URL
https://opencores.org/ocsvn/openmsp430/openmsp430/trunk
Subversion Repositories openmsp430
[/] [openmsp430/] [trunk/] [fpga/] [xilinx_avnet_lx9microbard/] [synthesis/] [xilinx/] [scripts/] [openMSP430_fpga.ucf] - Rev 171
Go to most recent revision | Compare with Previous | Blame | View Log
# ----------------------------------------------------------------------------# _____# / \# /____ \____# / \===\ \==/# /___\===\___\/ AVNET Design Resource Center# \======/ www.em.avnet.com/s6microboard# \====/# ----------------------------------------------------------------------------## Created With Avnet UCF Generator V0.3.0# Date: Friday, November 12, 2010# Time: 4:11:53 PM## Updates# 4 Jan 2011 -- added DIPs; changed IOSTANDARD for LEDs and LPDDR# 11 Jan 2011 -- Changed IOSTANDARD for DIPs to LVCMOS33.# Replaced '#' on the end of net names with '_n'# 14 Jan 2011 -- Added I2C for CDCE913 clock chip# Added formatting and section breaks# 27 Jan 2011 -- Updated URL for PMODs# 04 Aug 2011 -- Renaming USER_RESET_N to USER_RESET since it is not low-enabled;# Added extra comment on Ethernet PHY RXD pull-ups# Removed extraneous quote mark in I2C port syntax## This design is the property of Avnet. Publication of this# design is not authorized without written consent from Avnet.## Please direct any questions to:# Avnet Technical Forums# http://community.em.avnet.com/t5/Spartan-6-LX9-MicroBoard/bd-p/Spartan-6LX9MicroBoard## Avnet Centralized Technical Support# Centralized-Support@avnet.com# 1-800-422-9023## Disclaimer:# Avnet, Inc. makes no warranty for the use of this code or design.# This code is provided "As Is". Avnet, Inc assumes no responsibility for# any errors, which may appear in this code, nor does it make a commitment# to update the information contained herein. Avnet, Inc specifically# disclaims any implied warranties of fitness for a particular purpose.# Copyright(c) 2011 Avnet, Inc.# All rights reserved.## ----------------------------------------------------------------------------############################################################################# PROGRAM MEMORY PLACEMENT############################################################################# ROM Block AssignmentsINST "ram_16x8k_dp_pmem_shared/U0/xst_blk_mem_generator/gnativebmg.native_blk_mem_gen/valid.cstr/ramloop[4].ram.r/s6_noinit.ram/TRUE_DP.PRIM18.ram" LOC = "RAMB16_X0Y18";INST "ram_16x8k_dp_pmem_shared/U0/xst_blk_mem_generator/gnativebmg.native_blk_mem_gen/valid.cstr/ramloop[0].ram.r/s6_noinit.ram/TRUE_DP.PRIM18.ram" LOC = "RAMB16_X0Y10";INST "ram_16x8k_dp_pmem_shared/U0/xst_blk_mem_generator/gnativebmg.native_blk_mem_gen/valid.cstr/ramloop[5].ram.r/s6_noinit.ram/TRUE_DP.PRIM18.ram" LOC = "RAMB16_X0Y24";INST "ram_16x8k_dp_pmem_shared/U0/xst_blk_mem_generator/gnativebmg.native_blk_mem_gen/valid.cstr/ramloop[1].ram.r/s6_noinit.ram/TRUE_DP.PRIM18.ram" LOC = "RAMB16_X0Y16";INST "ram_16x8k_dp_pmem_shared/U0/xst_blk_mem_generator/gnativebmg.native_blk_mem_gen/valid.cstr/ramloop[6].ram.r/s6_noinit.ram/TRUE_DP.PRIM18.ram" LOC = "RAMB16_X0Y22";INST "ram_16x8k_dp_pmem_shared/U0/xst_blk_mem_generator/gnativebmg.native_blk_mem_gen/valid.cstr/ramloop[2].ram.r/s6_noinit.ram/TRUE_DP.PRIM18.ram" LOC = "RAMB16_X0Y14";INST "ram_16x8k_dp_pmem_shared/U0/xst_blk_mem_generator/gnativebmg.native_blk_mem_gen/valid.cstr/ramloop[7].ram.r/s6_noinit.ram/TRUE_DP.PRIM18.ram" LOC = "RAMB16_X0Y20";INST "ram_16x8k_dp_pmem_shared/U0/xst_blk_mem_generator/gnativebmg.native_blk_mem_gen/valid.cstr/ramloop[3].ram.r/s6_noinit.ram/TRUE_DP.PRIM18.ram" LOC = "RAMB16_X0Y12";############################################################################# VCC