OpenCores
URL https://opencores.org/ocsvn/openmsp430/openmsp430/trunk

Subversion Repositories openmsp430

[/] [openmsp430/] [trunk/] [fpga/] [actel_m1a3pl_dev_kit/] [rtl/] [verilog/] [openmsp430/] [periph/] [omsp_gpio.v] - Rev 218

Go to most recent revision | Compare with Previous | Blame | View Log

//----------------------------------------------------------------------------
// Copyright (C) 2009 , Olivier Girard
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//     * Redistributions of source code must retain the above copyright
//       notice, this list of conditions and the following disclaimer.
//     * Redistributions in binary form must reproduce the above copyright
//       notice, this list of conditions and the following disclaimer in the
//       documentation and/or other materials provided with the distribution.
//     * Neither the name of the authors nor the names of its contributors
//       may be used to endorse or promote products derived from this software
//       without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
// OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
// THE POSSIBILITY OF SUCH DAMAGE
//
//----------------------------------------------------------------------------
//
// *File Name: omsp_gpio.v
// 
// *Module Description:
//                       Digital I/O interface
//
// *Author(s):
//              - Olivier Girard,    olgirard@gmail.com
//
//----------------------------------------------------------------------------
// $Rev: 103 $
// $LastChangedBy: olivier.girard $
// $LastChangedDate: 2011-03-05 15:44:48 +0100 (Sat, 05 Mar 2011) $
//----------------------------------------------------------------------------
 
module  omsp_gpio (
 
// OUTPUTs
    irq_port1,                      // Port 1 interrupt
    irq_port2,                      // Port 2 interrupt
    p1_dout,                        // Port 1 data output
    p1_dout_en,                     // Port 1 data output enable
    p1_sel,                         // Port 1 function select
    p2_dout,                        // Port 2 data output
    p2_dout_en,                     // Port 2 data output enable
    p2_sel,                         // Port 2 function select
    p3_dout,                        // Port 3 data output
    p3_dout_en,                     // Port 3 data output enable
    p3_sel,                         // Port 3 function select
    p4_dout,                        // Port 4 data output
    p4_dout_en,                     // Port 4 data output enable
    p4_sel,                         // Port 4 function select
    p5_dout,                        // Port 5 data output
    p5_dout_en,                     // Port 5 data output enable
    p5_sel,                         // Port 5 function select
    p6_dout,                        // Port 6 data output
    p6_dout_en,                     // Port 6 data output enable
    p6_sel,                         // Port 6 function select
    per_dout,                       // Peripheral data output
 
// INPUTs
    mclk,                           // Main system clock
    p1_din,                         // Port 1 data input
    p2_din,                         // Port 2 data input
    p3_din,                         // Port 3 data input
    p4_din,                         // Port 4 data input
    p5_din,                         // Port 5 data input
    p6_din,                         // Port 6 data input
    per_addr,                       // Peripheral address
    per_din,                        // Peripheral data input
    per_en,                         // Peripheral enable (high active)
    per_we,                         // Peripheral write enable (high active)
    puc_rst                         // Main system reset
);
 
// PARAMETERs
//============
parameter           P1_EN = 1'b1;   // Enable Port 1
parameter           P2_EN = 1'b1;   // Enable Port 2
parameter           P3_EN = 1'b0;   // Enable Port 3
parameter           P4_EN = 1'b0;   // Enable Port 4
parameter           P5_EN = 1'b0;   // Enable Port 5
parameter           P6_EN = 1'b0;   // Enable Port 6
 
 
// OUTPUTs
//=========
output              irq_port1;      // Port 1 interrupt
output              irq_port2;      // Port 2 interrupt
output        [7:0] p1_dout;        // Port 1 data output
output        [7:0] p1_dout_en;     // Port 1 data output enable
output        [7:0] p1_sel;         // Port 1 function select
output        [7:0] p2_dout;        // Port 2 data output
output        [7:0] p2_dout_en;     // Port 2 data output enable
output        [7:0] p2_sel;         // Port 2 function select
output        [7:0] p3_dout;        // Port 3 data output
output        [7:0] p3_dout_en;     // Port 3 data output enable
output        [7:0] p3_sel;         // Port 3 function select
output        [7:0] p4_dout;        // Port 4 data output
output        [7:0] p4_dout_en;     // Port 4 data output enable
output        [7:0] p4_sel;         // Port 4 function select
output        [7:0] p5_dout;        // Port 5 data output
output        [7:0] p5_dout_en;     // Port 5 data output enable
output        [7:0] p5_sel;         // Port 5 function select
output        [7:0] p6_dout;        // Port 6 data output
output        [7:0] p6_dout_en;     // Port 6 data output enable
output        [7:0] p6_sel;         // Port 6 function select
output       [15:0] per_dout;       // Peripheral data output
 
