OpenCores
URL https://opencores.org/ocsvn/openmsp430/openmsp430/trunk

Subversion Repositories openmsp430

[/] [openmsp430/] [trunk/] [fpga/] [actel_m1a3pl_dev_kit/] [rtl/] [verilog/] [openmsp430/] [periph/] [template_periph_16b.v] - Rev 218

Go to most recent revision | Compare with Previous | Blame | View Log

//----------------------------------------------------------------------------
// Copyright (C) 2009 , Olivier Girard
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//     * Redistributions of source code must retain the above copyright
//       notice, this list of conditions and the following disclaimer.
//     * Redistributions in binary form must reproduce the above copyright
//       notice, this list of conditions and the following disclaimer in the
//       documentation and/or other materials provided with the distribution.
//     * Neither the name of the authors nor the names of its contributors
//       may be used to endorse or promote products derived from this software
//       without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
// OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
// THE POSSIBILITY OF SUCH DAMAGE
//
//----------------------------------------------------------------------------
//
// *File Name: template_periph_16b.v
// 
// *Module Description:
//                       16 bit peripheral template.
//
// *Author(s):
//              - Olivier Girard,    olgirard@gmail.com
//
//----------------------------------------------------------------------------
// $Rev: 103 $
// $LastChangedBy: olivier.girard $
// $LastChangedDate: 2011-03-05 15:44:48 +0100 (Sat, 05 Mar 2011) $
//----------------------------------------------------------------------------
 
module  template_periph_16b (
 
// OUTPUTs
    per_dout,                       // Peripheral data output
 
// INPUTs
    mclk,                           // Main system clock
    per_addr,                       // Peripheral address
    per_din,                        // Peripheral data input
    per_en,                         // Peripheral enable (high active)
    per_we,                         // Peripheral write enable (high active)
    puc_rst                         // Main system reset
);
 
// OUTPUTs
//=========
output       [15:0] per_dout;       // Peripheral data output
 
// INPUTs
//=========
input               mclk;           // Main system clock
input        [13:0] per_addr;       // Peripheral address
input        [15:0] per_din;        // Peripheral data input
input               per_en;         // Peripheral enable (high active)
input         [1:0] per_we;         // Peripheral write enable (high active)
input               puc_rst;        // Main system reset
 
 
//=============================================================================
// 1)  PARAMETER DECLARATION
//=============================================================================
 
// Register base address (must be aligned to decoder bit width)
parameter       [14:0] BASE_ADDR   = 15'h0190;
 
// Decoder bit width (defines how many bits are considered for address decoding)
parameter              DEC_WD      =  3;
 
// Register addresses offset
parameter [DEC_WD-1:0] CNTRL1      = 'h0,
                       CNTRL2      = 'h2,
                       CNTRL3      = 'h4,
                       CNTRL4      = 'h6;
 
// Register one-hot decoder utilities
parameter              DEC_SZ      =  (1 << DEC_WD);
parameter [DEC_SZ-1:0] BASE_REG    =  {{DEC_SZ-1{1'b0}}, 1'b1};
 
// Register one-hot decoder
parameter [DEC_SZ-1:0] CNTRL1_D    = (BASE_REG << CNTRL1),
                       CNTRL2_D    = (BASE_REG << CNTRL2),
                       CNTRL3_D    = (BASE_REG << CNTRL3),
                       CNTRL4_D    = (BASE_REG << CNTRL4);
 
 
//============================================================================
// 2)  REGISTER DECODER
//============================================================================
 
// Local register selection
wire              reg_sel   =  per_en & (per_addr[13:DEC_WD-1]==BASE_ADDR[14:DEC_WD]);
 
// Register local address
wire [DEC_WD-1:0] reg_addr  =  {per_addr[DEC_WD-2:0], 1'b0};
 
// Register address decode
wire [DEC_SZ-1:0] reg_dec   =  (CNTRL1_D  &  {DEC_SZ{(reg_addr == CNTRL1 )}})  |
                               (CNTRL2_D  &  {DEC_SZ{(reg_addr == CNTRL2 )}})  |
                               (CNTRL3_D  &  {DEC_SZ{(reg_addr == CNTRL3 )}})  |
                               (CNTRL4_D  &  {DEC_SZ{(reg_addr == CNTRL4 )}});
 
// Read/Write probes
wire              reg_write =  |per_we & reg_sel;
wire              reg_read  = ~|per_we & reg_sel;
 
// Read/Write vectors
wire [DEC_SZ-1:0] reg_wr    = reg_dec & {DEC_SZ{reg_write}};
wire [DEC_SZ-1:0] reg_rd    = reg_dec & {DEC_SZ{reg_read}};
 
 
//============================================================================
// 3) REGISTERS
//============================================================================
 
// CNTRL1 Register
//-----------------   
reg  [15:0] cntrl1;
 
wire        cntrl1_wr = reg_wr[CNTRL1];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        cntrl1 <=  16'h0000;
  else if (cntrl1_wr) cntrl1 <=  per_din;
 
 
// CNTRL2 Register
//-----------------   
reg  [15:0] cntrl2;
 
wire        cntrl2_wr = reg_wr[CNTRL2];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        cntrl2 <=  16'h0000;
  else if (cntrl2_wr) cntrl2 <=  per_din;
 
 
// CNTRL3 Register
//-----------------   
reg  [15:0] cntrl3;
 
wire        cntrl3_wr = reg_wr[CNTRL3];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        cntrl3 <=  16'h0000;
  else if (cntrl3_wr) cntrl3 <=  per_din;
 
 
// CNTRL4 Register
//-----------------   
reg  [15:0] cntrl4;
 
wire        cntrl4_wr = reg_wr[CNTRL4];
 
always @ (posedge mclk or posedge puc_rst)
  if (puc_rst)        cntrl4 <=  16'h0000;
  else if (cntrl4_wr) cntrl4 <=  per_din;
 
 
//============================================================================
// 4) DATA OUTPUT GENERATION
//============================================================================
 
// Data output mux
wire [15:0] cntrl1_rd  = cntrl1  & {16{reg_rd[CNTRL1]}};
wire [15:0] cntrl2_rd  = cntrl2  & {16{reg_rd[CNTRL2]}};
wire [15:0] cntrl3_rd  = cntrl3  & {16{reg_rd[CNTRL3]}};
wire [15:0] cntrl4_rd  = cntrl4  & {16{reg_rd[CNTRL4]}};
 
wire [15:0] per_dout   =  cntrl1_rd  |
                          cntrl2_rd  |
                          cntrl3_rd  |
                          cntrl4_rd;
 
 
endmodule // template_periph_16b
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.