OpenCores
URL https://opencores.org/ocsvn/openmsp430/openmsp430/trunk

Subversion Repositories openmsp430

[/] [openmsp430/] [trunk/] [fpga/] [altera_de0_nano_soc/] [rtl/] [verilog/] [openmsp430/] [omsp_dbg_hwbrk.v] - Rev 221

Compare with Previous | Blame | View Log

//----------------------------------------------------------------------------
// Copyright (C) 2009 , Olivier Girard
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//     * Redistributions of source code must retain the above copyright
//       notice, this list of conditions and the following disclaimer.
//     * Redistributions in binary form must reproduce the above copyright
//       notice, this list of conditions and the following disclaimer in the
//       documentation and/or other materials provided with the distribution.
//     * Neither the name of the authors nor the names of its contributors
//       may be used to endorse or promote products derived from this software
//       without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
// OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
// THE POSSIBILITY OF SUCH DAMAGE
//
//----------------------------------------------------------------------------
//
// *File Name: omsp_dbg_hwbrk.v
//
// *Module Description:
//                       Hardware Breakpoint / Watchpoint module
//
// *Author(s):
//              - Olivier Girard,    olgirard@gmail.com
//
//----------------------------------------------------------------------------
// $Rev$
// $LastChangedBy$
// $LastChangedDate$
//----------------------------------------------------------------------------
`ifdef OMSP_NO_INCLUDE
`else
`include "openMSP430_defines.v"
`endif
 
module  omsp_dbg_hwbrk (
 
// OUTPUTs
    brk_halt,                // Hardware breakpoint command
    brk_pnd,                 // Hardware break/watch-point pending
    brk_dout,                // Hardware break/watch-point register data input
 
// INPUTs
    brk_reg_rd,              // Hardware break/watch-point register read select
    brk_reg_wr,              // Hardware break/watch-point register write select
    dbg_clk,                 // Debug unit clock
    dbg_din,                 // Debug register data input
    dbg_rst,                 // Debug unit reset
    decode_noirq,            // Frontend decode instruction
    eu_mab,                  // Execution-Unit Memory address bus
    eu_mb_en,                // Execution-Unit Memory bus enable
    eu_mb_wr,                // Execution-Unit Memory bus write transfer
    pc                       // Program counter
);
 
// OUTPUTs
//=========
output         brk_halt;     // Hardware breakpoint command
output         brk_pnd;      // Hardware break/watch-point pending
output  [15:0] brk_dout;     // Hardware break/watch-point register data input
 
// INPUTs
//=========
input    [3:0] brk_reg_rd;   // Hardware break/watch-point register read select
input    [3:0] brk_reg_wr;   // Hardware break/watch-point register write select
input          dbg_clk;      // Debug unit clock
input   [15:0] dbg_din;      // Debug register data input
input          dbg_rst;      // Debug unit reset
input          decode_noirq; // Frontend decode instruction
input   [15:0] eu_mab;       // Execution-Unit Memory address bus
input          eu_mb_en;     // Execution-Unit Memory bus enable
input    [1:0] eu_mb_wr;     // Execution-Unit Memory bus write transfer
input   [15:0] pc;           // Program counter
 
 
//=============================================================================
// 1)  WIRE & PARAMETER DECLARATION
//=============================================================================
 
wire      range_wr_set;
wire      range_rd_set;
wire      addr1_wr_set;
wire      addr1_rd_set;
wire      addr0_wr_set;
wire      addr0_rd_set;
 
 
parameter BRK_CTL   = 0,
          BRK_STAT  = 1,
          BRK_ADDR0 = 2,
          BRK_ADDR1 = 3;
 
 
//=============================================================================
// 2)  CONFIGURATION REGISTERS
//=============================================================================
 
// BRK_CTL Register
//-----------------------------------------------------------------------------
//       7   6   5        4            3          2            1  0
//        Reserved    RANGE_MODE    INST_EN    BREAK_EN    ACCESS_MODE
//
// ACCESS_MODE: - 00 : Disabled
//              - 01 : Detect read access
//              - 10 : Detect write access
//              - 11 : Detect read/write access
//              NOTE: '10' & '11' modes are not supported on the instruction flow
//
// BREAK_EN:    -  0 : Watchmode enable
//              -  1 : Break enable
//
// INST_EN:     -  0 : Checks are done on the execution unit (data flow)
//              -  1 : Checks are done on the frontend (instruction flow)
//
// RANGE_MODE:  -  0 : Address match on BRK_ADDR0 or BRK_ADDR1
//              -  1 : Address match on BRK_ADDR0->BRK_ADDR1 range
//
//-----------------------------------------------------------------------------
reg   [4:0] brk_ctl;
 
wire        brk_ctl_wr = brk_reg_wr[BRK_CTL];
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)         brk_ctl <=  5'h00;
  else if (brk_ctl_wr) brk_ctl <=  {`HWBRK_RANGE & dbg_din[4], dbg_din[3:0]};
 
wire  [7:0] brk_ctl_full = {3'b000, brk_ctl};
 
 
// BRK_STAT Register
//-----------------------------------------------------------------------------
//     7    6       5         4         3         2         1         0
//    Reserved  RANGE_WR  RANGE_RD  ADDR1_WR  ADDR1_RD  ADDR0_WR  ADDR0_RD
//-----------------------------------------------------------------------------
reg   [5:0] brk_stat;
 
wire        brk_stat_wr  = brk_reg_wr[BRK_STAT];
wire  [5:0] brk_stat_set = {range_wr_set & `HWBRK_RANGE,
                            range_rd_set & `HWBRK_RANGE,
			    addr1_wr_set, addr1_rd_set,
			    addr0_wr_set, addr0_rd_set};
wire  [5:0] brk_stat_clr = ~dbg_din[5:0];
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)          brk_stat <=  6'h00;
  else if (brk_stat_wr) brk_stat <= ((brk_stat & brk_stat_clr) | brk_stat_set);
  else                  brk_stat <=  (brk_stat                 | brk_stat_set);
 
wire  [7:0] brk_stat_full = {2'b00, brk_stat};
wire        brk_pnd       = |brk_stat;
 