// INPUTs
//=========
input               mclk;           // Main system clock
input         [7:0] p1_din;         // Port 1 data input
input         [7:0] p2_din;         // Port 2 data input
input         [7:0] p3_din;         // Port 3 data input
input         [7:0] p4_din;         // Port 4 data input
input         [7:0] p5_din;         // Port 5 data input
input         [7:0] p6_din;         // Port 6 data input
input        [13:0] per_addr;       // Peripheral address
input        [15:0] per_din;        // Peripheral data input
input               per_en;         // Peripheral enable (high active)
input         [1:0] per_we;         // Peripheral write enable (high active)
input               puc_rst;        // Main system reset
 
 
//=============================================================================
// 1)  PARAMETER DECLARATION
//=============================================================================
 
// Masks
parameter              P1_EN_MSK   = {8{P1_EN[0]}};
parameter              P2_EN_MSK   = {8{P2_EN[0]}};
parameter              P3_EN_MSK   = {8{P3_EN[0]}};
parameter              P4_EN_MSK   = {8{P4_EN[0]}};
parameter              P5_EN_MSK   = {8{P5_EN[0]}};
parameter              P6_EN_MSK   = {8{P6_EN[0]}};
 
// Register base address (must be aligned to decoder bit width)
parameter       [14:0] BASE_ADDR   = 15'h0000;
 
// Decoder bit width (defines how many bits are considered for address decoding)
parameter              DEC_WD      =  6;
 
// Register addresses offset
parameter [DEC_WD-1:0] P1IN        = 'h20,                    // Port 1
                       P1OUT       = 'h21,
                       P1DIR       = 'h22,
                       P1IFG       = 'h23,
                       P1IES       = 'h24,
                       P1IE        = 'h25,
                       P1SEL       = 'h26,
                       P2IN        = 'h28,                    // Port 2
                       P2OUT       = 'h29,
                       P2DIR       = 'h2A,
                       P2IFG       = 'h2B,
                       P2IES       = 'h2C,
                       P2IE        = 'h2D,
                       P2SEL       = 'h2E,
                       P3IN        = 'h18,                    // Port 3
                       P3OUT       = 'h19,
                       P3DIR       = 'h1A,
                       P3SEL       = 'h1B,
                       P4IN        = 'h1C,                    // Port 4
                       P4OUT       = 'h1D,
                       P4DIR       = 'h1E,
                       P4SEL       = 'h1F,
                       P5IN        = 'h30,                    // Port 5
                       P5OUT       = 'h31,
                       P5DIR       = 'h32,
                       P5SEL       = 'h33,
                       P6IN        = 'h34,                    // Port 6
                       P6OUT       = 'h35,
                       P6DIR       = 'h36,
                       P6SEL       = 'h37;
 
// Register one-hot decoder utilities
parameter              DEC_SZ      =  (1 << DEC_WD);
parameter [DEC_SZ-1:0] BASE_REG    =  {{DEC_SZ-1{1'b0}}, 1'b1};
 
// Register one-hot decoder
parameter [DEC_SZ-1:0] P1IN_D      =  (BASE_REG << P1IN),     // Port 1
                       P1OUT_D     =  (BASE_REG << P1OUT),
                       P1DIR_D     =  (BASE_REG << P1DIR),
                       P1IFG_D     =  (BASE_REG << P1IFG),
                       P1IES_D     =  (BASE_REG << P1IES),
                       P1IE_D      =  (BASE_REG << P1IE),
                       P1SEL_D     =  (BASE_REG << P1SEL),
                       P2IN_D      =  (BASE_REG << P2IN),     // Port 2
                       P2OUT_D     =  (BASE_REG << P2OUT),
                       P2DIR_D     =  (BASE_REG << P2DIR),
                       P2IFG_D     =  (BASE_REG << P2IFG),
                       P2IES_D     =  (BASE_REG << P2IES),
                       P2IE_D      =  (BASE_REG << P2IE),
                       P2SEL_D     =  (BASE_REG << P2SEL),
                       P3IN_D      =  (BASE_REG << P3IN),     // Port 3
                       P3OUT_D     =  (BASE_REG << P3OUT),
                       P3DIR_D     =  (BASE_REG << P3DIR),
                       P3SEL_D     =  (BASE_REG << P3SEL),
                       P4IN_D      =  (BASE_REG << P4IN),     // Port 4
                       P4OUT_D     =  (BASE_REG << P4OUT),
                       P4DIR_D     =  (BASE_REG << P4DIR),
                       P4SEL_D     =  (BASE_REG << P4SEL),
                       P5IN_D      =  (BASE_REG << P5IN),     // Port 5
                       P5OUT_D     =  (BASE_REG << P5OUT),
                       P5DIR_D     =  (BASE_REG << P5DIR),
                       P5SEL_D     =  (BASE_REG << P5SEL),
                       P6IN_D      =  (BASE_REG << P6IN),     // Port 6
                       P6OUT_D     =  (BASE_REG << P6OUT),
                       P6DIR_D     =  (BASE_REG << P6DIR),
                       P6SEL_D     =  (BASE_REG << P6SEL); 
 
 
//============================================================================
// 2)  REGISTER DECODER
//============================================================================
 
