URL
https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc
[/] [openrisc/] [trunk/] [orpsocv2/] [boards/] [xilinx/] [atlys/] [rtl/] [verilog/] [xilinx_ddr2/] [mcb_raw_wrapper.v] - Rev 724
Go to most recent revision | Compare with Previous | Blame | View Log
//***************************************************************************** // (c) Copyright 2009 Xilinx, Inc. All rights reserved. // // This file contains confidential and proprietary information // of Xilinx, Inc. and is protected under U.S. and // international copyright and other intellectual property // laws. // // DISCLAIMER // This disclaimer is not a license and does not grant any // rights to the materials distributed herewith. Except as // otherwise provided in a valid license issued to you by // Xilinx, and to the maximum extent permitted by applicable // law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND // WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES // AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING // BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON- // INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and // (2) Xilinx shall not be liable (whether in contract or tort, // including negligence, or under any other theory of // liability) for any loss or damage of any kind or nature // related to, arising under or in connection with these // materials, including for any direct, or any indirect, // special, incidental, or consequential loss or damage // (including loss of data, profits, goodwill, or any type of // loss or damage suffered as a result of any action brought // by a third party) even if such damage or loss was // reasonably foreseeable or Xilinx had been advised of the // possibility of the same. // // CRITICAL APPLICATIONS // Xilinx products are not designed or intended to be fail- // safe, or for use in any application requiring fail-safe // performance, such as life-support or safety devices or // systems, Class III medical devices, nuclear facilities, // applications related to the deployment of airbags, or any // other applications that could lead to death, personal // injury, or severe property or environmental damage // (individually and collectively, "Critical // Applications"). Customer assumes the sole risk and // liability of any use of Xilinx products in Critical // Applications, subject only to applicable laws and // regulations governing limitations on product liability. // // THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS // PART OF THIS FILE AT ALL TIMES. // //***************************************************************************** // ____ ____ // / /\/ / // /___/ \ / Vendor: Xilinx // \ \ \/ Version: %version // \ \ Application: MIG // / / Filename: mcb_raw_wrapper.v // /___/ /\ Date Last Modified: $Date: 2010/10/27 17:40:12 $ // \ \ / \ Date Created: Thu June 24 2008 // \___\/\___\ // //Device: Spartan6 //Design Name: DDR/DDR2/DDR3/LPDDR //Purpose: //Reference: // This module is the intialization control logic of the memory interface. // All commands are issued from here acoording to the burst, CAS Latency and // the user commands. // // Revised History: // Rev 1.1 - added port_enable assignment for all configurations and rearrange // assignment siganls according to port number // - added timescale directive -SN 7-28-08 // - added C_ARB_NUM_TIME_SLOTS and removed the slot 12 through // 15 -SN 7-28-08 // - changed C_MEM_DDR2_WRT_RECOVERY = (C_MEM_TWR /C_MEMCLK_PERIOD) -SN 7-28-08 // - removed ghighb, gpwrdnb, gsr, gwe in port declaration. // For now tb need to force the signals inside the MCB and Wrapper // until a glbl.v is ready. Not sure how to do this in NCVerilog // flow. -SN 7-28-08 // // Rev 1.2 -- removed p*_cmd_error signals -SN 8-05-08 // Rev 1.3 -- Added gate logic for data port rd_en and wr_en in Config 3,4,5 - SN 8-8-08 // Rev 1.4 -- update changes that required by MCB core. - SN 9-11-09 // Rev 1.5 -- update. CMD delays has been removed in Sept 26 database. -- SN 9-28-08 // delay_cas_90,delay_ras_90,delay_cke_90,delay_odt_90,delay_rst_90 // delay_we_90 ,delay_address,delay_ba_90 = // --removed :assign #50 delay_dqnum = dqnum; // --removed :assign #50 delay_dqpum = dqpum; // --removed :assign #50 delay_dqnlm = dqnlm; // --removed :assign #50 delay_dqplm = dqplm; // --removed : delay_dqsIO_w_en_90_n // --removed : delay_dqsIO_w_en_90_p // --removed : delay_dqsIO_w_en_0 // -- corrected spelling error: C_MEM_RTRAS // Rev 1.6 -- update IODRP2 and OSERDES connection and was updated by Chip. 1-12-09 // -- rename the memc_wrapper.v to mcb_raw_wrapper.v // Rev 1.7 -- .READEN is removed in IODRP2_MCB 1-28-09 // -- connection has been updated // Rev 1.8 -- update memory parameter equations. 1-30_2009 // -- added portion of Soft IP // -- CAL_CLK_DIV is not used but MCB still has it // Rev 1.9 -- added Error checking for Invalid command to unidirectional port // Rev 1.10 -- changed the backend connection so that Simulation will work while // sw tools try to fix the model issues. 2-3-2009 // sysclk_2x_90 name is changed to sysclk_2x_180 . It created confusions. // It is acutally 180 degree difference. // Rev 1.11 -- Added soft_calibration_top. // Rev 1.12 -- fixed ui_clk connection to MCB when soft_calib_ip is on. 5-14-2009 // Rev 1.13 -- Added PULLUP/PULLDN for DQS/DQSN, UDQS/UDQSN lines. // Rev 1.14 -- Added minium condition for tRTP valud/ // REv 1.15 -- Bring the SKIP_IN_TERM_CAL and SKIP_DYNAMIC_CAL from calib_ip to top. 6-16-2009 // Rev 1.16 -- Fixed the WTR for DDR. 6-23-2009 // Rev 1.17 -- Fixed width mismatch for px_cmd_ra,px_cmd_ca,px_cmd_ba 7-02-2009 // Rev 1.18 -- Added lumpdelay parameters for 1.0 silicon support to bypass Calibration 7-10-2010 // Rev 1.19 -- Added soft fix to support refresh command. 7-15-2009. // Rev 1.20 -- Turned on the CALIB_SOFT_IP and C_MC_CALIBRATION_MODE is used to enable/disable // Dynamic DQS calibration in Soft Calibration module. // Rev 1.21 -- Added extra generate mcbx_dram_odt pin condition. It will not be generated if // RTT value is set to "disabled" // -- Corrected the UIUDQSDEC connection between soft_calib and MCB. // -- PLL_LOCK pin to MCB tie high. Soft Calib module asserts MCB_RST when pll_lock is deasserted. 1-19-2010 // Rev 1.22 -- Added DDR2 Initialization fix to meet 400 ns wait as outlined in step d) of JEDEC DDR2 spec . // Rev 1.23 -- Added DDR2 Initialization fix when C_CALIB_SOFT_IP set to "FALSE" //************************************************************************************************************************* `define DEBUG `timescale 1ps / 1ps module mcb_raw_wrapper # ( parameter C_MEMCLK_PERIOD = 2500, // /Mem clk period (in ps) parameter C_PORT_ENABLE = 6'b111111, // config1 : 6b'111111, config2: 4'b1111. config3 : 3'b111, config4: 2'b11, config5 1'b1 // C_PORT_ENABLE[5] => User port 5, ...,C_PORT_ENABLE[0] => User port 0 // Should the C_MEM_ADDR_ORDER made available to user ?? parameter C_MEM_ADDR_ORDER = "BANK_ROW_COLUMN" , //RowBankCol//ADDR_ORDER_MC : 0: Bank Row Col 1: Row Bank Col. User Address mapping oreder //////////////////////////////////////////////////////////////////////////////////////////////// // The parameter belows are not exposed to non-embedded users. // for now this arb_time_slot_x attributes will not exposed to user and will be generated from MIG tool // to translate the logical port to physical port. For advance user, translate the logical port // to physical port before passing them to this wrapper. // MIG need to save the user setting in project file. parameter C_ARB_NUM_TIME_SLOTS = 12, // For advance mode, allow user to either choose 10 or 12 parameter C_ARB_TIME_SLOT_0 = 18'o012345, // Config 1: "B32_B32_X32_X32_X32_X32" parameter C_ARB_TIME_SLOT_1 = 18'o123450, // User port 0 --->MCB port 0,User port 1 --->MCB port 1 parameter C_ARB_TIME_SLOT_2 = 18'o234501, // User port 2 --->MCB port 2,User port 3 --->MCB port 3 parameter C_ARB_TIME_SLOT_3 = 18'o345012, // User port 4 --->MCB port 4,User port 5 --->MCB port 5 parameter C_ARB_TIME_SLOT_4 = 18'o450123, // Config 2: "B32_B32_B32_B32" parameter C_ARB_TIME_SLOT_5 = 18'o501234, // User port 0 ---> MCB port 0 parameter C_ARB_TIME_SLOT_6 = 18'o012345, // User port 1 ---> MCB port 1 parameter C_ARB_TIME_SLOT_7 = 18'o123450, // User port 2 ---> MCB port 2 parameter C_ARB_TIME_SLOT_8 = 18'o234501, // User port 3 ---> MCB port 4 parameter C_ARB_TIME_SLOT_9 = 18'o345012, // Config 3: "B64_B32_B3" parameter C_ARB_TIME_SLOT_10 = 18'o450123, // User port 0 ---> MCB port 0 parameter C_ARB_TIME_SLOT_11 = 18'o501234, // User port 1 ---> MCB port 2 // User port 2 ---> MCB port 4 // Config 4: "B64_B64" // User port 0 ---> MCB port 0 // User port 1 ---> MCB port 2 // Config 5 "B128" // User port 0 ---> MCB port 0 parameter C_PORT_CONFIG = "B128", // Memory Timings parameter C_MEM_TRAS = 45000, //CEIL (tRAS/tCK) parameter C_MEM_TRCD = 12500, //CEIL (tRCD/tCK) parameter C_MEM_TREFI = 7800, //CEIL (tREFI/tCK) number of clocks parameter C_MEM_TRFC = 127500, //CEIL (tRFC/tCK) parameter C_MEM_TRP = 12500, //CEIL (tRP/tCK) parameter C_MEM_TWR = 15000, //CEIL (tWR/tCK) parameter C_MEM_TRTP = 7500, //CEIL (tRTP/tCK) parameter C_MEM_TWTR = 7500, parameter C_NUM_DQ_PINS = 8, parameter C_MEM_TYPE = "DDR3", parameter C_MEM_DENSITY = "512M", parameter C_MEM_BURST_LEN = 8, // MIG Rules for setting this parameter // For DDR3 this one always set to 8; // For DDR2 Config 1 : MemWidth x8,x16:=> 4; MemWidth x4 => 8 // Config 2 : MemWidth x8,x16:=> 4; MemWidth x4 => 8 // Config 3 : Data Port Width: 32 MemWidth x8,x16:=> 4; MemWidth x4 => 8 // Data Port Width: 64 MemWidth x16 :=> 4; MemWidth x8,x4 => 8 // Config 4 : Data Port Width: 64 MemWidth x16 :=> 4; MemWidth x4,x8, => 8 // Config 5 : Data Port Width: 128 MemWidth x4, x8,x16: => 8 parameter C_MEM_CAS_LATENCY = 4, parameter C_MEM_ADDR_WIDTH = 13, // extracted from selected Memory part parameter C_MEM_BANKADDR_WIDTH = 3, // extracted from selected Memory part parameter C_MEM_NUM_COL_BITS = 11, // extracted from selected Memory part parameter C_MEM_DDR3_CAS_LATENCY = 7, parameter C_MEM_MOBILE_PA_SR = "FULL", //"FULL", "HALF" Mobile DDR Partial Array Self-Refresh parameter C_MEM_DDR1_2_ODS = "FULL", //"FULL" :REDUCED" parameter C_MEM_DDR3_ODS = "DIV6", parameter C_MEM_DDR2_RTT = "50OHMS", parameter C_MEM_DDR3_RTT = "DIV2", parameter C_MEM_MDDR_ODS = "FULL", parameter C_MEM_DDR2_DIFF_DQS_EN = "YES", parameter C_MEM_DDR2_3_PA_SR = "OFF", parameter C_MEM_DDR3_CAS_WR_LATENCY = 5, // this parameter is hardcoded by MIG tool which depends on the memory clock frequency //C_MEMCLK_PERIOD ave = 2.5ns to < 3.3 ns, CWL = 5 //C_MEMCLK_PERIOD ave = 1.875ns to < 2.5 ns, CWL = 6 //C_MEMCLK_PERIOD ave = 1.5ns to <1.875ns, CSL = 7 //C_MEMCLK_PERIOD avg = 1.25ns to < 1.5ns , CWL = 8 parameter C_MEM_DDR3_AUTO_SR = "ENABLED", parameter C_MEM_DDR2_3_HIGH_TEMP_SR = "NORMAL", parameter C_MEM_DDR3_DYN_WRT_ODT = "OFF", parameter C_MEM_TZQINIT_MAXCNT = 10'd512, // DDR3 Minimum delay between resets //Calibration parameter C_MC_CALIB_BYPASS = "NO", parameter C_MC_CALIBRATION_RA = 15'h0000, parameter C_MC_CALIBRATION_BA = 3'h0, parameter C_CALIB_SOFT_IP = "TRUE", parameter C_SKIP_IN_TERM_CAL = 1'b0, //provides option to skip the input termination calibration parameter C_SKIP_DYNAMIC_CAL = 1'b0, //provides option to skip the dynamic delay calibration parameter C_SKIP_DYN_IN_TERM = 1'b1, // provides option to skip the input termination calibration parameter C_SIMULATION = "FALSE", // Tells us whether the design is being simulated or implemented ////////////////LUMP DELAY Params //////////////////////////// /// ADDED for 1.0 silicon support to bypass Calibration ////// /// 07-10-09 chipl ////////////////////////////////////////////////////////////// parameter LDQSP_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter UDQSP_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter LDQSN_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter UDQSN_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ0_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ1_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ2_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ3_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ4_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ5_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ6_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ7_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ8_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ9_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ10_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ11_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ12_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ13_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ14_TAP_DELAY_VAL = 0, // 0 to 255 inclusive parameter DQ15_TAP_DELAY_VAL = 0, // 0 to 255 inclusive //************* // MIG tool need to do DRC on this parameter to make sure this is valid Column address to avoid boundary crossing for the current Burst Size setting. parameter C_MC_CALIBRATION_CA = 12'h000, parameter C_MC_CALIBRATION_CLK_DIV = 1, parameter C_MC_CALIBRATION_MODE = "CALIBRATION" , // "CALIBRATION", "NOCALIBRATION" parameter C_MC_CALIBRATION_DELAY = "HALF", // "QUARTER", "HALF","THREEQUARTER", "FULL" parameter C_P0_MASK_SIZE = 4, parameter C_P0_DATA_PORT_SIZE = 32, parameter C_P1_MASK_SIZE = 4, parameter C_P1_DATA_PORT_SIZE = 32 ) ( // high-speed PLL clock interface input sysclk_2x, input sysclk_2x_180, input pll_ce_0, input pll_ce_90, input pll_lock, input sys_rst, // Not needed as ioi netlist are not used //*********************************************************************************** // Below User Port siganls needs to be customized when generating codes from MIG tool // The corresponding internal codes that directly use the commented out port signals // needs to be removed when gernerating wrapper outputs. //!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! //User Port0 Interface Signals // p0_xxxx signals shows up in Config 1 , Config 2 , Config 3, Config4 and Config 5 // cmd port 0 signals input p0_arb_en, input p0_cmd_clk, input p0_cmd_en, input [2:0] p0_cmd_instr, input [5:0] p0_cmd_bl, input [29:0] p0_cmd_byte_addr, output p0_cmd_empty, output p0_cmd_full, // Data Wr Port signals // p0_wr_xx signals shows up in Config 1 // p0_wr_xx signals shows up in Config 2 // p0_wr_xx signals shows up in Config 3 // p0_wr_xx signals shows up in Config 4 // p0_wr_xx signals shows up in Config 5 input p0_wr_clk, input p0_wr_en, input [C_P0_MASK_SIZE - 1:0] p0_wr_mask, input [C_P0_DATA_PORT_SIZE - 1:0] p0_wr_data, output p0_wr_full, // output p0_wr_empty,// output [6:0] p0_wr_count,// output p0_wr_underrun,// output p0_wr_error,// //Data Rd Port signals // p0_rd_xx signals shows up in Config 1 // p0_rd_xx signals shows up in Config 2 // p0_rd_xx signals shows up in Config 3 // p0_rd_xx signals shows up in Config 4 // p0_rd_xx signals shows up in Config 5 input p0_rd_clk, input p0_rd_en, output [C_P0_DATA_PORT_SIZE - 1:0] p0_rd_data, output p0_rd_full,// output p0_rd_empty,// output [6:0] p0_rd_count, output p0_rd_overflow,// output p0_rd_error,// //**************************** //User Port1 Interface Signals // This group of signals only appear on Config 1,2,3,4 when generated from MIG tool input p1_arb_en, input p1_cmd_clk, input p1_cmd_en, input [2:0] p1_cmd_instr, input [5:0] p1_cmd_bl, input [29:0] p1_cmd_byte_addr, output p1_cmd_empty, output p1_cmd_full, // Data Wr Port signals input p1_wr_clk, input p1_wr_en, input [C_P1_MASK_SIZE - 1:0] p1_wr_mask, input [C_P1_DATA_PORT_SIZE - 1:0] p1_wr_data, output p1_wr_full, output p1_wr_empty, output [6:0] p1_wr_count, output p1_wr_underrun, output p1_wr_error, //Data Rd Port signals input p1_rd_clk, input p1_rd_en, output [C_P1_DATA_PORT_SIZE - 1:0] p1_rd_data, output p1_rd_full, output p1_rd_empty, output [6:0] p1_rd_count, output p1_rd_overflow, output p1_rd_error, //**************************** //User Port2 Interface Signals // This group of signals only appear on Config 1,2,3 when generated from MIG tool // p2_xxxx signals shows up in Config 1 , Config 2 and Config 3 // p_cmd port 2 signals input p2_arb_en, input p2_cmd_clk, input p2_cmd_en, input [2:0] p2_cmd_instr, input [5:0] p2_cmd_bl, input [29:0] p2_cmd_byte_addr, output p2_cmd_empty, output p2_cmd_full, // Data Wr Port signals // p2_wr_xx signals shows up in Config 1 and Wr Dir // p2_wr_xx signals shows up in Config 2 // p2_wr_xx signals shows up in Config 3 input p2_wr_clk, input p2_wr_en, input [3:0] p2_wr_mask, input [31:0] p2_wr_data, output p2_wr_full, output p2_wr_empty, output [6:0] p2_wr_count, output p2_wr_underrun, output p2_wr_error, //Data Rd Port signals // p2_rd_xx signals shows up in Config 1 and Rd Dir // p2_rd_xx signals shows up in Config 2 // p2_rd_xx signals shows up in Config 3 input p2_rd_clk, input p2_rd_en, output [31:0] p2_rd_data, output p2_rd_full, output p2_rd_empty, output [6:0] p2_rd_count, output p2_rd_overflow, output p2_rd_error, //**************************** //User Port3 Interface Signals // This group of signals only appear on Config 1,2 when generated from MIG tool input p3_arb_en, input p3_cmd_clk, input p3_cmd_en, input [2:0] p3_cmd_instr, input [5:0] p3_cmd_bl, input [29:0] p3_cmd_byte_addr, output p3_cmd_empty, output p3_cmd_full, // Data Wr Port signals // p3_wr_xx signals shows up in Config 1 and Wr Dir // p3_wr_xx signals shows up in Config 2 input p3_wr_clk, input p3_wr_en, input [3:0] p3_wr_mask, input [31:0] p3_wr_data, output p3_wr_full, output p3_wr_empty, output [6:0] p3_wr_count, output p3_wr_underrun, output p3_wr_error, //Data Rd Port signals // p3_rd_xx signals shows up in Config 1 and Rd Dir when generated from MIG ttols // p3_rd_xx signals shows up in Config 2 input p3_rd_clk, input p3_rd_en, output [31:0] p3_rd_data, output p3_rd_full, output p3_rd_empty, output [6:0] p3_rd_count, output p3_rd_overflow, output p3_rd_error, //**************************** //User Port4 Interface Signals // This group of signals only appear on Config 1,2,3,4 when generated from MIG tool // p4_xxxx signals only shows up in Config 1 input p4_arb_en, input p4_cmd_clk, input p4_cmd_en, input [2:0] p4_cmd_instr, input [5:0] p4_cmd_bl, input [29:0] p4_cmd_byte_addr, output p4_cmd_empty, output p4_cmd_full, // Data Wr Port signals // p4_wr_xx signals only shows up in Config 1 and Wr Dir input p4_wr_clk, input p4_wr_en, input [3:0] p4_wr_mask, input [31:0] p4_wr_data, output p4_wr_full, output p4_wr_empty, output [6:0] p4_wr_count, output p4_wr_underrun, output p4_wr_error, //Data Rd Port signals // p4_rd_xx signals only shows up in Config 1 and Rd Dir