OpenCores
URL https://opencores.org/ocsvn/openrisc_me/openrisc_me/trunk

Subversion Repositories openrisc_me

[/] [openrisc/] [trunk/] [gnu-src/] [gdb-7.2/] [gdb/] [testsuite/] [gdb.threads/] [threadapply.exp] - Rev 330

Compare with Previous | Blame | View Log

# This testcase is part of GDB, the GNU debugger.

# Copyright 2004, 2007, 2008, 2009, 2010 Free Software Foundation, Inc.

# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 3 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program.  If not, see <http://www.gnu.org/licenses/>.

if $tracelevel {
    strace $tracelevel
}


# This test verifies that a macro using backtrace can be applied to all threads
# and will continue for each thread even though an error may occur in
# backtracing one of the threads.

set testfile "threadapply"
set srcfile ${testfile}.c
set binfile ${objdir}/${subdir}/${testfile}
if {[gdb_compile_pthreads "${srcdir}/${subdir}/${srcfile}" "${binfile}" executable [list debug "incdir=${objdir}"]] != "" } {
    return -1
}

gdb_exit
gdb_start
gdb_reinitialize_dir $srcdir/$subdir
gdb_load ${binfile}

#
# Run to `main' where we begin our tests.
#

if ![runto_main] then {
    gdb_suppress_tests
}

# Break after all threads have been started.
set break_line [gdb_get_line_number "Break here"]
gdb_test "b $break_line" ".*"
gdb_test "continue"

gdb_test_multiple "define backthread" "defining macro" {
  -re "Type commands for definition of \"backthread\".\r\nEnd with a line saying just \"end\".\r\n>$" {
    gdb_test_multiple "bt\np/x 20\nend" "macro details" {
      -re "$gdb_prompt $" {
        pass "macro details"
      }
    }
    pass "defining macro"
  }
}

# Cause backtraces to fail by setting a limit.  This allows us to
# verify that the macro can get past the backtrace error and perform
# subsequent commands.
gdb_test_no_output "set backtrace limit 3"
gdb_test "thread apply all backthread" "Thread ..*\\\$\[0-9]+ = 0x14.*Thread ..*\\\$\[0-9]+ = 0x14.*Thread ..*\\\$\[0-9]+ = 0x14.*Thread ..*\\\$\[0-9]+ = 0x14.*Thread ..*\\\$\[0-9]+ = 0x14.*Thread ..*\\\$\[0-9]+ = 0x14"

# Go into the thread_function to check that a simple "thread apply"
# does not change the selected frame.
gdb_test "step" "thread_function.*" "step to the thread_function"
gdb_test "up" ".*in main.*" "go up in the stack frame" 
gdb_test "thread apply all print 1"  "Thread ..*\\\$\[0-9]+ = 1.*Thread ..*\\\$\[0-9]+ = 1.*Thread ..*\\\$\[0-9]+ = 1.*Thread ..*\\\$\[0-9]+ = 1.*Thread ..*\\\$\[0-9]+ = 1.*Thread ..*\\\$\[0-9]+ = 1" "run a simple print command on all threads"
gdb_test "down" "#0.*thread_function.*" "go down and check selected frame"

Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.