// Local register selection
wire              reg_sel      =  per_en & (per_addr[13:DEC_WD-1]==BASE_ADDR[14:DEC_WD]);
 
// Register local address
wire [DEC_WD-1:0] reg_addr     =  {1'b0, per_addr[DEC_WD-2:0]};
 
// Register address decode
wire [DEC_SZ-1:0] reg_dec      =  (P1IN_D   &  {DEC_SZ{(reg_addr==(P1IN  >>1))  &  P1_EN[0]}})  |
                                  (P1OUT_D  &  {DEC_SZ{(reg_addr==(P1OUT >>1))  &  P1_EN[0]}})  |
                                  (P1DIR_D  &  {DEC_SZ{(reg_addr==(P1DIR >>1))  &  P1_EN[0]}})  |
                                  (P1IFG_D  &  {DEC_SZ{(reg_addr==(P1IFG >>1))  &  P1_EN[0]}})  |
                                  (P1IES_D  &  {DEC_SZ{(reg_addr==(P1IES >>1))  &  P1_EN[0]}})  |
                                  (P1IE_D   &  {DEC_SZ{(reg_addr==(P1IE  >>1))  &  P1_EN[0]}})  |
                                  (P1SEL_D  &  {DEC_SZ{(reg_addr==(P1SEL >>1))  &  P1_EN[0]}})  |
                                  (P2IN_D   &  {DEC_SZ{(reg_addr==(P2IN  >>1))  &  P2_EN[0]}})  |
                                  (P2OUT_D  &  {DEC_SZ{(reg_addr==(P2OUT >>1))  &  P2_EN[0]}})  |
                                  (P2DIR_D  &  {DEC_SZ{(reg_addr==(P2DIR >>1))  &  P2_EN[0]}})  |
                                  (P2IFG_D  &  {DEC_SZ{(reg_addr==(P2IFG >>1))  &  P2_EN[0]}})  |
                                  (P2IES_D  &  {DEC_SZ{(reg_addr==(P2IES >>1))  &  P2_EN[0]}})  |
                                  (P2IE_D   &  {DEC_SZ{(reg_addr==(P2IE  >>1))  &  P2_EN[0]}})  |
                                  (P2SEL_D  &  {DEC_SZ{(reg_addr==(P2SEL >>1))  &  P2_EN[0]}})  |
                                  (P3IN_D   &  {DEC_SZ{(reg_addr==(P3IN  >>1))  &  P3_EN[0]}})  |
                                  (P3OUT_D  &  {DEC_SZ{(reg_addr==(P3OUT >>1))  &  P3_EN[0]}})  |
                                  (P3DIR_D  &  {DEC_SZ{(reg_addr==(P3DIR >>1))  &  P3_EN[0]}})  |
                                  (P3SEL_D  &  {DEC_SZ{(reg_addr==(P3SEL >>1))  &  P3_EN[0]}})  |
                                  (P4IN_D   &  {DEC_SZ{(reg_addr==(P4IN  >>1))  &  P4_EN[0]}})  |
                                  (P4OUT_D  &  {DEC_SZ{(reg_addr==(P4OUT >>1))  &  P4_EN[0]}})  |
                                  (P4DIR_D  &  {DEC_SZ{(reg_addr==(P4DIR >>1))  &  P4_EN[0]}})  |
                                  (P4SEL_D  &  {DEC_SZ{(reg_addr==(P4SEL >>1))  &  P4_EN[0]}})  |
                                  (P5IN_D   &  {DEC_SZ{(reg_addr==(P5IN  >>1))  &  P5_EN[0]}})  |
                                  (P5OUT_D  &  {DEC_SZ{(reg_addr==(P5OUT >>1))  &  P5_EN[0]}})  |
                                  (P5DIR_D  &  {DEC_SZ{(reg_addr==(P5DIR >>1))  &  P5_EN[0]}})  |
                                  (P5SEL_D  &  {DEC_SZ{(reg_addr==(P5SEL >>1))  &  P5_EN[0]}})  |
                                  (P6IN_D   &  {DEC_SZ{(reg_addr==(P6IN  >>1))  &  P6_EN[0]}})  |
                                  (P6OUT_D  &  {DEC_SZ{(reg_addr==(P6OUT >>1))  &  P6_EN[0]}})  |
                                  (P6DIR_D  &  {DEC_SZ{(reg_addr==(P6DIR >>1))  &  P6_EN[0]}})  |
                                  (P6SEL_D  &  {DEC_SZ{(reg_addr==(P6SEL >>1))  &  P6_EN[0]}});
 
// Read/Write probes
wire              reg_lo_write =  per_we[0] & reg_sel;
wire              reg_hi_write =  per_we[1] & reg_sel;
wire              reg_read     = ~|per_we   & reg_sel;
 
// Read/Write vectors
wire [DEC_SZ-1:0] reg_hi_wr    = reg_dec & {DEC_SZ{reg_hi_write}};
wire [DEC_SZ-1:0] reg_lo_wr    = reg_dec & {DEC_SZ{reg_lo_write}};
wire [DEC_SZ-1:0] reg_rd       = reg_dec & {DEC_SZ{reg_read}}; 
 