input p4_rd_clk, input p4_rd_en, output [31:0] p4_rd_data, output p4_rd_full, output p4_rd_empty, output [6:0] p4_rd_count, output p4_rd_overflow, output p4_rd_error, //**************************** //User Port5 Interface Signals // p5_xxxx signals only shows up in Config 1; p5_wr_xx or p5_rd_xx depends on the user port settings input p5_arb_en, input p5_cmd_clk, input p5_cmd_en, input [2:0] p5_cmd_instr, input [5:0] p5_cmd_bl, input [29:0] p5_cmd_byte_addr, output p5_cmd_empty, output p5_cmd_full, // Data Wr Port signals input p5_wr_clk, input p5_wr_en, input [3:0] p5_wr_mask, input [31:0] p5_wr_data, output p5_wr_full, output p5_wr_empty, output [6:0] p5_wr_count, output p5_wr_underrun, output p5_wr_error, //Data Rd Port signals input p5_rd_clk, input p5_rd_en, output [31:0] p5_rd_data, output p5_rd_full, output p5_rd_empty, output [6:0] p5_rd_count, output p5_rd_overflow, output p5_rd_error, //***************************************************** // memory interface signals output [C_MEM_ADDR_WIDTH-1:0] mcbx_dram_addr, output [C_MEM_BANKADDR_WIDTH-1:0] mcbx_dram_ba, output mcbx_dram_ras_n, output mcbx_dram_cas_n, output mcbx_dram_we_n, output mcbx_dram_cke, output mcbx_dram_clk, output mcbx_dram_clk_n, inout [C_NUM_DQ_PINS-1:0] mcbx_dram_dq, inout mcbx_dram_dqs, inout mcbx_dram_dqs_n, inout mcbx_dram_udqs, inout mcbx_dram_udqs_n, output mcbx_dram_udm, output mcbx_dram_ldm, output mcbx_dram_odt, output mcbx_dram_ddr3_rst, // Calibration signals input calib_recal, // Input signal to trigger calibration // output calib_done, // 0=calibration not done or is in progress. // 1=calibration is complete. Also a MEM_READY indicator //Input - RZQ pin from board - expected to have a 2*R resistor to ground //Input - Z-stated IO pin - either unbonded IO, or IO garanteed not to be driven externally inout rzq, // RZQ pin from board - expected to have a 2*R resistor to ground inout zio, // Z-stated IO pin - either unbonded IO, or IO garanteed not to be driven externally // new added signals ********************************* // these signals are for dynamic Calibration IP input ui_read, input ui_add, input ui_cs, input ui_clk, input ui_sdi, input [4:0] ui_addr, input ui_broadcast, input ui_drp_update, input ui_done_cal, input ui_cmd, input ui_cmd_in, input ui_cmd_en, input [3:0] ui_dqcount, input ui_dq_lower_dec, input ui_dq_lower_inc, input ui_dq_upper_dec, input ui_dq_upper_inc, input ui_udqs_inc, input ui_udqs_dec, input ui_ldqs_inc, input ui_ldqs_dec, output [7:0] uo_data, output uo_data_valid, output uo_done_cal, output uo_cmd_ready_in, output uo_refrsh_flag, output uo_cal_start, output uo_sdo, output [31:0] status, input selfrefresh_enter, output selfrefresh_mode ); function integer cdiv (input integer num, input integer div); // ceiling divide begin cdiv = (num/div) + (((num%div)>0) ? 1 : 0); end endfunction // cdiv // parameters added by AM for OSERDES2 12/09/2008, these parameters may not have to change localparam C_OSERDES2_DATA_RATE_OQ = "SDR"; //SDR, DDR localparam C_OSERDES2_DATA_RATE_OT = "SDR"; //SDR, DDR localparam C_OSERDES2_SERDES_MODE_MASTER = "MASTER"; //MASTER, SLAVE localparam C_OSERDES2_SERDES_MODE_SLAVE = "SLAVE"; //MASTER, SLAVE localparam C_OSERDES2_OUTPUT_MODE_SE = "SINGLE_ENDED"; //SINGLE_ENDED, DIFFERENTIAL localparam C_OSERDES2_OUTPUT_MODE_DIFF = "DIFFERENTIAL"; localparam C_BUFPLL_0_LOCK_SRC = "LOCK_TO_0"; localparam C_DQ_IODRP2_DATA_RATE = "SDR"; localparam C_DQ_IODRP2_SERDES_MODE_MASTER = "MASTER"; localparam C_DQ_IODRP2_SERDES_MODE_SLAVE = "SLAVE"; localparam C_DQS_IODRP2_DATA_RATE = "SDR"; localparam C_DQS_IODRP2_SERDES_MODE_MASTER = "MASTER"; localparam C_DQS_IODRP2_SERDES_MODE_SLAVE = "SLAVE"; // MIG always set the below ADD_LATENCY to zero localparam C_MEM_DDR3_ADD_LATENCY = "OFF"; localparam C_MEM_DDR2_ADD_LATENCY = 0; localparam C_MEM_MOBILE_TC_SR = 0; // not supported ////////////////////////////////////////////////////////////////////////////////// // Attribute Declarations // Attributes set from GUI // // // the local param for the time slot varis according to User Port Configuration // This section also needs to be customized when gernerating wrapper outputs. //***************************************************************************** // For Configuration 1 and this section will be used in RAW file localparam arbtimeslot0 = {C_ARB_TIME_SLOT_0 }; localparam arbtimeslot1 = {C_ARB_TIME_SLOT_1 }; localparam arbtimeslot2 = {C_ARB_TIME_SLOT_2 }; localparam arbtimeslot3 = {C_ARB_TIME_SLOT_3 }; localparam arbtimeslot4 = {C_ARB_TIME_SLOT_4 }; localparam arbtimeslot5 = {C_ARB_TIME_SLOT_5 }; localparam arbtimeslot6 = {C_ARB_TIME_SLOT_6 }; localparam arbtimeslot7 = {C_ARB_TIME_SLOT_7 }; localparam arbtimeslot8 = {C_ARB_TIME_SLOT_8 }; localparam arbtimeslot9 = {C_ARB_TIME_SLOT_9 }; localparam arbtimeslot10 = {C_ARB_TIME_SLOT_10 }; localparam arbtimeslot11 = {C_ARB_TIME_SLOT_11 }; // convert the memory timing to memory clock units. I localparam MEM_RAS_VAL = ((C_MEM_TRAS + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD); localparam MEM_RCD_VAL = ((C_MEM_TRCD + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD); localparam MEM_REFI_VAL = ((C_MEM_TREFI + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD) - 25; localparam MEM_RFC_VAL = ((C_MEM_TRFC + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD); localparam MEM_RP_VAL = ((C_MEM_TRP + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD); localparam MEM_WR_VAL = ((C_MEM_TWR + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD); localparam MEM_RTP_CK = cdiv(C_MEM_TRTP,C_MEMCLK_PERIOD); localparam MEM_RTP_VAL = (C_MEM_TYPE == "DDR3") ? (MEM_RTP_CK < 4) ? 4 : MEM_RTP_CK : (MEM_RTP_CK < 2) ? 2 : MEM_RTP_CK; localparam MEM_WTR_VAL = (C_MEM_TYPE == "DDR") ? 2 : (C_MEM_TYPE == "DDR3") ? 4 : (C_MEM_TYPE == "MDDR") ? C_MEM_TWTR : (C_MEM_TYPE == "LPDDR") ? C_MEM_TWTR : ((C_MEM_TYPE == "DDR2") && (((C_MEM_TWTR + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD) > 2)) ? ((C_MEM_TWTR + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD) : (C_MEM_TYPE == "DDR2") ? 2 : 3 ; localparam C_MEM_DDR2_WRT_RECOVERY = (C_MEM_TYPE != "DDR2") ? 5: ((C_MEM_TWR + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD); localparam C_MEM_DDR3_WRT_RECOVERY = (C_MEM_TYPE != "DDR3") ? 5: ((C_MEM_TWR + C_MEMCLK_PERIOD -1) /C_MEMCLK_PERIOD); //localparam MEM_TYPE = (C_MEM_TYPE == "LPDDR") ? "MDDR": C_MEM_TYPE; //////////////////////////////////////////////////////////////////////////// // wire Declarations //////////////////////////////////////////////////////////////////////////// wire [31:0] addr_in0; reg [127:0] allzero = 0; // UNISIM Model <-> IOI //dqs clock network interface wire dqs_out_p; wire dqs_out_n; wire dqs_sys_p; //from dqs_gen to IOclk network wire dqs_sys_n; //from dqs_gen to IOclk network wire udqs_sys_p; wire udqs_sys_n; wire dqs_p; // open net now ? wire dqs_n; // open net now ? // IOI and IOB enable/tristate interface wire dqIO_w_en_0; //enable DQ pads wire dqsIO_w_en_90_p; //enable p side of DQS wire dqsIO_w_en_90_n; //enable n side of DQS //memory chip control interface wire [14:0] address_90; wire [2:0] ba_90; wire ras_90; wire cas_90; wire we_90 ; wire cke_90; wire odt_90; wire rst_90; // calibration IDELAY control signals wire ioi_drp_clk; //DRP interface - synchronous clock output wire [4:0] ioi_drp_addr; //DRP interface - IOI selection wire ioi_drp_sdo; //DRP interface - serial output for commmands wire ioi_drp_sdi; //DRP interface - serial input for commands wire ioi_drp_cs; //DRP interface - chip select doubles as DONE signal wire ioi_drp_add; //DRP interface - serial address signal wire ioi_drp_broadcast; wire ioi_drp_train; // Calibration datacapture siganls wire [3:0]dqdonecount; //select signal for the datacapture 16 to 1 mux wire dq_in_p; //positive signal sent to calibration logic wire dq_in_n; //negative signal sent to calibration logic wire cal_done; //DQS calibration interface wire udqs_n; wire udqs_p; wire udqs_dqocal_p; wire udqs_dqocal_n; // MUI enable interface wire df_en_n90 ; //INTERNAL SIGNAL FOR DRP chain // IOI <-> MUI wire ioi_int_tmp; wire [15:0]dqo_n; wire [15:0]dqo_p; wire dqnlm; wire dqplm; wire dqnum; wire dqpum; // IOI <-> IOB routes wire [C_MEM_ADDR_WIDTH-1:0]ioi_addr; wire [C_MEM_BANKADDR_WIDTH-1:0]ioi_ba; wire ioi_cas; wire ioi_ck; wire ioi_ckn; wire ioi_cke; wire [C_NUM_DQ_PINS-1:0]ioi_dq; wire ioi_dqs; wire ioi_dqsn; wire ioi_udqs; wire ioi_udqsn; wire ioi_odt; wire ioi_ras; wire ioi_rst; wire ioi_we; wire ioi_udm; wire ioi_ldm; wire [15:0] in_dq; wire [C_NUM_DQ_PINS-1:0] in_pre_dq; wire in_dqs; wire in_pre_dqsp; wire in_pre_dqsn; wire in_pre_udqsp; wire in_pre_udqsn; wire in_udqs; // Memory tri-state control signals wire [C_MEM_ADDR_WIDTH-1:0]t_addr; wire [C_MEM_BANKADDR_WIDTH-1:0]t_ba; wire t_cas; wire t_ck ; wire t_ckn; wire t_cke; wire [C_NUM_DQ_PINS-1:0]t_dq; wire t_dqs; wire t_dqsn; wire t_udqs; wire t_udqsn; wire t_odt; wire t_ras; wire t_rst; wire t_we ; wire t_udm ; wire t_ldm ; wire idelay_dqs_ioi_s; wire idelay_dqs_ioi_m; wire idelay_udqs_ioi_s; wire idelay_udqs_ioi_m; wire dqs_pin; wire udqs_pin; // USER Interface signals // translated memory addresses wire [14:0]p0_cmd_ra; wire [2:0]p0_cmd_ba; wire [11:0]p0_cmd_ca; wire [14:0]p1_cmd_ra; wire [2:0]p1_cmd_ba; wire [11:0]p1_cmd_ca; wire [14:0]p2_cmd_ra; wire [2:0]p2_cmd_ba; wire [11:0]p2_cmd_ca; wire [14:0]p3_cmd_ra; wire [2:0]p3_cmd_ba; wire [11:0]p3_cmd_ca; wire [14:0]p4_cmd_ra; wire [2:0]p4_cmd_ba; wire [11:0]p4_cmd_ca; wire [14:0]p5_cmd_ra; wire [2:0]p5_cmd_ba; wire [11:0]p5_cmd_ca; // user command wires mapped from logical ports to physical ports wire mig_p0_arb_en; wire mig_p0_cmd_clk; wire mig_p0_cmd_en; wire [14:0] mig_p0_cmd_ra; wire [2:0] mig_p0_cmd_ba; wire [11:0] mig_p0_cmd_ca; wire [2:0] mig_p0_cmd_instr; wire [5:0] mig_p0_cmd_bl; wire mig_p0_cmd_empty; wire mig_p0_cmd_full; wire mig_p1_arb_en; wire mig_p1_cmd_clk; wire mig_p1_cmd_en; wire [14:0] mig_p1_cmd_ra; wire [2:0] mig_p1_cmd_ba; wire [11:0] mig_p1_cmd_ca; wire [2:0] mig_p1_cmd_instr; wire [5:0] mig_p1_cmd_bl; wire mig_p1_cmd_empty; wire mig_p1_cmd_full; wire mig_p2_arb_en; wire mig_p2_cmd_clk; wire mig_p2_cmd_en; wire [14:0] mig_p2_cmd_ra; wire [2:0] mig_p2_cmd_ba; wire [11:0] mig_p2_cmd_ca; wire [2:0] mig_p2_cmd_instr; wire [5:0] mig_p2_cmd_bl; wire mig_p2_cmd_empty; wire mig_p2_cmd_full; wire mig_p3_arb_en; wire mig_p3_cmd_clk; wire mig_p3_cmd_en; wire [14:0] mig_p3_cmd_ra; wire [2:0] mig_p3_cmd_ba; wire [11:0] mig_p3_cmd_ca; wire [2:0] mig_p3_cmd_instr; wire [5:0] mig_p3_cmd_bl; wire mig_p3_cmd_empty; wire mig_p3_cmd_full; wire mig_p4_arb_en; wire mig_p4_cmd_clk; wire mig_p4_cmd_en; wire [14:0] mig_p4_cmd_ra; wire [2:0] mig_p4_cmd_ba; wire [11:0] mig_p4_cmd_ca; wire [2:0] mig_p4_cmd_instr; wire [5:0] mig_p4_cmd_bl; wire mig_p4_cmd_empty; wire mig_p4_cmd_full; wire mig_p5_arb_en; wire mig_p5_cmd_clk; wire mig_p5_cmd_en; wire [14:0] mig_p5_cmd_ra; wire [2:0] mig_p5_cmd_ba; wire [11:0] mig_p5_cmd_ca; wire [2:0] mig_p5_cmd_instr; wire [5:0] mig_p5_cmd_bl; wire mig_p5_cmd_empty; wire mig_p5_cmd_full; wire mig_p0_wr_clk; wire mig_p0_rd_clk; wire mig_p1_wr_clk; wire mig_p1_rd_clk; wire mig_p2_clk; wire mig_p3_clk; wire mig_p4_clk; wire mig_p5_clk; wire mig_p0_wr_en; wire mig_p0_rd_en; wire mig_p1_wr_en; wire mig_p1_rd_en; wire mig_p2_en; wire mig_p3_en; wire mig_p4_en; wire mig_p5_en; wire [31:0]mig_p0_wr_data; wire [31:0]mig_p1_wr_data; wire [31:0]mig_p2_wr_data; wire [31:0]mig_p3_wr_data; wire [31:0]mig_p4_wr_data; wire [31:0]mig_p5_wr_data; wire [C_P0_MASK_SIZE-1:0]mig_p0_wr_mask; wire [C_P1_MASK_SIZE-1:0]mig_p1_wr_mask; wire [3:0]mig_p2_wr_mask; wire [3:0]mig_p3_wr_mask; wire [3:0]mig_p4_wr_mask; wire [3:0]mig_p5_wr_mask; wire [31:0]mig_p0_rd_data; wire [31:0]mig_p1_rd_data; wire [31:0]mig_p2_rd_data; wire [31:0]mig_p3_rd_data; wire [31:0]mig_p4_rd_data; wire [31:0]mig_p5_rd_data; wire mig_p0_rd_overflow; wire mig_p1_rd_overflow; wire mig_p2_overflow; wire mig_p3_overflow; wire mig_p4_overflow; wire mig_p5_overflow; wire mig_p0_wr_underrun; wire mig_p1_wr_underrun; wire mig_p2_underrun; wire mig_p3_underrun; wire mig_p4_underrun; wire mig_p5_underrun; wire mig_p0_rd_error; wire mig_p0_wr_error; wire mig_p1_rd_error; wire mig_p1_wr_error; wire mig_p2_error; wire mig_p3_error; wire mig_p4_error; wire mig_p5_error; wire [6:0]mig_p0_wr_count; wire [6:0]mig_p1_wr_count; wire [6:0]mig_p0_rd_count; wire [6:0]mig_p1_rd_count; wire [6:0]mig_p2_count; wire [6:0]mig_p3_count; wire [6:0]mig_p4_count; wire [6:0]mig_p5_count; wire mig_p0_wr_full; wire mig_p1_wr_full; wire mig_p0_rd_empty; wire mig_p1_rd_empty; wire mig_p0_wr_empty; wire mig_p1_wr_empty; wire mig_p0_rd_full; wire mig_p1_rd_full; wire mig_p2_full; wire mig_p3_full; wire mig_p4_full; wire mig_p5_full; wire mig_p2_empty; wire mig_p3_empty; wire mig_p4_empty; wire mig_p5_empty; // SELFREESH control signal for suspend feature wire selfrefresh_mcb_enter; wire selfrefresh_mcb_mode ; // Testing Interface signals wire tst_cmd_test_en; wire [7:0] tst_sel; wire [15:0] tst_in; wire tst_scan_clk; wire tst_scan_rst; wire tst_scan_set; wire tst_scan_en; wire tst_scan_in; wire tst_scan_mode; wire p0w_tst_en; wire p0r_tst_en; wire p1w_tst_en; wire p1r_tst_en; wire p2_tst_en; wire p3_tst_en; wire p4_tst_en; wire p5_tst_en; wire p0_tst_wr_clk_en; wire p0_tst_rd_clk_en; wire p1_tst_wr_clk_en; wire p1_tst_rd_clk_en; wire p2_tst_clk_en; wire p3_tst_clk_en; wire p4_tst_clk_en; wire p5_tst_clk_en; wire [3:0] p0w_tst_wr_mode; wire [3:0] p0r_tst_mode; wire [3:0] p1w_tst_wr_mode; wire [3:0] p1r_tst_mode; wire [3:0] p2_tst_mode; wire [3:0] p3_tst_mode; wire [3:0] p4_tst_mode; wire [3:0] p5_tst_mode; wire p0r_tst_pin_en; wire p0w_tst_pin_en; wire p1r_tst_pin_en; wire p1w_tst_pin_en; wire p2_tst_pin_en; wire p3_tst_pin_en; wire p4_tst_pin_en; wire p5_tst_pin_en; wire p0w_tst_overflow; wire p1w_tst_overflow; wire [3:0] p0r_tst_mask_o; wire [3:0] p0w_tst_mask_o; wire [3:0] p1r_tst_mask_o; wire [3:0] p1w_tst_mask_o; wire [3:0] p2_tst_mask_o; wire [3:0] p3_tst_mask_o; wire [3:0] p4_tst_mask_o; wire [3:0] p5_tst_mask_o; wire [3:0] p0r_tst_wr_mask; wire [3:0] p1r_tst_wr_mask; wire [31:0] p1r_tst_wr_data; wire [31:0] p0r_tst_wr_data; wire [31:0] p0w_tst_rd_data; wire [31:0] p1w_tst_rd_data; wire [38:0] tst_cmd_out; wire MCB_SYSRST; wire ioclk0; wire ioclk90; wire mcb_ui_clk; wire hard_done_cal; wire cke_train; //testing wire ioi_drp_update; wire [7:0] aux_sdi_sdo; wire [4:0] mcb_ui_addr; wire [3:0] mcb_ui_dqcount; reg syn_uiclk_pll_lock; wire int_sys_rst /* synthesis syn_maxfan = 1 */; // synthesis attribute max_fanout of int_sys_rst is 1 reg [15:0] wait_200us_counter; reg cke_train_reg; reg wait_200us_done_r1,wait_200us_done_r2; assign ioclk0 = sysclk_2x; assign ioclk90 = sysclk_2x_180; //Added 2/22 - Add flop to pll_lock status signal to improve timing always @ (posedge ui_clk) begin syn_uiclk_pll_lock <= pll_lock; end assign int_sys_rst = sys_rst | ~syn_uiclk_pll_lock; //Address Remapping // Byte Address remapping // // Bank Address[x:0] & Row Address[x:0] & Column Address[x:0] // column address remap for port 0 generate // port bus remapping sections for CONFIG 2 15,3,12 if(C_NUM_DQ_PINS == 16) begin : x16_Addr if (C_MEM_ADDR_ORDER == "ROW_BANK_COLUMN") begin // C_MEM_ADDR_ORDER = 0 : Bank Row Column // port 0 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p0_cmd_ra = p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p0_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS :C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p0_cmd_ba = p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p0_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p0_cmd_ca = p0_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p0_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p0_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 1 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p1_cmd_ra = p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p1_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS :C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p1_cmd_ba = p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p1_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p1_cmd_ca = p1_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p1_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p1_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 2 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p2_cmd_ra = p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p2_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS :C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p2_cmd_ba = p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p2_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p2_cmd_ca = p2_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p2_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p2_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 3 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p3_cmd_ra = p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p3_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS :C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p3_cmd_ba = p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p3_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p3_cmd_ca = p3_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p3_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p3_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 4 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p4_cmd_ra = p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p4_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS :C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p4_cmd_ba = p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p4_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p4_cmd_ca = p4_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p4_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p4_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 5 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p5_cmd_ra = p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p5_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS :C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p5_cmd_ba = p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p5_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p5_cmd_ca = p5_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p5_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p5_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; end else // ***************C_MEM_ADDR_ORDER = 1 : Row Bank Column begin // port 0 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p0_cmd_ba = p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p0_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_ADDR_WIDTH == 15) assign p0_cmd_ra = p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p0_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p0_cmd_ca = p0_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p0_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p0_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 1 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p1_cmd_ba = p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p1_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_ADDR_WIDTH == 15) assign p1_cmd_ra = p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p1_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p1_cmd_ca = p1_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p1_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p1_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 2 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p2_cmd_ba = p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p2_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_ADDR_WIDTH == 15) assign p2_cmd_ra = p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p2_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p2_cmd_ca = p2_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p2_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p2_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 3 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p3_cmd_ba = p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p3_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_ADDR_WIDTH == 15) assign p3_cmd_ra = p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p3_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p3_cmd_ca = p3_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p3_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p3_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 4 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p4_cmd_ba = p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p4_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_ADDR_WIDTH == 15) assign p4_cmd_ra = p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p4_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p4_cmd_ca = p4_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p4_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p4_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; // port 5 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p5_cmd_ba = p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]; else assign p5_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH] , p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_ADDR_WIDTH == 15) assign p5_cmd_ra = p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]; else assign p5_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS : C_MEM_NUM_COL_BITS + 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p5_cmd_ca = p5_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]; else assign p5_cmd_ca = {allzero[12:C_MEM_NUM_COL_BITS + 1], p5_cmd_byte_addr[C_MEM_NUM_COL_BITS : 1]}; end end else if(C_NUM_DQ_PINS == 8) begin : x8_Addr if (C_MEM_ADDR_ORDER == "ROW_BANK_COLUMN") begin // C_MEM_ADDR_ORDER = 1 : Bank Row Column // port 0 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p0_cmd_ra = p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p0_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p0_cmd_ba = p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; //14,3,10 else assign p0_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; //14,3,10 if (C_MEM_NUM_COL_BITS == 12) //Column assign p0_cmd_ca[11:0] = p0_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p0_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p0_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 1 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p1_cmd_ra = p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p1_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p1_cmd_ba = p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; //14,3,10 else assign p1_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; //14,3,10 if (C_MEM_NUM_COL_BITS == 12) //Column assign p1_cmd_ca[11:0] = p1_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p1_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p1_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 2 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p2_cmd_ra = p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p2_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p2_cmd_ba = p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; //14,3,10 else assign p2_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; //14,2,10 *** if (C_MEM_NUM_COL_BITS == 12) //Column assign p2_cmd_ca[11:0] = p2_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p2_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p2_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 3 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p3_cmd_ra = p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p3_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p3_cmd_ba = p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; //14,3,10 else assign p3_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; //14,3,10 if (C_MEM_NUM_COL_BITS == 12) //Column assign p3_cmd_ca[11:0] = p3_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p3_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p3_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 4 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p4_cmd_ra = p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p4_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p4_cmd_ba = p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; //14,3,10 else assign p4_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; //14,3,10 if (C_MEM_NUM_COL_BITS == 12) //Column assign p4_cmd_ca[11:0] = p4_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p4_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p4_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 5 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p5_cmd_ra = p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p5_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p5_cmd_ba = p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; //14,3,10 else assign p5_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; //14,3,10 if (C_MEM_NUM_COL_BITS == 12) //Column assign p5_cmd_ca[11:0] = p5_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p5_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p5_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; end else // x8 ***************C_MEM_ADDR_ORDER = 0 : Bank Row Column begin // port 0 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p0_cmd_ba = p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p0_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p0_cmd_ra = p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; else assign p0_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p0_cmd_ca[11:0] = p0_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p0_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p0_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 1 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p1_cmd_ba = p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p1_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p1_cmd_ra = p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; else assign p1_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p1_cmd_ca[11:0] = p1_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p1_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p1_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; //port 2 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank 2,13,10 24,23 assign p2_cmd_ba = p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p2_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p2_cmd_ra = p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; else assign p2_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p2_cmd_ca[11:0] = p2_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p2_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p2_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 3 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p3_cmd_ba = p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p3_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p3_cmd_ra = p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; else assign p3_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p3_cmd_ca[11:0] = p3_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p3_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p3_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 4 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p4_cmd_ba = p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p4_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p4_cmd_ra = p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; else assign p4_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p4_cmd_ca[11:0] = p4_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p4_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p4_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; // port 5 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p5_cmd_ba = p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]; else assign p5_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH], p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS ]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p5_cmd_ra = p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]; else assign p5_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH] , p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1 : C_MEM_NUM_COL_BITS ]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p5_cmd_ca[11:0] = p5_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]; else assign p5_cmd_ca[11:0] = {allzero[11 : C_MEM_NUM_COL_BITS] , p5_cmd_byte_addr[C_MEM_NUM_COL_BITS - 1 : 0]}; end // end else if(C_NUM_DQ_PINS == 4) begin : x4_Addr if (C_MEM_ADDR_ORDER == "ROW_BANK_COLUMN") begin // C_MEM_ADDR_ORDER = 1 : Row Bank Column // port 0 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p0_cmd_ra = p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p0_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p0_cmd_ba = p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p0_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p0_cmd_ca = {p0_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; //14,3,11 else assign p0_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p0_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; // port 1 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p1_cmd_ra = p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p1_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p1_cmd_ba = p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p1_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p1_cmd_ca = {p1_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; //14,3,11 else assign p1_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p1_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; // port 2 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p2_cmd_ra = p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p2_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p2_cmd_ba = p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p2_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p2_cmd_ca = {p2_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; //14,3,11 else assign p2_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p2_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; // port 3 address remapping if (C_MEM_ADDR_WIDTH == 15) //Row assign p3_cmd_ra = p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p3_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p3_cmd_ba = p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p3_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p3_cmd_ca = {p3_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; //14,3,11 else assign p3_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p3_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; if(C_PORT_CONFIG == "B32_B32_R32_R32_R32_R32" || C_PORT_CONFIG == "B32_B32_R32_R32_R32_W32" || C_PORT_CONFIG == "B32_B32_R32_R32_W32_R32" || C_PORT_CONFIG == "B32_B32_R32_R32_W32_W32" || C_PORT_CONFIG == "B32_B32_R32_W32_R32_R32" || C_PORT_CONFIG == "B32_B32_R32_W32_R32_W32" || C_PORT_CONFIG == "B32_B32_R32_W32_W32_R32" || C_PORT_CONFIG == "B32_B32_R32_W32_W32_W32" || C_PORT_CONFIG == "B32_B32_W32_R32_R32_R32" || C_PORT_CONFIG == "B32_B32_W32_R32_R32_W32" || C_PORT_CONFIG == "B32_B32_W32_R32_W32_R32" || C_PORT_CONFIG == "B32_B32_W32_R32_W32_W32" || C_PORT_CONFIG == "B32_B32_W32_W32_R32_R32" || C_PORT_CONFIG == "B32_B32_W32_W32_R32_W32" || C_PORT_CONFIG == "B32_B32_W32_W32_W32_R32" || C_PORT_CONFIG == "B32_B32_W32_W32_W32_W32" ) //begin : x4_Addr_CFG1_OR_CFG2 begin if (C_MEM_ADDR_WIDTH == 15) //Row assign p4_cmd_ra = p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p4_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p4_cmd_ba = p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p4_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p4_cmd_ca = {p4_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; //14,3,11 else assign p4_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p4_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p5_cmd_ra = p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p5_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p5_cmd_ba = p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p5_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p5_cmd_ca = {p5_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; //14,3,11 else assign p5_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p5_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; end end else // C_MEM_ADDR_ORDER = 1 : Row Bank Column begin // port 0 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p0_cmd_ba = p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p0_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p0_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p0_cmd_ra = p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p0_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p0_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p0_cmd_ca = {p0_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; else assign p0_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p0_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; // port 1 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p1_cmd_ba = p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p1_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p1_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p1_cmd_ra = p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p1_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p1_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p1_cmd_ca = {p1_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; else assign p1_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p1_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; // port 2 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p2_cmd_ba = p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p2_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p2_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; //*** if (C_MEM_ADDR_WIDTH == 15) //Row assign p2_cmd_ra = p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p2_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p2_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p2_cmd_ca = {p2_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; else assign p2_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p2_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; // port 3 address remapping if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p3_cmd_ba = p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p3_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p3_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p3_cmd_ra = p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p3_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p3_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p3_cmd_ca = {p3_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; else assign p3_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p3_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; if(C_PORT_CONFIG == "B32_B32_R32_R32_R32_R32" || C_PORT_CONFIG == "B32_B32_R32_R32_R32_W32" || C_PORT_CONFIG == "B32_B32_R32_R32_W32_R32" || C_PORT_CONFIG == "B32_B32_R32_R32_W32_W32" || C_PORT_CONFIG == "B32_B32_R32_W32_R32_R32" || C_PORT_CONFIG == "B32_B32_R32_W32_R32_W32" || C_PORT_CONFIG == "B32_B32_R32_W32_W32_R32" || C_PORT_CONFIG == "B32_B32_R32_W32_W32_W32" || C_PORT_CONFIG == "B32_B32_W32_R32_R32_R32" || C_PORT_CONFIG == "B32_B32_W32_R32_R32_W32" || C_PORT_CONFIG == "B32_B32_W32_R32_W32_R32" || C_PORT_CONFIG == "B32_B32_W32_R32_W32_W32" || C_PORT_CONFIG == "B32_B32_W32_W32_R32_R32" || C_PORT_CONFIG == "B32_B32_W32_W32_R32_W32" || C_PORT_CONFIG == "B32_B32_W32_W32_W32_R32" || C_PORT_CONFIG == "B32_B32_W32_W32_W32_W32" ) //begin : x4_Addr_CFG1_OR_CFG2 begin if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p4_cmd_ba = p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p4_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p4_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p4_cmd_ra = p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p4_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p4_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p4_cmd_ca = {p4_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; else assign p4_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p4_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; if (C_MEM_BANKADDR_WIDTH == 3 ) //Bank assign p5_cmd_ba = p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]; else assign p5_cmd_ba = {allzero[2 : C_MEM_BANKADDR_WIDTH ] , p5_cmd_byte_addr[C_MEM_BANKADDR_WIDTH + C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_ADDR_WIDTH == 15) //Row assign p5_cmd_ra = p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]; else assign p5_cmd_ra = {allzero[14 : C_MEM_ADDR_WIDTH ] , p5_cmd_byte_addr[C_MEM_ADDR_WIDTH + C_MEM_NUM_COL_BITS - 2 : C_MEM_NUM_COL_BITS - 1]}; if (C_MEM_NUM_COL_BITS == 12) //Column assign p5_cmd_ca = {p5_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; else assign p5_cmd_ca = {allzero[11 : C_MEM_NUM_COL_BITS ] , p5_cmd_byte_addr[C_MEM_NUM_COL_BITS - 2 : 0] , 1'b0}; end end end // block: x4_Addr