AUX VOLTAGE############################################################################CONFIG VCCAUX=3.3;############################################################################# User Reset Push Button# Ignore the timing for this signal# Internal pull-down required since external resistor is not populated############################################################################NET USER_RESET LOC = V4 | IOSTANDARD = LVCMOS33 | PULLDOWN; # "USER_RESET"NET USER_RESET TIG;############################################################################# Micron N25Q128 SPI Flash# This is a Multi-I/O Flash. Several pins have dual purposes# depending on the mode.############################################################################NET SPI_SCK LOC = R15 | IOSTANDARD = LVCMOS33; # "CCLK"NET SPI_CS_n LOC = V3 | IOSTANDARD = LVCMOS33; # "SPI_CS#"NET SPI_MOSI_MISO0 LOC = T13 | IOSTANDARD = LVCMOS33; # "MOSI_MISO0"NET SPI_MISO_MISO1 LOC = R13 | IOSTANDARD = LVCMOS33; # "D0_DIN_MISO_MISO1"NET SPI_Wn_MISO2 LOC = T14 | IOSTANDARD = LVCMOS33; # "D1_MISO2"NET SPI_HOLDn_MISO3 LOC = V14 | IOSTANDARD = LVCMOS33; # "D2_MISO3"############################################################################# Texas Instruments CDCE913 Triple-Output PLL Clock Chip# Y1: 40 MHz, USER_CLOCK can be used as external configuration clock# Y2: 66.667 MHz# Y3: 100 MHz############################################################################NET USER_CLOCK LOC = V10 | IOSTANDARD = LVCMOS33; # "USER_CLOCK"NET CLOCK_Y2 LOC = K15 | IOSTANDARD = LVCMOS33; # "CLOCK_Y2"NET CLOCK_Y3 LOC = C10 | IOSTANDARD = LVCMOS33; # "CLOCK_Y3"NET USER_CLOCK TNM_NET = USER_CLOCK;TIMESPEC TS_USER_CLOCK = PERIOD USER_CLOCK 40000 kHz;#NET CLOCK_Y2 TNM_NET = CLOCK_Y2;#TIMESPEC TS_CLOCK_Y2 = PERIOD CLOCK_Y2 66666.7 kHz;#NET CLOCK_Y3 TNM_NET = CLOCK_Y3;#TIMESPEC TS_CLOCK_Y3 = PERIOD CLOCK_Y3 100000 kHz;############################################################################# The following oscillator is not populated in production but the footprint# is compatible with the Maxim DS1088LU############################################################################NET BACKUP_CLK LOC = R8 | IOSTANDARD = LVCMOS33; # "MAIN_CLK"############################################################################# User DIP Switch x4# Internal pull-down required since external resistor is not populated############################################################################NET GPIO_DIP1 LOC = B3 | IOSTANDARD = LVCMOS33 | PULLDOWN; # "GPIO_DIP1"NET GPIO_DIP2 LOC = A3 | IOSTANDARD = LVCMOS33 | PULLDOWN; # "GPIO_DIP2"NET GPIO_DIP3 LOC = B4 | IOSTANDARD = LVCMOS33 | PULLDOWN; # "GPIO_DIP3"NET GPIO_DIP4 LOC = A4 | IOSTANDARD = LVCMOS33 | PULLDOWN; # "GPIO_DIP4"############################################################################# User LEDs############################################################################NET GPIO_LED1 LOC = P4 | IOSTANDARD = LVCMOS18; # "GPIO_LED1"NET GPIO_LED2 LOC = L6 | IOSTANDARD = LVCMOS18; # "GPIO_LED2"NET GPIO_LED3 LOC = F5 | IOSTANDARD = LVCMOS18; # "GPIO_LED3"NET GPIO_LED4 LOC = C2 | IOSTANDARD = LVCMOS18; # "GPIO_LED4"############################################################################# Silicon Labs CP2102 USB-to-UART Bridge Chip############################################################################NET USB_RS232_RXD LOC = R7 | IOSTANDARD = LVCMOS33; # "USB_RS232_RXD"NET USB_RS232_TXD LOC = T7 | IOSTANDARD = LVCMOS33; # "USB_RS232_TXD"############################################################################# Texas Instruments CDCE913 programming port# Internal pull-ups