//============================================================================
// 3) REGISTERS
//============================================================================
 
// P1IN Register
//---------------
wire [7:0] p1in;
 
omsp_sync_cell sync_cell_p1in_0 (.data_out(p1in[0]), .data_in(p1_din[0] & P1_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p1in_1 (.data_out(p1in[1]), .data_in(p1_din[1] & P1_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p1in_2 (.data_out(p1in[2]), .data_in(p1_din[2] & P1_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p1in_3 (.data_out(p1in[3]), .data_in(p1_din[3] & P1_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p1in_4 (.data_out(p1in[4]), .data_in(p1_din[4] & P1_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p1in_5 (.data_out(p1in[5]), .data_in(p1_din[5] & P1_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p1in_6 (.data_out(p1in[6]), .data_in(p1_din[6] & P1_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p1in_7 (.data_out(p1in[7]), .data_in(p1_din[7] & P1_EN[0]), .clk(mclk), .rst(puc_rst));
 
 
// P1OUT Register
//----------------
reg  [7:0] p1out;
 
wire       p1out_wr  = P1OUT[0] ? reg_hi_wr[P1OUT] : reg_lo_wr[P1OUT];
wire [7:0] p1out_nxt = P1OUT[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p1out <=  8'h00;
  else if (p1out_wr)  p1out <=  p1out_nxt & P1_EN_MSK;
 
assign p1_dout = p1out;
 
 
// P1DIR Register
//----------------
reg  [7:0] p1dir;
 
wire       p1dir_wr  = P1DIR[0] ? reg_hi_wr[P1DIR] : reg_lo_wr[P1DIR];
wire [7:0] p1dir_nxt = P1DIR[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p1dir <=  8'h00;
  else if (p1dir_wr)  p1dir <=  p1dir_nxt & P1_EN_MSK;
 
assign p1_dout_en = p1dir;
 
 
// P1IFG Register
//----------------
reg  [7:0] p1ifg;
 
wire       p1ifg_wr  = P1IFG[0] ? reg_hi_wr[P1IFG] : reg_lo_wr[P1IFG];
wire [7:0] p1ifg_nxt = P1IFG[0] ? per_din[15:8]    : per_din[7:0];
wire [7:0] p1ifg_set;
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p1ifg <=  8'h00;
  else if (p1ifg_wr)  p1ifg <=  (p1ifg_nxt | p1ifg_set) & P1_EN_MSK;
  else                p1ifg <=  (p1ifg     | p1ifg_set) & P1_EN_MSK;
 
// P1IES Register
//----------------
reg  [7:0] p1ies;
 
wire       p1ies_wr  = P1IES[0] ? reg_hi_wr[P1IES] : reg_lo_wr[P1IES];
wire [7:0] p1ies_nxt = P1IES[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p1ies <=  8'h00;
  else if (p1ies_wr)  p1ies <=  p1ies_nxt & P1_EN_MSK;
 
 
// P1IE Register
//----------------
reg  [7:0] p1ie;
 
wire       p1ie_wr  = P1IE[0] ? reg_hi_wr[P1IE] : reg_lo_wr[P1IE];
wire [7:0] p1ie_nxt = P1IE[0] ? per_din[15:8]   : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)       p1ie <=  8'h00;
  else if (p1ie_wr)  p1ie <=  p1ie_nxt & P1_EN_MSK;
 
 
// P1SEL Register
//----------------
reg  [7:0] p1sel;
 
wire       p1sel_wr  = P1SEL[0] ? reg_hi_wr[P1SEL] : reg_lo_wr[P1SEL];
wire [7:0] p1sel_nxt = P1SEL[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)       p1sel <=  8'h00;
  else if (p1sel_wr) p1sel <=  p1sel_nxt & P1_EN_MSK;
 
assign p1_sel = p1sel;
 
 
// P2IN Register
//---------------
wire [7:0] p2in;
 
omsp_sync_cell sync_cell_p2in_0 (.data_out(p2in[0]), .data_in(p2_din[0] & P2_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p2in_1 (.data_out(p2in[1]), .data_in(p2_din[1] & P2_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p2in_2 (.data_out(p2in[2]), .data_in(p2_din[2] & P2_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p2in_3 (.data_out(p2in[3]), .data_in(p2_din[3] & P2_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p2in_4 (.data_out(p2in[4]), .data_in(p2_din[4] & P2_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p2in_5 (.data_out(p2in[5]), .data_in(p2_din[5] & P2_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p2in_6 (.data_out(p2in[6]), .data_in(p2_din[6] & P2_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p2in_7 (.data_out(p2in[7]), .data_in(p2_din[7] & P2_EN[0]), .clk(mclk), .rst(puc_rst));
 
 
// P2OUT Register
//----------------
reg  [7:0] p2out;
 
wire       p2out_wr  = P2OUT[0] ? reg_hi_wr[P2OUT] : reg_lo_wr[P2OUT];
wire [7:0] p2out_nxt = P2OUT[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p2out <=  8'h00;
  else if (p2out_wr)  p2out <=  p2out_nxt & P2_EN_MSK;
 
assign p2_dout = p2out;
 