endgenerate generate // if(C_PORT_CONFIG[183:160] == "B32") begin : u_config1_0 if(C_PORT_CONFIG == "B32_B32_R32_R32_R32_R32" || C_PORT_CONFIG == "B32_B32_R32_R32_R32_W32" || C_PORT_CONFIG == "B32_B32_R32_R32_W32_R32" || C_PORT_CONFIG == "B32_B32_R32_R32_W32_W32" || C_PORT_CONFIG == "B32_B32_R32_W32_R32_R32" || C_PORT_CONFIG == "B32_B32_R32_W32_R32_W32" || C_PORT_CONFIG == "B32_B32_R32_W32_W32_R32" || C_PORT_CONFIG == "B32_B32_R32_W32_W32_W32" || C_PORT_CONFIG == "B32_B32_W32_R32_R32_R32" || C_PORT_CONFIG == "B32_B32_W32_R32_R32_W32" || C_PORT_CONFIG == "B32_B32_W32_R32_W32_R32" || C_PORT_CONFIG == "B32_B32_W32_R32_W32_W32" || C_PORT_CONFIG == "B32_B32_W32_W32_R32_R32" || C_PORT_CONFIG == "B32_B32_W32_W32_R32_W32" || C_PORT_CONFIG == "B32_B32_W32_W32_W32_R32" || C_PORT_CONFIG == "B32_B32_W32_W32_W32_W32" ) begin : u_config1_0 //synthesis translate_off always @(*) begin if ( C_PORT_CONFIG[119:96] == "W32" && p2_cmd_en == 1'b1 && p2_cmd_instr[2] == 1'b0 && p2_cmd_instr[0] == 1'b1 ) begin $display("ERROR - Invalid Command for write only port 2"); $finish; end end always @(*) begin if ( C_PORT_CONFIG[119:96] == "R32" && p2_cmd_en == 1'b1 && p2_cmd_instr[2] == 1'b0 && p2_cmd_instr[0] == 1'b0 ) begin $display("ERROR - Invalid Command for read only port 2"); $finish; end end // Catch Invalid command during simulation for Port 3 always @(*) begin if ( C_PORT_CONFIG[87:64] == "W32" && p3_cmd_en == 1'b1 && p3_cmd_instr[2] == 1'b0 && p3_cmd_instr[0] == 1'b1 ) begin $display("ERROR - Invalid Command for write only port 3"); $finish; end end always @(*) begin if ( C_PORT_CONFIG[87:64] == "R32" && p3_cmd_en == 1'b1 && p3_cmd_instr[2] == 1'b0 && p3_cmd_instr[0] == 1'b0 ) begin $display("ERROR - Invalid Command for read only port 3"); $finish; end end // Catch Invalid command during simulation for Port 4 always @(*) begin if ( C_PORT_CONFIG[55:32] == "W32" && p4_cmd_en == 1'b1 && p4_cmd_instr[2] == 1'b0 && p4_cmd_instr[0] == 1'b1 ) begin $display("ERROR - Invalid Command for write only port 4"); $finish; end end always @(*) begin if ( C_PORT_CONFIG[55:32] == "R32" && p4_cmd_en == 1'b1 && p4_cmd_instr[2] == 1'b0 && p4_cmd_instr[0] == 1'b0 ) begin $display("ERROR - Invalid Command for read only port 4"); $finish; end end // Catch Invalid command during simulation for Port 5 always @(*) begin if ( C_PORT_CONFIG[23:0] == "W32" && p5_cmd_en == 1'b1 && p5_cmd_instr[2] == 1'b0 && p5_cmd_instr[0] == 1'b1 ) begin $display("ERROR - Invalid Command for write only port 5"); $finish; end end always @(*) begin if ( C_PORT_CONFIG[23:0] == "R32" && p5_cmd_en == 1'b1 && p5_cmd_instr[2] == 1'b0 && p5_cmd_instr[0] == 1'b0 ) begin $display("ERROR - Invalid Command for read only port 5"); $finish; end end //synthesis translate_on // the local declaration of input port signals doesn't work. The mig_p1_xxx through mig_p5_xxx always ends up // high Z even though there are signals on p1_cmd_xxx through p5_cmd_xxxx. // The only solutions that I have is to have MIG tool remove the entire internal codes that doesn't belongs to the Configuration.. // // Inputs from Application CMD Port if (C_PORT_ENABLE[0] == 1'b1) begin assign mig_p0_arb_en = p0_arb_en ; assign mig_p0_cmd_clk = p0_cmd_clk ; assign mig_p0_cmd_en = p0_cmd_en ; assign mig_p0_cmd_ra = p0_cmd_ra ; assign mig_p0_cmd_ba = p0_cmd_ba ; assign mig_p0_cmd_ca = p0_cmd_ca ; assign mig_p0_cmd_instr = p0_cmd_instr; assign mig_p0_cmd_bl = {(p0_cmd_instr[2] | p0_cmd_bl[5]),p0_cmd_bl[4:0]} ; assign p0_cmd_empty = mig_p0_cmd_empty; assign p0_cmd_full = mig_p0_cmd_full ; end else begin assign mig_p0_arb_en = 'b0; assign mig_p0_cmd_clk = 'b0; assign mig_p0_cmd_en = 'b0; assign mig_p0_cmd_ra = 'b0; assign mig_p0_cmd_ba = 'b0; assign mig_p0_cmd_ca = 'b0; assign mig_p0_cmd_instr = 'b0; assign mig_p0_cmd_bl = 'b0; assign p0_cmd_empty = 'b0; assign p0_cmd_full = 'b0; end if (C_PORT_ENABLE[1] == 1'b1) begin assign mig_p1_arb_en = p1_arb_en ; assign mig_p1_cmd_clk = p1_cmd_clk ; assign mig_p1_cmd_en = p1_cmd_en ; assign mig_p1_cmd_ra = p1_cmd_ra ; assign mig_p1_cmd_ba = p1_cmd_ba ; assign mig_p1_cmd_ca = p1_cmd_ca ; assign mig_p1_cmd_instr = p1_cmd_instr; assign mig_p1_cmd_bl = {(p1_cmd_instr[2] | p1_cmd_bl[5]),p1_cmd_bl[4:0]} ; assign p1_cmd_empty = mig_p1_cmd_empty; assign p1_cmd_full = mig_p1_cmd_full ; end else begin assign mig_p1_arb_en = 'b0; assign mig_p1_cmd_clk = 'b0; assign mig_p1_cmd_en = 'b0; assign mig_p1_cmd_ra = 'b0; assign mig_p1_cmd_ba = 'b0; assign mig_p1_cmd_ca = 'b0; assign mig_p1_cmd_instr = 'b0; assign mig_p1_cmd_bl = 'b0; assign p1_cmd_empty = 'b0; assign p1_cmd_full = 'b0; end if (C_PORT_ENABLE[2] == 1'b1) begin assign mig_p2_arb_en = p2_arb_en ; assign mig_p2_cmd_clk = p2_cmd_clk ; assign mig_p2_cmd_en = p2_cmd_en ; assign mig_p2_cmd_ra = p2_cmd_ra ; assign mig_p2_cmd_ba = p2_cmd_ba ; assign mig_p2_cmd_ca = p2_cmd_ca ; assign mig_p2_cmd_instr = p2_cmd_instr; assign mig_p2_cmd_bl = {(p2_cmd_instr[2] | p2_cmd_bl[5]),p2_cmd_bl[4:0]} ; assign p2_cmd_empty = mig_p2_cmd_empty; assign p2_cmd_full = mig_p2_cmd_full ; end else begin assign mig_p2_arb_en = 'b0; assign mig_p2_cmd_clk = 'b0; assign mig_p2_cmd_en = 'b0; assign mig_p2_cmd_ra = 'b0; assign mig_p2_cmd_ba = 'b0; assign mig_p2_cmd_ca = 'b0; assign mig_p2_cmd_instr = 'b0; assign mig_p2_cmd_bl = 'b0; assign p2_cmd_empty = 'b0; assign p2_cmd_full = 'b0; end if (C_PORT_ENABLE[3] == 1'b1) begin assign mig_p3_arb_en = p3_arb_en ; assign mig_p3_cmd_clk = p3_cmd_clk ; assign mig_p3_cmd_en = p3_cmd_en ; assign mig_p3_cmd_ra = p3_cmd_ra ; assign mig_p3_cmd_ba = p3_cmd_ba ; assign mig_p3_cmd_ca = p3_cmd_ca ; assign mig_p3_cmd_instr = p3_cmd_instr; assign mig_p3_cmd_bl = {(p3_cmd_instr[2] | p3_cmd_bl[5]),p3_cmd_bl[4:0]} ; assign p3_cmd_empty = mig_p3_cmd_empty; assign p3_cmd_full = mig_p3_cmd_full ; end else begin assign mig_p3_arb_en = 'b0; assign mig_p3_cmd_clk = 'b0; assign mig_p3_cmd_en = 'b0; assign mig_p3_cmd_ra = 'b0; assign mig_p3_cmd_ba = 'b0; assign mig_p3_cmd_ca = 'b0; assign mig_p3_cmd_instr = 'b0; assign mig_p3_cmd_bl = 'b0; assign p3_cmd_empty = 'b0; assign p3_cmd_full = 'b0; end if (C_PORT_ENABLE[4] == 1'b1) begin assign mig_p4_arb_en = p4_arb_en ; assign mig_p4_cmd_clk = p4_cmd_clk ; assign mig_p4_cmd_en = p4_cmd_en ; assign mig_p4_cmd_ra = p4_cmd_ra ; assign mig_p4_cmd_ba = p4_cmd_ba ; assign mig_p4_cmd_ca = p4_cmd_ca ; assign mig_p4_cmd_instr = p4_cmd_instr; assign mig_p4_cmd_bl = {(p4_cmd_instr[2] | p4_cmd_bl[5]),p4_cmd_bl[4:0]} ; assign p4_cmd_empty = mig_p4_cmd_empty; assign p4_cmd_full = mig_p4_cmd_full ; end else begin assign mig_p4_arb_en = 'b0; assign mig_p4_cmd_clk = 'b0; assign mig_p4_cmd_en = 'b0; assign mig_p4_cmd_ra = 'b0; assign mig_p4_cmd_ba = 'b0; assign mig_p4_cmd_ca = 'b0; assign mig_p4_cmd_instr = 'b0; assign mig_p4_cmd_bl = 'b0; assign p4_cmd_empty = 'b0; assign p4_cmd_full = 'b0; end if (C_PORT_ENABLE[5] == 1'b1) begin assign mig_p5_arb_en = p5_arb_en ; assign mig_p5_cmd_clk = p5_cmd_clk ; assign mig_p5_cmd_en = p5_cmd_en ; assign mig_p5_cmd_ra = p5_cmd_ra ; assign mig_p5_cmd_ba = p5_cmd_ba ; assign mig_p5_cmd_ca = p5_cmd_ca ; assign mig_p5_cmd_instr = p5_cmd_instr; assign mig_p5_cmd_bl = {(p5_cmd_instr[2] | p5_cmd_bl[5]),p5_cmd_bl[4:0]} ; assign p5_cmd_empty = mig_p5_cmd_empty; assign p5_cmd_full = mig_p5_cmd_full ; end else begin assign mig_p5_arb_en = 'b0; assign mig_p5_cmd_clk = 'b0; assign mig_p5_cmd_en = 'b0; assign mig_p5_cmd_ra = 'b0; assign mig_p5_cmd_ba = 'b0; assign mig_p5_cmd_ca = 'b0; assign mig_p5_cmd_instr = 'b0; assign mig_p5_cmd_bl = 'b0; assign p5_cmd_empty = 'b0; assign p5_cmd_full = 'b0; end // Inputs from Application User Port // Port 0 if (C_PORT_ENABLE[0] == 1'b1) begin assign mig_p0_wr_clk = p0_wr_clk; assign mig_p0_rd_clk = p0_rd_clk; assign mig_p0_wr_en = p0_wr_en; assign mig_p0_rd_en = p0_rd_en; assign mig_p0_wr_mask = p0_wr_mask[3:0]; assign mig_p0_wr_data = p0_wr_data[31:0]; assign p0_rd_data = mig_p0_rd_data; assign p0_rd_full = mig_p0_rd_full; assign p0_rd_empty = mig_p0_rd_empty; assign p0_rd_error = mig_p0_rd_error; assign p0_wr_error = mig_p0_wr_error; assign p0_rd_overflow = mig_p0_rd_overflow; assign p0_wr_underrun = mig_p0_wr_underrun; assign p0_wr_empty = mig_p0_wr_empty; assign p0_wr_full = mig_p0_wr_full; assign p0_wr_count = mig_p0_wr_count; assign p0_rd_count = mig_p0_rd_count ; end else begin assign mig_p0_wr_clk = 'b0; assign mig_p0_rd_clk = 'b0; assign mig_p0_wr_en = 'b0; assign mig_p0_rd_en = 'b0; assign mig_p0_wr_mask = 'b0; assign mig_p0_wr_data = 'b0; assign p0_rd_data = 'b0; assign p0_rd_full = 'b0; assign p0_rd_empty = 'b0; assign p0_rd_error = 'b0; assign p0_wr_error = 'b0; assign p0_rd_overflow = 'b0; assign p0_wr_underrun = 'b0; assign p0_wr_empty = 'b0; assign p0_wr_full = 'b0; assign p0_wr_count = 'b0; assign p0_rd_count = 'b0; end // Port 1 if (C_PORT_ENABLE[1] == 1'b1) begin assign mig_p1_wr_clk = p1_wr_clk; assign mig_p1_rd_clk = p1_rd_clk; assign mig_p1_wr_en = p1_wr_en; assign mig_p1_wr_mask = p1_wr_mask[3:0]; assign mig_p1_wr_data = p1_wr_data[31:0]; assign mig_p1_rd_en = p1_rd_en; assign p1_rd_data = mig_p1_rd_data; assign p1_rd_empty = mig_p1_rd_empty; assign p1_rd_full = mig_p1_rd_full; assign p1_rd_error = mig_p1_rd_error; assign p1_wr_error = mig_p1_wr_error; assign p1_rd_overflow = mig_p1_rd_overflow; assign p1_wr_underrun = mig_p1_wr_underrun; assign p1_wr_empty = mig_p1_wr_empty; assign p1_wr_full = mig_p1_wr_full; assign p1_wr_count = mig_p1_wr_count; assign p1_rd_count = mig_p1_rd_count ; end else begin assign mig_p1_wr_clk = 'b0; assign mig_p1_rd_clk = 'b0; assign mig_p1_wr_en = 'b0; assign mig_p1_wr_mask = 'b0; assign mig_p1_wr_data = 'b0; assign mig_p1_rd_en = 'b0; assign p1_rd_data = 'b0; assign p1_rd_empty = 'b0; assign p1_rd_full = 'b0; assign p1_rd_error = 'b0; assign p1_wr_error = 'b0; assign p1_rd_overflow = 'b0; assign p1_wr_underrun = 'b0; assign p1_wr_empty = 'b0; assign p1_wr_full = 'b0; assign p1_wr_count = 'b0; assign p1_rd_count = 'b0; end // whenever PORT 2 is in Write mode if(C_PORT_CONFIG[183:160] == "B32" && C_PORT_CONFIG[119:96] == "W32") begin : u_config1_2W if (C_PORT_ENABLE[2] == 1'b1) begin assign mig_p2_clk = p2_wr_clk; assign mig_p2_wr_data = p2_wr_data[31:0]; assign mig_p2_wr_mask = p2_wr_mask[3:0]; assign mig_p2_en = p2_wr_en; // this signal will not shown up if the port 5 is for read dir assign p2_wr_error = mig_p2_error; assign p2_wr_full = mig_p2_full; assign p2_wr_empty = mig_p2_empty; assign p2_wr_underrun = mig_p2_underrun; assign p2_wr_count = mig_p2_count ; // wr port end else begin assign mig_p2_clk = 'b0; assign mig_p2_wr_data = 'b0; assign mig_p2_wr_mask = 'b0; assign mig_p2_en = 'b0; assign p2_wr_error = 'b0; assign p2_wr_full = 'b0; assign p2_wr_empty = 'b0; assign p2_wr_underrun = 'b0; assign p2_wr_count = 'b0; end assign p2_rd_data = 'b0; assign p2_rd_overflow = 'b0; assign p2_rd_error = 'b0; assign p2_rd_full = 'b0; assign p2_rd_empty = 'b0; assign p2_rd_count = 'b0; // assign p2_rd_error = 'b0; end else if(C_PORT_CONFIG[183:160] == "B32" && C_PORT_CONFIG[119:96] == "R32") begin : u_config1_2R if (C_PORT_ENABLE[2] == 1'b1) begin assign mig_p2_clk = p2_rd_clk; assign p2_rd_data = mig_p2_rd_data; assign mig_p2_en = p2_rd_en; assign p2_rd_overflow = mig_p2_overflow; assign p2_rd_error = mig_p2_error; assign p2_rd_full = mig_p2_full; assign p2_rd_empty = mig_p2_empty; assign p2_rd_count = mig_p2_count ; // wr port end else begin assign mig_p2_clk = 'b0; assign p2_rd_data = 'b0; assign mig_p2_en = 'b0; assign p2_rd_overflow = 'b0; assign p2_rd_error = 'b0; assign p2_rd_full = 'b0; assign p2_rd_empty = 'b0; assign p2_rd_count = 'b0; end assign mig_p2_wr_data = 'b0; assign mig_p2_wr_mask = 'b0; assign p2_wr_error = 'b0; assign p2_wr_full = 'b0; assign p2_wr_empty = 'b0; assign p2_wr_underrun = 'b0; assign p2_wr_count = 'b0; end if(C_PORT_CONFIG[183:160] == "B32" && C_PORT_CONFIG[87:64] == "W32") begin : u_config1_3W // whenever PORT 3 is in Write mode if (C_PORT_ENABLE[3] == 1'b1) begin assign mig_p3_clk = p3_wr_clk; assign mig_p3_wr_data = p3_wr_data[31:0]; assign mig_p3_wr_mask = p3_wr_mask[3:0]; assign mig_p3_en = p3_wr_en; assign p3_wr_full = mig_p3_full; assign p3_wr_empty = mig_p3_empty; assign p3_wr_underrun = mig_p3_underrun; assign p3_wr_count = mig_p3_count ; // wr port assign p3_wr_error = mig_p3_error; end else begin assign mig_p3_clk = 'b0; assign mig_p3_wr_data = 'b0; assign mig_p3_wr_mask = 'b0; assign mig_p3_en = 'b0; assign p3_wr_full = 'b0; assign p3_wr_empty = 'b0; assign p3_wr_underrun = 'b0; assign p3_wr_count = 'b0; assign p3_wr_error = 'b0; end assign p3_rd_overflow = 'b0; assign p3_rd_error = 'b0; assign p3_rd_full = 'b0; assign p3_rd_empty = 'b0; assign p3_rd_count = 'b0; assign p3_rd_data = 'b0; end else if(C_PORT_CONFIG[183:160] == "B32" && C_PORT_CONFIG[87:64] == "R32") begin : u_config1_3R if (C_PORT_ENABLE[3] == 1'b1) begin assign mig_p3_clk = p3_rd_clk; assign p3_rd_data = mig_p3_rd_data; assign mig_p3_en = p3_rd_en; // this signal will not shown up if the port 5 is for write dir assign p3_rd_overflow = mig_p3_overflow; assign p3_rd_error = mig_p3_error; assign p3_rd_full = mig_p3_full; assign p3_rd_empty = mig_p3_empty; assign p3_rd_count = mig_p3_count ; // wr port end else begin assign mig_p3_clk = 'b0; assign mig_p3_en = 'b0; assign p3_rd_overflow = 'b0; assign p3_rd_full = 'b0; assign p3_rd_empty = 'b0; assign p3_rd_count = 'b0; assign p3_rd_error = 'b0; assign p3_rd_data = 'b0; end assign p3_wr_full = 'b0; assign p3_wr_empty = 'b0; assign p3_wr_underrun = 'b0; assign p3_wr_count = 'b0; assign p3_wr_error = 'b0; assign mig_p3_wr_data = 'b0; assign mig_p3_wr_mask = 'b0; end if(C_PORT_CONFIG[183:160] == "B32" && C_PORT_CONFIG[55:32] == "W32") begin : u_config1_4W // whenever PORT 4 is in Write mode if (C_PORT_ENABLE[4] == 1'b1) begin assign mig_p4_clk = p4_wr_clk; assign mig_p4_wr_data = p4_wr_data[31:0]; assign mig_p4_wr_mask = p4_wr_mask[3:0]; assign mig_p4_en = p4_wr_en; // this signal will not shown up if the port 5 is for read dir assign p4_wr_full = mig_p4_full; assign p4_wr_empty = mig_p4_empty; assign p4_wr_underrun = mig_p4_underrun; assign p4_wr_count = mig_p4_count ; // wr port assign p4_wr_error = mig_p4_error; end else begin assign mig_p4_clk = 'b0; assign mig_p4_wr_data = 'b0; assign mig_p4_wr_mask = 'b0; assign mig_p4_en = 'b0; assign p4_wr_full = 'b0; assign p4_wr_empty = 'b0; assign p4_wr_underrun = 'b0; assign p4_wr_count = 'b0; assign p4_wr_error = 'b0; end assign p4_rd_overflow = 'b0; assign p4_rd_error = 'b0; assign p4_rd_full = 'b0; assign p4_rd_empty = 'b0; assign p4_rd_count = 'b0; assign p4_rd_data = 'b0; end else if(C_PORT_CONFIG[183:160] == "B32" && C_PORT_CONFIG[55:32] == "R32") begin : u_config1_4R if (C_PORT_ENABLE[4] == 1'b1) begin assign mig_p4_clk = p4_rd_clk; assign p4_rd_data = mig_p4_rd_data; assign mig_p4_en = p4_rd_en; // this signal will not shown up if the port 5 is for write dir assign p4_rd_overflow = mig_p4_overflow; assign p4_rd_error = mig_p4_error; assign p4_rd_full = mig_p4_full; assign p4_rd_empty = mig_p4_empty; assign p4_rd_count = mig_p4_count ; // wr port end else begin assign mig_p4_clk = 'b0; assign p4_rd_data = 'b0; assign mig_p4_en = 'b0; assign p4_rd_overflow = 'b0; assign p4_rd_error = 'b0; assign p4_rd_full = 'b0; assign p4_rd_empty = 'b0; assign p4_rd_count = 'b0; end assign p4_wr_full = 'b0; assign p4_wr_empty = 'b0; assign p4_wr_underrun = 'b0; assign p4_wr_count = 'b0; assign p4_wr_error = 'b0; assign mig_p4_wr_data = 'b0; assign mig_p4_wr_mask = 'b0; end if(C_PORT_CONFIG[183:160] == "B32" && C_PORT_CONFIG[23:0] == "W32") begin : u_config1_5W // whenever PORT 5 is in Write mode if (C_PORT_ENABLE[5] == 1'b1) begin assign mig_p5_clk = p5_wr_clk; assign mig_p5_wr_data = p5_wr_data[31:0]; assign mig_p5_wr_mask = p5_wr_mask[3:0]; assign mig_p5_en = p5_wr_en; assign p5_wr_full = mig_p5_full; assign p5_wr_empty = mig_p5_empty; assign p5_wr_underrun = mig_p5_underrun; assign p5_wr_count = mig_p5_count ; assign p5_wr_error = mig_p5_error; end else begin assign mig_p5_clk = 'b0; assign mig_p5_wr_data = 'b0; assign mig_p5_wr_mask = 'b0; assign mig_p5_en = 'b0; assign p5_wr_full = 'b0; assign p5_wr_empty = 'b0; assign p5_wr_underrun = 'b0; assign p5_wr_count = 'b0; assign p5_wr_error = 'b0; end assign p5_rd_data = 'b0; assign p5_rd_overflow = 'b0; assign p5_rd_error = 'b0; assign p5_rd_full = 'b0; assign p5_rd_empty = 'b0; assign p5_rd_count = 'b0; end else if(C_PORT_CONFIG[183:160] == "B32" && C_PORT_CONFIG[23:0] == "R32") begin : u_config1_5R if (C_PORT_ENABLE[5] == 1'b1) begin assign mig_p5_clk = p5_rd_clk; assign p5_rd_data = mig_p5_rd_data; assign mig_p5_en = p5_rd_en; assign p5_rd_overflow = mig_p5_overflow; assign p5_rd_error = mig_p5_error; assign p5_rd_full = mig_p5_full; assign p5_rd_empty = mig_p5_empty; assign p5_rd_count = mig_p5_count ; end else begin assign mig_p5_clk = 'b0; assign p5_rd_data = 'b0; assign mig_p5_en = 'b0; assign p5_rd_overflow = 'b0; assign p5_rd_error = 'b0; assign p5_rd_full = 'b0; assign p5_rd_empty = 'b0; assign p5_rd_count = 'b0; end assign p5_wr_full = 'b0; assign p5_wr_empty = 'b0; assign p5_wr_underrun = 'b0; assign p5_wr_count = 'b0; assign p5_wr_error = 'b0; assign mig_p5_wr_data = 'b0; assign mig_p5_wr_mask = 'b0; end end else if(C_PORT_CONFIG == "B32_B32_B32_B32" ) begin : u_config_2 // Inputs from Application CMD Port // ************* need to hook up rd /wr error outputs if (C_PORT_ENABLE[0] == 1'b1) begin // command port signals assign mig_p0_arb_en = p0_arb_en ; assign mig_p0_cmd_clk = p0_cmd_clk ; assign mig_p0_cmd_en = p0_cmd_en ; assign mig_p0_cmd_ra = p0_cmd_ra ; assign mig_p0_cmd_ba = p0_cmd_ba ; assign mig_p0_cmd_ca = p0_cmd_ca ; assign mig_p0_cmd_instr = p0_cmd_instr; assign mig_p0_cmd_bl = {(p0_cmd_instr[2] | p0_cmd_bl[5]),p0_cmd_bl[4:0]} ; // Data port signals assign mig_p0_rd_en = p0_rd_en; assign mig_p0_wr_clk = p0_wr_clk; assign mig_p0_rd_clk = p0_rd_clk; assign mig_p0_wr_en = p0_wr_en; assign mig_p0_wr_data = p0_wr_data[31:0]; assign mig_p0_wr_mask = p0_wr_mask[3:0]; assign p0_wr_count = mig_p0_wr_count; assign p0_rd_count = mig_p0_rd_count ; end else begin assign mig_p0_arb_en = 'b0; assign mig_p0_cmd_clk = 'b0; assign mig_p0_cmd_en = 'b0; assign mig_p0_cmd_ra = 'b0; assign mig_p0_cmd_ba = 'b0; assign mig_p0_cmd_ca = 'b0; assign mig_p0_cmd_instr = 'b0; assign mig_p0_cmd_bl = 'b0; assign mig_p0_rd_en = 'b0; assign mig_p0_wr_clk = 'b0; assign mig_p0_rd_clk = 'b0; assign mig_p0_wr_en = 'b0; assign mig_p0_wr_data = 'b0; assign mig_p0_wr_mask = 'b0; assign p0_wr_count = 'b0; assign p0_rd_count = 'b0; end assign p0_cmd_empty = mig_p0_cmd_empty ; assign p0_cmd_full = mig_p0_cmd_full ; if (C_PORT_ENABLE[1] == 1'b1) begin // command port signals assign mig_p1_arb_en = p1_arb_en ; assign mig_p1_cmd_clk = p1_cmd_clk ; assign mig_p1_cmd_en = p1_cmd_en ; assign mig_p1_cmd_ra = p1_cmd_ra ; assign mig_p1_cmd_ba = p1_cmd_ba ; assign mig_p1_cmd_ca = p1_cmd_ca ; assign mig_p1_cmd_instr = p1_cmd_instr; assign mig_p1_cmd_bl = {(p1_cmd_instr[2] | p1_cmd_bl[5]),p1_cmd_bl[4:0]} ; // Data port signals assign mig_p1_wr_en = p1_wr_en; assign mig_p1_wr_clk = p1_wr_clk; assign mig_p1_rd_en = p1_rd_en; assign mig_p1_wr_data = p1_wr_data[31:0]; assign mig_p1_wr_mask = p1_wr_mask[3:0]; assign mig_p1_rd_clk = p1_rd_clk; assign p1_wr_count = mig_p1_wr_count; assign p1_rd_count = mig_p1_rd_count; end else begin assign mig_p1_arb_en = 'b0; assign mig_p1_cmd_clk = 'b0; assign mig_p1_cmd_en = 'b0; assign mig_p1_cmd_ra = 'b0; assign mig_p1_cmd_ba = 'b0; assign mig_p1_cmd_ca = 'b0; assign mig_p1_cmd_instr = 'b0; assign mig_p1_cmd_bl = 'b0; // Data port signals assign mig_p1_wr_en = 'b0; assign mig_p1_wr_clk = 'b0; assign mig_p1_rd_en = 'b0; assign mig_p1_wr_data = 'b0; assign mig_p1_wr_mask = 'b0; assign mig_p1_rd_clk = 'b0; assign p1_wr_count = 'b0; assign p1_rd_count = 'b0; end assign p1_cmd_empty = mig_p1_cmd_empty ; assign p1_cmd_full = mig_p1_cmd_full ; if (C_PORT_ENABLE[2] == 1'b1) begin //MCB Physical port Logical Port assign mig_p2_arb_en = p2_arb_en ; assign mig_p2_cmd_clk = p2_cmd_clk ; assign mig_p2_cmd_en = p2_cmd_en ; assign mig_p2_cmd_ra = p2_cmd_ra ; assign mig_p2_cmd_ba = p2_cmd_ba ; assign mig_p2_cmd_ca = p2_cmd_ca ; assign mig_p2_cmd_instr = p2_cmd_instr; assign mig_p2_cmd_bl = {(p2_cmd_instr[2] | p2_cmd_bl[5]),p2_cmd_bl[4:0]} ; assign mig_p2_en = p2_rd_en; assign mig_p2_clk = p2_rd_clk; assign mig_p3_en = p2_wr_en; assign mig_p3_clk = p2_wr_clk; assign mig_p3_wr_data = p2_wr_data[31:0]; assign mig_p3_wr_mask = p2_wr_mask[3:0]; assign p2_wr_count = mig_p3_count; assign p2_rd_count = mig_p2_count; end else begin assign mig_p2_arb_en = 'b0; assign mig_p2_cmd_clk = 'b0; assign mig_p2_cmd_en = 'b0; assign mig_p2_cmd_ra = 'b0; assign mig_p2_cmd_ba = 'b0; assign mig_p2_cmd_ca = 'b0; assign mig_p2_cmd_instr = 'b0; assign mig_p2_cmd_bl = 'b0; assign mig_p2_en = 'b0; assign mig_p2_clk = 'b0; assign mig_p3_en = 'b0; assign mig_p3_clk = 'b0; assign mig_p3_wr_data = 'b0; assign mig_p3_wr_mask = 'b0; assign p2_rd_count = 'b0; assign p2_wr_count = 'b0; end assign p2_cmd_empty = mig_p2_cmd_empty ; assign p2_cmd_full = mig_p2_cmd_full ; if (C_PORT_ENABLE[3] == 1'b1) begin //MCB Physical port Logical Port assign mig_p4_arb_en = p3_arb_en ; assign mig_p4_cmd_clk = p3_cmd_clk ; assign mig_p4_cmd_en = p3_cmd_en ; assign mig_p4_cmd_ra = p3_cmd_ra ; assign mig_p4_cmd_ba = p3_cmd_ba ; assign mig_p4_cmd_ca = p3_cmd_ca ; assign mig_p4_cmd_instr = p3_cmd_instr; assign mig_p4_cmd_bl = {(p3_cmd_instr[2] | p3_cmd_bl[5]),p3_cmd_bl[4:0]} ; assign mig_p4_clk = p3_rd_clk; assign mig_p4_en = p3_rd_en; assign mig_p5_clk = p3_wr_clk; assign mig_p5_en = p3_wr_en; assign mig_p5_wr_data = p3_wr_data[31:0]; assign mig_p5_wr_mask = p3_wr_mask[3:0]; assign p3_rd_count = mig_p4_count; assign p3_wr_count = mig_p5_count; end else begin assign mig_p4_arb_en = 'b0; assign mig_p4_cmd_clk = 'b0; assign mig_p4_cmd_en = 'b0; assign mig_p4_cmd_ra = 'b0; assign mig_p4_cmd_ba = 'b0; assign mig_p4_cmd_ca = 'b0; assign mig_p4_cmd_instr = 'b0; assign mig_p4_cmd_bl = 'b0; assign mig_p4_clk = 'b0; assign mig_p4_en = 'b0; assign mig_p5_clk = 'b0; assign mig_p5_en = 'b0; assign mig_p5_wr_data = 'b0; assign mig_p5_wr_mask = 'b0; assign p3_rd_count = 'b0; assign p3_wr_count = 'b0; end assign p3_cmd_empty = mig_p4_cmd_empty ; assign p3_cmd_full = mig_p4_cmd_full ; // outputs to Applications User Port assign p0_rd_data = mig_p0_rd_data; assign p1_rd_data = mig_p1_rd_data; assign p2_rd_data = mig_p2_rd_data; assign p3_rd_data = mig_p4_rd_data; assign p0_rd_empty = mig_p0_rd_empty; assign p1_rd_empty = mig_p1_rd_empty; assign p2_rd_empty = mig_p2_empty; assign p3_rd_empty = mig_p4_empty; assign p0_rd_full = mig_p0_rd_full; assign p1_rd_full = mig_p1_rd_full; assign p2_rd_full = mig_p2_full; assign p3_rd_full = mig_p4_full; assign p0_rd_error = mig_p0_rd_error; assign p1_rd_error = mig_p1_rd_error; assign p2_rd_error = mig_p2_error; assign p3_rd_error = mig_p4_error; assign p0_rd_overflow = mig_p0_rd_overflow; assign p1_rd_overflow = mig_p1_rd_overflow; assign p2_rd_overflow = mig_p2_overflow; assign p3_rd_overflow = mig_p4_overflow; assign p0_wr_underrun = mig_p0_wr_underrun; assign p1_wr_underrun = mig_p1_wr_underrun; assign p2_wr_underrun = mig_p3_underrun; assign p3_wr_underrun = mig_p5_underrun; assign p0_wr_empty = mig_p0_wr_empty; assign p1_wr_empty = mig_p1_wr_empty; assign p2_wr_empty = mig_p3_empty; assign p3_wr_empty = mig_p5_empty; assign p0_wr_full = mig_p0_wr_full; assign p1_wr_full = mig_p1_wr_full; assign p2_wr_full = mig_p3_full; assign p3_wr_full = mig_p5_full; assign p0_wr_error = mig_p0_wr_error; assign p1_wr_error = mig_p1_wr_error; assign p2_wr_error = mig_p3_error; assign p3_wr_error = mig_p5_error; // unused ports signals assign p4_cmd_empty = 1'b0; assign p4_cmd_full = 1'b0; assign mig_p2_wr_mask = 'b0; assign mig_p4_wr_mask = 'b0; assign mig_p2_wr_data = 'b0; assign mig_p4_wr_data = 'b0; assign p5_cmd_empty = 1'b0; assign p5_cmd_full = 1'b0; assign mig_p3_cmd_clk = 1'b0; assign mig_p3_cmd_en = 1'b0; assign mig_p3_cmd_ra = 15'd0; assign mig_p3_cmd_ba = 3'd0; assign mig_p3_cmd_ca = 12'd0; assign mig_p3_cmd_instr = 3'd0; assign mig_p3_cmd_bl = 6'd0; assign mig_p3_arb_en = 1'b0; // physical cmd port 3 is not used in this config assign mig_p5_arb_en = 1'b0; // physical cmd port 3 is not used in this config assign mig_p5_cmd_clk = 1'b0; assign mig_p5_cmd_en = 1'b0; assign mig_p5_cmd_ra = 15'd0; assign mig_p5_cmd_ba = 3'd0; assign mig_p5_cmd_ca = 12'd0; assign mig_p5_cmd_instr = 3'd0; assign mig_p5_cmd_bl = 6'd0; //////////////////////////////////////////////////////////////////////////// ///////////////////////////////////////////////////////////////////////////// //// //// B64_B32_B32 //// ///////////////////////////////////////////////////////////////////////////// //////////////////////////////////////////////////////////////////////////// end else if(C_PORT_CONFIG == "B64_B32_B32" ) begin : u_config_3 // Inputs from Application CMD Port if (C_PORT_ENABLE[0] == 1'b1) begin assign mig_p0_arb_en = p0_arb_en ; assign mig_p0_cmd_clk = p0_cmd_clk ; assign mig_p0_cmd_en = p0_cmd_en ; assign mig_p0_cmd_ra = p0_cmd_ra ; assign mig_p0_cmd_ba = p0_cmd_ba ; assign mig_p0_cmd_ca = p0_cmd_ca ; assign mig_p0_cmd_instr = p0_cmd_instr; assign mig_p0_cmd_bl = {(p0_cmd_instr[2] | p0_cmd_bl[5]),p0_cmd_bl[4:0]} ; assign p0_cmd_empty = mig_p0_cmd_empty ; assign p0_cmd_full = mig_p0_cmd_full ; assign mig_p0_wr_clk = p0_wr_clk; assign mig_p0_rd_clk = p0_rd_clk; assign mig_p1_wr_clk = p0_wr_clk; assign mig_p1_rd_clk = p0_rd_clk; assign mig_p0_wr_en = p0_wr_en & !p0_wr_full; assign mig_p1_wr_en = p0_wr_en & !p0_wr_full; assign mig_p0_wr_data = p0_wr_data[31:0]; assign mig_p0_wr_mask = p0_wr_mask[3:0]; assign mig_p1_wr_data = p0_wr_data[63 : 32]; assign mig_p1_wr_mask = p0_wr_mask[7 : 4]; assign p0_rd_empty = mig_p1_rd_empty; assign p0_rd_data = {mig_p1_rd_data , mig_p0_rd_data}; assign mig_p0_rd_en = p0_rd_en & !p0_rd_empty; assign mig_p1_rd_en = p0_rd_en & !p0_rd_empty; assign p0_wr_count = mig_p1_wr_count; // B64 for port 0, map most significant port to output assign p0_rd_count = mig_p1_rd_count; assign p0_wr_empty = mig_p1_wr_empty; assign p0_wr_error = mig_p1_wr_error | mig_p0_wr_error; assign p0_wr_full = mig_p1_wr_full; assign p0_wr_underrun = mig_p1_wr_underrun | mig_p0_wr_underrun; assign p0_rd_overflow = mig_p1_rd_overflow | mig_p0_rd_overflow; assign p0_rd_error = mig_p1_rd_error | mig_p0_rd_error; assign p0_rd_full = mig_p1_rd_full; end else begin assign mig_p0_arb_en = 'b0; assign mig_p0_cmd_clk = 'b0; assign mig_p0_cmd_en = 'b0; assign mig_p0_cmd_ra = 'b0; assign mig_p0_cmd_ba = 'b0; assign mig_p0_cmd_ca = 'b0; assign mig_p0_cmd_instr = 'b0; assign mig_p0_cmd_bl = 'b0; assign p0_cmd_empty = 'b0; assign p0_cmd_full = 'b0; assign mig_p0_wr_clk = 'b0; assign mig_p0_rd_clk = 'b0; assign mig_p1_wr_clk = 'b0; assign mig_p1_rd_clk = 'b0; assign mig_p0_wr_en = 'b0; assign mig_p1_wr_en = 'b0; assign mig_p0_wr_data = 'b0; assign mig_p0_wr_mask = 'b0; assign mig_p1_wr_data = 'b0; assign mig_p1_wr_mask = 'b0; assign p0_rd_empty = 'b0; assign p0_rd_data = 'b0; assign mig_p0_rd_en = 'b0; assign mig_p1_rd_en = 'b0; assign p0_wr_count = 'b0; assign p0_rd_count = 'b0; assign p0_wr_empty = 'b0; assign p0_wr_error = 'b0; assign p0_wr_full = 'b0; assign p0_wr_underrun = 'b0; assign p0_rd_overflow = 'b0; assign p0_rd_error = 'b0; assign p0_rd_full = 'b0; end if (C_PORT_ENABLE[1] == 1'b1) begin assign mig_p2_arb_en = p1_arb_en ; assign mig_p2_cmd_clk = p1_cmd_clk ; assign mig_p2_cmd_en = p1_cmd_en ; assign mig_p2_cmd_ra = p1_cmd_ra ; assign mig_p2_cmd_ba = p1_cmd_ba ; assign mig_p2_cmd_ca = p1_cmd_ca ; assign mig_p2_cmd_instr = p1_cmd_instr; assign mig_p2_cmd_bl = {(p1_cmd_instr[2] | p1_cmd_bl[5]),p1_cmd_bl[4:0]} ; assign p1_cmd_empty = mig_p2_cmd_empty; assign p1_cmd_full = mig_p2_cmd_full; assign mig_p2_clk = p1_rd_clk; assign mig_p3_clk = p1_wr_clk; assign mig_p3_en = p1_wr_en; assign mig_p3_wr_data = p1_wr_data[31:0]; assign mig_p3_wr_mask = p1_wr_mask[3:0]; assign mig_p2_en = p1_rd_en; assign p1_rd_data = mig_p2_rd_data; assign p1_wr_count = mig_p3_count; assign p1_rd_count = mig_p2_count; assign p1_wr_empty = mig_p3_empty; assign p1_wr_error = mig_p3_error; assign p1_wr_full = mig_p3_full; assign p1_wr_underrun = mig_p3_underrun; assign p1_rd_overflow = mig_p2_overflow; assign p1_rd_error = mig_p2_error; assign p1_rd_full = mig_p2_full; assign p1_rd_empty = mig_p2_empty; end else begin assign mig_p2_arb_en = 'b0; assign mig_p2_cmd_clk = 'b0; assign mig_p2_cmd_en = 'b0; assign mig_p2_cmd_ra = 'b0; assign mig_p2_cmd_ba = 'b0; assign mig_p2_cmd_ca = 'b0; assign mig_p2_cmd_instr = 'b0; assign mig_p2_cmd_bl = 'b0; assign p1_cmd_empty = 'b0; assign p1_cmd_full = 'b0; assign mig_p3_en = 'b0; assign mig_p3_wr_data = 'b0; assign mig_p3_wr_mask = 'b0; assign mig_p2_en = 'b0; assign mig_p2_clk = 'b0; assign mig_p3_clk = 'b0; assign p1_rd_data = 'b0; assign p1_wr_count = 'b0; assign p1_rd_count = 'b0; assign p1_wr_empty = 'b0; assign p1_wr_error = 'b0; assign p1_wr_full = 'b0; assign p1_wr_underrun = 'b0; assign p1_rd_overflow = 'b0; assign p1_rd_error = 'b0; assign p1_rd_full = 'b0; assign p1_rd_empty = 'b0; end if (C_PORT_ENABLE[2] == 1'b1) begin assign mig_p4_arb_en = p2_arb_en ; assign mig_p4_cmd_clk = p2_cmd_clk ; assign mig_p4_cmd_en = p2_cmd_en ; assign mig_p4_cmd_ra = p2_cmd_ra ; assign mig_p4_cmd_ba = p2_cmd_ba ; assign mig_p4_cmd_ca = p2_cmd_ca ; assign mig_p4_cmd_instr = p2_cmd_instr; assign mig_p4_cmd_bl = {(p2_cmd_instr[2] | p2_cmd_bl[5]),p2_cmd_bl[4:0]} ; assign p2_cmd_empty = mig_p4_cmd_empty ; assign p2_cmd_full = mig_p4_cmd_full ; assign mig_p5_en = p2_wr_en; assign mig_p5_wr_data = p2_wr_data[31:0]; assign mig_p5_wr_mask = p2_wr_mask[3:0]; assign mig_p4_en = p2_rd_en; assign mig_p4_clk = p2_rd_clk; assign mig_p5_clk = p2_wr_clk; assign p2_rd_data = mig_p4_rd_data; assign p2_wr_count = mig_p5_count; assign p2_rd_count = mig_p4_count; assign p2_wr_empty = mig_p5_empty; assign p2_wr_full = mig_p5_full; assign p2_wr_error = mig_p5_error; assign p2_wr_underrun = mig_p5_underrun; assign p2_rd_overflow = mig_p4_overflow; assign p2_rd_error = mig_p4_error; assign p2_rd_full = mig_p4_full; assign p2_rd_empty = mig_p4_empty; end else begin assign mig_p4_arb_en = 'b0; assign mig_p4_cmd_clk = 'b0; assign mig_p4_cmd_en = 'b0; assign mig_p4_cmd_ra = 'b0; assign mig_p4_cmd_ba = 'b0; assign mig_p4_cmd_ca = 'b0; assign mig_p4_cmd_instr = 'b0; assign mig_p4_cmd_bl = 'b0; assign p2_cmd_empty = 'b0; assign p2_cmd_full = 'b0; assign mig_p5_en = 'b0; assign mig_p5_wr_data = 'b0; assign mig_p5_wr_mask = 'b0; assign mig_p4_en = 'b0; assign mig_p4_clk = 'b0; assign mig_p5_clk = 'b0; assign p2_rd_data = 'b0; assign p2_wr_count = 'b0; assign p2_rd_count = 'b0; assign p2_wr_empty = 'b0; assign p2_wr_full = 'b0; assign p2_wr_error = 'b0; assign p2_wr_underrun = 'b0; assign p2_rd_overflow = 'b0; assign p2_rd_error = 'b0; assign p2_rd_full = 'b0; assign p2_rd_empty = 'b0; end // MCB's port 1,3,5 is not used in this Config mode assign mig_p1_arb_en = 1'b0; assign mig_p1_cmd_clk = 1'b0; assign mig_p1_cmd_en = 1'b0; assign mig_p1_cmd_ra = 15'd0; assign mig_p1_cmd_ba = 3'd0; assign mig_p1_cmd_ca = 12'd0; assign mig_p1_cmd_instr = 3'd0; assign mig_p1_cmd_bl = 6'd0; assign mig_p3_arb_en = 1'b0; assign mig_p3_cmd_clk = 1'b0; assign mig_p3_cmd_en = 1'b0; assign mig_p3_cmd_ra = 15'd0; assign mig_p3_cmd_ba = 3'd0; assign mig_p3_cmd_ca = 12'd0; assign mig_p3_cmd_instr = 3'd0; assign mig_p3_cmd_bl = 6'd0; assign mig_p5_arb_en = 1'b0; assign mig_p5_cmd_clk = 1'b0; assign mig_p5_cmd_en = 1'b0; assign mig_p5_cmd_ra = 15'd0; assign mig_p5_cmd_ba = 3'd0; assign mig_p5_cmd_ca = 12'd0; assign mig_p5_cmd_instr = 3'd0; assign mig_p5_cmd_bl = 6'd0; end else if(C_PORT_CONFIG == "B64_B64" ) begin : u_config_4 // Inputs from Application CMD Port if (C_PORT_ENABLE[0] == 1'b1) begin assign mig_p0_arb_en = p0_arb_en ; assign mig_p1_arb_en = p0_arb_en ; assign mig_p0_cmd_clk = p0_cmd_clk ; assign mig_p0_cmd_en = p0_cmd_en ; assign mig_p0_cmd_ra = p0_cmd_ra ; assign mig_p0_cmd_ba = p0_cmd_ba ; assign mig_p0_cmd_ca = p0_cmd_ca ; assign mig_p0_cmd_instr = p0_cmd_instr; assign mig_p0_cmd_bl = {(p0_cmd_instr[2] | p0_cmd_bl[5]),p0_cmd_bl[4:0]} ; assign mig_p0_wr_clk = p0_wr_clk; assign mig_p0_rd_clk = p0_rd_clk; assign mig_p1_wr_clk = p0_wr_clk; assign mig_p1_rd_clk = p0_rd_clk; assign mig_p0_wr_en = p0_wr_en & !p0_wr_full; assign mig_p0_wr_data = p0_wr_data[31:0]; assign mig_p0_wr_mask = p0_wr_mask[3:0]; assign mig_p1_wr_data = p0_wr_data[63 : 32]; assign mig_p1_wr_mask = p0_wr_mask[7 : 4]; assign mig_p1_wr_en = p0_wr_en & !p0_wr_full; assign mig_p0_rd_en = p0_rd_en & !p0_rd_empty; assign mig_p1_rd_en = p0_rd_en & !p0_rd_empty; assign p0_rd_data = {mig_p1_rd_data , mig_p0_rd_data}; assign p0_cmd_empty = mig_p0_cmd_empty ; assign p0_cmd_full = mig_p0_cmd_full ; assign p0_wr_empty = mig_p1_wr_empty; assign p0_wr_full = mig_p1_wr_full; assign p0_wr_error = mig_p1_wr_error | mig_p0_wr_error; assign p0_wr_count = mig_p1_wr_count; assign p0_rd_count = mig_p1_rd_count; assign p0_wr_underrun = mig_p1_wr_underrun | mig_p0_wr_underrun; assign p0_rd_overflow = mig_p1_rd_overflow | mig_p0_rd_overflow; assign p0_rd_error = mig_p1_rd_error | mig_p0_rd_error; assign p0_rd_full = mig_p1_rd_full; assign p0_rd_empty = mig_p1_rd_empty; end else begin assign mig_p0_arb_en = 'b0; assign mig_p0_cmd_clk = 'b0; assign mig_p0_cmd_en = 'b0; assign mig_p0_cmd_ra = 'b0; assign mig_p0_cmd_ba = 'b0; assign mig_p0_cmd_ca = 'b0; assign mig_p0_cmd_instr = 'b0; assign mig_p0_cmd_bl = 'b0; assign mig_p0_wr_clk = 'b0; assign mig_p0_rd_clk = 'b0; assign mig_p1_wr_clk = 'b0; assign mig_p1_rd_clk = 'b0; assign mig_p0_wr_en = 'b0; assign mig_p1_wr_en = 'b0; assign mig_p0_wr_data = 'b0; assign mig_p0_wr_mask = 'b0; assign mig_p1_wr_data = 'b0; assign mig_p1_wr_mask = 'b0; // assign mig_p1_wr_en = 'b0; assign mig_p0_rd_en = 'b0; assign mig_p1_rd_en = 'b0; assign p0_rd_data = 'b0; assign p0_cmd_empty = 'b0; assign p0_cmd_full = 'b0; assign p0_wr_empty = 'b0; assign p0_wr_full = 'b0; assign p0_wr_error = 'b0; assign p0_wr_count = 'b0; assign p0_rd_count = 'b0; assign p0_wr_underrun = 'b0; assign p0_rd_overflow = 'b0; assign p0_rd_error = 'b0; assign p0_rd_full = 'b0; assign p0_rd_empty = 'b0; end if (C_PORT_ENABLE[1] == 1'b1) begin assign mig_p2_arb_en = p1_arb_en ; assign mig_p2_cmd_clk = p1_cmd_clk ; assign mig_p2_cmd_en = p1_cmd_en ; assign mig_p2_cmd_ra = p1_cmd_ra ; assign mig_p2_cmd_ba = p1_cmd_ba ; assign mig_p2_cmd_ca = p1_cmd_ca ; assign mig_p2_cmd_instr = p1_cmd_instr; assign mig_p2_cmd_bl = {(p1_cmd_instr[2] | p1_cmd_bl[5]),p1_cmd_bl[4:0]} ; assign mig_p2_clk = p1_rd_clk; assign mig_p3_clk = p1_wr_clk; assign mig_p4_clk = p1_rd_clk; assign mig_p5_clk = p1_wr_clk; assign mig_p3_en = p1_wr_en & !p1_wr_full; assign mig_p5_en = p1_wr_en & !p1_wr_full; assign mig_p3_wr_data = p1_wr_data[31:0]; assign mig_p3_wr_mask = p1_wr_mask[3:0]; assign mig_p5_wr_data = p1_wr_data[63 : 32]; assign mig_p5_wr_mask = p1_wr_mask[7 : 4]; assign mig_p2_en = p1_rd_en & !p1_rd_empty; assign mig_p4_en = p1_rd_en & !p1_rd_empty; assign p1_cmd_empty = mig_p2_cmd_empty ; assign p1_cmd_full = mig_p2_cmd_full ; assign p1_wr_count = mig_p5_count; assign p1_rd_count = mig_p4_count; assign p1_wr_full = mig_p5_full; assign p1_wr_error = mig_p5_error | mig_p5_error; assign p1_wr_empty = mig_p5_empty; assign p1_wr_underrun = mig_p3_underrun | mig_p5_underrun; assign p1_rd_overflow = mig_p4_overflow; assign p1_rd_error = mig_p4_error; assign p1_rd_full = mig_p4_full; assign p1_rd_empty = mig_p4_empty; assign p1_rd_data = {mig_p4_rd_data , mig_p2_rd_data}; end else begin assign mig_p2_arb_en = 'b0; // assign mig_p3_arb_en = 'b0; // assign mig_p4_arb_en = 'b0; // assign mig_p5_arb_en = 'b0; assign mig_p2_cmd_clk = 'b0; assign mig_p2_cmd_en = 'b0; assign mig_p2_cmd_ra = 'b0; assign mig_p2_cmd_ba = 'b0; assign mig_p2_cmd_ca = 'b0; assign mig_p2_cmd_instr = 'b0; assign mig_p2_cmd_bl = 'b0; assign mig_p2_clk = 'b0; assign mig_p3_clk = 'b0; assign mig_p4_clk = 'b0; assign mig_p5_clk = 'b0; assign mig_p3_en = 'b0; assign mig_p5_en = 'b0; assign mig_p3_wr_data = 'b0; assign mig_p3_wr_mask = 'b0; assign mig_p5_wr_data = 'b0; assign mig_p5_wr_mask = 'b0; assign mig_p2_en = 'b0; assign mig_p4_en = 'b0; assign p1_cmd_empty = 'b0; assign p1_cmd_full = 'b0; assign p1_wr_count = 'b0; assign p1_rd_count = 'b0; assign p1_wr_full = 'b0; assign p1_wr_error = 'b0; assign p1_wr_empty = 'b0; assign p1_wr_underrun = 'b0; assign p1_rd_overflow = 'b0; assign p1_rd_error = 'b0; assign p1_rd_full = 'b0; assign p1_rd_empty = 'b0; assign p1_rd_data = 'b0; end // unused MCB's signals in this configuration assign mig_p3_arb_en = 1'b0; assign mig_p4_arb_en = 1'b0; assign mig_p5_arb_en = 1'b0; assign mig_p3_cmd_clk = 1'b0; assign mig_p3_cmd_en = 1'b0; assign mig_p3_cmd_ra = 15'd0; assign mig_p3_cmd_ba = 3'd0; assign mig_p3_cmd_ca = 12'd0; assign mig_p3_cmd_instr = 3'd0; assign mig_p4_cmd_clk = 1'b0; assign mig_p4_cmd_en = 1'b0; assign mig_p4_cmd_ra = 15'd0; assign mig_p4_cmd_ba = 3'd0; assign mig_p4_cmd_ca = 12'd0; assign mig_p4_cmd_instr = 3'd0; assign mig_p4_cmd_bl = 6'd0; assign mig_p5_cmd_clk = 1'b0; assign mig_p5_cmd_en = 1'b0; assign mig_p5_cmd_ra = 15'd0; assign mig_p5_cmd_ba = 3'd0; assign mig_p5_cmd_ca = 12'd0; assign mig_p5_cmd_instr = 3'd0; assign mig_p5_cmd_bl = 6'd0; end else if(C_PORT_CONFIG == "B128" ) begin : u_config_5 //*******************************BEGIN OF CONFIG 5 SIGNALS ******************************** // Inputs from Application CMD Port assign mig_p0_arb_en = p0_arb_en ; assign mig_p0_cmd_clk = p0_cmd_clk ; assign mig_p0_cmd_en = p0_cmd_en ; assign mig_p0_cmd_ra = p0_cmd_ra ; assign mig_p0_cmd_ba = p0_cmd_ba ; assign mig_p0_cmd_ca = p0_cmd_ca ; assign mig_p0_cmd_instr = p0_cmd_instr; assign mig_p0_cmd_bl = {(p0_cmd_instr[2] | p0_cmd_bl[5]),p0_cmd_bl[4:0]} ; assign p0_cmd_empty = mig_p0_cmd_empty ; assign p0_cmd_full = mig_p0_cmd_full ; // Inputs from Application User Port assign mig_p0_wr_clk = p0_wr_clk; assign mig_p0_rd_clk = p0_rd_clk; assign mig_p1_wr_clk = p0_wr_clk; assign mig_p1_rd_clk = p0_rd_clk; assign mig_p2_clk = p0_rd_clk; assign mig_p3_clk = p0_wr_clk; assign mig_p4_clk = p0_rd_clk; assign mig_p5_clk = p0_wr_clk; assign mig_p0_wr_en = p0_wr_en & !p0_wr_full; assign mig_p1_wr_en = p0_wr_en & !p0_wr_full; assign mig_p3_en = p0_wr_en & !p0_wr_full; assign mig_p5_en = p0_wr_en & !p0_wr_full; assign mig_p0_wr_data = p0_wr_data[31:0]; assign mig_p0_wr_mask = p0_wr_mask[3:0]; assign mig_p1_wr_data = p0_wr_data[63 : 32]; assign mig_p1_wr_mask = p0_wr_mask[7 : 4]; assign mig_p3_wr_data = p0_wr_data[95 : 64]; assign mig_p3_wr_mask = p0_wr_mask[11 : 8]; assign mig_p5_wr_data = p0_wr_data[127 : 96]; assign mig_p5_wr_mask = p0_wr_mask[15 : 12]; assign mig_p0_rd_en = p0_rd_en & !p0_rd_empty; assign mig_p1_rd_en = p0_rd_en & !p0_rd_empty; assign mig_p2_en = p0_rd_en & !p0_rd_empty; assign mig_p4_en = p0_rd_en & !p0_rd_empty; // outputs to Applications User Port assign p0_rd_data = {mig_p4_rd_data , mig_p2_rd_data , mig_p1_rd_data , mig_p0_rd_data}; assign p0_rd_empty = mig_p4_empty; assign p0_rd_full = mig_p4_full; assign p0_rd_error = mig_p0_rd_error | mig_p1_rd_error | mig_p2_error | mig_p4_error; assign p0_rd_overflow = mig_p0_rd_overflow | mig_p1_rd_overflow | mig_p2_overflow | mig_p4_overflow; assign p0_wr_underrun = mig_p0_wr_underrun | mig_p1_wr_underrun | mig_p3_underrun | mig_p5_underrun; assign p0_wr_empty = mig_p5_empty; assign p0_wr_full = mig_p5_full; assign p0_wr_error = mig_p0_wr_error | mig_p1_wr_error | mig_p3_error | mig_p5_error; assign p0_wr_count = mig_p5_count; assign p0_rd_count = mig_p4_count; // unused MCB's siganls in this configuration assign mig_p1_arb_en = 1'b0; assign mig_p1_cmd_clk = 1'b0; assign mig_p1_cmd_en = 1'b0; assign mig_p1_cmd_ra = 15'd0; assign mig_p1_cmd_ba = 3'd0; assign mig_p1_cmd_ca = 12'd0; assign mig_p1_cmd_instr = 3'd0; assign mig_p1_cmd_bl = 6'd0; assign mig_p2_arb_en = 1'b0; assign mig_p2_cmd_clk = 1'b0; assign mig_p2_cmd_en = 1'b0; assign mig_p2_cmd_ra = 15'd0; assign mig_p2_cmd_ba = 3'd0; assign mig_p2_cmd_ca = 12'd0; assign mig_p2_cmd_instr = 3'd0; assign mig_p2_cmd_bl = 6'd0; assign mig_p3_arb_en = 1'b0; assign mig_p3_cmd_clk = 1'b0; assign mig_p3_cmd_en = 1'b0; assign mig_p3_cmd_ra = 15'd0; assign mig_p3_cmd_ba = 3'd0; assign mig_p3_cmd_ca = 12'd0; assign mig_p3_cmd_instr = 3'd0; assign mig_p3_cmd_bl = 6'd0; assign mig_p4_arb_en = 1'b0; assign mig_p4_cmd_clk = 1'b0; assign mig_p4_cmd_en = 1'b0; assign mig_p4_cmd_ra = 15'd0; assign mig_p4_cmd_ba = 3'd0; assign mig_p4_cmd_ca = 12'd0; assign mig_p4_cmd_instr = 3'd0; assign mig_p4_cmd_bl = 6'd0; assign mig_p5_arb_en = 1'b0; assign mig_p5_cmd_clk = 1'b0; assign mig_p5_cmd_en = 1'b0; assign mig_p5_cmd_ra = 15'd0; assign mig_p5_cmd_ba = 3'd0; assign mig_p5_cmd_ca = 12'd0; assign mig_p5_cmd_instr = 3'd0; assign mig_p5_cmd_bl = 6'd0; //*******************************END OF CONFIG 5 SIGNALS ******************************** end endgenerate MCB # ( .PORT_CONFIG (C_PORT_CONFIG), .MEM_WIDTH (C_NUM_DQ_PINS ), .MEM_TYPE (C_MEM_TYPE ), .MEM_BURST_LEN (C_MEM_BURST_LEN ), .MEM_ADDR_ORDER (C_MEM_ADDR_ORDER), .MEM_CAS_LATENCY (C_MEM_CAS_LATENCY), .MEM_DDR3_CAS_LATENCY (C_MEM_DDR3_CAS_LATENCY ), .MEM_DDR2_WRT_RECOVERY (C_MEM_DDR2_WRT_RECOVERY ), .MEM_DDR3_WRT_RECOVERY (C_MEM_DDR3_WRT_RECOVERY ), .MEM_MOBILE_PA_SR (C_MEM_MOBILE_PA_SR ), .MEM_DDR1_2_ODS (C_MEM_DDR1_2_ODS ), .MEM_DDR3_ODS (C_MEM_DDR3_ODS ), .MEM_DDR2_RTT (C_MEM_DDR2_RTT ), .MEM_DDR3_RTT (C_MEM_DDR3_RTT ), .MEM_DDR3_ADD_LATENCY (C_MEM_DDR3_ADD_LATENCY ), .MEM_DDR2_ADD_LATENCY (C_MEM_DDR2_ADD_LATENCY ), .MEM_MOBILE_TC_SR (C_MEM_MOBILE_TC_SR ), .MEM_MDDR_ODS (C_MEM_MDDR_ODS ), .MEM_DDR2_DIFF_DQS_EN (C_MEM_DDR2_DIFF_DQS_EN ), .MEM_DDR2_3_PA_SR (C_MEM_DDR2_3_PA_SR ), .MEM_DDR3_CAS_WR_LATENCY (C_MEM_DDR3_CAS_WR_LATENCY), .MEM_DDR3_AUTO_SR (C_MEM_DDR3_AUTO_SR ), .MEM_DDR2_3_HIGH_TEMP_SR (C_MEM_DDR2_3_HIGH_TEMP_SR), .MEM_DDR3_DYN_WRT_ODT (C_MEM_DDR3_DYN_WRT_ODT ), .MEM_RA_SIZE (C_MEM_ADDR_WIDTH ), .MEM_BA_SIZE (C_MEM_BANKADDR_WIDTH ), .MEM_CA_SIZE (C_MEM_NUM_COL_BITS ), .MEM_RAS_VAL (MEM_RAS_VAL ), .MEM_RCD_VAL (MEM_RCD_VAL ), .MEM_REFI_VAL (MEM_REFI_VAL ), .MEM_RFC_VAL (MEM_RFC_VAL ), .MEM_RP_VAL (MEM_RP_VAL ), .MEM_WR_VAL (MEM_WR_VAL ), .MEM_RTP_VAL (MEM_RTP_VAL ), .MEM_WTR_VAL (MEM_WTR_VAL ), .CAL_BYPASS (C_MC_CALIB_BYPASS), .CAL_RA (C_MC_CALIBRATION_RA), .CAL_BA (C_MC_CALIBRATION_BA ), .CAL_CA (C_MC_CALIBRATION_CA), .CAL_CLK_DIV (C_MC_CALIBRATION_CLK_DIV), .CAL_DELAY (C_MC_CALIBRATION_DELAY), .ARB_NUM_TIME_SLOTS (C_ARB_NUM_TIME_SLOTS), .ARB_TIME_SLOT_0 (arbtimeslot0 ) , .ARB_TIME_SLOT_1 (arbtimeslot1 ) , .ARB_TIME_SLOT_2 (arbtimeslot2 ) , .ARB_TIME_SLOT_3 (arbtimeslot3 ) , .ARB_TIME_SLOT_4 (arbtimeslot4 ) , .ARB_TIME_SLOT_5 (arbtimeslot5 ) , .ARB_TIME_SLOT_6 (arbtimeslot6 ) , .ARB_TIME_SLOT_7 (arbtimeslot7 ) , .ARB_TIME_SLOT_8 (arbtimeslot8 ) , .ARB_TIME_SLOT_9 (arbtimeslot9 ) , .ARB_TIME_SLOT_10 (arbtimeslot10) , .ARB_TIME_SLOT_11 (arbtimeslot11) ) samc_0 ( // HIGH-SPEED PLL clock interface .PLLCLK ({ioclk90,ioclk0}), .PLLCE ({pll_ce_90,pll_ce_0}) , .PLLLOCK (1'b1), // DQS CLOCK NETWork interface .DQSIOIN (idelay_dqs_ioi_s), .DQSIOIP (idelay_dqs_ioi_m), .UDQSIOIN (idelay_udqs_ioi_s), .UDQSIOIP (idelay_udqs_ioi_m), //.DQSPIN (in_pre_dqsp), .DQI (in_dq), // RESETS - GLOBAl & local .SYSRST (MCB_SYSRST ), // command port 0 .P0ARBEN (mig_p0_arb_en), .P0CMDCLK (mig_p0_cmd_clk), .P0CMDEN (mig_p0_cmd_en), .P0CMDRA (mig_p0_cmd_ra), .P0CMDBA (mig_p0_cmd_ba), .P0CMDCA (mig_p0_cmd_ca), .P0CMDINSTR (mig_p0_cmd_instr), .P0CMDBL (mig_p0_cmd_bl), .P0CMDEMPTY (mig_p0_cmd_empty), .P0CMDFULL (mig_p0_cmd_full), // command port 1 .P1ARBEN (mig_p1_arb_en), .P1CMDCLK (mig_p1_cmd_clk), .P1CMDEN (mig_p1_cmd_en), .P1CMDRA (mig_p1_cmd_ra), .P1CMDBA (mig_p1_cmd_ba), .P1CMDCA (mig_p1_cmd_ca), .P1CMDINSTR (mig_p1_cmd_instr), .P1CMDBL (mig_p1_cmd_bl), .P1CMDEMPTY (mig_p1_cmd_empty), .P1CMDFULL (mig_p1_cmd_full), // command port 2 .P2ARBEN (mig_p2_arb_en), .P2CMDCLK (mig_p2_cmd_clk), .P2CMDEN (mig_p2_cmd_en), .P2CMDRA (mig_p2_cmd_ra), .P2CMDBA (mig_p2_cmd_ba), .P2CMDCA (mig_p2_cmd_ca), .P2CMDINSTR (mig_p2_cmd_instr), .P2CMDBL (mig_p2_cmd_bl), .P2CMDEMPTY (mig_p2_cmd_empty), .P2CMDFULL (mig_p2_cmd_full), // command port 3 .P3ARBEN (mig_p3_arb_en), .P3CMDCLK (mig_p3_cmd_clk), .P3CMDEN (mig_p3_cmd_en), .P3CMDRA (mig_p3_cmd_ra), .P3CMDBA (mig_p3_cmd_ba), .P3CMDCA (mig_p3_cmd_ca), .P3CMDINSTR (mig_p3_cmd_instr), .P3CMDBL (mig_p3_cmd_bl), .P3CMDEMPTY (mig_p3_cmd_empty), .P3CMDFULL (mig_p3_cmd_full), // command port 4 // don't care in config 2 .P4ARBEN (mig_p4_arb_en), .P4CMDCLK (mig_p4_cmd_clk), .P4CMDEN (mig_p4_cmd_en), .P4CMDRA (mig_p4_cmd_ra), .P4CMDBA (mig_p4_cmd_ba), .P4CMDCA (mig_p4_cmd_ca), .P4CMDINSTR (mig_p4_cmd_instr), .P4CMDBL (mig_p4_cmd_bl), .P4CMDEMPTY (mig_p4_cmd_empty), .P4CMDFULL (mig_p4_cmd_full), // command port 5 // don't care in config 2 .P5ARBEN (mig_p5_arb_en), .P5CMDCLK (mig_p5_cmd_clk), .P5CMDEN (mig_p5_cmd_en), .P5CMDRA (mig_p5_cmd_ra), .P5CMDBA (mig_p5_cmd_ba), .P5CMDCA (mig_p5_cmd_ca), .P5CMDINSTR (mig_p5_cmd_instr), .P5CMDBL (mig_p5_cmd_bl), .P5CMDEMPTY (mig_p5_cmd_empty), .P5CMDFULL (mig_p5_cmd_full), // IOI & IOB SIGNals/tristate interface .DQIOWEN0 (dqIO_w_en_0), .DQSIOWEN90P (dqsIO_w_en_90_p), .DQSIOWEN90N (dqsIO_w_en_90_n), // IOB MEMORY INTerface signals .ADDR (address_90), .BA (ba_90 ), .RAS (ras_90 ), .CAS (cas_90 ), .WE (we_90 ), .CKE (cke_90 ), .ODT (odt_90 ), .RST (rst_90 ), // CALIBRATION DRP interface .IOIDRPCLK (ioi_drp_clk ), .IOIDRPADDR (ioi_drp_addr ), .IOIDRPSDO (ioi_drp_sdo ), .IOIDRPSDI (ioi_drp_sdi ), .IOIDRPCS (ioi_drp_cs ), .IOIDRPADD (ioi_drp_add ), .IOIDRPBROADCAST (ioi_drp_broadcast ), .IOIDRPTRAIN (ioi_drp_train ), .IOIDRPUPDATE (ioi_drp_update) , // CALIBRATION DAtacapture interface //SPECIAL COMMANDs .RECAL (mcb_recal ), .UIREAD (mcb_ui_read), .UIADD (mcb_ui_add) , .UICS (mcb_ui_cs) , .UICLK (mcb_ui_clk) , .UISDI (mcb_ui_sdi) , .UIADDR (mcb_ui_addr) , .UIBROADCAST (mcb_ui_broadcast) , .UIDRPUPDATE (mcb_ui_drp_update) , .UIDONECAL (mcb_ui_done_cal) , .UICMD (mcb_ui_cmd), .UICMDIN (mcb_ui_cmd_in) , .UICMDEN (mcb_ui_cmd_en) , .UIDQCOUNT (mcb_ui_dqcount) , .UIDQLOWERDEC (mcb_ui_dq_lower_dec), .UIDQLOWERINC (mcb_ui_dq_lower_inc), .UIDQUPPERDEC (mcb_ui_dq_upper_dec), .UIDQUPPERINC (mcb_ui_dq_upper_inc), .UIUDQSDEC (mcb_ui_udqs_dec), .UIUDQSINC (mcb_ui_udqs_inc), .UILDQSDEC (mcb_ui_ldqs_dec), .UILDQSINC (mcb_ui_ldqs_inc), .UODATA (uo_data), .UODATAVALID (uo_data_valid), .UODONECAL (hard_done_cal) , .UOCMDREADYIN (uo_cmd_ready_in), .UOREFRSHFLAG (uo_refrsh_flag), .UOCALSTART (uo_cal_start) , .UOSDO (uo_sdo), //CONTROL SIGNALS .STATUS (status), .SELFREFRESHENTER (selfrefresh_mcb_enter ), .SELFREFRESHMODE (selfrefresh_mcb_mode ), ////////////////////////////// ////////////////// //MUIs //////////////////////////////////////////////// .P0RDDATA ( mig_p0_rd_data[31:0] ), .P1RDDATA ( mig_p1_rd_data[31:0] ), .P2RDDATA ( mig_p2_rd_data[31:0] ), .P3RDDATA ( mig_p3_rd_data[31:0] ), .P4RDDATA ( mig_p4_rd_data[31:0] ), .P5RDDATA ( mig_p5_rd_data[31:0] ), .LDMN ( dqnlm ), .UDMN ( dqnum ), .DQON ( dqo_n ), .DQOP ( dqo_p ), .LDMP ( dqplm ), .UDMP ( dqpum ), .P0RDCOUNT ( mig_p0_rd_count ), .P0WRCOUNT ( mig_p0_wr_count ), .P1RDCOUNT ( mig_p1_rd_count ), .P1WRCOUNT ( mig_p1_wr_count ), .P2COUNT ( mig_p2_count ), .P3COUNT ( mig_p3_count ), .P4COUNT ( mig_p4_count ), .P5COUNT ( mig_p5_count ), // NEW ADDED FIFo status siganls // MIG USER PORT 0 .P0RDEMPTY ( mig_p0_rd_empty), .P0RDFULL ( mig_p0_rd_full), .P0RDOVERFLOW ( mig_p0_rd_overflow), .P0WREMPTY ( mig_p0_wr_empty), .P0WRFULL ( mig_p0_wr_full), .P0WRUNDERRUN ( mig_p0_wr_underrun), // MIG USER PORT 1 .P1RDEMPTY ( mig_p1_rd_empty), .P1RDFULL ( mig_p1_rd_full), .P1RDOVERFLOW ( mig_p1_rd_overflow), .P1WREMPTY ( mig_p1_wr_empty), .P1WRFULL ( mig_p1_wr_full), .P1WRUNDERRUN ( mig_p1_wr_underrun), // MIG USER PORT 2 .P2EMPTY ( mig_p2_empty), .P2FULL ( mig_p2_full), .P2RDOVERFLOW ( mig_p2_overflow), .P2WRUNDERRUN ( mig_p2_underrun), .P3EMPTY ( mig_p3_empty ), .P3FULL ( mig_p3_full ), .P3RDOVERFLOW ( mig_p3_overflow), .P3WRUNDERRUN ( mig_p3_underrun ), // MIG USER PORT 3 .P4EMPTY ( mig_p4_empty), .P4FULL ( mig_p4_full), .P4RDOVERFLOW ( mig_p4_overflow), .P4WRUNDERRUN ( mig_p4_underrun), .P5EMPTY ( mig_p5_empty ), .P5FULL ( mig_p5_full ), .P5RDOVERFLOW ( mig_p5_overflow), .P5WRUNDERRUN ( mig_p5_underrun), ////////////////////////////////////////////////////////- .P0WREN ( mig_p0_wr_en), .P0RDEN ( mig_p0_rd_en), .P1WREN ( mig_p1_wr_en), .P1RDEN ( mig_p1_rd_en), .P2EN ( mig_p2_en), .P3EN ( mig_p3_en), .P4EN ( mig_p4_en), .P5EN ( mig_p5_en), // WRITE MASK BIts connection .P0RWRMASK ( mig_p0_wr_mask[3:0]), .P1RWRMASK ( mig_p1_wr_mask[3:0]), .P2WRMASK ( mig_p2_wr_mask[3:0]), .P3WRMASK ( mig_p3_wr_mask[3:0]), .P4WRMASK ( mig_p4_wr_mask[3:0]), .P5WRMASK ( mig_p5_wr_mask[3:0]), // DATA WRITE COnnection .P0WRDATA ( mig_p0_wr_data[31:0]), .P1WRDATA ( mig_p1_wr_data[31:0]), .P2WRDATA ( mig_p2_wr_data[31:0]), .P3WRDATA ( mig_p3_wr_data[31:0]), .P4WRDATA ( mig_p4_wr_data[31:0]), .P5WRDATA ( mig_p5_wr_data[31:0]), .P0WRERROR (mig_p0_wr_error), .P1WRERROR (mig_p1_wr_error), .P0RDERROR (mig_p0_rd_error), .P1RDERROR (mig_p1_rd_error), .P2ERROR (mig_p2_error), .P3ERROR (mig_p3_error), .P4ERROR (mig_p4_error), .P5ERROR (mig_p5_error), // USER SIDE DAta ports clock // 128 BITS CONnections .P0WRCLK ( mig_p0_wr_clk ), .P1WRCLK ( mig_p1_wr_clk ), .P0RDCLK ( mig_p0_rd_clk ), .P1RDCLK ( mig_p1_rd_clk ), .P2CLK ( mig_p2_clk ), .P3CLK ( mig_p3_clk ), .P4CLK ( mig_p4_clk ), .P5CLK ( mig_p5_clk) //////////////////////////////////////////////////////// // TST MODE PINS ); ////////////////////////////////////////////////////// // Input Termination Calibration ////////////////////////////////////////////////////// wire DONE_SOFTANDHARD_CAL; assign uo_done_cal = ( C_CALIB_SOFT_IP == "TRUE") ? DONE_SOFTANDHARD_CAL : hard_done_cal; generate if ( C_CALIB_SOFT_IP == "TRUE") begin: gen_term_calib mcb_soft_calibration_top # ( .C_MEM_TZQINIT_MAXCNT (C_MEM_TZQINIT_MAXCNT), .C_MC_CALIBRATION_MODE(C_MC_CALIBRATION_MODE), .SKIP_IN_TERM_CAL (C_SKIP_IN_TERM_CAL), .SKIP_DYNAMIC_CAL (C_SKIP_DYNAMIC_CAL), .SKIP_DYN_IN_TERM (C_SKIP_DYN_IN_TERM), .C_SIMULATION (C_SIMULATION), .C_MEM_TYPE (C_MEM_TYPE) ) mcb_soft_calibration_top_inst ( .UI_CLK (ui_clk), //Input - global clock to be used for input_term_tuner and IODRP clock .RST (int_sys_rst), //Input - reset for input_term_tuner - synchronous for input_term_tuner state machine, asynch for IODRP (sub)controller .IOCLK (ioclk0), //Input - IOCLK input to the IODRP's .DONE_SOFTANDHARD_CAL (DONE_SOFTANDHARD_CAL), // active high flag signals soft calibration of input delays is complete and MCB_UODONECAL is high (MCB hard calib complete) .PLL_LOCK (pll_lock), .SELFREFRESH_REQ (selfrefresh_enter), // from user app .SELFREFRESH_MCB_MODE (selfrefresh_mcb_mode), // from MCB .SELFREFRESH_MCB_REQ (selfrefresh_mcb_enter),// to mcb .SELFREFRESH_MODE (selfrefresh_mode), // to user app .MCB_UIADD (mcb_ui_add), .MCB_UISDI (mcb_ui_sdi), .MCB_UOSDO (uo_sdo), // from MCB's UOSDO port (User output SDO) .MCB_UODONECAL (hard_done_cal), // input for when MCB hard calibration process is complete .MCB_UOREFRSHFLAG (uo_refrsh_flag), //high during refresh cycle and time when MCB is innactive .MCB_UICS (mcb_ui_cs), // to MCB's UICS port (User Input CS) .MCB_UIDRPUPDATE (mcb_ui_drp_update), // MCB's UIDRPUPDATE port (gets passed to IODRP2_MCB's MEMUPDATE port: this controls shadow latch used during IODRP2_MCB writes). Currently just trasnparent .MCB_UIBROADCAST (mcb_ui_broadcast), // to MCB's UIBROADCAST port (User Input BROADCAST - gets passed to IODRP2_MCB's BKST port) .MCB_UIADDR (mcb_ui_addr), //to MCB's UIADDR port (gets passed to IODRP2_MCB's AUXADDR port .MCB_UICMDEN (mcb_ui_cmd_en), //set to take control of UI interface - removes control from internal calib block .MCB_UIDONECAL (mcb_ui_done_cal), // .MCB_UIDQLOWERDEC (mcb_ui_dq_lower_dec), .MCB_UIDQLOWERINC (mcb_ui_dq_lower_inc), .MCB_UIDQUPPERDEC (mcb_ui_dq_upper_dec), .MCB_UIDQUPPERINC (mcb_ui_dq_upper_inc), .MCB_UILDQSDEC (mcb_ui_ldqs_dec), .MCB_UILDQSINC (mcb_ui_ldqs_inc), .MCB_UIREAD (mcb_ui_read), //enables read w/o writing by turning on a SDO->SDI loopback inside the IODRP2_MCBs (doesn't exist in regular IODRP2). IODRPCTRLR_R_WB becomes don't-care. .MCB_UIUDQSDEC (mcb_ui_udqs_dec), .MCB_UIUDQSINC (mcb_ui_udqs_inc), .MCB_RECAL (mcb_recal), .MCB_SYSRST (MCB_SYSRST), //drives the MCB's SYSRST pin - the main reset for MCB .MCB_UICMD (mcb_ui_cmd), .MCB_UICMDIN (mcb_ui_cmd_in), .MCB_UIDQCOUNT (mcb_ui_dqcount), .MCB_UODATA (uo_data), .MCB_UODATAVALID (uo_data_valid), .MCB_UOCMDREADY (uo_cmd_ready_in), .MCB_UO_CAL_START (uo_cal_start), .RZQ_Pin (rzq), .ZIO_Pin (zio), .CKE_Train (cke_train) ); assign mcb_ui_clk = ui_clk; end endgenerate generate if ( C_CALIB_SOFT_IP != "TRUE") begin: gen_no_term_calib assign DONE_SOFTANDHARD_CAL = 1'b0; assign MCB_SYSRST = int_sys_rst | (~wait_200us_counter[15]); assign mcb_recal = calib_recal; assign mcb_ui_read = ui_read; assign mcb_ui_add = ui_add; assign mcb_ui_cs = ui_cs; assign mcb_ui_clk = ui_clk; assign mcb_ui_sdi = ui_sdi; assign mcb_ui_addr = ui_addr; assign mcb_ui_broadcast = ui_broadcast; assign mcb_ui_drp_update = ui_drp_update; assign mcb_ui_done_cal = ui_done_cal; assign mcb_ui_cmd = ui_cmd; assign mcb_ui_cmd_in = ui_cmd_in; assign mcb_ui_cmd_en = ui_cmd_en; assign mcb_ui_dq_lower_dec = ui_dq_lower_dec; assign mcb_ui_dq_lower_inc = ui_dq_lower_inc; assign mcb_ui_dq_upper_dec = ui_dq_upper_dec; assign mcb_ui_dq_upper_inc = ui_dq_upper_inc; assign mcb_ui_udqs_inc = ui_udqs_inc; assign mcb_ui_udqs_dec = ui_udqs_dec; assign mcb_ui_ldqs_inc = ui_ldqs_inc; assign mcb_ui_ldqs_dec = ui_ldqs_dec; assign selfrefresh_mode = 1'b0; if (C_SIMULATION == "FALSE") begin: init_sequence always @ (posedge ui_clk, posedge int_sys_rst) begin if (int_sys_rst) wait_200us_counter <= 'b0; else if (wait_200us_counter[15]) // UI_CLK maximum is up to 100 MHz. wait_200us_counter <= wait_200us_counter ; else wait_200us_counter <= wait_200us_counter + 1'b1; end end else begin: init_sequence_skip // synthesis translate_off initial begin wait_200us_counter = 16'hFFFF; $display("The 200 us wait period required before CKE goes active has been skipped in Simulation\n"); end // synthesis translate_on end if( C_MEM_TYPE == "DDR2") begin : gen_cketrain_a always @ ( posedge ui_clk) begin // When wait_200us_[13] and wait_200us_[14] are both asserted, // 200 us wait should have been passed. if (wait_200us_counter[14] && wait_200us_counter[13]) wait_200us_done_r1 <= 1'b1; else wait_200us_done_r1 <= 1'b0; wait_200us_done_r2 <= wait_200us_done_r1; end always @ ( posedge ui_clk, posedge int_sys_rst) begin if (int_sys_rst) cke_train_reg <= 1'b0; else if ( wait_200us_done_r1 && ~wait_200us_done_r2 ) cke_train_reg <= 1'b1; else if ( uo_done_cal) cke_train_reg <= 1'b0; end assign cke_train = cke_train_reg; end if( C_MEM_TYPE != "DDR2") begin : gen_cketrain_b assign cke_train = 1'b0; end end endgenerate ////////////////////////////////////////////////////// //ODDRDES2 instantiations ////////////////////////////////////////////////////// //////// //ADDR //////// genvar addr_ioi; generate for(addr_ioi = 0; addr_ioi < C_MEM_ADDR_WIDTH; addr_ioi = addr_ioi + 1) begin : gen_addr_oserdes2 OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_addr_0 ( .OQ(ioi_addr[addr_ioi]), .SHIFTOUT1(), .SHIFTOUT2(), .SHIFTOUT3(), .SHIFTOUT4(), .TQ(t_addr[addr_ioi]), .CLK0(ioclk0), .CLK1(), .CLKDIV(), .D1(address_90[addr_ioi]), .D2(address_90[addr_ioi]), .D3(), .D4(), .IOCE(pll_ce_0), .OCE(1'b1), .RST(int_sys_rst), .SHIFTIN1(), .SHIFTIN2(), .SHIFTIN3(), .SHIFTIN4(), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN(1'b0) ); end endgenerate //////// //BA //////// genvar ba_ioi; generate for(ba_ioi = 0; ba_ioi < C_MEM_BANKADDR_WIDTH; ba_ioi = ba_ioi + 1) begin : gen_ba_oserdes2 OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_ba_0 ( .OQ (ioi_ba[ba_ioi]), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (t_ba[ba_ioi]), .CLK0 (ioclk0), .CLK1 (), .CLKDIV (), .D1 (ba_90[ba_ioi]), .D2 (ba_90[ba_ioi]), .D3 (), .D4 (), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN (1'b0) ); end endgenerate //////// //CAS //////// OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_cas_0 ( .OQ (ioi_cas), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (t_cas), .CLK0 (ioclk0), .CLK1 (), .CLKDIV (), .D1 (cas_90), .D2 (cas_90), .D3 (), .D4 (), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN (1'b0) ); //////// //CKE //////// OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) , // {1..8} .TRAIN_PATTERN (15) ) ioi_cke_0 ( .OQ (ioi_cke), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (t_cke), .CLK0 (ioclk0), .CLK1 (), .CLKDIV (), .D1 (cke_90), .D2 (cke_90), .D3 (), .D4 (), .IOCE (pll_ce_0), .OCE (1'b1), .RST (1'b0),//int_sys_rst .