required since external resistors are not populated############################################################################NET SCL LOC=P12 | IOSTANDARD = LVCMOS33 | PULLUP; # "SCL"NET SDA LOC=U13 | IOSTANDARD = LVCMOS33 | PULLUP; # "SDA"############################################################################# Micron MT46H32M16LFBF-5 LPDDR############################################################################CONFIG MCB_PERFORMANCE= STANDARD;# AddressesNET LPDDR_A0 LOC = J7 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A0"NET LPDDR_A1 LOC = J6 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A1"NET LPDDR_A2 LOC = H5 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A2"NET LPDDR_A3 LOC = L7 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A3"NET LPDDR_A4 LOC = F3 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A4"NET LPDDR_A5 LOC = H4 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A5"NET LPDDR_A6 LOC = H3 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A6"NET LPDDR_A7 LOC = H6 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A7"NET LPDDR_A8 LOC = D2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A8"NET LPDDR_A9 LOC = D1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A9"NET LPDDR_A10 LOC = F4 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A10"NET LPDDR_A11 LOC = D3 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A11"NET LPDDR_A12 LOC = G6 | IOSTANDARD = MOBILE_DDR; # "LPDDR_A12"NET LPDDR_BA0 LOC = F2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_BA0"NET LPDDR_BA1 LOC = F1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_BA1"# DataNET LPDDR_DQ0 LOC = L2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ0"NET LPDDR_DQ1 LOC = L1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ1"NET LPDDR_DQ2 LOC = K2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ2"NET LPDDR_DQ3 LOC = K1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ3"NET LPDDR_DQ4 LOC = H2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ4"NET LPDDR_DQ5 LOC = H1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ5"NET LPDDR_DQ6 LOC = J3 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ6"NET LPDDR_DQ7 LOC = J1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ7"NET LPDDR_DQ8 LOC = M3 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ8"NET LPDDR_DQ9 LOC = M1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ9"NET LPDDR_DQ10 LOC = N2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ10"NET LPDDR_DQ11 LOC = N1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ11"NET LPDDR_DQ12 LOC = T2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ12"NET LPDDR_DQ13 LOC = T1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ13"NET LPDDR_DQ14 LOC = U2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ14"NET LPDDR_DQ15 LOC = U1 | IOSTANDARD = MOBILE_DDR; # "LPDDR_DQ15"NET LPDDR_LDM LOC = K3 | IOSTANDARD = MOBILE_DDR; # "LPDDR_LDM"NET LPDDR_UDM LOC = K4 | IOSTANDARD = MOBILE_DDR; # "LPDDR_UDM"NET LPDDR_LDQS LOC = L4 | IOSTANDARD = MOBILE_DDR; # "LPDDR_LDQS"NET LPDDR_UDQS LOC = P2 | IOSTANDARD = MOBILE_DDR; # "LPDDR_UDQS"# ClockNET LPDDR_CK_N LOC = G1 | IOSTANDARD = DIFF_MOBILE_DDR; # "LPDDR_CK_N"NET LPDDR_CK_P LOC = G3 | IOSTANDARD = DIFF_MOBILE_DDR; # "LPDDR_CK_P"NET LPDDR_CKE LOC = H7 | IOSTANDARD = MOBILE_DDR; # "LPDDR_CKE"# ControlNET LPDDR_CAS_n LOC = K5 | IOSTANDARD = MOBILE_DDR; # "LPDDR_CAS#"NET LPDDR_RAS_n LOC = L5 | IOSTANDARD = MOBILE_DDR; # "LPDDR_RAS#"NET LPDDR_WE_n LOC = E3 | IOSTANDARD = MOBILE_DDR; # "LPDDR_WE#"NET LPDDR_RZQ LOC = N4 | IOSTANDARD = MOBILE_DDR; # "LPDDR_RZQ"############################################################################# All the IO resources in an IO tile which contains DQSP/UDQSP are used# irrespective of a single-ended or differential DQS design. Any signal that# is connected to the free pin of the same IO tile in a single-ended design# will be unrouted. Hence, the IOB cannot used as general pupose IO.