 
// P2DIR Register
//----------------
reg  [7:0] p2dir;
 
wire       p2dir_wr  = P2DIR[0] ? reg_hi_wr[P2DIR] : reg_lo_wr[P2DIR];
wire [7:0] p2dir_nxt = P2DIR[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p2dir <=  8'h00;
  else if (p2dir_wr)  p2dir <=  p2dir_nxt & P2_EN_MSK;
 
assign p2_dout_en = p2dir;
 
 
// P2IFG Register
//----------------
reg  [7:0] p2ifg;
 
wire       p2ifg_wr  = P2IFG[0] ? reg_hi_wr[P2IFG] : reg_lo_wr[P2IFG];
wire [7:0] p2ifg_nxt = P2IFG[0] ? per_din[15:8]    : per_din[7:0];
wire [7:0] p2ifg_set;
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p2ifg <=  8'h00;
  else if (p2ifg_wr)  p2ifg <=  (p2ifg_nxt | p2ifg_set) & P2_EN_MSK;
  else                p2ifg <=  (p2ifg     | p2ifg_set) & P2_EN_MSK;
 
 
// P2IES Register
//----------------
reg  [7:0] p2ies;
 
wire       p2ies_wr  = P2IES[0] ? reg_hi_wr[P2IES] : reg_lo_wr[P2IES];
wire [7:0] p2ies_nxt = P2IES[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p2ies <=  8'h00;
  else if (p2ies_wr)  p2ies <=  p2ies_nxt & P2_EN_MSK;
 
 
// P2IE Register
//----------------
reg  [7:0] p2ie;
 
wire       p2ie_wr  = P2IE[0] ? reg_hi_wr[P2IE] : reg_lo_wr[P2IE];
wire [7:0] p2ie_nxt = P2IE[0] ? per_din[15:8]   : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)       p2ie <=  8'h00;
  else if (p2ie_wr)  p2ie <=  p2ie_nxt & P2_EN_MSK;
 
 
// P2SEL Register
//----------------
reg  [7:0] p2sel;
 
wire       p2sel_wr  = P2SEL[0] ? reg_hi_wr[P2SEL] : reg_lo_wr[P2SEL];
wire [7:0] p2sel_nxt = P2SEL[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)       p2sel <=  8'h00;
  else if (p2sel_wr) p2sel <=  p2sel_nxt & P2_EN_MSK;
 
assign p2_sel = p2sel;
 
 
// P3IN Register
//---------------
wire  [7:0] p3in;
 
omsp_sync_cell sync_cell_p3in_0 (.data_out(p3in[0]), .data_in(p3_din[0] & P3_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p3in_1 (.data_out(p3in[1]), .data_in(p3_din[1] & P3_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p3in_2 (.data_out(p3in[2]), .data_in(p3_din[2] & P3_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p3in_3 (.data_out(p3in[3]), .data_in(p3_din[3] & P3_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p3in_4 (.data_out(p3in[4]), .data_in(p3_din[4] & P3_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p3in_5 (.data_out(p3in[5]), .data_in(p3_din[5] & P3_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p3in_6 (.data_out(p3in[6]), .data_in(p3_din[6] & P3_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p3in_7 (.data_out(p3in[7]), .data_in(p3_din[7] & P3_EN[0]), .clk(mclk), .rst(puc_rst));
 
 
// P3OUT Register
//----------------
reg  [7:0] p3out;
 
wire       p3out_wr  = P3OUT[0] ? reg_hi_wr[P3OUT] : reg_lo_wr[P3OUT];
wire [7:0] p3out_nxt = P3OUT[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p3out <=  8'h00;
  else if (p3out_wr)  p3out <=  p3out_nxt & P3_EN_MSK;
 
assign p3_dout = p3out;
 
 
// P3DIR Register
//----------------
reg  [7:0] p3dir;
 
wire       p3dir_wr  = P3DIR[0] ? reg_hi_wr[P3DIR] : reg_lo_wr[P3DIR];
wire [7:0] p3dir_nxt = P3DIR[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p3dir <=  8'h00;
  else if (p3dir_wr)  p3dir <=  p3dir_nxt & P3_EN_MSK;
 
assign p3_dout_en = p3dir;
 
 
// P3SEL Register
//----------------
reg  [7:0] p3sel;
 
wire       p3sel_wr  = P3SEL[0] ? reg_hi_wr[P3SEL] : reg_lo_wr[P3SEL];
wire [7:0] p3sel_nxt = P3SEL[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)       p3sel <=  8'h00;
  else if (p3sel_wr) p3sel <=  p3sel_nxt & P3_EN_MSK;
 
assign p3_sel = p3sel;
 
