reset_value_b=0
CSET pipeline_stages=0
CSET port_a_clock=100
CSET port_a_enable_rate=100
CSET port_a_write_rate=50
CSET port_b_clock=100
CSET port_b_enable_rate=100
CSET port_b_write_rate=50
CSET primitive=8kx2
CSET read_width_a=16
CSET read_width_b=16
CSET register_porta_output_of_memory_core=false
CSET register_porta_output_of_memory_primitives=false
CSET register_portb_output_of_memory_core=false
CSET register_portb_output_of_memory_primitives=false
CSET remaining_memory_locations=0
CSET reset_memory_latch_a=false
CSET reset_memory_latch_b=false
CSET reset_priority_a=CE
CSET reset_priority_b=CE
CSET reset_type=SYNC
CSET use_byte_write_enable=true
CSET use_error_injection_pins=false
CSET use_regcea_pin=false
CSET use_regceb_pin=false
CSET use_rsta_pin=false
CSET use_rstb_pin=false
CSET write_depth_a=4096
CSET write_width_a=16
CSET write_width_b=16
# END Parameters
GENERATE
# CRC: fb194190

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.