URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [tags/] [gnu-src/] [newlib-1.18.0/] [newlib-1.18.0-or32-1.0rc1/] [libgloss/] [m32c/] [sample.c] - Rev 494
Go to most recent revision | Compare with Previous | Blame | View Log
/* Copyright (c) 2008 Red Hat Incorporated. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. The name of Red Hat Incorporated may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL RED HAT INCORPORATED BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ /* This is a sample program that shows how to use a few of the features of the M32C port of GCC, Binutils, and Newlib. */ #include <varvects.h> typedef unsigned char byte; typedef unsigned short word; #define prcr (*(volatile byte *)0x000a) #define cm0 (*(volatile byte *)0x0006) #define cm1 (*(volatile byte *)0x0007) #define ocd (*(volatile byte *)0x000c) #ifdef __r8c_cpu__ /* These are for the R8C/20 with LEDs on port P2 */ #define tracr (*(volatile byte *)0x0100) #define traioc (*(volatile byte *)0x0101) #define tramr (*(volatile byte *)0x0102) #define trapre (*(volatile byte *)0x0103) #define tra (*(volatile byte *)0x0104) #define traic (*(volatile byte *)0x0056) #define pd2 (*(volatile byte *)0x00e6) #define p2 (*(volatile byte *)0x00e4) #define ivec_timer_ra 22 #endif #ifdef __m32c_cpu__ /* These are for the M32C/83 with LEDs on port P0 and P1 */ #define ta0 (*(volatile word *)0x0346) #define ta0mr (*(volatile byte *)0x0356) #define tabsr (*(volatile byte *)0x0340) #define ta0ic (*(volatile byte *)0x006c) #define pd0 (*(volatile byte *)0x03e2) #define pd1 (*(volatile byte *)0x03e3) #define p0 (*(volatile byte *)0x03e0) #define p1 (*(volatile byte *)0x03e1) #define ivec_timer_a0 12 #endif /* Newlib's exit() pulls in lots of other things. Main() should never exit, but if it did, you could hard-reset the chip here. */ void exit(int rv) { while (1) asm volatile (""); } #ifdef __r8c_cpu__ /* The "constructor" attribute causes the startup code to call this sometime before main() is called. */ __attribute__((constructor)) void fast_clock(void) { asm("fclr I"); prcr = 1; cm0 = 0x08; cm1 = 0x38; asm("nop"); asm("nop"); asm("nop"); asm("nop"); ocd = 0; prcr = 0; asm("fset I"); } #endif /* We mark this volatile in case a non-interrupt function wants to read it, else gcc may optimize away extra reads. */ static volatile int tc = 1; /* The "interrupt" attribute changes the function entry/exit to properly preserve any changed registers. */ static void __attribute__((interrupt)) timer_ra_interrupt() { tc ++; #ifdef __r8c_cpu__ p2 = tc >> 4; #else p1 = tc; p0 = tc >> 8; #endif } main() { #ifdef __r8c_cpu__ pd2 = 0xff; /* TIMER RA */ tracr = 0x00; traioc = 0x00; tramr = 0x00; /* timer mode, f1 */ trapre = 255; /* prescaler */ tra = 255; /* cycle count */ _set_var_vect (timer_ra_interrupt, ivec_timer_ra); traic = 5; tracr = 1; #endif #ifdef __m32c_cpu__ pd0 = 0xff; pd1 = 0xff; /* TIMER A0 */ ta0mr = 0x00; /* Timer A0 mode register */ ta0 = 65535; /* Timer A0 register */ _set_var_vect (timer_ra_interrupt, ivec_timer_a0); ta0ic = 5; tabsr = 0xff; #endif /* main() must never return. */ while (1) ; }
Go to most recent revision | Compare with Previous | Blame | View Log