 
// P4IN Register
//---------------
wire  [7:0] p4in;
 
omsp_sync_cell sync_cell_p4in_0 (.data_out(p4in[0]), .data_in(p4_din[0] & P4_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p4in_1 (.data_out(p4in[1]), .data_in(p4_din[1] & P4_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p4in_2 (.data_out(p4in[2]), .data_in(p4_din[2] & P4_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p4in_3 (.data_out(p4in[3]), .data_in(p4_din[3] & P4_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p4in_4 (.data_out(p4in[4]), .data_in(p4_din[4] & P4_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p4in_5 (.data_out(p4in[5]), .data_in(p4_din[5] & P4_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p4in_6 (.data_out(p4in[6]), .data_in(p4_din[6] & P4_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p4in_7 (.data_out(p4in[7]), .data_in(p4_din[7] & P4_EN[0]), .clk(mclk), .rst(puc_rst));
 
 
// P4OUT Register
//----------------
reg  [7:0] p4out;
 
wire       p4out_wr  = P4OUT[0] ? reg_hi_wr[P4OUT] : reg_lo_wr[P4OUT];
wire [7:0] p4out_nxt = P4OUT[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p4out <=  8'h00;
  else if (p4out_wr)  p4out <=  p4out_nxt & P4_EN_MSK;
 
assign p4_dout = p4out;
 
 
// P4DIR Register
//----------------
reg  [7:0] p4dir;
 
wire       p4dir_wr  = P4DIR[0] ? reg_hi_wr[P4DIR] : reg_lo_wr[P4DIR];
wire [7:0] p4dir_nxt = P4DIR[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p4dir <=  8'h00;
  else if (p4dir_wr)  p4dir <=  p4dir_nxt & P4_EN_MSK;
 
assign p4_dout_en = p4dir;
 
 
// P4SEL Register
//----------------
reg  [7:0] p4sel;
 
wire       p4sel_wr  = P4SEL[0] ? reg_hi_wr[P4SEL] : reg_lo_wr[P4SEL];
wire [7:0] p4sel_nxt = P4SEL[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)       p4sel <=  8'h00;
  else if (p4sel_wr) p4sel <=  p4sel_nxt & P4_EN_MSK;
 
assign p4_sel = p4sel;
 
 
// P5IN Register
//---------------
wire  [7:0] p5in;
 
omsp_sync_cell sync_cell_p5in_0 (.data_out(p5in[0]), .data_in(p5_din[0] & P5_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p5in_1 (.data_out(p5in[1]), .data_in(p5_din[1] & P5_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p5in_2 (.data_out(p5in[2]), .data_in(p5_din[2] & P5_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p5in_3 (.data_out(p5in[3]), .data_in(p5_din[3] & P5_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p5in_4 (.data_out(p5in[4]), .data_in(p5_din[4] & P5_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p5in_5 (.data_out(p5in[5]), .data_in(p5_din[5] & P5_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p5in_6 (.data_out(p5in[6]), .data_in(p5_din[6] & P5_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p5in_7 (.data_out(p5in[7]), .data_in(p5_din[7] & P5_EN[0]), .clk(mclk), .rst(puc_rst));
 
 
// P5OUT Register
//----------------
reg  [7:0] p5out;
 
wire       p5out_wr  = P5OUT[0] ? reg_hi_wr[P5OUT] : reg_lo_wr[P5OUT];
wire [7:0] p5out_nxt = P5OUT[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p5out <=  8'h00;
  else if (p5out_wr)  p5out <=  p5out_nxt & P5_EN_MSK;
 
assign p5_dout = p5out;
 
 
// P5DIR Register
//----------------
reg  [7:0] p5dir;
 
wire       p5dir_wr  = P5DIR[0] ? reg_hi_wr[P5DIR] : reg_lo_wr[P5DIR];
wire [7:0] p5dir_nxt = P5DIR[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p5dir <=  8'h00;
  else if (p5dir_wr)  p5dir <=  p5dir_nxt & P5_EN_MSK;
 
assign p5_dout_en = p5dir;
 
 
// P5SEL Register
//----------------
reg  [7:0] p5sel;
 
wire       p5sel_wr  = P5SEL[0] ? reg_hi_wr[P5SEL] : reg_lo_wr[P5SEL];
wire [7:0] p5sel_nxt = P5SEL[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)       p5sel <=  8'h00;
  else if (p5sel_wr) p5sel <=  p5sel_nxt & P5_EN_MSK;
 
assign p5_sel = p5sel;
 
 
// P6IN Register
//---------------
wire  [7:0] p6in;
 
omsp_sync_cell sync_cell_p6in_0 (.data_out(p6in[0]), .data_in(p6_din[0] & P6_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p6in_1 (.data_out(p6in[1]), .data_in(p6_din[1] & P6_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p6in_2 (.data_out(p6in[2]), .data_in(p6_din[2] & P6_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p6in_3 (.data_out(p6in[3]), .data_in(p6_din[3] & P6_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p6in_4 (.data_out(p6in[4]), .data_in(p6_din[4] & P6_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p6in_5 (.data_out(p6in[5]), .data_in(p6_din[5] & P6_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p6in_6 (.data_out(p6in[6]), .data_in(p6_din[6] & P6_EN[0]), .clk(mclk), .rst(puc_rst));
omsp_sync_cell sync_cell_p6in_7 (.data_out(p6in[7]), .data_in(p6_din[7] & P6_EN[0]), .clk(mclk), .rst(puc_rst));
 