############################################################################CONFIG PROHIBIT = P1,L3;############################################################################# National Semiconductor DP83848J 10/100 Ethernet PHY# Pull-ups on RXD are necessary to set the PHY AD to 11110b.# Must keep the PHY from defaulting to PHY AD = 00000b# because this is Isolate Mode############################################################################NET ETH_COL LOC = M18 | IOSTANDARD = LVCMOS33 | PULLDOWN; # "ETH_COL"NET ETH_CRS LOC = N17 | IOSTANDARD = LVCMOS33 | PULLDOWN; # "ETH_CRS"NET ETH_MDC LOC = M16 | IOSTANDARD = LVCMOS33; # "ETH_MDC"NET ETH_MDIO LOC = L18 | IOSTANDARD = LVCMOS33; # "ETH_MDIO"NET ETH_RESET_n LOC = T18 | IOSTANDARD = LVCMOS33 | TIG; # "ETH_RESET#"NET ETH_RX_CLK LOC = L15 | IOSTANDARD = LVCMOS33; # "ETH_RX_CLK"NET ETH_RX_D0 LOC = T17 | IOSTANDARD = LVCMOS33 | PULLUP; # "ETH_RX_D0"NET ETH_RX_D1 LOC = N16 | IOSTANDARD = LVCMOS33 | PULLUP; # "ETH_RX_D1"NET ETH_RX_D2 LOC = N15 | IOSTANDARD = LVCMOS33 | PULLUP; # "ETH_RX_D2"NET ETH_RX_D3 LOC = P18 | IOSTANDARD = LVCMOS33 | PULLUP; # "ETH_RX_D3"NET ETH_RX_DV LOC = P17 | IOSTANDARD = LVCMOS33; # "ETH_RX_DV"NET ETH_RX_ER LOC = N18 | IOSTANDARD = LVCMOS33; # "ETH_RX_ER"NET ETH_TX_CLK LOC = H17 | IOSTANDARD = LVCMOS33; # "ETH_TX_CLK"NET ETH_TX_D0 LOC = K18 | IOSTANDARD = LVCMOS33; # "ETH_TX_D0"NET ETH_TX_D1 LOC = K17 | IOSTANDARD = LVCMOS33; # "ETH_TX_D1"NET ETH_TX_D2 LOC = J18 | IOSTANDARD = LVCMOS33; # "ETH_TX_D2"NET ETH_TX_D3 LOC = J16 | IOSTANDARD = LVCMOS33; # "ETH_TX_D3"NET ETH_TX_EN LOC = L17 | IOSTANDARD = LVCMOS33; # "ETH_TX_EN"############################################################################# Peripheral Modules and GPIO# Peripheral Modules (PMODs) were invented by Digilent Inc. as small,# inexpensive add-on boards for FPGA development boards. With costs# starting as low as $10, PMODs allow you to add a number of capabilities# to your board, including A/D, D/A, Wireless Radio, SD Card, 2x16# Character LCD and a variety of LEDs, switches, and headers. See the# complete library of Digilent PMODs at# https://www.digilentinc.com/PMODs############################################################################# Connector J5NET PMOD1_P1 LOC = F15 | IOSTANDARD = LVCMOS33; # "PMOD1_P1"NET PMOD1_P2 LOC = F16 | IOSTANDARD = LVCMOS33; # "PMOD1_P2"NET PMOD1_P3 LOC = C17 | IOSTANDARD = I2C | PULLUP; # "PMOD1_P3"NET PMOD1_P4 LOC = C18 | IOSTANDARD = I2C | PULLUP; # "PMOD1_P4"NET PMOD1_P7 LOC = F14 | IOSTANDARD = LVCMOS33; # "PMOD1_P7"NET PMOD1_P8 LOC = G14 | IOSTANDARD = LVCMOS33; # "PMOD1_P8"NET PMOD1_P9 LOC = D17 | IOSTANDARD = LVCMOS33; # "PMOD1_P9"NET PMOD1_P10 LOC = D18 | IOSTANDARD = LVCMOS33; # "PMOD1_P10"# Connector J4NET PMOD2_P1 LOC = H12 | IOSTANDARD = LVCMOS33; # "PMOD2_P1"NET PMOD2_P2 LOC = G13 | IOSTANDARD = LVCMOS33; # "PMOD2_P2"NET PMOD2_P3 LOC = E16 | IOSTANDARD = LVCMOS33; # "PMOD2_P3"NET PMOD2_P4 LOC = E18 | IOSTANDARD = LVCMOS33; # "PMOD2_P4"NET PMOD2_P7 LOC = K12 | IOSTANDARD = LVCMOS33; # "PMOD2_P7"NET PMOD2_P8 LOC = K13 | IOSTANDARD = LVCMOS33; # "PMOD2_P8"NET PMOD2_P9 LOC = F17 | IOSTANDARD = LVCMOS33; # "PMOD2_P9"NET PMOD2_P10 LOC = F18 | IOSTANDARD = LVCMOS33; # "PMOD2_P10"
Go to most recent revision | Compare with Previous | Blame | View Log