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN (cke_train) ); //////// //ODT //////// generate if(C_MEM_TYPE == "DDR3" || C_MEM_TYPE == "DDR2" ) begin : gen_ioi_odt OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_odt_0 ( .OQ (ioi_odt), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (t_odt), .CLK0 (ioclk0), .CLK1 (), .CLKDIV (), .D1 (odt_90), .D2 (odt_90), .D3 (), .D4 (), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN (1'b0) ); end endgenerate //////// //RAS //////// OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_ras_0 ( .OQ (ioi_ras), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (t_ras), .CLK0 (ioclk0), .CLK1 (), .CLKDIV (), .D1 (ras_90), .D2 (ras_90), .D3 (), .D4 (), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1 (1'b0), .T2 (1'b0), .T3 (), .T4 (), .TCE (1'b1), .TRAIN (1'b0) ); //////// //RST //////// generate if (C_MEM_TYPE == "DDR3" ) begin : gen_ioi_rst OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_rst_0 ( .OQ (ioi_rst), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (t_rst), .CLK0 (ioclk0), .CLK1 (), .CLKDIV (), .D1 (rst_90), .D2 (rst_90), .D3 (), .D4 (), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN (1'b0) ); end endgenerate //////// //WE //////// OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_we_0 ( .OQ (ioi_we), .TQ (t_we), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .CLK0 (ioclk0), .CLK1 (), .CLKDIV (), .D1 (we_90), .D2 (we_90), .D3 (), .D4 (), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN (1'b0) ); //////// //CK //////// OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_ck_0 ( .OQ (ioi_ck), .SHIFTOUT1(), .SHIFTOUT2(), .SHIFTOUT3(), .SHIFTOUT4(), .TQ (t_ck), .CLK0 (ioclk0), .CLK1(), .CLKDIV(), .D1 (1'b0), .D2 (1'b1), .D3(), .D4(), .IOCE (pll_ce_0), .OCE (1'b1), .RST (1'b0),//int_sys_rst .SHIFTIN1(), .SHIFTIN2(), .SHIFTIN3 (), .SHIFTIN4 (), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN (1'b0) ); //////// //CKN //////// /* OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_SLAVE), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_ckn_0 ( .OQ (ioi_ckn), .SHIFTOUT1(), .SHIFTOUT2(), .SHIFTOUT3(), .SHIFTOUT4(), .TQ (t_ckn), .CLK0 (ioclk0), .CLK1(), .CLKDIV(), .D1 (1'b1), .D2 (1'b0), .D3(), .D4(), .IOCE (pll_ce_0), .OCE (1'b1), .RST (1'b0),//int_sys_rst .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3(), .SHIFTIN4(), .T1(1'b0), .T2(1'b0), .T3(), .T4(), .TCE(1'b1), .TRAIN (1'b0) ); */ //////// //UDM //////// wire udm_oq; wire udm_t; OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_udm_0 ( .OQ (udm_oq), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (udm_t), .CLK0 (ioclk90), .CLK1 (), .CLKDIV (), .D1 (dqpum), .D2 (dqnum), .D3 (), .D4 (), .IOCE (pll_ce_90), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1 (dqIO_w_en_0), .T2 (dqIO_w_en_0), .T3 (), .T4 (), .TCE (1'b1), .TRAIN (1'b0) ); //////// //LDM //////// wire ldm_oq; wire ldm_t; OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) ioi_ldm_0 ( .OQ (ldm_oq), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (ldm_t), .CLK0 (ioclk90), .CLK1 (), .CLKDIV (), .D1 (dqplm), .D2 (dqnlm), .D3 (), .D4 (), .IOCE (pll_ce_90), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1 (dqIO_w_en_0), .T2 (dqIO_w_en_0), .T3 (), .T4 (), .TCE (1'b1), .TRAIN (1'b0) ); //////// //DQ //////// wire dq_oq [C_NUM_DQ_PINS-1:0]; wire dq_tq [C_NUM_DQ_PINS-1:0]; genvar dq; generate for(dq = 0; dq < C_NUM_DQ_PINS; dq = dq + 1) begin : gen_dq OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2), // {1..8} .TRAIN_PATTERN (5) // {0..15} ) oserdes2_dq_0 ( .OQ (dq_oq[dq]), .SHIFTOUT1 (), .SHIFTOUT2 (), .SHIFTOUT3 (), .SHIFTOUT4 (), .TQ (dq_tq[dq]), .CLK0 (ioclk90), .CLK1 (), .CLKDIV (), .D1 (dqo_p[dq]), .D2 (dqo_n[dq]), .D3 (), .D4 (), .IOCE (pll_ce_90), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3 (), .SHIFTIN4 (), .T1 (dqIO_w_en_0), .T2 (dqIO_w_en_0), .T3 (), .T4 (), .TCE (1'b1), .TRAIN (ioi_drp_train) ); end endgenerate //////// //DQSP //////// wire dqsp_oq ; wire dqsp_tq ; OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) oserdes2_dqsp_0 ( .OQ (dqsp_oq), .SHIFTOUT1(), .SHIFTOUT2(), .SHIFTOUT3(), .SHIFTOUT4(), .TQ (dqsp_tq), .CLK0 (ioclk0), .CLK1(), .CLKDIV(), .D1 (1'b0), .D2 (1'b1), .D3(), .D4(), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1(), .SHIFTIN2(), .SHIFTIN3 (), .SHIFTIN4 (), .T1 (dqsIO_w_en_90_n), .T2 (dqsIO_w_en_90_p), .T3(), .T4(), .TCE (1'b1), .TRAIN (1'b0) ); //////// //DQSN //////// wire dqsn_oq ; wire dqsn_tq ; OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_SLAVE), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) oserdes2_dqsn_0 ( .OQ (dqsn_oq), .SHIFTOUT1(), .SHIFTOUT2(), .SHIFTOUT3(), .SHIFTOUT4(), .TQ (dqsn_tq), .CLK0 (ioclk0), .CLK1(), .CLKDIV(), .D1 (1'b1), .D2 (1'b0), .D3(), .D4(), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3(), .SHIFTIN4(), .T1 (dqsIO_w_en_90_n), .T2 (dqsIO_w_en_90_p), .T3(), .T4(), .TCE (1'b1), .TRAIN (1'b0) ); //////// //UDQSP //////// wire udqsp_oq ; wire udqsp_tq ; OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_MASTER), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) oserdes2_udqsp_0 ( .OQ (udqsp_oq), .SHIFTOUT1(), .SHIFTOUT2(), .SHIFTOUT3(), .SHIFTOUT4(), .TQ (udqsp_tq), .CLK0 (ioclk0), .CLK1(), .CLKDIV(), .D1 (1'b0), .D2 (1'b1), .D3(), .D4(), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1(), .SHIFTIN2(), .SHIFTIN3 (), .SHIFTIN4 (), .T1 (dqsIO_w_en_90_n), .T2 (dqsIO_w_en_90_p), .T3(), .T4(), .TCE (1'b1), .TRAIN (1'b0) ); //////// //UDQSN //////// wire udqsn_oq ; wire udqsn_tq ; OSERDES2 #( .BYPASS_GCLK_FF ("TRUE"), .DATA_RATE_OQ (C_OSERDES2_DATA_RATE_OQ), // SDR, DDR | Data Rate setting .DATA_RATE_OT (C_OSERDES2_DATA_RATE_OT), // SDR, DDR, BUF | Tristate Rate setting. .OUTPUT_MODE (C_OSERDES2_OUTPUT_MODE_SE), // SINGLE_ENDED, DIFFERENTIAL .SERDES_MODE (C_OSERDES2_SERDES_MODE_SLAVE), // MASTER, SLAVE .DATA_WIDTH (2) // {1..8} ) oserdes2_udqsn_0 ( .OQ (udqsn_oq), .SHIFTOUT1(), .SHIFTOUT2(), .SHIFTOUT3(), .SHIFTOUT4(), .TQ (udqsn_tq), .CLK0 (ioclk0), .CLK1(), .CLKDIV(), .D1 (1'b1), .D2 (1'b0), .D3(), .D4(), .IOCE (pll_ce_0), .OCE (1'b1), .RST (int_sys_rst), .SHIFTIN1 (), .SHIFTIN2 (), .SHIFTIN3(), .SHIFTIN4(), .T1 (dqsIO_w_en_90_n), .T2 (dqsIO_w_en_90_p), .T3(), .T4(), .TCE (1'b1), .TRAIN (1'b0) ); //////////////////////////////////////////////////////// //OSDDRES2 instantiations end /////////////////////////////////////////////////////// wire aux_sdi_out_udqsp; wire aux_sdi_out_10; wire aux_sdi_out_11; wire aux_sdi_out_12; wire aux_sdi_out_14; wire aux_sdi_out_15; //////////////////////////////////////////////// //IODRP2 instantiations //////////////////////////////////////////////// generate if(C_NUM_DQ_PINS == 16 ) begin : dq_15_0_data //////////////////////////////////////////////// //IODRP2 instantiations //////////////////////////////////////////////// wire aux_sdi_out_14; wire aux_sdi_out_15; //////////////////////////////////////////////// //DQ14 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ14_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (7), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_14 ( .AUXSDO (aux_sdi_out_14), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[14]), .DQSOUTN(), .DQSOUTP (in_dq[14]), .SDO(), .TOUT (t_dq[14]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_15), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[14]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[14]), .SDI (ioi_drp_sdo), .T (dq_tq[14]) ); ///////////////////////////////////////////////// //DQ15 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ15_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (7), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_15 ( .AUXSDO (aux_sdi_out_15), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[15]), .DQSOUTN(), .DQSOUTP (in_dq[15]), .SDO(), .TOUT (t_dq[15]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (1'b0), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[15]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[15]), .SDI (ioi_drp_sdo), .T (dq_tq[15]) ); wire aux_sdi_out_12; wire aux_sdi_out_13; ///////////////////////////////////////////////// //DQ12 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ12_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (6), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_12 ( .AUXSDO (aux_sdi_out_12), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[12]), .DQSOUTN(), .DQSOUTP (in_dq[12]), .SDO(), .TOUT (t_dq[12]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_13), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[12]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[12]), .SDI (ioi_drp_sdo), .T (dq_tq[12]) ); ///////////////////////////////////////////////// //DQ13 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ13_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (6), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_13 ( .AUXSDO (aux_sdi_out_13), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[13]), .DQSOUTN(), .DQSOUTP (in_dq[13]), .SDO(), .TOUT (t_dq[13]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_14), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[13]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[13]), .SDI (ioi_drp_sdo), .T (dq_tq[13]) ); wire aux_sdi_out_udqsp; wire aux_sdi_out_udqsn; ///////// //UDQSP ///////// IODRP2_MCB #( .DATA_RATE (C_DQS_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (UDQSP_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (14), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQS_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_udqsp_0 ( .AUXSDO (aux_sdi_out_udqsp), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_udqs), .DQSOUTN(), .DQSOUTP (idelay_udqs_ioi_m), .SDO(), .TOUT (t_udqs), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_udqsn), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_udqsp), .IOCLK0 (ioclk0), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (udqsp_oq), .SDI (ioi_drp_sdo), .T (udqsp_tq) ); ///////// //UDQSN ///////// IODRP2_MCB #( .DATA_RATE (C_DQS_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (UDQSN_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (14), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQS_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_udqsn_0 ( .AUXSDO (aux_sdi_out_udqsn), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_udqsn), .DQSOUTN(), .DQSOUTP (idelay_udqs_ioi_s), .SDO(), .TOUT (t_udqsn), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_12), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_udqsp), .IOCLK0 (ioclk0), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (udqsn_oq), .SDI (ioi_drp_sdo), .T (udqsn_tq) ); wire aux_sdi_out_10; wire aux_sdi_out_11; ///////////////////////////////////////////////// //DQ10 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ10_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (5), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_10 ( .AUXSDO (aux_sdi_out_10), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[10]), .DQSOUTN(), .DQSOUTP (in_dq[10]), .SDO(), .TOUT (t_dq[10]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_11), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[10]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[10]), .SDI (ioi_drp_sdo), .T (dq_tq[10]) ); ///////////////////////////////////////////////// //DQ11 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ11_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (5), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_11 ( .AUXSDO (aux_sdi_out_11), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[11]), .DQSOUTN(), .DQSOUTP (in_dq[11]), .SDO(), .TOUT (t_dq[11]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_udqsp), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[11]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[11]), .SDI (ioi_drp_sdo), .T (dq_tq[11]) ); wire aux_sdi_out_8; wire aux_sdi_out_9; ///////////////////////////////////////////////// //DQ8 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ8_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (4), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_8 ( .AUXSDO (aux_sdi_out_8), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[8]), .DQSOUTN(), .DQSOUTP (in_dq[8]), .SDO(), .TOUT (t_dq[8]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_9), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[8]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[8]), .SDI (ioi_drp_sdo), .T (dq_tq[8]) ); ///////////////////////////////////////////////// //DQ9 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ9_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (4), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_9 ( .AUXSDO (aux_sdi_out_9), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[9]), .DQSOUTN(), .DQSOUTP (in_dq[9]), .SDO(), .TOUT (t_dq[9]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_10), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[9]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[9]), .SDI (ioi_drp_sdo), .T (dq_tq[9]) ); wire aux_sdi_out_0; wire aux_sdi_out_1; ///////////////////////////////////////////////// //DQ0 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ0_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (0), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_0 ( .AUXSDO (aux_sdi_out_0), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[0]), .DQSOUTN(), .DQSOUTP (in_dq[0]), .SDO(), .TOUT (t_dq[0]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_1), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[0]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[0]), .SDI (ioi_drp_sdo), .T (dq_tq[0]) ); ///////////////////////////////////////////////// //DQ1 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ1_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (0), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_1 ( .AUXSDO (aux_sdi_out_1), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[1]), .DQSOUTN(), .DQSOUTP (in_dq[1]), .SDO(), .TOUT (t_dq[1]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_8), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[1]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[1]), .SDI (ioi_drp_sdo), .T (dq_tq[1]) ); wire aux_sdi_out_2; wire aux_sdi_out_3; ///////////////////////////////////////////////// //DQ2 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ2_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (1), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_2 ( .AUXSDO (aux_sdi_out_2), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[2]), .DQSOUTN(), .DQSOUTP (in_dq[2]), .SDO(), .TOUT (t_dq[2]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_3), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[2]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[2]), .SDI (ioi_drp_sdo), .T (dq_tq[2]) ); ///////////////////////////////////////////////// //DQ3 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ3_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (1), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_3 ( .AUXSDO (aux_sdi_out_3), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[3]), .DQSOUTN(), .DQSOUTP (in_dq[3]), .SDO(), .TOUT (t_dq[3]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_0), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[3]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[3]), .SDI (ioi_drp_sdo), .T (dq_tq[3]) ); wire aux_sdi_out_dqsp; wire aux_sdi_out_dqsn; ///////// //DQSP ///////// IODRP2_MCB #( .DATA_RATE (C_DQS_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (LDQSP_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (15), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQS_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dqsp_0 ( .AUXSDO (aux_sdi_out_dqsp), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dqs), .DQSOUTN(), .DQSOUTP (idelay_dqs_ioi_m), .SDO(), .TOUT (t_dqs), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_dqsn), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dqsp), .IOCLK0 (ioclk0), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dqsp_oq), .SDI (ioi_drp_sdo), .T (dqsp_tq) ); ///////// //DQSN ///////// IODRP2_MCB #( .DATA_RATE (C_DQS_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (LDQSN_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (15), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQS_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dqsn_0 ( .AUXSDO (aux_sdi_out_dqsn), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dqsn), .DQSOUTN(), .DQSOUTP (idelay_dqs_ioi_s), .SDO(), .TOUT (t_dqsn), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_2), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dqsp), .IOCLK0 (ioclk0), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dqsn_oq), .SDI (ioi_drp_sdo), .T (dqsn_tq) ); wire aux_sdi_out_6; wire aux_sdi_out_7; ///////////////////////////////////////////////// //DQ6 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ6_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (3), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_6 ( .AUXSDO (aux_sdi_out_6), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[6]), .DQSOUTN(), .DQSOUTP (in_dq[6]), .SDO(), .TOUT (t_dq[6]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_7), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[6]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[6]), .SDI (ioi_drp_sdo), .T (dq_tq[6]) ); ///////////////////////////////////////////////// //DQ7 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ7_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (3), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_7 ( .AUXSDO (aux_sdi_out_7), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[7]), .DQSOUTN(), .DQSOUTP (in_dq[7]), .SDO(), .TOUT (t_dq[7]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_dqsp), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[7]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[7]), .SDI (ioi_drp_sdo), .T (dq_tq[7]) ); wire aux_sdi_out_4; wire aux_sdi_out_5; ///////////////////////////////////////////////// //DQ4 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ4_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (2), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_4 ( .AUXSDO (aux_sdi_out_4), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[4]), .DQSOUTN(), .DQSOUTP (in_dq[4]), .SDO(), .TOUT (t_dq[4]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_5), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[4]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[4]), .SDI (ioi_drp_sdo), .T (dq_tq[4]) ); ///////////////////////////////////////////////// //DQ5 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ5_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (2), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_5 ( .AUXSDO (aux_sdi_out_5), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[5]), .DQSOUTN(), .DQSOUTP (in_dq[5]), .SDO(), .TOUT (t_dq[5]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_6), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[5]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[5]), .SDI (ioi_drp_sdo), .T (dq_tq[5]) ); //wire aux_sdi_out_udm; wire aux_sdi_out_ldm; ///////////////////////////////////////////////// //UDM //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (0), // 0 to 255 inclusive .MCB_ADDRESS (8), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_udm ( .AUXSDO (ioi_drp_sdi), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_udm), .DQSOUTN(), .DQSOUTP(), .SDO(), .TOUT (t_udm), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_ldm), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN(), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (udm_oq), .SDI (ioi_drp_sdo), .T (udm_t) ); ///////////////////////////////////////////////// //LDM //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (0), // 0 to 255 inclusive .MCB_ADDRESS (8), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_ldm ( .AUXSDO (aux_sdi_out_ldm), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_ldm), .DQSOUTN(), .DQSOUTP(), .SDO(), .TOUT (t_ldm), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_4), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN(), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (ldm_oq), .SDI (ioi_drp_sdo), .T (ldm_t) ); end endgenerate generate if(C_NUM_DQ_PINS == 8 ) begin : dq_7_0_data wire aux_sdi_out_0; wire aux_sdi_out_1; ///////////////////////////////////////////////// //DQ0 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ0_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (0), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_0 ( .AUXSDO (aux_sdi_out_0), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[0]), .DQSOUTN(), .DQSOUTP (in_dq[0]), .SDO(), .TOUT (t_dq[0]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_1), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[0]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[0]), .SDI (ioi_drp_sdo), .T (dq_tq[0]) ); ///////////////////////////////////////////////// //DQ1 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ1_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (0), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_1 ( .AUXSDO (aux_sdi_out_1), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[1]), .DQSOUTN(), .DQSOUTP (in_dq[1]), .SDO(), .TOUT (t_dq[1]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (1'b0), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[1]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[1]), .SDI (ioi_drp_sdo), .T (dq_tq[1]) ); wire aux_sdi_out_2; wire aux_sdi_out_3; ///////////////////////////////////////////////// //DQ2 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ2_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (1), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_2 ( .AUXSDO (aux_sdi_out_2), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[2]), .DQSOUTN(), .DQSOUTP (in_dq[2]), .SDO(), .TOUT (t_dq[2]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_3), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[2]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[2]), .SDI (ioi_drp_sdo), .T (dq_tq[2]) ); ///////////////////////////////////////////////// //DQ3 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ3_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (1), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_3 ( .AUXSDO (aux_sdi_out_3), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[3]), .DQSOUTN(), .DQSOUTP (in_dq[3]), .SDO(), .TOUT (t_dq[3]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_0), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[3]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[3]), .SDI (ioi_drp_sdo), .T (dq_tq[3]) ); wire aux_sdi_out_dqsp; wire aux_sdi_out_dqsn; ///////// //DQSP ///////// IODRP2_MCB #( .DATA_RATE (C_DQS_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (LDQSP_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (15), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQS_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dqsp_0 ( .AUXSDO (aux_sdi_out_dqsp), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dqs), .DQSOUTN(), .DQSOUTP (idelay_dqs_ioi_m), .SDO(), .TOUT (t_dqs), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_dqsn), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dqsp), .IOCLK0 (ioclk0), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dqsp_oq), .SDI (ioi_drp_sdo), .T (dqsp_tq) ); ///////// //DQSN ///////// IODRP2_MCB #( .DATA_RATE (C_DQS_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (LDQSN_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (15), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQS_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dqsn_0 ( .AUXSDO (aux_sdi_out_dqsn), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dqsn), .DQSOUTN(), .DQSOUTP (idelay_dqs_ioi_s), .SDO(), .TOUT (t_dqsn), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_2), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dqsp), .IOCLK0 (ioclk0), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dqsn_oq), .SDI (ioi_drp_sdo), .T (dqsn_tq) ); wire aux_sdi_out_6; wire aux_sdi_out_7; ///////////////////////////////////////////////// //DQ6 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ6_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (3), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_6 ( .AUXSDO (aux_sdi_out_6), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[6]), .DQSOUTN(), .DQSOUTP (in_dq[6]), .SDO(), .TOUT (t_dq[6]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_7), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[6]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[6]), .SDI (ioi_drp_sdo), .T (dq_tq[6]) ); ///////////////////////////////////////////////// //DQ7 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ7_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (3), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_7 ( .AUXSDO (aux_sdi_out_7), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[7]), .DQSOUTN(), .DQSOUTP (in_dq[7]), .SDO(), .TOUT (t_dq[7]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_dqsp), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[7]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[7]), .SDI (ioi_drp_sdo), .T (dq_tq[7]) ); wire aux_sdi_out_4; wire aux_sdi_out_5; ///////////////////////////////////////////////// //DQ4 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ4_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (2), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_4 ( .AUXSDO (aux_sdi_out_4), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[4]), .DQSOUTN(), .DQSOUTP (in_dq[4]), .SDO(), .TOUT (t_dq[4]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_5), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[4]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[4]), .SDI (ioi_drp_sdo), .T (dq_tq[4]) ); ///////////////////////////////////////////////// //DQ5 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ5_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (2), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_5 ( .AUXSDO (aux_sdi_out_5), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[5]), .DQSOUTN(), .DQSOUTP (in_dq[5]), .SDO(), .TOUT (t_dq[5]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_6), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[5]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[5]), .SDI (ioi_drp_sdo), .T (dq_tq[5]) ); //NEED TO GENERATE UDM so that user won't instantiate in this location //wire aux_sdi_out_udm; wire aux_sdi_out_ldm; ///////////////////////////////////////////////// //UDM //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (0), // 0 to 255 inclusive .MCB_ADDRESS (8), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_udm ( .AUXSDO (ioi_drp_sdi), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_udm), .DQSOUTN(), .DQSOUTP(), .SDO(), .TOUT (t_udm), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_ldm), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN(), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (udm_oq), .SDI (ioi_drp_sdo), .T (udm_t) ); ///////////////////////////////////////////////// //LDM //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (0), // 0 to 255 inclusive .MCB_ADDRESS (8), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_ldm ( .AUXSDO (aux_sdi_out_ldm), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_ldm), .DQSOUTN(), .DQSOUTP(), .SDO(), .TOUT (t_ldm), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_4), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN(), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (ldm_oq), .SDI (ioi_drp_sdo), .T (ldm_t) ); end endgenerate generate if(C_NUM_DQ_PINS == 4 ) begin : dq_3_0_data wire aux_sdi_out_0; wire aux_sdi_out_1; ///////////////////////////////////////////////// //DQ0 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ0_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (0), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_0 ( .AUXSDO (aux_sdi_out_0), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[0]), .DQSOUTN(), .DQSOUTP (in_dq[0]), .SDO(), .TOUT (t_dq[0]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_1), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[0]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[0]), .SDI (ioi_drp_sdo), .T (dq_tq[0]) ); ///////////////////////////////////////////////// //DQ1 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ1_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (0), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_1 ( .AUXSDO (aux_sdi_out_1), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[1]), .DQSOUTN(), .DQSOUTP (in_dq[1]), .SDO(), .TOUT (t_dq[1]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (1'b0), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[1]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[1]), .SDI (ioi_drp_sdo), .T (dq_tq[1]) ); wire aux_sdi_out_2; wire aux_sdi_out_3; ///////////////////////////////////////////////// //DQ2 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ2_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (1), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_2 ( .AUXSDO (aux_sdi_out_2), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[2]), .DQSOUTN(), .DQSOUTP (in_dq[2]), .SDO(), .TOUT (t_dq[2]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_3), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[2]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[2]), .SDI (ioi_drp_sdo), .T (dq_tq[2]) ); ///////////////////////////////////////////////// //DQ3 //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (DQ3_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (1), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_3 ( .AUXSDO (aux_sdi_out_3), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dq[3]), .DQSOUTN(), .DQSOUTP (in_dq[3]), .SDO(), .TOUT (t_dq[3]), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_0), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dq[3]), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dq_oq[3]), .SDI (ioi_drp_sdo), .T (dq_tq[3]) ); wire aux_sdi_out_dqsp; wire aux_sdi_out_dqsn; ///////// //DQSP ///////// IODRP2_MCB #( .DATA_RATE (C_DQS_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (LDQSP_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (15), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQS_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dqsp_0 ( .AUXSDO (aux_sdi_out_dqsp), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dqs), .DQSOUTN(), .DQSOUTP (idelay_dqs_ioi_m), .SDO(), .TOUT (t_dqs), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_dqsn), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dqsp), .IOCLK0 (ioclk0), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dqsp_oq), .SDI (ioi_drp_sdo), .T (dqsp_tq) ); ///////// //DQSN ///////// IODRP2_MCB #( .DATA_RATE (C_DQS_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (LDQSN_TAP_DELAY_VAL), // 0 to 255 inclusive .MCB_ADDRESS (15), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQS_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dqsn_0 ( .AUXSDO (aux_sdi_out_dqsn), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_dqsn), .DQSOUTN(), .DQSOUTP (idelay_dqs_ioi_s), .SDO(), .TOUT (t_dqsn), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_2), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN (in_pre_dqsp), .IOCLK0 (ioclk0), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (dqsn_oq), .SDI (ioi_drp_sdo), .T (dqsn_tq) ); //NEED TO GENERATE UDM so that user won't instantiate in this location //wire aux_sdi_out_udm; wire aux_sdi_out_ldm; ///////////////////////////////////////////////// //UDM //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (0), // 0 to 255 inclusive .MCB_ADDRESS (8), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_MASTER), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_udm ( .AUXSDO (ioi_drp_sdi), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_udm), .DQSOUTN(), .DQSOUTP(), .SDO(), .TOUT (t_udm), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_ldm), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN(), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (udm_oq), .SDI (ioi_drp_sdo), .T (udm_t) ); ///////////////////////////////////////////////// //LDM //////////////////////////////////////////////// IODRP2_MCB #( .DATA_RATE (C_DQ_IODRP2_DATA_RATE), // "SDR", "DDR" .IDELAY_VALUE (0), // 0 to 255 inclusive .MCB_ADDRESS (8), // 0 to 15 .ODELAY_VALUE (0), // 0 to 255 inclusive .SERDES_MODE (C_DQ_IODRP2_SERDES_MODE_SLAVE), // "NONE", "MASTER", "SLAVE" .SIM_TAPDELAY_VALUE (10) // 10 to 90 inclusive ) iodrp2_dq_ldm ( .AUXSDO (aux_sdi_out_ldm), .DATAOUT(), .DATAOUT2(), .DOUT (ioi_ldm), .DQSOUTN(), .DQSOUTP(), .SDO(), .TOUT (t_ldm), .ADD (ioi_drp_add), .AUXADDR (ioi_drp_addr), .AUXSDOIN (aux_sdi_out_4), .BKST (ioi_drp_broadcast), .CLK (ioi_drp_clk), .CS (ioi_drp_cs), .IDATAIN(), .IOCLK0 (ioclk90), .IOCLK1(), .MEMUPDATE (ioi_drp_update), .ODATAIN (ldm_oq), .SDI (ioi_drp_sdo), .T (ldm_t) ); end endgenerate //////////////////////////////////////////////// //IOBs instantiations // this part need more inputs from design team // for now just use as listed in fpga.v //////////////////////////////////////////////// //// Address genvar addr_i; generate for(addr_i = 0; addr_i < C_MEM_ADDR_WIDTH; addr_i = addr_i + 1) begin : gen_addr_obuft OBUFT iob_addr_inst (.I ( ioi_addr[addr_i]), .T ( t_addr[addr_i]), .O ( mcbx_dram_addr[addr_i]) ); end endgenerate genvar ba_i; generate for(ba_i = 0; ba_i < C_MEM_BANKADDR_WIDTH; ba_i = ba_i + 1) begin : gen_ba_obuft OBUFT iob_ba_inst (.I ( ioi_ba[ba_i]), .T ( t_ba[ba_i]), .O ( mcbx_dram_ba[ba_i]) ); end endgenerate // DRAM Control OBUFT iob_ras (.O(mcbx_dram_ras_n),.I(ioi_ras),.T(t_ras)); OBUFT iob_cas (.O(mcbx_dram_cas_n),.I(ioi_cas),.T(t_cas)); OBUFT iob_we (.O(mcbx_dram_we_n ),.I(ioi_we ),.T(t_we )); OBUFT iob_cke (.O(mcbx_dram_cke),.I(ioi_cke),.T(t_cke)); generate if (C_MEM_TYPE == "DDR3") begin : gen_ddr3_rst OBUFT iob_rst (.O(mcbx_dram_ddr3_rst),.I(ioi_rst),.T(t_rst)); end endgenerate generate if((C_MEM_TYPE == "DDR3" && (C_MEM_DDR3_RTT != "OFF" || C_MEM_DDR3_DYN_WRT_ODT != "OFF")) ||(C_MEM_TYPE == "DDR2" && C_MEM_DDR2_RTT != "OFF") ) begin : gen_dram_odt OBUFT iob_odt (.O(mcbx_dram_odt),.I(ioi_odt),.T(t_odt)); end endgenerate // Clock OBUFTDS iob_clk (.I(ioi_ck), .T(t_ck), .O(mcbx_dram_clk), .OB(mcbx_dram_clk_n)); //DQ genvar dq_i; generate for(dq_i = 0; dq_i < C_NUM_DQ_PINS; dq_i = dq_i + 1) begin : gen_dq_iobuft IOBUF gen_iob_dq_inst (.IO(mcbx_dram_dq[dq_i]),.I(ioi_dq[dq_i]),.T(t_dq[dq_i]),.O(in_pre_dq[dq_i])); end endgenerate // DQS generate if(C_MEM_TYPE == "DDR" || C_MEM_TYPE =="MDDR" || (C_MEM_TYPE == "DDR2" && (C_MEM_DDR2_DIFF_DQS_EN == "NO"))) begin: gen_dqs_iobuf IOBUF iob_dqs (.IO(mcbx_dram_dqs), .I(ioi_dqs),.T(t_dqs),.O(in_pre_dqsp)); end else begin: gen_dqs_iobufds IOBUFDS iob_dqs (.IO(mcbx_dram_dqs),.IOB(mcbx_dram_dqs_n), .I(ioi_dqs),.T(t_dqs),.O(in_pre_dqsp)); end endgenerate generate if((C_MEM_TYPE == "DDR" || C_MEM_TYPE =="MDDR" || (C_MEM_TYPE == "DDR2" && (C_MEM_DDR2_DIFF_DQS_EN == "NO"))) && C_NUM_DQ_PINS == 16) begin: gen_udqs_iobuf IOBUF iob_udqs (.IO(mcbx_dram_udqs), .I(ioi_udqs),.T(t_udqs),.O(in_pre_udqsp)); end else if(C_NUM_DQ_PINS == 16) begin: gen_udqs_iobufds IOBUFDS iob_udqs (.IO(mcbx_dram_udqs),.IOB(mcbx_dram_udqs_n), .I(ioi_udqs),.T(t_udqs),.O(in_pre_udqsp)); end endgenerate // DQS PULLDWON generate if(C_MEM_TYPE == "DDR" || C_MEM_TYPE =="MDDR" || (C_MEM_TYPE == "DDR2" && (C_MEM_DDR2_DIFF_DQS_EN == "NO"))) begin: gen_dqs_pullupdn PULLDOWN dqs_pulldown (.O(mcbx_dram_dqs)); end else begin: gen_dqs_pullupdn_ds PULLDOWN dqs_pulldown (.O(mcbx_dram_dqs)); PULLUP dqs_n_pullup (.O(mcbx_dram_dqs_n)); end endgenerate // DQSN PULLUP generate if((C_MEM_TYPE == "DDR" || C_MEM_TYPE =="MDDR" || (C_MEM_TYPE == "DDR2" && (C_MEM_DDR2_DIFF_DQS_EN == "NO"))) && C_NUM_DQ_PINS == 16) begin: gen_udqs_pullupdn PULLDOWN udqs_pulldown (.O(mcbx_dram_udqs)); end else if(C_NUM_DQ_PINS == 16) begin: gen_udqs_pullupdn_ds PULLDOWN udqs_pulldown (.O(mcbx_dram_udqs)); PULLUP udqs_n_pullup (.O(mcbx_dram_udqs_n)); end endgenerate //DM // datamask generation generate if( C_NUM_DQ_PINS == 16) begin : gen_udm OBUFT iob_udm (.I(ioi_udm), .T(t_udm), .O(mcbx_dram_udm)); end endgenerate OBUFT iob_ldm (.I(ioi_ldm), .T(t_ldm), .O(mcbx_dram_ldm)); endmodule
Go to most recent revision | Compare with Previous | Blame | View Log