 
// P6OUT Register
//----------------
reg  [7:0] p6out;
 
wire       p6out_wr  = P6OUT[0] ? reg_hi_wr[P6OUT] : reg_lo_wr[P6OUT];
wire [7:0] p6out_nxt = P6OUT[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p6out <=  8'h00;
  else if (p6out_wr)  p6out <=  p6out_nxt & P6_EN_MSK;
 
assign p6_dout = p6out;
 
 
// P6DIR Register
//----------------
reg  [7:0] p6dir;
 
wire       p6dir_wr  = P6DIR[0] ? reg_hi_wr[P6DIR] : reg_lo_wr[P6DIR];
wire [7:0] p6dir_nxt = P6DIR[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        p6dir <=  8'h00;
  else if (p6dir_wr)  p6dir <=  p6dir_nxt & P6_EN_MSK;
 
assign p6_dout_en = p6dir;
 
 
// P6SEL Register
//----------------
reg  [7:0] p6sel;
 
wire       p6sel_wr  = P6SEL[0] ? reg_hi_wr[P6SEL] : reg_lo_wr[P6SEL];
wire [7:0] p6sel_nxt = P6SEL[0] ? per_din[15:8]    : per_din[7:0];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)       p6sel <=  8'h00;
  else if (p6sel_wr) p6sel <=  p6sel_nxt & P6_EN_MSK;
 
assign p6_sel = p6sel;
 
 
 
//============================================================================
// 4) INTERRUPT GENERATION
//============================================================================
 
// Port 1 interrupt
//------------------
 
// Delay input
reg    [7:0] p1in_dly;
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)  p1in_dly <=  8'h00;
  else          p1in_dly <=  p1in & P1_EN_MSK;    
 
// Edge detection
wire   [7:0] p1in_re   =   p1in & ~p1in_dly;
wire   [7:0] p1in_fe   =  ~p1in &  p1in_dly;
 
// Set interrupt flag
assign       p1ifg_set = {p1ies[7] ? p1in_fe[7] : p1in_re[7],
                          p1ies[6] ? p1in_fe[6] : p1in_re[6],
                          p1ies[5] ? p1in_fe[5] : p1in_re[5],
                          p1ies[4] ? p1in_fe[4] : p1in_re[4],
                          p1ies[3] ? p1in_fe[3] : p1in_re[3],
                          p1ies[2] ? p1in_fe[2] : p1in_re[2],
                          p1ies[1] ? p1in_fe[1] : p1in_re[1],
                          p1ies[0] ? p1in_fe[0] : p1in_re[0]} & P1_EN_MSK;
 
// Generate CPU interrupt
assign       irq_port1 = |(p1ie & p1ifg) & P1_EN[0];
 
 
// Port 1 interrupt
//------------------
 
// Delay input
reg    [7:0] p2in_dly;
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)  p2in_dly <=  8'h00;
  else          p2in_dly <=  p2in & P2_EN_MSK;    
 
// Edge detection
wire   [7:0] p2in_re   =   p2in & ~p2in_dly;
wire   [7:0] p2in_fe   =  ~p2in &  p2in_dly;
 
// Set interrupt flag
assign       p2ifg_set = {p2ies[7] ? p2in_fe[7] : p2in_re[7],
                          p2ies[6] ? p2in_fe[6] : p2in_re[6],
                          p2ies[5] ? p2in_fe[5] : p2in_re[5],
                          p2ies[4] ? p2in_fe[4] : p2in_re[4],
                          p2ies[3] ? p2in_fe[3] : p2in_re[3],
                          p2ies[2] ? p2in_fe[2] : p2in_re[2],
                          p2ies[1] ? p2in_fe[1] : p2in_re[1],
                          p2ies[0] ? p2in_fe[0] : p2in_re[0]} & P2_EN_MSK;
 
// Generate CPU interrupt
assign      irq_port2 = |(p2ie & p2ifg) & P2_EN[0];
 
 
//============================================================================
// 5) DATA OUTPUT GENERATION
//============================================================================
 
