URL
https://opencores.org/ocsvn/openmsp430/openmsp430/trunk
Subversion Repositories openmsp430
[/] [openmsp430/] [trunk/] [fpga/] [xilinx_diligent_s3board/] [software/] [ta_uart/] [hardware.h] - Rev 104
Go to most recent revision | Compare with Previous | Blame | View Log
#ifndef HARDWARE_H #define HARDWARE_H #define __msp430_have_port3 #define __MSP430_HAS_PORT3__ #include <io.h> #include <signal.h> #include <iomacros.h> //PINS //PORT1 #define TX BIT1 //PORT2 #define RX BIT2 #define LED BIT1 //Port Output Register 'P1OUT, P2OUT': #define P1OUT_INIT TX //Init Output data of port1 #define P2OUT_INIT 0 //Init Output data of port2 #define P3OUT_INIT 0 //Init Output data of port3 //Port Direction Register 'P1DIR, P2DIR': #define P1DIR_INIT TX //Init of Port1 Data-Direction Reg (Out=1 / Inp=0) #define P2DIR_INIT ~RX //Init of Port2 Data-Direction Reg (Out=1 / Inp=0) #define P3DIR_INIT 0xff //Init of Port3 Data-Direction Reg (Out=1 / Inp=0) //Selection of Port or Module -Function on the Pins 'P1SEL, P2SEL' #define P1SEL_INIT 0 //P1-Modules: #define P2SEL_INIT RX //P2-Modules: #define P3SEL_INIT 0 //P3-Modules: //Interrupt capabilities of P1 and P2 #define P1IE_INIT 0 //Interrupt Enable (0=dis 1=enabled) #define P2IE_INIT 0 //Interrupt Enable (0=dis 1=enabled) #define P1IES_INIT 0 //Interrupt Edge Select (0=pos 1=neg) #define P2IES_INIT 0 //Interrupt Edge Select (0=pos 1=neg) #define IE_INIT 0 #define WDTCTL_INIT WDTPW|WDTHOLD #define BCSCTL1_FLL XT2OFF|DIVA1|RSEL2|RSEL0 #define BCSCTL2_FLL 0 #define TACTL_FLL TASSEL_2|TACLR #define CCTL2_FLL CM0|CCIS0|CAP #define TACTL_AFTER_FLL TASSEL_2|TACLR|ID_0 //#define BAUD 40 //9600 @3MHz div 8 //#define BAUD 20 //19200 @3MHz div 8 //#define BAUD 20 //9600 @1.5MHz div 8 //#define BAUD 140 //9600 @1.5MHz div 8 //#define BAUD 2083 //9600 @20.0MHz div 1 //#define BAUD 1042 //19200 @20.0MHz div 1 //#define BAUD 521 //38400 @20.0MHz div 1 //#define BAUD 347 //57600 @20.0MHz div 1 #define BAUD 174 //115200 @20.0MHz div 1 //#define BAUD 87 //230400 @20.0MHz div 1 //Selection of 'Digitally Controlled Oszillator' (desired frquency in HZ, 1..3 MHz) #define DCO_FREQ 1536000 //3072000/2 makes 9600 a bit more precise //Automatic, do not edit #define DCO_FSET (DCO_FREQ/8192) //DCO_FSET = DCO_FREQ / (32768/4) #define DCOCTL_MAX 0xff // Used from FLL to check when Rsel must be changed #define DCOCTL_MIN 0 // Used from FLL to check when Rsel must be changed #endif //HARDWARE_H
Go to most recent revision | Compare with Previous | Blame | View Log