OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [bootloaders/] [orpmon/] [ChangeLog] - Rev 792

Go to most recent revision | Compare with Previous | Blame | View Log

2011-01-08  Julius Baxter  <julius@opencores.org>
        * include/flash.h: Whole filed surrounded with #ifdef FLASH_BASE_ADDR
        * include/spincursor: Deleted.
        * include/board.h: FLASH_ORG define for board 2 removed.
        <ETH_DATA_BASE>: Changed to reference _stack_top.
        <SANCHO_BASE_ADD>: Unused, so removed.
        * include/common.h: <_src_addr>: Extern define removed.
        <_stack_top>: Extern define added.
        * services/Makefile: Clean up commented-out things.
        * reset.S: Removed several unused .extern.
        <_mycrc32>: Removed.
        <_mysize>: Ditto.
        Removed SELF_CHECK section.
        Shifted .org for reset section to after .section definition (bugfix.)
        * cmds/global.c: 
        (globals_cmd): Shifted #if HELP_ENABLED to surround contents of
        function.
        * cmds/memory.c: Changed references from _src_addr to _stack_top.
        Remove all (were already commented out) spincursor references.
        * sim.cfg: Add Ethernet TAP configuration settings.
        * common/spincursos.c: Removed.
        * common/common.c: Change references from _src_addr to _stack_top.
        (main): Clean up.
        * flash.ld: <_stack_top>: Added.
        * ram.ld: <_src_addr>: Removed.
        <_stack_top>: Added.
        Removed reference to .crc section.
        * drivers/uart.c: Some formatting.
        
        
2011-01-07  Julius Baxter  <julius@opencores.org>
        * ChangeLog: Created
        * include/board.h: IP config 3 changes
        Remove flash defines for boards which do not have it.
        Reorganise UART and Ethernet modules defines
        <ETH_DATA_BASE>: Changed to point to just past top of stack.
        * reset.s: Remove flash boot options and early relocation boot code.
        Added BSS clearing code.
        * flash_reset.S: Added, containing all flash boot code.
        * config.mk: Added different optimization options (all commented out)
        * ram.ld: Add BSS symbols to help clearing.
        * include/eth.h: <ETH_TOTAL_BD>: Change to 8.
        <ETH_TXBD_NUM>: Change to 4.
        <ETH_RXBD_NUM>: Change to 4.
        <ETH_BUF_SPACE>: Added.
        * drivers/eth.c:
        (init_tx_bd_pool): Use updated version of ETH_DATA_BASE.
        (init_rx_bd_pool): Ditto.       
        * include/common.h: <_src_addr>: Added as extern (symbol from linker 
        script)
        * cmds/load.h: Added eth.h include.
        <COPYBOOT_LOCATION>: Defined in one place now, set as end of SDRAM
        minus the size of the relocate and boot program.
        A few flash functions surrounded with #ifdef FLASH_BASE_ADDR so they
        are compiled in only when the flash stuff is in use.
        (init_load): Whole CFG_IN_FLASH section removed. Tboot default location
        now set as end of ethernet buffer space.
        * cmds/memory.c:
        (testram): Warnings added if memory test will clobber stack. Start
        location automatically changed to end of stack, and test will abort
        if start location is before end location.
        

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.