// Data output mux
wire [15:0] p1in_rd   = {8'h00, (p1in  & {8{reg_rd[P1IN]}})}  << (8 & {4{P1IN[0]}});
wire [15:0] p1out_rd  = {8'h00, (p1out & {8{reg_rd[P1OUT]}})} << (8 & {4{P1OUT[0]}});
wire [15:0] p1dir_rd  = {8'h00, (p1dir & {8{reg_rd[P1DIR]}})} << (8 & {4{P1DIR[0]}});
wire [15:0] p1ifg_rd  = {8'h00, (p1ifg & {8{reg_rd[P1IFG]}})} << (8 & {4{P1IFG[0]}});
wire [15:0] p1ies_rd  = {8'h00, (p1ies & {8{reg_rd[P1IES]}})} << (8 & {4{P1IES[0]}});
wire [15:0] p1ie_rd   = {8'h00, (p1ie  & {8{reg_rd[P1IE]}})}  << (8 & {4{P1IE[0]}});
wire [15:0] p1sel_rd  = {8'h00, (p1sel & {8{reg_rd[P1SEL]}})} << (8 & {4{P1SEL[0]}});
wire [15:0] p2in_rd   = {8'h00, (p2in  & {8{reg_rd[P2IN]}})}  << (8 & {4{P2IN[0]}});
wire [15:0] p2out_rd  = {8'h00, (p2out & {8{reg_rd[P2OUT]}})} << (8 & {4{P2OUT[0]}});
wire [15:0] p2dir_rd  = {8'h00, (p2dir & {8{reg_rd[P2DIR]}})} << (8 & {4{P2DIR[0]}});
wire [15:0] p2ifg_rd  = {8'h00, (p2ifg & {8{reg_rd[P2IFG]}})} << (8 & {4{P2IFG[0]}});
wire [15:0] p2ies_rd  = {8'h00, (p2ies & {8{reg_rd[P2IES]}})} << (8 & {4{P2IES[0]}});
wire [15:0] p2ie_rd   = {8'h00, (p2ie  & {8{reg_rd[P2IE]}})}  << (8 & {4{P2IE[0]}});
wire [15:0] p2sel_rd  = {8'h00, (p2sel & {8{reg_rd[P2SEL]}})} << (8 & {4{P2SEL[0]}});
wire [15:0] p3in_rd   = {8'h00, (p3in  & {8{reg_rd[P3IN]}})}  << (8 & {4{P3IN[0]}});
wire [15:0] p3out_rd  = {8'h00, (p3out & {8{reg_rd[P3OUT]}})} << (8 & {4{P3OUT[0]}});
wire [15:0] p3dir_rd  = {8'h00, (p3dir & {8{reg_rd[P3DIR]}})} << (8 & {4{P3DIR[0]}});
wire [15:0] p3sel_rd  = {8'h00, (p3sel & {8{reg_rd[P3SEL]}})} << (8 & {4{P3SEL[0]}});
wire [15:0] p4in_rd   = {8'h00, (p4in  & {8{reg_rd[P4IN]}})}  << (8 & {4{P4IN[0]}});
wire [15:0] p4out_rd  = {8'h00, (p4out & {8{reg_rd[P4OUT]}})} << (8 & {4{P4OUT[0]}});
wire [15:0] p4dir_rd  = {8'h00, (p4dir & {8{reg_rd[P4DIR]}})} << (8 & {4{P4DIR[0]}});
wire [15:0] p4sel_rd  = {8'h00, (p4sel & {8{reg_rd[P4SEL]}})} << (8 & {4{P4SEL[0]}});
wire [15:0] p5in_rd   = {8'h00, (p5in  & {8{reg_rd[P5IN]}})}  << (8 & {4{P5IN[0]}});
wire [15:0] p5out_rd  = {8'h00, (p5out & {8{reg_rd[P5OUT]}})} << (8 & {4{P5OUT[0]}});
wire [15:0] p5dir_rd  = {8'h00, (p5dir & {8{reg_rd[P5DIR]}})} << (8 & {4{P5DIR[0]}});
wire [15:0] p5sel_rd  = {8'h00, (p5sel & {8{reg_rd[P5SEL]}})} << (8 & {4{P5SEL[0]}});
wire [15:0] p6in_rd   = {8'h00, (p6in  & {8{reg_rd[P6IN]}})}  << (8 & {4{P6IN[0]}});
wire [15:0] p6out_rd  = {8'h00, (p6out & {8{reg_rd[P6OUT]}})} << (8 & {4{P6OUT[0]}});
wire [15:0] p6dir_rd  = {8'h00, (p6dir & {8{reg_rd[P6DIR]}})} << (8 & {4{P6DIR[0]}});
wire [15:0] p6sel_rd  = {8'h00, (p6sel & {8{reg_rd[P6SEL]}})} << (8 & {4{P6SEL[0]}});
 
wire [15:0] per_dout  =  p1in_rd   |
                         p1out_rd  |
                         p1dir_rd  |
                         p1ifg_rd  |
                         p1ies_rd  |
                         p1ie_rd   |
                         p1sel_rd  |
                         p2in_rd   |
                         p2out_rd  |
                         p2dir_rd  |
                         p2ifg_rd  |
                         p2ies_rd  |
                         p2ie_rd   |
                         p2sel_rd  |
                         p3in_rd   |
                         p3out_rd  |
                         p3dir_rd  |
                         p3sel_rd  |
                         p4in_rd   |
                         p4out_rd  |
                         p4dir_rd  |
                         p4sel_rd  |
                         p5in_rd   |
                         p5out_rd  |
                         p5dir_rd  |
                         p5sel_rd  |
                         p6in_rd   |
                         p6out_rd  |
                         p6dir_rd  |
                         p6sel_rd;
 
endmodule // omsp_gpio
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.