 
// BRK_ADDR0 Register
//-----------------------------------------------------------------------------
reg  [15:0] brk_addr0;
 
wire        brk_addr0_wr = brk_reg_wr[BRK_ADDR0];
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)           brk_addr0 <=  16'h0000;
  else if (brk_addr0_wr) brk_addr0 <=  dbg_din;
 
 
// BRK_ADDR1/DATA0 Register
//-----------------------------------------------------------------------------
reg  [15:0] brk_addr1;
 
wire        brk_addr1_wr = brk_reg_wr[BRK_ADDR1];
 
always @ (posedge dbg_clk or posedge dbg_rst)
  if (dbg_rst)           brk_addr1 <=  16'h0000;
  else if (brk_addr1_wr) brk_addr1 <=  dbg_din;
 
 
//============================================================================
// 3) DATA OUTPUT GENERATION
//============================================================================
 
wire [15:0] brk_ctl_rd   = {8'h00, brk_ctl_full}  & {16{brk_reg_rd[BRK_CTL]}};
wire [15:0] brk_stat_rd  = {8'h00, brk_stat_full} & {16{brk_reg_rd[BRK_STAT]}};
wire [15:0] brk_addr0_rd = brk_addr0              & {16{brk_reg_rd[BRK_ADDR0]}};
wire [15:0] brk_addr1_rd = brk_addr1              & {16{brk_reg_rd[BRK_ADDR1]}};
 
wire [15:0] brk_dout = brk_ctl_rd   |
                       brk_stat_rd  |
                       brk_addr0_rd |
                       brk_addr1_rd;
 
 
//============================================================================
// 4) BREAKPOINT / WATCHPOINT GENERATION
//============================================================================
 
// Comparators
//---------------------------
// Note: here the comparison logic is instanciated several times in order
//       to improve the timings, at the cost of a bit more area.
 
wire        equ_d_addr0 = eu_mb_en & (eu_mab==brk_addr0) & ~brk_ctl[`BRK_RANGE];
wire        equ_d_addr1 = eu_mb_en & (eu_mab==brk_addr1) & ~brk_ctl[`BRK_RANGE];
wire        equ_d_range = eu_mb_en & ((eu_mab>=brk_addr0) & (eu_mab<=brk_addr1)) &
                          brk_ctl[`BRK_RANGE] & `HWBRK_RANGE;
 
 
wire        equ_i_addr0 = decode_noirq & (pc==brk_addr0) & ~brk_ctl[`BRK_RANGE];
wire        equ_i_addr1 = decode_noirq & (pc==brk_addr1) & ~brk_ctl[`BRK_RANGE];
wire        equ_i_range = decode_noirq & ((pc>=brk_addr0) & (pc<=brk_addr1)) &
                          brk_ctl[`BRK_RANGE] & `HWBRK_RANGE;
 
 
// Detect accesses
//---------------------------
 
// Detect Instruction read access
wire i_addr0_rd =  equ_i_addr0 &  brk_ctl[`BRK_I_EN];
wire i_addr1_rd =  equ_i_addr1 &  brk_ctl[`BRK_I_EN];
wire i_range_rd =  equ_i_range &  brk_ctl[`BRK_I_EN];
 
// Detect Execution-Unit write access
wire d_addr0_wr =  equ_d_addr0 & ~brk_ctl[`BRK_I_EN] &  |eu_mb_wr;
wire d_addr1_wr =  equ_d_addr1 & ~brk_ctl[`BRK_I_EN] &  |eu_mb_wr;
wire d_range_wr =  equ_d_range & ~brk_ctl[`BRK_I_EN] &  |eu_mb_wr;
 
// Detect DATA read access
wire d_addr0_rd =  equ_d_addr0 & ~brk_ctl[`BRK_I_EN] & ~|eu_mb_wr;
wire d_addr1_rd =  equ_d_addr1 & ~brk_ctl[`BRK_I_EN] & ~|eu_mb_wr;
wire d_range_rd =  equ_d_range & ~brk_ctl[`BRK_I_EN] & ~|eu_mb_wr;
 
// Set flags
assign addr0_rd_set = brk_ctl[`BRK_MODE_RD] & (d_addr0_rd  | i_addr0_rd);
assign addr0_wr_set = brk_ctl[`BRK_MODE_WR] &  d_addr0_wr;
assign addr1_rd_set = brk_ctl[`BRK_MODE_RD] & (d_addr1_rd  | i_addr1_rd);
assign addr1_wr_set = brk_ctl[`BRK_MODE_WR] &  d_addr1_wr;
assign range_rd_set = brk_ctl[`BRK_MODE_RD] & (d_range_rd  | i_range_rd);
assign range_wr_set = brk_ctl[`BRK_MODE_WR] &  d_range_wr;
 
 
// Break CPU
assign brk_halt     = brk_ctl[`BRK_EN] & |brk_stat_set;
 
 
endmodule // omsp_dbg_hwbrk
 
`ifdef OMSP_NO_INCLUDE
`else
`include "openMSP430_undefines.v"
`endif
 

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.